Investigation of stress shielding around the Stryker Omnifit and Exeter periprosthetic hip implants using an irreversible thermodynamic-based model

Stem Alignment With the Tapered Wedge Cementless Stem "Accolade II" Does Not Affect Bone Mineral Density Over 5 Years After Total Hip Arthroplasty

Background

This study aimed to investigate the relationship between 3-dimensional (3D) alignment and postoperative bone mineral density (BMD) changes with Accolade II tapered wedge stems, which have a different proximal shape from other tapered wedge stems, up to 5 years after primary total hip arthroplasty.

Methods

We retrospectively analyzed the hips of 89 patients who underwent total hip arthroplasty using the second-generation proximally coated cementless stem (Accolade II; Stryker Orthopedics, Mahwah, NJ) at our institution from 2014 to 2018 over a 5-year follow-up. We evaluated the relationship between stem alignment, measured using 3D-templating software, and BMD changes in the 7 Gruen zones and compared the data with those from a former study using other short taper-wedge stems.

Results

BMDs in zones 1 and 7 continued to decrease gradually every year after surgery, and BMD in zone 7 showed the largest decrease (21%) from baseline over 5 years. No correlation was found between stem alignment (varus/valgus, flexion/extension, and anteversion/retroversion) and changes in BMD in each zone over 5 years.

Conclusions

Our data showed no correlation between 3D stem alignment and changes in BMD in each Gruen zone over 5 years. This suggests that the Accolade II stem may fit better into any shape of the proximal medullary canal because of its unique characteristics.

The Use of Customized Three-Dimensionally Printed Mandible Prostheses with a Pressure-Reducing Device: A Finite Element Analysis in Different Chewing Positions, Biomechanical Testing, and In Vivo Animal Study Using Lanyu Pigs

Segmental bony defects of the mandible constitute a complete loss of the regional part of the mandible. Although several types of customized three-dimension-printed mandible prostheses (CMPs) have been developed, this technique has yet to be widely used. We used CMP with a pressure-reducing device (PRD) to investigate its clinical applicability. First, we used the finite element analysis (FEA). We designed four models of CMP (P1 to P4), and the result showed that CMP with posterior PRD deployment (P4 group) had the maximum total deformation in the protrusion and right excursion positions, and in clenching and left excursion positions, posterior screws had the minimum von Mises stress. Second, the P4 CMP-PRD was produced using LaserCUSING from titanium alloy (Ti-6Al-4V). The fracture test result revealed that the maximum static pressure that could be withstood was 189 N, and a fatigue test was conducted for 5,000,000 cycles. Third, animal study was conducted on five male 4-month-old Lanyu pigs. Four animals completed the experiment. Two animals had CMP exposure in the oral cavity, but there was no significant inflammation, and one animal had a rear wing fracture. According to a CT scan, the lingual cortex of the mandible crawled along the CMP surface, and a bony front-to-back connection was noted in one animal. A histological examination indicated that CMP was significantly less reactive than control materials (p = 0.0170). Adequate PRD deployment in CMP may solve a challenge associated with CMP, thus promoting its use in clinical practice.

Challenges in computational fluid dynamics applications for bone tissue engineering

Bone injuries or defects that require invasive surgical treatment are a serious clinical issue, particularly when it comes to treatment success and effectiveness. Accordingly, bone tissue engineering (BTE) has been researching the use of computational fluid dynamics (CFD) analysis tools to assist in designing optimal scaffolds that better promote bone growth and repair. This paper aims to offer a comprehensive review of recent studies that use CFD analysis in BTE. The mechanical and fluidic properties of a given scaffold are coupled to each other via the scaffold architecture, meaning an optimization of one may negatively affect the other. For example, designs that improve scaffold permeability normally result in a decreased average wall shear stress. Linked with these findings, it appears there are very few studies in this area that state a specific application for their scaffolds and those that do are focused on in vitro bioreactor environments. Finally, this review also demonstrates a scarcity of studies that combine CFD with optimization methods to improve scaffold design. This highlights an important direction of research for the development of the next generation of BTE scaffolds.

Multi-objective design optimization of dental implant geometrical parameters

In-silico investigations are becoming an integral part of the development of novel biomedical devices, including dental implants. Using computer simulations can streamline the process by tuning different geometrical and structural features, emphasizing the osseointegration of the implant design a priori, leading to the optimal designs in preparation for in-vivo trails. This research aims to elucidate the interrelationship between 12 geometrical variables that holistically define the shape of the implant. The approach to achieve optimality hinged on coupling the finite element analysis results with the fractional factorial design method. The latter was used to determine the most influential variables during the screening process, followed by the parameter optimization process using the response surface method, regarding four different objectives, namely: bone-implant contact area, volume of trabecular bone dead cells, volume of cortical bone dead cells, and axial displacement. This resulted in reducing the number of virtual experiments and substantially decreasing the computational cost without compromising the accuracy of the solution. It was found that the optimized values improved the performance significantly. The validity of all models was verified by comparing optimized responses with simulation results. A sensitivity analysis was performed on all five optimized models to address the effect of friction coefficient on the implant-bone joint interaction. It was shown that the mechanical behavior of implant-bone would be independent in higher friction coefficients. The significance of this study is demonstrated in determining the most effective and optimized values of all possible geometrical parameters considering their singular or interactive effects.

Long-term results of the custom- made hip endoprostheses Evolution K® and Adaptiva®: A prospective cohort study

The aim of our study is to evaluate clinical long-term results and determine changes in periprosthetic bone density of the custom-made hip prostheses Evolution-K^® and Adaptiva^®. Periprosthetic bone density were evaluated by means of DEXA (LunariDXA- Prodigy^® bone densitometer) with a long-term follow-up of 16 (15-18) years (Evolution-K^®) in 24 patients and 13 (13-15) years (Adaptiva^®) in 41 patients. Evolution- K^® had a survival rate of 92% and yielded 79/100 points in Harris Hip Score, a mediocre result. Adaptiva^® had a survival rate of 99% and achieved a good score of 88/100 points. Bone density measurements demonstrated the greatest loss of bone density in the proximal regions of interest (ROI) for both prosthesis types (Evolution-K^®: -25.8% ROI 1, -40.3% ROI 7; -8.3% ROI 2, -10.4% ROI 6; Adaptiva^®: -29.8% ROI 7, -6.8% ROI 6, +14.3% ROI 3, +3.1% ROI 4). Adaptiva^® yielded a good clinical result as compared to Evolution-K^® with only average clinical results. Both prostheses clearly showed signs of “stress shielding”. Here, the Adaptiva^® achieved reduced bone density loss as compared to the Evolution-K^®.

3D-printed poly(Ɛ-caprolactone) scaffold with gradient mechanical properties according to force distribution in the mandible for mandibular bone tissue engineering

In bone tissue engineering, prediction of forces induced to the native bone during normal functioning is important in the design, fabrication, and integration of a scaffold with the host. The aim of this study was to customize the mechanical properties of a layer-by-layer 3D-printed poly(ϵ-caprolactone) (PCL) scaffold estimated by finite element (FE) modeling in order to match the requirements of the defect, to prevent mechanical failure, and ensure optimal integration with the surrounding tissue. Forces and torques induced on the mandibular symphysis during jaw opening and closing were predicted by FE modeling. Based on the predicted forces, homogeneous-structured PCL scaffolds with 3 different void sizes (0.3, 0.6, and 0.9 mm) were designed and 3D-printed using an extrusion based 3D-bioprinter. In addition, 2 gradient-structured scaffolds were designed and 3D-printed. The first gradient scaffold contained 2 regions (0.3 mm and 0.6 mm void size in the upper and lower half, respectively), whereas the second gradient scaffold contained 3 regions (void sizes of 0.3, 0.6, and 0.9 mm in the upper, middle and lower third, respectively). Scaffolds were tested for their compressive and tensile strength in the upper and lower halves. The actual void size of the homogeneous scaffolds with designed void size of 0.3, 0.6, and 0.9 mm was 0.20, 0.59, and 0.95 mm, respectively. FE modeling showed that during opening and closing of the jaw, the highest force induced on the symphysis was a compressive force in the transverse direction. The compressive force was induced throughout the symphyseal line and reduced from top (362.5 N, compressive force) to bottom (107.5 N, tensile force) of the symphysis. Compressive and tensile strength of homogeneous scaffolds decreased by 1.4-fold to 3-fold with increasing scaffold void size. Both gradient scaffolds had higher compressive strength in the upper half (2 region-gradient scaffold: 4.9 MPa; 3 region-gradient scaffold: 4.1 MPa) compared with the lower half (2 region-gradient scaffold: 2.5 MPa; 3 region-gradient scaffold: 2.7 MPa) of the scaffold. 3D-printed PCL scaffolds had higher compressive strength in the scaffold layer-by-layer building direction compared with the side direction, and a very low tensile strength in the scaffold layer-by-layer building direction. Fluid shear stress and fluid pressure distribution in the gradient scaffolds were more homogeneous than in the 0.3 mm void size scaffold and similar to the 0.6 mm and 0.9 mm void size scaffolds. In conclusion, these data show that the mechanical properties of 3D-printed PCL scaffolds can be tailored based on the predicted forces on the mandibular symphysis. These 3D-printed PCL scaffolds had different mechanical properties in scaffold building direction compared with the side direction, which should be taken into account when placing the scaffold in the defect site. Our findings might have implications for improved performance and integration of scaffolds with native tissue.

Effects of femoral bone defect morphology on initial polished tapered stem stability in massive defect model: a biomechanical study

Background

Good outcomes have been reported in revision total hip replacement with massive segmental defects using impaction bone grafting with circumferential metal meshes. However, the morphology of defects that require a mesh is poorly defined. The purpose of this study was to evaluate the effects of a variety of segmental defects on load transmission to the proximal femur under both axial and rotational loads.

Methods

Initial stability of the Exeter stem was investigated in a composite bone model using three medial bone defect morphologies: Long (length 5 cm × width 2 cm), Short (2.5 cm × 2 cm), Square (3.2 cm × 3.2 cm), Square with mesh (3.2 cm × 3.2 cm defect covered with metal mesh), and with no defect as control. Specimens (5 per group) were axially loaded and internally rotated up to 20° or to failure. Strain distributions of the femora were measured using a strain gauge.

Results

All Square group specimens failed while rotation was increasing. In the other four groups, failure was not observed in any specimens. Mean torsional stiffness in the Long (4.4 ± 0.3 Nm/deg.) and Square groups (4.3 ± 0.3 Nm/deg.) was significantly smaller than in the Control group (4.8 ± 0.3 Nm/deg.). In the medio-cranial region, the magnitude of the maximum principal strain in the Square group (1176.4 ± 100.9) was significantly the largest (Control, 373.2 ± 129.5, p < 0.001; Long, 883.7 ± 153.3, p = 0.027; Short, 434.5 ± 196.8, p < 0.001; Square with mesh, 256.9 ± 100.8, p < 0.001). Torsional stiffness, and both maximum and minimum principal strains in the Short group showed no difference compared to the Control group in any region.

Conclusions

Bone defect morphology greatly affected initial stem stability and load transmission. If defect morphology is not wide and the distal end is above the lower end of the lesser trochanter, it may be acceptable to fill the bone defect region with bone cement. However, this procedure is not acceptable for defects extending distally below the lower end of the lesser trochanter or defects 3 cm or more in width.

Fixation Release and the Bone Bandaid: A New Bone Fixation Device Paradigm

The current gold standard of care for mandibular segmental defeat reconstruction is the use of Ti-6Al-4V immobilization hardware and fibular double barrel graft. This method is often successful immediately at restoring mandible function, however the highly stiff fixation hardware causes stress shielding of the grafted bone and stress concentration in the fixation device over time which can lead to fixation device failure and revision surgery. The purpose of reconstructive surgery could be to create normal stress trajectories in the mandible following engraftment. We investigate the use of a two stage mechanism which separates the immobilization/healing and regenerative phases of mandibular segmental defect treatment. The device includes the use of a very stiff, Ti-6Al-4V, releasable mechanism which assures bone healing. Therefore it could be released once the reconstructed boney tissue and any of its ligamentous attachments have completely healed. Underneath the released Ti-6Al-4V plate would be a pre-loaded nitinol (NiTi) wire-frame apparatus that facilitates the normal stress-strain trajectory through the engrafted bone after the graft is healed in place and the Ti-6Al-4V fixation device has been released. Due to the use of NiTi wires forming a netting that connects vascularized bone and possibly bone chips, bone grafts are also more likely to be incorporate rather than to resorb. We first evaluated a healthy adult mandible during normal mastication to obtain the normal stress-strain distribution. Then, we developed the finite element (FE) model of the mandibular reconstruction (in the M1-3 region) with the proposed fixation device during the healing (locked state) and post-healing (released state) periods. To recreate normal stress trajectory in the reconstructed mandible, we applied the Response Surface Methodology (RMS) to optimize the Bone Bandaid geometry (i.e., wire diameters and location). The results demonstrate that the proposed mechanism immobilizes the grafted bone in the locked state properly since the maximum resultant gap (21.54 micron) between the graft and host mandible surfaces are in the safe region (less than 300 micron). By considering the von Mises criteria for failure, FE analysis together with experimental studies (i.e., compressive and tensile testing on the inferior and superior fixation devices, respectively) confirm that the proposed fixation devices do not fail, showing safety factor of at least 10.3. Based on the Response Surface Methodology (RSM) technique, the optimal parameter values for the wires are achieved (0.65 mm and 1 mm for the superior and inferior wires, respectively) and the required level of preload on each wire are calculated (369.8 N and 229 N for the inferior and superior wires, respectively). The FE results for stress distribution on the reconstructed mandible during the released state closely match that of a healthy mandible.

Mid- and long-term results of femoral component revision using the cement-in-cement technique: Average 10.8-year follow-up study

BACKGROUND

Few reports are available on the long-term outcomes of femoral component revision by using the cement-in-cement technique. We report the mid- and long-term results of femoral component revision in total hip arthroplasty using the cement-in-cement technique.

METHODS

Between April 1996 and June 2009, 62 consecutive total hip arthroplasties with femoral component revision were performed in 57 patients by using the cement-in-cement technique. We retrospectively reviewed the cases with a follow-up period of at least five years. Three patients died, and two were lost to follow-up. Thus, 52 patients (57 hips), comprising 51 women and one man, were followed for average 10.8 years.

RESULTS

The mean Japanese Orthopaedic Association hip score improved from 57.6 points (range, 28-95 points) preoperatively to 79.8 points (range, 52-98 points) at one year postoperatively and to 77.4 points (range, 59-96 points) at the final follow up. Three revisions of the femoral component were necessary. One of the causes for the revision was a periprosthetic infection that occurred 20 months postoperatively. Another was aseptic loosening that occurred 99 months postoperatively and required revision of the acetabular component. The well-fixed femoral component was revised using the cement-in-cement technique at time of the acetabular revision. The third case was aseptic loosening of the femoral component that occurred 84 months postoperatively. The five-, 10-, and 15-year survival rates for the femoral re-revision due to any reason were 98.4%, 94.0%, and 94.0%, respectively.

CONCLUSION

Use of the cement-in-cement technique for revision total hip arthroplasty resulted in good mid- and long-term radiological and clinical outcomes.

Effect of bisphosphonates in preventing femoral periprosthetic bone resorption after primary cementless total hip arthroplasty: a meta-analysis

Background

Bone loss leading to aseptic loosening of the prosthesis and periprosthetic fracture is a mode of failure in cementless total hip arthroplasty (THA). The aim of this meta-analysis was to evaluate the effect of bisphosphonates in preventing femoral periprosthetic bone resorption following primary cementless THA zone by zone.

Method

Clinical randomized controlled trials concerning bisphosphonates application after primary cementless THA published up to October 2014 were retrieved from PubMed, Cochrane library, and Embase databases. The methodological quality of the included studies was assessed by the Physiotherapy Evidence Database (PEDro) scale. Data analysis was performed using StataSE12.0.

Results

Ten randomized controlled trials involving a total of 502 patients were assessed; the bisphosphonates group included 256 patients and the control group included 246 patients. The meta-analysis showed that the bone mineral density (BMD) of most femoral periprosthetic zones in bisphosphonates group was significantly higher than that in the control group at 3 months postoperatively except zone 5 with no significant difference. At 6 and 12 months, the BMD of bisphosphonates group was much higher than that in control group except zone 5, which showed no statistical difference. The BMD of bisphosphonates group was persistently higher than control group in zone 6 and 7 at 5 years postoperatively, while the other zones had no significant difference. Both serum bone alkaline phosphatase and urinary type I collagen N-telopeptide were significantly suppressed by bisphosphonates at 3, 6, and 12 months.

Conclusion

Bisphosphonates seem to decrease early femoral periprosthetic bone resorption after primary cementless THA. Drug efficacy was found to be long-standing in the main load-bearing zones.

Periprosthetic fracture torque for short versus standard cemented hip stems: an experimental in vitro study

In an attempt to preserve proximal femoral bone stock and achieve a better fit in smaller femora, especially in the Asian population, several new shorter stem designs have become available. We investigated the torque to periprosthetic femoral fracture of the Exeter short stem compared with the conventional length Exeter stem in a Sawbone model. Forty-two stems; 21 shorter and 21 conventional stems both with three different offsets were cemented in a composite Sawbone model and torqued to fracture. Results showed that Sawbone femurs break at a statistically significantly lower torque to failure with a shorter compared to conventional-length Exeter stem of the same offset. Both standard and short-stem designs are safe to use as the torque to failure is 7-10 times that seen in activities of daily living.

Cell-based approaches to the engineering of vascularized bone tissue

This review summarizes recent efforts to create vascularized bone tissue in vitro and in vivo through the use of cell-based therapy approaches. The treatment of large and recalcitrant bone wounds is a serious clinical problem, and in the United States approximately 10% of all fractures are complicated by delayed union or non-union. Treatment approaches with the use of growth factor and gene delivery have shown some promise, but results are variable and clinical complications have arisen. Cell-based therapies offer the potential to recapitulate key components of the bone-healing cascade, which involves concomitant regeneration of vasculature and new bone tissue. For this reason, osteogenic and vasculogenic cell types have been combined in co-cultures to capitalize on the function of each cell type and to promote heterotypic interactions. Experiments in both two-dimensional and three-dimensional systems have provided insight into the mechanisms by which osteogenic and vasculogenic cells interact to form vascularized bone, and these approaches have been translated to ectopic and orthotopic models in small-animal studies. The knowledge generated by these studies will inform and facilitate the next generation of pre-clinical studies, which are needed to move cell-based orthopaedic repair strategies into the clinic. The science and application of cytotherapy for repair of large and ischemic bone defects is developing rapidly and promises to provide new treatment methods for these challenging clinical problems.