Crystallization of progesterone for pulmonary drug delivery

Spray Dried Progesterone Formulations for Carrier Free Dry Powder Inhalation

Low oral absorption and extensive first pass metabolism of progesterone is reported for many oral formulations which warrants investigation into other routes of administration. It is the aim of this study to investigate the generation of inhaled formulations of progesterone though a spray drying approach with a focus on how spray drying impacts the physicochemical properties of progesterone. Formulations of progesterone with L-leucine and hydroxypropyl methylcellulose acetate succinate (HPMCAS) are reported to this aim. X-ray diffraction, spectroscopy and thermal analysis were used to characterise these formulations and confirmed that progesterone crystallises as the Form II polymorph during spray drying regardless of the solvent used. The resultant formulations showed higher aqueous solubility than progesterone Form I starting material and the addition of HPMCAS was shown to temporarily enable a supersaturated state. Thermal analysis was used to show that the Form II polymorph was sensitive to transformation to Form I during heating. The addition of L-leucine to the formulations reduced the temperature for the polymorphic transformation by ∼10 °C. However, when HPMCAS was added to the formulation, the Form II polymorph was prevented from transforming to the Form I polymorph. Cascade impaction was used to determine the aerosol performance of the spray dried powders and showed promising lung deposition profiles (mass median aerodynamic diameter 5 µm) with significant variation depending on the organic solvent used and the ratio of organic to aqueous phase in the feedstock. However, further optimisation of formulations was required to direct more progesterone into the alveolar regions. The addition of HPMCAS was seen to increase the alveolar deposition and therefore formed a formulation with a lower fine particle fraction and mass median aerodynamic diameter. The most suitable formulation for inhalation was formed from a 50:50 acetone:water destockck and showed an ED, FPF and FPD of 81.7%, 44.5% and 7.3 mg respectively. Therefore, HPMCAS is suggested as a suitable excipient to increase solubility, prevent polymorphic transformation and improve inhalation properties of spray dried progesterone formulations. This study highlights the use of spray drying to form inhalable progesterone powders with higher solubility which may broaden the application of this medicine.

An expert opinion on respiratory delivery of high dose powders for lung infections

INTRODUCTION

High dose powder inhalation is evolving as an important approach to to treat lung infections. It is important to its identify applications, consider the factors affecting high dose powder delivery, and assess the effect of high dose drugs in patients.

AREA COVERED

Both current and pipeline high dose inhalers and their applications have been summarized. Challenges and opportunities to high dose delivery have been highlighted after reviewing formulation techniques in the context of factors affecting aerosolization, devices, and patient factors.

EXPERT OPINION

High dose inhaled delivery of antimicrobials is an innovative way to increase treatment efficacy of respiratory infections, tackle drug resistance, and the scarcity of new antimicrobials. The high dose inhaled technology also has potential for systemic action; however, innovations in formulation strategies and devices are required to realize its full potential. Advances in formulation strategies include the use of excipients or the engineering of particles to decrease the cohesive property of microparticles and their packing density. Similarly, selection of a synergistic drug instead of an excipient can be considered to increase aerosolization and stability. Device development focused on improving dispersion and loading capacity is also important, and modification of existing devices for high dose delivery can also be considered.

Preparation of Ibuprofen Microparticles by Antisolvent Precipitation Crystallization Technique: Characterization, Formulation, and In Vitro Performance

This study demonstrates the preparation and characterization of ibuprofen (IBP) microparticles with some excipients by a controlled crystallization technique with improved dissolution performance. Using the optimum concentrations pluronic F127, hydroxypropyl methyl cellulose, D-mannitol, and l-leucine in aqueous ethanol, the IBP microparticles were prepared. The dissolution tests were performed in phosphate buffer saline using a United States Pharmacopoeia dissolution tester at 37°C. The Raman spectroscopy was used to investigate the interactions and distribution of the IBP with the additives in the microcrystals. The prepared IBP microparticles showed higher dissolution compared to that of the smaller sized original IBP particles. The Raman data revealed that the excipients with a large number of hydroxyl groups distributed around the IBP particle in the crystal enhanced the dissolution of the drug by increasing the drug-solvent interaction presumably through hydrogen bonding. The Raman mapping technique gave an insight into the enhanced dissolution behavior of the prepared IBP microparticles, and such information will be useful for developing pharmaceutical formulations of hydrophobic drugs. The controlled crystallization was a useful technique to prepare complex crystals of IBP microparticles along with other additives to achieve the enhanced dissolution profile.

A review on recent technologies for the manufacture of pulmonary drugs

This review discusses recent developments in the manufacture of inhalable dry powder formulations. Pulmonary drugs have distinct advantages compared with other drug administration routes. However, requirements of drugs properties complicate the manufacture. Control over crystallization to make particles with the desired properties in a single step is often infeasible, which calls for micronization techniques. Although spray drying produces particles in the desired size range, a stable solid state may not be attainable. Supercritical fluids may be used as a solvent or antisolvent, which significantly reduces solvent waste. Future directions include application areas such as biopharmaceuticals for dry powder inhalers and new processing strategies to improve the control over particle formation such as continuous manufacturing with in-line process analytical technologies.