VO 2 /V 2 O 5 :Ag Nanostructures on a DVD as Photoelectrochemical Sensors

Laser-induced graphene hybrid photoelectrode for enhanced photoelectrochemical detection of glucose

The combination of an electrocatalyst with a semiconductor light absorber is of great importance to increase the efficiency of photoelectrochemical (PEC) glucose detection. Here, in situ and synchronous fabrication of a Ni-based electrocatalyst (NiEC) and CdS semiconductor in laser-induced graphene (LIG) on indium-tin oxide glass is demonstrated via a one-step laser-induced solid phase transition. A series of component and structural characterization experiments suggest that the laser-induced NiEC uniformly disperses in the hybrid nanocomposite and exists mainly in the Ni⁰ and NiO states. Moreover, both electrochemical and PEC investigations confirm that the as-prepared hybrid photoelectrode exhibits excellent photoelectrocatalytic ability towards glucose, which is not only attributed to the strong synergistic interaction between CdS and NiEC, but also benefited from the high conductivity as well as 3D macroporous configuration of the simultaneously formed LIG, providing the key factor to achieve sensitive non-enzymatic PEC glucose sensors. Therefore, the laser-induced hybrid photoelectrode is then applied to the PEC detection of glucose, and a low detection limit of 0.4 μM is obtained with good stability, reproducibility, and selectivity. This study provides a promising paradigm for the facile and binder-free fabrication of an electrocatalyst-semiconductor-graphene hybrid photoelectrode, which will find potential applications in sensitive PEC biosensing for a broad range of analytes.

Disposable electrodes from waste materials and renewable sources for (bio)electroanalytical applications

The numerous advantages of disposable and screen-printed electrodes (SPEs) particularly in terms of portability, sensibility, sensitivity and low-cost led to the massive application of these electroanalytical devices. To limit the electronic waste and recover precious materials, new recycling processes were developed together with alternative SPEs fabrication procedures based on renewable, biocompatible sources or waste materials, such as paper, agricultural byproducts or spent batteries. The increased interest in the use of eco-friendly materials for electronics has given rise to a new generation of highly performing green modifiers. From paper based electrodes to disposable electrodes obtained from CD/DVD, in the last decades considerable efforts were devoted to reuse and recycle in the field of electrochemistry. Here an overview of recycled and recyclable disposable electrodes, sustainable electrode modifiers and alternative fabrication processes is proposed aiming to provide meaningful examples to redesign the world of disposable electrodes.

Ti3C2/Cu2O heterostructure based signal-off photoelectrochemical sensor for high sensitivity detection of glucose

Photoelectrochemical (PEC) sensing has emerged as a simple and practical method for the analysis and detection, its separated optical signal and detection electrical signal give it the advantages of reduced background noise and outstanding sensitivity. Here, we synthesized a Ti₃C₂/Cu₂O composite through simple oil bath heating process, whose excellent PEC performance and sensitive photoelectric response to glucose make it a propitious substitution to glucose oxidase. On this basis, we construct a PEC non-enzymatic sensor based on the Ti₃C₂/Cu₂O heterostructure for the detection of glucose. Under the optimal conditions, the photocurrent of Ti₃C₂/Cu₂O is linear with the logarithm value of glucose concentration in the wide range of 0.5 nM to 0.5 mM with a detection limit of 0.17 nM. Furthermore, the successful detection of glucose in standard samples and human serum by the proposed Ti₃C₂/Cu₂O based PEC non-enzymatic sensor demonstrates the application prospect of heterostructure material in PEC sensor, which provides a new thought for the design and construction of PEC non-enzymatic sensing platform.

Efficient photocatalysis with graphene oxide/Ag/Ag2S–TiO2 nanocomposites under visible light irradiation

The photocatalytic reaction efficiency of GO/Ag/Ag₂S–TiO₂ nanorod arrays is 600% higher than that of a pure TiO₂ sample under visible light.

Ag-Vanadates/GO Nanocomposites by Aerosol-Assisted Spray Pyrolysis: Preparation and Structural and Electrochemical Characterization of a Versatile Material

In this article, we describe the deposition by aerosol-assisted spray pyrolysis of different types of silver vanadate nanocomposites with and without graphene oxide (GO) on different substrates (carbon paper (CP) and fluorine-doped tin oxide (FTO)). When deposited on CP, different amounts of GO were added to the Ag and V precursor solution to study the effect of GO on the physicochemical properties of the resulting Ag-vanadate. It is shown that the addition of GO leads mainly to the formation of nanoparticles of the Ag2V4O11 phase, whereas Ag2V4O11 and Ag3VO4 are obtained without the addition of GO. The morphology and chemical properties of the composites were determined by scanning and transmission electron microscopies, X-ray diffraction, X-ray photoemission spectroscopy, and UV-visible and Raman spectroscopies. In addition, the photoelectrochemical (PEC) properties of such composites were studied by CV, linear sweep voltammetry, and electrochemical impedance spectroscopy. The ideal Ag x VO y and GO ratio was optimized for obtaining higher photocurrent values and a good stability. The results showed that the presence of GO improves the electrical conductivity of the catalyst layer as well as the electron injection from the oxide to the electrode surface. The deposition of pure Ag2V4O11 on FTO does not lead to samples with stable PEC performances. Samples grown on CP supports showed an efficient electrochemical detection of small amounts of ethylenediamine in water solution.