Miniaturized amperometric flow immunoassay system using a glass fiber membrane modified with anion

The preparation of reagentless electrochemical immunosensor based on a nano-gold and chitosan hybrid film for human chorionic gonadotrophin

A novel amperometric immunosensor for determination of human serum chorionic gonadotrophin (hCG) was constructed by immobilizing hCG antibody with nano-gold and chitosan (CHIT) hybrid film electrochemical co-deposited on a glassy carbon electrode. The fabricated procedures and electrochemical behaviors of proteins on such an interface were characterized with electrochemical impedance, cyclic voltammetry and chronoamperometry. The effect of incubation time on the electrochemical behavior of immunosensor was studied and other experimental conditions such as mass ratio of CHIT and HAuCl4, depositing time of hybrid film, the pH, and temperature were studied too. The current response of the immunosensor is in linear relationship with concentration of hCG. The resulting immunosensor offers an excellent amperometric response for hCG ranging from 0.20 to 100 mIU mL(-1) with a detection limit of 0.1 mIU mL(-1). A satisfactory determination of hCG in serum samples can be obtained by this immunosensor.

Electrochemical detection of HbA1c, a maker for diabetes, using a flow immunoassay system

An on-chip electrochemical flow immunoassay system for the detection of hemoglobin A1c (HbA1c) was developed using anti-human hemoglobin (Hb) IgG labeled with ferrocene monocarboxylic acid (Fc-COOH) and boronate-affinity chromatography. An on-chip column packed with boronate-activated agarose beads was used for the separation of HbA1c from both non-glycated Hb and free antibody. Anti-human Hb IgG conjugated to Fc-COOH (Fc-IgG) was used for the electrochemical detection of HbA1c. The assay procedure included immunoreactions with Fc-IgG and HbA1c, separation of immunocomplexes by boronate affinity, and electrochemical detection of Fc-IgG-HbA1c immunocomplexes. The immunoreaction mixtures were injected onto a boronate-affinity column. HbA1c-antibody complexes were then trapped onto the column by the affinity of HbA1c to boronic acid. Subsequently, elution buffer containing sorbitol was applied to elute HbA1c-antibody complexes and a current was detected by applying 600 mV versus Ag/AgCl. The elution signal was an estimation of the HbA1c amount. A linear correlation between the increase of current and HbA1c concentration was obtained up to an HbA1c concentration of 500 microg/ml. The HbA1c flow immunoassay was successfully achieved using hemolysates. This electrochemical flow immunoassay system enabled us to construct a novel point-of-care testing device for the monitoring of glycated proteins including HbA1c.

Surface characterization of 3-glycidoxypropyltrimethoxysilane films on silicon-based substrates

Silane coupling agents are commonly used to activate surfaces for subsequent immobilization of biomolecules. The homogeneity and surface morphology of silane films is important for controlling the structural order of immobilized single-stranded DNA probes based on oligonucleotides. The surfaces of silicon wafers and glass slides with covalently attached 3-glycidoxypropyltrimethoxysilane (GOPS) have been characterized by using angularly dependent X-ray photoelectron spectroscopy (XPS), time-of-flight secondary-ion mass spectrometry (ToF-SIMS), atomic force microscopy (AFM), scanning electron microscopy (SEM), and monochromatic and spectroscopic ellipsometry. XPS and ToF-SIMS data provided evidence of complete surface coverage by GOPS. Data from angularly resolved XPS and ellipsometry methods suggested that the GOPS films were of monolayer thickness. AFM and SEM data indicated the presence of films that consisted of nodules approximately 50-100 nm in diameter. Modeling suggested that the nodules may lead to a nanoscale structural morphology that might influence the hybridization kinetics and thermodynamics of immobilized oligonucleotides.

Electrochemical probe for on-chip type flow immunoassay: Immunoglobulin G labeled with ferrocenecarboaldehyde

Labeling of ferrocenecarboaldehyde (Fc-CHO) to immunoglobulin G (IgG) via formation of Schiff-base and its reduction was investigated for construction of an electrochemical probe for miniaturized amperometric flow immunoassay. Approximately eight molecules of Fc-CHO were labeled to IgG and the reversible redox property of ferrocene was observed. Labeling efficiency improved by over three times as compared to the conventional method using ferrocenemonocarboxylic acid (Fc-COOH). Also, binding affinity of IgG labeled with Fc-CHO to its antigen, IgE, was investigated by enzyme-linked immunosorbent assay (ELISA) and surface plasmon resonance assay. IgG labeled with Fc-CHO that retained eight ferrocene moiety showed sufficient binding affinity to its antigen and the current response obtained in the flow electrochemical detection system increased by 14-fold as compared with IgG labeled with Fc-COOH when applying the potential of 390 mV vs. Ag/AgCl. The minimum detectable concentration of IgG labeled with Fc-CHO was 0.06 microM. IgG labeled with Fc-CHO demonstrate biochemical and electrochemical properties that are useful for electrochemical immunosensors.

Bioelectrocatalytic signaling from immunosensors with back-filling immobilization of glucose oxidase on biorecognition surfaces

We report a novel method of electrochemical signaling from antigen-antibody interactions at immunoelectrodes with bioelectrocatalyzed enzymatic signal amplification. For the immunosensing surface construction, a poly(amidoamine) G4-dendrimer was employed not only as a building block for the electrode surface modification but also as a matrix for ligand functionalization. As a model biorecognition reaction, the dinitrophenyl (DNP) antigen-functionalized electrode was fabricated and an anti-DNP antibody was used. Glucose oxidase (GOX) was chosen to amplify electrochemical signal by enzymatic catalysis. The signal amplification strategy introduced in this study is based on the back-filling immobilization of biocatalytic enzyme to the immunosensor surface, circumventing the use of an enzyme-labeled antibody. The non-labeled native antibody was biospecifically bound to the immobilized ligand, and the activated enzyme (periodate-treated GOX) reacted and "back-filled" the remaining surface amine groups on the dendrimer layer by an imine formation reaction. From the bioelectrocatalyzed signal registration with the immobilized GOX, the surface density of biospecifically bound antibody could be estimated. The DNP functionalization reaction was optimized to facilitate the antibody recognition and signaling reactions, and approximately 6% displacement of surface amine to DNP was found to be an optimum. From quartz crystal microbalance measurement, immunosensing reaction timing and the surface inertness to the nonspecific biomolecular binding were tested. By changing the surface functionalization level of DNP in the calibration experiments, immunosensors exhibited different dynamic detection ranges and limits of detection, supporting the capability of parameters modulation for the immunosensors. For the anti-DNP antibody assay, the fabricated immunosensor having 65% functionalization ratio exhibited the linear detection range of 10(-4) to 0.1 g/L protein and a limit of detection around 2 x 10(-5) g/L.