Appraising efficacy of existing and advanced technologies for the remediation of beta-blockers from wastewater: A review

The discharge of emerging pollutants, such as beta-blockers (BB), has been recognized as one of the major threats to the environment due to the ecotoxicity associated with these emerging pollutants. The BB are prescribed to treat high blood pressure and cardiovascular diseases; however, even at lower concentration, these pollutants can pose eco-toxic impacts towards aquatic organisms. Additionally, owing to their recalcitrant nature, BB are not effectively removed through conventional technologies, such as activated sludge process, trickling filter and moving bed bioreactor; thus, it is essential to understand the degradation mechanism of BB in established as well as embryonic technologies, like adsorption, electro-oxidation, Fenton process, ultraviolet-based advance oxidation process, ozonation, membrane systems, wetlands and algal treatment. In this regard, this review articulates the recalcitrant nature of BB and their associated removal technologies. Moreover, the major advantages and limitations of these BB removal technologies along with the recent advancements with regard to the application of innovative materials and strategies have also been elucidated. Therefore, the present review intends to aid the researchers in improving the BB removal efficiency of these technologies, thus alleviating the problem of the release of BB into the environment.

Performance evaluation of microbial fuel cell using novel anode architecture and with low cost components

Microbial fuel cell (MFC) has proved to be an effective technology for treatment of wastewater with additional advantage of electricity generation. Though the power density obtained has increased many- folds over a last decade, the cost of treatment and cost of the electricity generation need to be brought down to make the process feasible. In the present research, an attempt has been made to use locally available, low cost and effective materials for the construction of the MFC using novel anode architecture. The MFC was made using multiple membranes in the single cell. The special design of anode proved to be very effective in getting higher power density. The volumetric power density of 2002 mW/m3 could be achieved without use of any chemical catholyte. The corresponding Coulombic efficiency obtained was 13.17%. When chemical catholyte was used, the power density increased to 5201 mW/m3, an increase by more than 2.5 times. The corresponding Coulombic efficiency of the MFC also increased to 29.16 %. Such novel anode architecture could take this technology step forward for practical implementation to harvest carbon neutral electricity from wastewater. The performance of MFC in the removal of COD from wastewater was found to be 93.9 to 97.75% which is highly satisfactory. The removal efficiency was found to be independent of the initial COD of the substrate.

Waste-derived iron catalyzed bio-electro-Fenton process for the cathodic degradation of surfactants

The application of waste-derived iron for reuse in wastewater treatment is an effective way of utilizing waste and attaining sustainability in the overall process. In the present investigation, bio-electro-Fenton process was initiated for the cathodic degradation of surfactants using waste-iron catalyzed MFC (WFe-MFC). The waste-iron was derived from spent tonner ink using calcination at 600 °C. Three surfactants namely, sodium dodecyl sulphate (SDS), cetyltrimethylammonium bromide, and Triton x-100 were selected as target pollutants. The effect of experimental factors like application of catalyst, contact time, external resistance, and anodic substrate concentration on the SDS degradation was investigated. At a neutral pH, the cathodic surfactants removal efficiency in WFe-MFC was above 85% in a contact time of 180 min with the initial surfactant concentration of ∼20 mg L^-1 and external resistance of 100 Ω. The long-term operation using secondary treated real wastewater with unchanged cathode proved that the catalyst was still active to produce effluent SDS concentration of less than 1 mg L^-1 in 4 h of contact time after 16 cycles. In a way, the present investigation suggests a potential application for spent tonner ink in the form of Fenton catalyst for wastewater treatment via bio-electro-Fenton MFC.

Optimum dose of Chaetoceros for controlling methanogenesis to improve power production of microbial fuel cell

The marine algae Chaetoceros contains hexadecatrienoic acid, which suppresses methanogen development and improves the coulombic efficiency (CE) of microbial fuel cells (MFC). To inhibit the methanogens, optimum concentration of marine algae should be added to the anaerobic sludge to enhance the performance of MFC. A varying concentration of Chaetoceros ranging from 1 to 20 mg/mL was carried out for pretreatment of an anaerobic-mix consortium to suppress methanogens. MFC inoculated with pretreated anaerobic sludge with 10 mg/mL Chaetoceros showed a maximum power density of 21.62 W/m³ and a maximum CE of 37.25%, which was considerably higher than the treatment with other concentrations. At 10 mg/mL concentration, Tafel analysis of the anode in the MFC showed a higher exchange current density of 66.35 mA/m² and a lower charge transfer resistance of 0.97 Ω.m², revealing higher bio-electrochemical activity. The performance of MFC improved when the concentration of Chaetoceros was increased up to 10 mg/mL, but then began to decline as the concentration increased further. Thus, the optimum dose of Chaetoceros to be added in the mix-anaerobic consortium to optimize the power performance of MFC was determined, which can be carried out in scaled-up MFCs.

Efficacious bioremediation of heavy metals and radionuclides from wastewater employing aquatic macro- and microphytes

Cytotoxic, mutagenic, and carcinogenic contaminants, such as heavy metals and radionuclides, have become an alarming environmental concern globally, especially for developed and developing nations. Moreover, inefficient prevalent wastewater treatment technologies combined with increased industrial activity and modernization has led to increase in the concentration of toxic metals and radioactive components in the natural water bodies. However, for the improvement of ecosystem of rivers, lakes, and other water sources different physicochemical methods such as membrane filtration, reverse osmosis, activated carbon adsorption, electrocoagulation, and other electrochemical treatment are employed, which are uneconomical and insufficient for the complete abatement of these emerging pollutants. Therefore, the application of bioremediation employing aquatic macrophytes and microphytes have gained considerable importance owing to the benefits of cost-effectiveness, eco-friendly, and higher energy efficiency. Thus, the present review aims to enlighten the readers on the potential application of algae, cyanobacteria, plant, and other aquatic micro- and macrophytes for the elimination of carcinogenic metals and radioactive isotopes from wastewater. Additionally, the use of transgenic plants, genetically modified species, algal-bacterial symbiosis for the enhancement of removal efficiency of mutagenic contaminants are also highlighted. Furthermore, species selection based on robustness, mechanism of different pathways for heavy metal and radionuclide detoxification are elucidated in this review article.

A review on environmental occurrence, toxicity and microbial degradation of Non-Steroidal Anti-Inflammatory Drugs (NSAIDs)

In recent years, Non-Steroidal Anti-Inflammatory Drugs (NSAIDs) have surfaced as a novel class of pollutants due to their incomplete degradation in wastewater treatment plants and their inherent ability to promote physiological predicaments in humans even at low doses. The occurrence of the most common NSAIDs (diclofenac, ibuprofen, naproxen, and ketoprofen) in river water, groundwater, finished water samples, WWTPs, and hospital wastewater effluents along with their toxicity effects were reviewed. The typical concentrations of NSAIDs in natural waters were mostly below 1 μg/L, the rivers receiving untreated wastewater discharge have often showed higher concentrations, highlighting the importance of effective wastewater treatment. The critical analysis of potential, pathways and mechanisms of microbial degradation of NSAIDs were also done. Although studies on algal and fungal strains were limited, several bacterial strains were known to degrade NSAIDs. This microbial ability is attributed to hydroxylation by cytochrome P450 because of the decrease in drug concentrations in fungal cultures of Phanerochaete sordida YK-624 on incubation with 1-aminobenzotriazole. Moreover, processes like decarboxylation, dehydrogenation, dechlorination, subsequent oxidation, demethylation, etc. also constitute the degradation pathways. A wide array of enzymes like dehydrogenase, oxidoreductase, dioxygenase, monooxygenase, decarboxylase, and many more are upregulated during the degradation process, which indicates the possibility of their involvement in microbial degradation. Specific hindrances in upscaling the process along with analytical research needs were also identified, and novel investigative approaches for future monitoring studies are proposed.

Seasonal characterization of municipal solid waste for selecting feasible waste treatment technology for Guwahati city, India

As quantities and composition of municipal solid waste (MSW) vary significantly with seasons, a seasonal characterization study is critical for developing an efficient MSW management system. MSW was characterized in three different seasons for selecting an appropriate waste treatment and management strategy for Guwahati city. Results of the study shows that the major components of the MSW were organics (42.2%) and plastic wastes (25.2%), which show high variations on a seasonal basis (22-49%). The chemical characterization of MSW revealed that on seasonal basis moisture content varies between 43.4% and 58.3%, pH between 5.5 and 6.5, volatile solid content from 32.9 to 58.9%, and the calorific value between 1203 and 3015 kcal/kg. Waste collected in the present study was a mixture of organics, recyclables, and inert material which is difficult and uneconomical for treatment in its present form. However, with proper waste segregation, bio-methanation, and composting could be sustainable waste treatment solutions due to the high moisture and volatile content of the MSW. Due to inadequate quantity, low calorific values, requirement of skilled supervision, and high capital investment, the thermochemical conversion of MSW may not be economically feasible for the present case.Implications: Present study is a novel attempt to analyze in-depth variation in the municipal solid waste (MSW) composition and properties in different seasons and how does it influence the selection and feasibility of the available waste treatment technologies. Search on Google scholar shows that only seven articles have been published till now which evaluated seasonal impact of MSW. Out to these published studies only one study have calculated energy potential of MSW on seasonal basis which is mainly restricted to incineration only. In-depth analysis of seasonal variation on anaerobic digestion, composting, refuse derived fuel (RDF), pyrolysis, and gasification is yet to determine. Furthermore, to best of our knowledge so far in India there was no such in-depth study has been published related to seasonal variation in MSW on large scale (city level). Present study provides in-depth valuable information regarding degree of variation in MSW composition and how does it affect resource recovery out of waste, which was not studied before in-depth before. Outcomes of the present study will definitely assist engineers and policymaker involved MSW management and planning for large urban areas to fulfil their sustainability goals.

Effectiveness of constructed wetland integrated with microbial fuel cell for domestic wastewater treatment and to facilitate power generation

Constructed wetlands (CWs) have gained a lot of attention for wastewater treatment due to robustness and natural pollutant mitigation characteristics. This widely acknowledged technology possesses enough merits to derive direct electricity in collaboration with microbial fuel cell (MFC), thus taking advantage of microbial metabolic activities in the anoxic zone of CWs. In the present study, two identical lab-scale CWs were selected, each having 56 L capacity. One of the CW integrated with MFC (CW-MFC) contains two pairs of electrodes, i.e., carbon felt and graphite plate. The first pair of CW-MFC consists of a carbon felt cathode with a graphite plate anode, and the second pair contains a graphite plate cathode with a carbon felt anode. The other CW was not integrated with MFC and operated as a traditional CW for evaluating the performance. CW-MFC and CW were operated in continuous up-flow mode with a hydraulic retention time of 3 days and at different organic loading rates (OLRs) per unit surface area, such as 1.45 g m^-2 day^-1 (OLR-1), 2.43 g m^-2 day^-1 (OLR-2), and 7.25 g m^-2 day^-1 (OLR-3). The CW-MFC was able to reduce the organic matter, phosphate, and total nitrogen by 92%, 93%, and 70%, respectively, at OLR of 1.45 g m^-2 day^-1, which was found to be higher than that obtained in conventional CW. With increase in electrochemical redox activities, the second pair of electrodes made way for 3 times higher power density of 16.33 mW m^-2 as compared to the first pair of electrodes in CW-MFC (5.35 mW m^-2), asserting carbon felt as a good anode material to be used in CW-MFC. The CW-MFC with carbon felt as an anode material is proposed to improve the electro-kinetic activities for scalable applications to achieve efficient domestic wastewater treatment and electricity production.

Ameliorating effect of nitrate on nitrite inhibition for denitrifying P-accumulating organisms

Lowered air supply and organic carbon need are the key factors to reduce wastewater treatment costs and thereby, avoid eutrophication. Denitrifying PO₄^3-- removal (DPR) process using nitrate instead of oxygen for PO₄^3- uptake was started up in the sequencing batch reactor (SBR) at a nitrate dosing rate of 20-25 mg N L^-1 d^-1. Operation with a real municipal wastewater supplied with CH₃COONa, K₂HPO₄ and KNO₃ succeeded in the cultivation of biomass containing denitrifying polyphosphate accumulating organisms (DPAOs). The durations of SBR process anaerobic/anoxic/oxic cycles were 1.5 h, 3.5 h and 1 h, respectively. SBR operation resulted in a maximum PO₄^3--P uptake of 17 mg PO₄^3--P g^-1 MLSS. The highest TN and PO₄^3- removal efficiencies were observed during the first half of reactor operation at 77 (±10) % and 71 (±5) %, respectively. An average COD removal rate of 172 (±98) mg g^-1 MLSS and a high average removal efficiency of 89 (±4) % were achieved. Nitrite effect with/without nitrate as DPR electron acceptor was investigated in batch-scale to show possibilities to use high nitrite and nitrate contents simultaneously as electron acceptors for the anoxic phosphate uptake. Nitrate attenuation against nitrite toxicity can be economically justified in full-scale treatment applications in which wastewater has a high nitrogen content. Nitrate attenuated nitrite toxicity (caused by nitrite content at 5-100 mg NO₂^--N L^-1) when using supplemental additions of nitrate (at concentrations of 45-200 mg NO₃^--N L^-1) in batch tests. Illumina sequencing emphasized that during biomass adaption microbial community changed by lowered aerobic cycle length and by lowered nitrate dosing towards representation of key DPAO/PAO- organisms, such as Candidatus Accumulibacter, Xanthomonadaceae, Comomonadaceae, Saprospiraceae and Rhodocyclaceae. This study showed that DPAO biomass adaption to nitrate maintained an efficient COD, nitrogen and phosphorus removal and the biomass can be applied for treatment of wastewater containing high nitrite and nitrate content.

Two-phase anaerobic digestion of food waste: Effect of semi-continuous feeding on acidogenesis and methane production

In present investigation, effect of diverting acidogenic off-gas from leached bed reactor (LBR) to up-flow anaerobic sludge blanket (UASB) reactor during semi-continuous food waste (FW) anaerobic digestion was evaluated. In test LBR headspace pressure (3.3 psi) was maintained with intermittent headspace gas transfer into UASB. In control, same headspace pressure was maintained without gas transfer. The semi-continuous FW addition affected the characteristics and production of leachate in control and test LBR. The cumulative COD, total soluble products and methane yields were 1.26, 1.37 and 3 times higher in the test LBR than the control. The acetate and methane yields from test LBR were 697.8 g·kgVS_added^-1 and 167.55 mL·gCOD^-1feeding. Acidogenic gas transfer maintained low partial pressure of hydrogen and the hydrogen to carbon-di-oxide ratio in the headspace of LBR, which were thermodynamically favorable for microbial metabolism and concomitant high-rate production of acetate-rich volatile fatty acid and methane-rich biogas from FW.

Live diatoms as potential biocatalyst in a microbial fuel cell for harvesting continuous diafuel, carotenoids and bioelectricity

Microbial fuel cell (MFC) with live diatoms (Nitzschia palea) displacing bacteria in the anodic chamber generated electrical potential. Unlike other microalgae, diatoms fix 25% of atmospheric CO₂, thus releasing O₂. They perform photolysis of water by photosynthesis in the plastid during light photoperiod and cellular respiration in the mitochondria during dark, producing electrons and protons, respectively. The electrogenic property of diatom was explored and evaluated by comparing the potential changes with reference fuel cell without diatoms and that operated with diatoms in the anodic chamber. Such photosynthetic diatom microbial fuel cell (PDMFC) employed f/2 media rich in nitrates, phosphates, metasilicates, trace metals and vitamins as the anolyte and potassium permanganate as catholyte enhanced the output voltage by 3^rd day. The maximum power density for PDMFC was 12.62 mWm^-2 and coulombic efficiency of 22.95%. Besides this, the fixed diatom cells at anode showed about 64.28% increase in lipid production on 15th day compared to that on 1st day along with the increment in formation of complex fatty acid methyl esters and carotenoids during its operation. Hence, diatoms can be envisaged to substitute bacteria in the anodic chamber of MFC to simultaneously produce bioelectricity and other valuable compounds. Further their silica nanoporous architecture serve as good absorbents for heavy metal removal found in many wastewaters.

Bacterial signalling mechanism: An innovative microbial intervention with multifaceted applications in microbial electrochemical technologies: A review

Microbial electrochemical technologies (METs) are a set of inventive tools that generate value-added by-products with concomitant wastewater remediation. However, due to the bottlenecks, like higher fabrication cost and inferior yield of resources, these inventive METs are still devoid of successful field-scale implementation. In this regard, application of quorum sensing (QS) mechanism to improve the power generation of the METs has gained adequate attention. The QS is an intercellular signalling mechanism that controls the bacterial social network in its vicinity via the synthesis of diffusible signal molecules labelled as auto inducers, thus ameliorating yield of valuables produced through METs. This state-of-the-art review elucidates different types of QS molecules and their working mechanism with the special focus on the widespread application of QS in the field of METs for their performance enhancement. Thus, this review intends to guide the researchers in rendering scalability to METs by integrating innovative QS mechanisms into them.

Microbial fuel cell coupled Fenton oxidation for the cathodic degradation of emerging contaminants from wastewater: Applications and challenges

Urbanization and industrialization have resulted in the escalation of the occurrence of emerging contaminants (EC) in the wastewater and ultimately to the receiving water bodies due to their bio-refractory nature. The presence of ECs in the water bodies adversely affects all three domains of life, viz. bacteria, archaea and eukaryotes, and eventually the ecosystem. Fenton oxidation is one of the most suitable method that is capable of degrading a variety of ECs by employing a strong oxidizing agent in the form of •OH. The coupling of Fenton oxidation with microbial fuel cell (MFC) offers benefits, such as low-cost, minimal requirement of external energy, and in-situ generation of oxidizing agents. The resulting system, termed as bio-electro-Fenton MFC (BEF-MFC), is capable of degrading the ECs in the cathodic chamber, while harvesting bioelectricity and simultaneously removing oxidizable organic matter from wastewater in the anodic chamber. This review discusses the applications of BEF-MFC for the treatment of dyes, pharmaceuticals, pesticides, and real complex wastewaters. Additionally, the effect of operating conditions on the performance of BEF-MFC are elaborated and emphasis is also given on possible future direction of research that can be adopted in BEF-MFC in the purview of up-scaling.

Role of bioelectrochemical systems for the remediation of emerging contaminants from wastewater: A review

Bioelectrochemical systems (BESs) are a unique group of wastewater remediating technology that possesses the added advantage of valuable recovery with concomitant wastewater treatment. Moreover, due to the application of robust microbial biocatalysts in BESs, effective removal of emerging contaminants (ECs) can be accomplished in these BESs. Thus, this review emphasizes the recent demonstrations pertaining to the removal of complex organic pollutants of emerging concern present in wastewater through BES. Owing to the recalcitrant nature of these pollutants, they are not effectively removed through conventional wastewater treatment systems and thereby are discharged into the environment without proper treatment. Application of BES in terms of ECs removal and degradation mechanism along with valuables that can be recovered are discussed. Moreover, the factors affecting the performance of BES, like biocatalyst, substrate, salinity, and applied potential are also summarized. In addition, the present review also elucidates the occurrence and toxic nature of ECs as well as future recommendations pertaining to the commercialization of this BES technology for the removal of ECs from wastewater. Therefore, the present review intends to aid the researchers in developing more efficient BESs for the removal of ECs from wastewater.

A novel bio-electro-Fenton process for eliminating sodium dodecyl sulphate from wastewater using dual chamber microbial fuel cell

The frequent occurrence of surfactants in urban wastewaters represents a multifaceted environmental concern. In this investigation, bio-electro-Fenton-microbial fuel cell (BEF-MFC) was developed for the degradation of sodium dodecyl sulphate (SDS) from wastewater. The synthesised cathode catalyst (powdered activated carbon and iron oxide) facilitated the Fenton reaction in the cathodic chamber of the MFC, concurrently generating a maximum power density of 105.67 mW m^-2. The overall performance of the BEF-MFC for SDS removal and power generation excelled the control MFC (C-MFC) having carbon black coated cathode under similar operating conditions. Although, the rate of SDS degradation was favourable in acidic pH, under neutral pH, 70.8 ± 6.4% of SDS degradation was achieved in 120 min in BEF-MFC. A comparison of environmental impacts of BEF-MFC with up-flow MFC and electrochemical oxidation using life cycle assessment tool suggests that BEF-MFC can be one of the promising technologies for the tertiary treatment of wastewater.

High throughput techniques for the rapid identification of electroactive microorganisms

Electroactive microorganisms (EAM), capable of executing extracellular electron transfer (EET) in/out of a cell, are employed in microbial electrochemical technologies (MET) and bioelectronics for harnessing electricity from wastewater, bioremediation and as biosensors. Thus, investigation on EAM is becoming a topic of interest for multidisciplinary areas, such as environmental science, energy and health sectors. Though, EAM are widespread in three domains of life, nevertheless, only a few hundred EAM have been identified so far and hence, the rapid identification of EAM is imperative. In this review, the techniques that are developed for the direct identification of EAM, such as azo dye and WO₃ based techniques, dielectrophoresis, potentiostatic/galvanometric techniques, and other indirect methods, such as spectroscopy and molecular biology techniques, are highlighted with a special focus on time required for the detection of these EAM. The bottlenecks for identifying EAM and the knowledge gaps based on the present investigations are also discussed. Thus, this review is intended to encourage researchers for devolving high-throughput techniques for identifying EAM with more accuracy, while consuming less time.

Application of microbial electrochemical technologies for the treatment of petrochemical wastewater with concomitant valuable recovery: A review

Petrochemical industry is one of the major and rapidly growing industry that generates a variety of toxic and recalcitrant organic pollutants as by-products, which are not only harmful to the aquatic animals but also affects human health. The majority of the components of petrochemical wastewater (PW) are carcinogenic, genotoxic and phytotoxic in nature; hence, this complex wastewater generated from different petrochemical processes should be efficiently treated prior to its disposal in natural water bodies. The established technologies like advanced oxidation, membrane bioreactor, electrocoagulation and activated sludge process employed for the treatment of PW are highly energy intensive and incurs high capital and operation cost. Moreover, these technologies are not effective in completely eliminating petroleum hydrocarbons present in PW. Thus, to reduce the energy requirement and also to transform the chemical energy trapped in these organic matters present in this wastewater into bioelectricity and other value-added products, microbial electrochemical technologies (METs) can be efficaciously used, which would also compensate the treatment cost by transforming these pollutants into bioenergy and valuables. In this regard, this review elucidates the feasibility and application of different METs as an appropriate alternative for the treatment of PW. Furthermore, the numerous bottlenecks towards the real-life application and commercialization of pioneering METs have also been articulated.

Testing of Chemically Activated Cellulose Fibers as Adsorbents for Treatment of Arsenic Contaminated Water

Exposure to different arsenic concentrations (higher than 10 μg/L), either due to the direct consumption of contaminated drinking water or indirectly by using contaminated food is harmful for human health. Therefore, it is important to remove arsenic from aqueous solutions. Among many arsenic removal technologies, adsorption offers a promising solution with a good efficiency, however the material used as adsorbent play a very vital role. The present investigation evaluated the behavior of two cellulose-based adsorbent materials, i.e., viscose fibers (V) and its TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl) derivative, obtained by using the well-established TEMPO-mediated protocol (VF). Due to the known arsenic affinity for Fe ions the two materials were later doped with it. This was done after a preliminary functionalization with di-2-ethylhexyl phosphoric acid (DEHPA), to obtain two materials: V-DEHPA-Fe and VF-DEHPA-Fe. Arsenic adsorption is known to be pH dependent (between 6 and 8); therefore, the optimal pH range for As(V) adsorption has been established. In order to evaluate the adsorption mechanism for both the synthesized materials, the influence of contact time, temperature and initial concentration was evaluated. Langmuir, Freundlich and Sips equilibrium isotherm models were used in order to determine the ability of the model to describe As(V) adsorption process. The maximum adsorption capacity of the material V-DEHPA-Fe was 247.5 µg As(V)/g with an As(V) initial concentration of 5 mg/L and for the material VF-DEHPA-Fe it was 171.2 µg As(V)/g with initial concentration of 5 mg/L.

Palladium-Supported Zirconia-Based Catalytic Degradation of Rhodamine-B Dye from Wastewater

The catalytic activity of Pd/ZrO2 was studied in terms of the degradation of rhodamine-B dye in the presence of hydrogen peroxide. Pd/ZrO2 was prepared by impregnation method, calcined at 750 °C and characterized by XRD, SEM and EDX. The catalyst showed good catalytic activity for dye degradation at 333 K, using 0.05 g of the catalyst during 5 h. The reaction kinetics followed the pseudo-first order kinetics. The Freundlich, Langmuir and Temkin isotherms were applied to the data and the best fit was obtained with Freundlich isotherm. Thermodynamic parameters, like ΔH, ΔG and ΔS were also calculated. The negative values of ΔH (−291.406 KJ/mol) and Gibbs free energy (ΔG) showed the exothermic and spontaneous nature of the process. The positive ΔS (0.04832 KJ/mol K) value showed suitable affinity of catalyst for dye degradation. The catalyst was very stable, active and was easily separated from the reaction mixture by filtration. It can be concluded from the results that the prepared catalyst could be effectively used in dyes degradation/removal from water subjected to further validation and use for various dyes.

Preparation of Activated Carbon from the Wood of Paulownia tomentosa as an Efficient Adsorbent for the Removal of Acid Red 4 and Methylene Blue Present in Wastewater

Paulownia tomentosa, a woody plant that is widely found in Pakistan and in other regions of the world, was used as a raw material to prepare activated carbon using chemical and physical activation methods. Adsorption of the dyes- acid red 4 and methylene blue onto the prepared activated carbon were analyzed by batch experiments. The impacts of different adsorption parameters such as pH, temperature, contact time, initial dye concentration and adsorbent dosage were also evaluated. Equilibrium data were fitted into various isotherm models such as: Langmuir, Temkin and Freundlich. High regression values were achieved with Langmuir isotherm model. Different kinetic adsorption models such as pseudo-first-order, pseudo-second-order and intra-particle diffusion model models were applied. The adsorption kinetics was found to be best-fitted into pseudo-second-order kinetic model. The optimum pH for acid red 4 was around 1 while for methylene blue it was 8. The optimum adsorbent dosage was 0.3 g for both dyes used. The activation energy (Ea) values were 30.57 and 3.712 kJ/mol, respectively for acid red 4 and methylene blue while the enthalpy (ΔH) and entropy (ΔS) values were correspondingly as 24.88/1.1927 kJ/mol and −2843.32/−0.329 J·mol/K for the mentioned dyes. The experimental result showed that the prepared activated carbon was the best in the removal of acid red 4 and methylene blue from aqueous media and therefore, could be preferably used as cheap adsorbent in wastewater treatment.

Proficient Sanitary Wastewater Treatment in Laboratory and Field-Scale Microbial Fuel Cell with Anti-Biofouling Cu 0.5 Mn 0.5 Fe 2 O 4 as Cathode Catalyst

For successful field-scale application of microbial fuel cell (MFC), the power recovery from field-scale MFC needs to be improved considerably with simultaneous reduction in its fabrication cost. These problems can be addressed by applying low-cost and efficient cathode catalyst in MFCs. In this regard, Cu0.5Mn0.5Fe2O4 (CuMnFe) was synthesized and applied as cathode catalyst in lab and field-scale MFCs with capacity of 150 ml and 25 l, respectively. Lab-scale MFC having CuMnFe as cathode catalyst demonstrated power density of 176.0 ± 8.2 mW m−2, which was competitive with MFC having Pt as cathode catalyst (183.0 ± 12.6 mW m−2) and it was about seven times higher than control MFC (25.5 ± 4.5 mW m−2) having no catalyst. Application of CuMnFe as cathode catalyst in field-scale MFC produced power density of 7.74 mW m−2, which was three-times higher than the power produced by the field-scale MFC operated without any cathode catalyst (2.58 mW m−2). The cathode catalyst CuMnFe also demonstrated excellent anti-biofouling properties, which in turn improved the power production of field-scale MFC. Therefore, low-cost CuMnFe can be anticipated as an efficacious cathode catalyst for application in MFCs that would produce long term stable higher power, while offering simultaneous treatment to wastewater.

Preparation of Pd–Ni Nanoparticles Supported on Activated Carbon for Efficient Removal of Basic Blue 3 from Water

Pd–Ni nanoparticles supported on activated carbon (Pd–Ni/AC) were prepared using a phase transfer method. The purpose of synthesizing ternary composites was to enhance the surface area of synthesized Pd–Ni nanoparticles, as they have a low surface area. The resulting composite was characterized by scanning electronic microscopy (SEM), X-ray diffraction (XRD) and energy-dispersive X-ray spectroscopy (EDX) for investigating its surface morphology, particle size, percentage of crystallinity and elemental composition, respectively. The XRD data and EDX analysis revealed the presence of Pd–Ni alloys impregnated on the AC. Pd–Ni/AC was used as an adsorbent for the removal of the azo dye basic blue 3 from an aqueous medium. Kinetic and isotherm models were used to calculate the adsorption parameters. The most suitable kinetic model amongst the applied models was the pseudo-second-order model, confirming the chemisorption characteristics of the process, and the most suitable isotherm model was the Langmuir model, with a maximum adsorption capacity of 333 mg/g at 333 K. Different experimental parameters, such as the adsorbent dosage, pH, temperature and contact time, were optimized. The optimum parameters reached were: a pH of 12, temperature of 333 K, adsorbent dosage of 0.01 g and optimum contact time of 30 min. Moreover, the thermodynamics parameters of adsorption, such as Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°), showed the adsorption processes being exothermic with values of ΔH° equal to −6.206 kJ/mol and being spontaneous with ΔG° values of −13.297, −13.780 and −14.264 kJ/mol, respectively at 293, 313 and 333 K. An increase in entropy change (ΔS°) with a value of 0.0242 kJ/mol K, indicated the enhanced disorder at a solid–solution interface during the adsorption process. Recycling the adsorbent for six cycles with sodium hydroxide and ethanol showed a decline in the efficiency of the selected azo dye basic blue 3 up to 79%. The prepared ternary composite was found effective in the removal of the selected dye. The removal of other pollutants represents one of the possible future uses of the prepared adsorbent, but further experiments are required.

Start-Up of Anammox SBR from Non-Specific Inoculum and Process Acceleration Methods by Hydrazine

Biological nutrient removal from wastewater to reach acceptable levels is needed to protect water resources and avoid eutrophication. The start-up of an anaerobic ammonium oxidation (anammox) process from scratch was investigated in a 20 L sequence batch reactor (SBR) inoculated with a mixture of aerobic and anaerobic sludge at 30 ± 0.5 °C with a hydraulic retention time (HRT) of 2–3 days. The use of NH4Cl, NaNO2, and reject water as nitrogen sources created different salinity periods, in which the anammox process performance was assessed: low (<0.2 g of Cl−/L), high (18.2 g of Cl−/L), or optimum salinity (0.5–2 g of Cl−/L). Reject water feeding gave the optimum salinity, with an average nitrogen removal efficiency of 80%, and a TNRR of 0.08 kg N/m3/d being achieved after 193 days. The main aim was to show the effect of a hydrazine addition on the specific anammox activity (SAA) and denitrification activity in the start-up process to boost the autotrophic nitrogen removal from scratch. The effect of the anammox intermediate hydrazine addition was tested to assess its concentration effect (range of 2–12.5 mg of N2H4/L) on diminishing denitrifier activity and accelerating anammox activity at the same time. Heterotrophic denitrifiers’ activity was diminished by all hydrazine additions compared to the control; 5 mg of N2H4/L added enhanced SAA compared to the control, achieving an SAA of 0.72 (±0.01) mg N/g MLSS/h, while the test with 7.5 mg of N2H4/L reached the highest overall SAA of 0.98 (±0.09) mg N g/MLSS/h. The addition of trace amounts of hydrazine for 6 h was also able to enhance SAA after inhibition by organic carbon source sodium acetate addition at a high C/N ratio of 10/1. The start-up of anammox bacteria from the aerobic–anaerobic suspended biomass was successful, with hydrazine significantly accelerating anammox activity and decreasing denitrifier activity, making the method applicable for side-stream as well as mainstream treatment.

Enhancing the Performance of Microbial Fuel Cell by Using Chloroform Pre-treated Mixed Anaerobic Sludge to Control Methanogenesis in Anodic Chamber

Formation of methane in the anodic chamber of a microbial fuel cell (MFC) indicates an energy inefficiency in electricity generation as the energy required for electrogenesis gets redirected to methanogenesis. The hypothesis of this research is that inhibition of methanogenesis in the mixed anaerobic anodic inoculum is associated with an enhanced activity of the electrogenic bacterial consortia. Hence, the primary objective of this investigation is to evaluate the ability of chloroform to inhibit the methanogenesis at different dosing to enhance the activity of electrogenic consortia in MFC. A higher methane inhibition and hence an enhanced performance of MFC was achieved when mixed anaerobic sludge, collected from septic tank, was used as inoculum after pre-treatment with 0.25% (v/v) chloroform dosing (MFC-0.25_CF). The MFC-0.25_CF attained a maximum power density of 8.51 W/m³, which was more than twice as that of MFC inoculated with untreated sludge. Also, a clear correlation between the chloroform dosing, methane inhibition, wastewater treatment, and power generation was established, which demonstrated the effectiveness of the technique in enhancing power generation in MFC along with adequate biodegradation of organic matter present in wastewater at an optimum chloroform dosing of 0.25% (v/v) to inhibit methanogenesis.

Plant secondary metabolites induced electron flux in microbial fuel cell: investigation from laboratory-to-field scale

Wastewater treatment coupled with electricity recovery in microbial fuel cell (MFC) prefer mixed anaerobic sludge as inoculum in anodic chamber than pure stain of electroactive bacteria (EAB), due to robustness and syntrophic association. Genetic modification is difficult to adopt for mixed sludge microbes for enhancing power production of MFC. Hence, we demonstrated use of eco-friendly plant secondary metabolites (PSM) with sub-lethal concentrations to enhance the rate of extracellular electron transfer between EAB and anode and validated it in both bench-scale as well as pilot-scale MFCs. The PSMs contain tannin, saponin and essential oils, which are having electron shuttling properties and their addition to microbes can cause alteration in cell morphology, electroactive behaviour and shifting in microbial population dynamics depending upon concentrations and types of PSM used. Improvement of 2.1-times and 3.8-times in power densities was observed in two different MFCs inoculated with Eucalyptus-extract pre-treated mixed anaerobic sludge and pure culture of Pseudomonas aeruginosa, respectively, as compared to respective control MFCs operated without adding Eucalyptus-extract to inoculum. When Eucalyptus-extract-dose was spiked to anodic chamber (125 l) of pilot-scale MFC, treating septage, the current production was dramatically improved. Thus, PSM-dosing to inoculum holds exciting promise for increasing electricity production of field-scale MFCs.

Methanogenesis inhibitors used in bio-electrochemical systems: A review revealing reality to decide future direction and applications

Microbial fuel cell (MFC) is a robust technology capable of treating real wastewaters by utilizing mixed anaerobic microbiota as inoculum for producing electricity from oxidation of the biodegradable matters. However, these mixed microbiota comprises of both electroactive microorganisms (EAM) and substrate/electron scavenging microorganisms such as methanogens. Hence, in order to maximize bioelectricity from MFC, different physio-chemical techniques have been applied in past investigations to suppress activity of methanogens. Interestingly, recent investigations exhibit that methanogens can produce electricity in MFC and possess the cellular machinery like cytochrome c and Type IV pili to perform extracellular electron transfer (EET) in the presence of suitable electron acceptors. Hence, in this review, in-depth analysis of versatile behaviour of methanogens in both MFC and natural anaerobic conditions with different inhibition techniques is explored. This review also discusses the future research directions based on the latest scientific evidence on role of methanogens for EET in MFC.