1
|
Kaushik R, Mani A, Ganapathi S, Pillai VV, Jayakumar K, S H. Clinical outcomes of bileaflet St. Jude Medical and tilting disc TTK Chitra mechanical heart valve prosthesis: A comparative study. J Card Surg 2022; 37:2367-2374. [PMID: 35577768 DOI: 10.1111/jocs.16605] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/15/2022] [Revised: 03/27/2022] [Accepted: 04/01/2022] [Indexed: 11/26/2022]
Abstract
BACKGROUND Comparative data on the clinical outcomes of TTK Chitra mechanical heart valve prosthesis (CHVP), an indigenously developed low-cost tilting disc valve and commonly used bileaflet valve, the St. Jude medical (SJM) prosthesis are sparse. METHODS We conducted a retrospective follow-up study of consecutive patients undergoing mitral (MVR) and aortic valve replacement (AVR) with SJM or CHVP mechanical prostheses over a 6-year period at our institution. RESULTS Seven hundred and thirty-five patients who underwent isolated MVR (n = 510) or AVR (n = 225) were included in the study. Patients with CHVP were younger and belonged to a lower socioeconomic class. The study cohort was followed-up for 2836 patient-years (SJM: 1865.1, CHVP: 971.0). All-cause mortality (p = 0.894), valve-related mortality (p = 0.681), prosthetic valve thrombosis (p = 0.155), embolism (p = 0.210), hemorrhage (p = 0.959) and infective endocarditis (IE, p = 0.084) were similar between both valve on follow-up. Estimated event free survival was 2302 ± 1 days in SJM as compared to 2484 ± 65 days in CHVP group (p = 0.393). Valve type was not an independent predictor of adverse events after adjusting for baseline data, time in therapeutic range and aspirin use. Subgroup analysis of patients who underwent MVR and AVR showed similar functional improvement and outcomes, except for a higher incidence of IE with SJM at the aortic position (p = 0.041). CONCLUSION The indigenously developed, low-cost CHVP has comparable midterm clinical performance as SJM in aortic or mitral positions.
Collapse
Affiliation(s)
- Rupesh Kaushik
- Department of Cardiology, Sreechitra Tirunal Institute for Medical Sciences and Technology, Thiruvananthapuram, Kerala, India
| | - Avinash Mani
- Department of Cardiology, Sreechitra Tirunal Institute for Medical Sciences and Technology, Thiruvananthapuram, Kerala, India
| | - Sanjay Ganapathi
- Department of Cardiology, Sreechitra Tirunal Institute for Medical Sciences and Technology, Thiruvananthapuram, Kerala, India
| | - Vivek V Pillai
- Department of Cardiothoracic Surgery, Sreechitra Tirunal Institute for Medical Sciences and Technology, Thiruvananthapuram, Kerala, India
| | - Karunakaran Jayakumar
- Department of Cardiothoracic Surgery, Sreechitra Tirunal Institute for Medical Sciences and Technology, Thiruvananthapuram, Kerala, India
| | - Harikrishnan S
- Department of Cardiology, Sreechitra Tirunal Institute for Medical Sciences and Technology, Thiruvananthapuram, Kerala, India
| |
Collapse
|
2
|
Qian JY, Gao ZX, Hou CW, Jin ZJ. A comprehensive review of cavitation in valves: mechanical heart valves and control valves. Biodes Manuf 2019. [DOI: 10.1007/s42242-019-00040-z] [Citation(s) in RCA: 16] [Impact Index Per Article: 3.2] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/26/2022]
|
3
|
Babu S, Sreedhar R, Gadhinglajkar SV, Dash PK, Sukesan S, Pillai V, Panicker VT, Shriram LP, Aggarwal N. Intraoperative Transesophageal and Postoperative Transthoracic Echocardiographic Evaluation of a Mechanical Heart Valve Prosthesis Implanted at Aortic Position. J Cardiothorac Vasc Anesth 2017; 32:782-789. [PMID: 29217244 DOI: 10.1053/j.jvca.2017.09.001] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 07/22/2017] [Indexed: 11/11/2022]
Abstract
OBJECTIVE The aims of this study were to evaluate the intraoperative transesophageal echocardiographic (iTEE) characteristics and Doppler flow profile of aortic Chitra heart valve prosthesis (CHVP) under stable hemodynamic and loading conditions, and to compare and correlate the iTEE data with the postoperative transthoracic echocardiography (TTE) data obtained at 48 hours (TTE1) and 3 months (TTE2) after the surgery. DESIGN Prospective, observational study. SETTING University-level tertiary referral hospital. PARTICIPANTS Forty patients between 18 years and 65 years of age undergoing elective aortic valve replacement (AVR) using CHVP during the period January 2015 to August 2016. INTERVENTIONS After obtaining permission from institutional ethics committee, 40 patients undergoing elective AVR were studied prospectively. The iTEE examination was performed in the pre-cardiopulmonary bypass (CPB) and post-CPB period in all the study subjects. CHVP was subjected to iTEE two-dimensional (2D) echo, color Doppler, and spectral Doppler evaluation under stable hemodynamic and loading condition in the post-CPB period after the administration of protamine. The CHVP were re-evaluated using TTE in all the patients 48 hours after the surgery (TTE1) and 3 months after the surgery (TTE2). The iTEE and postoperative TTE Doppler values were compared and correlated. MEASUREMENTS AND MAIN RESULTS The CHVP could be imaged adequately and interrogated with Doppler in all the patients. None of the patients had restriction of occluder mobility or unstable seating of the valve. The intraoperative flow dependent (peak velocity [PV] and mean pressure gradient [MPG]) and less flow dependent (Doppler velocity index, acceleration time, acceleration time/ejection time, effective orifice area [EOA] and indexed EOA) Doppler parameters of CHVP were measured as per the American Society of Echocardiography recommendations. The PV and MPG of CHVP measured by iTEE showed no statistical difference (p > 0.05) and were in limits of agreement when compared with TTE1 and TTE2 data. CONCLUSION The iTEE features of CHVP were found compliant with the criteria set by the ASE defining normal functioning of an aortic valve prosthesis. The iTEE Doppler parameters obtained under stable loading conditions strongly predicted the postoperative values of Doppler parameters on TTE examination. The iTEE Doppler values can be used as the reference values for the postoperative follow up studies.
Collapse
Affiliation(s)
- Saravana Babu
- Department of Anesthesia, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| | - Rupa Sreedhar
- Department of Anesthesia, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India.
| | - Shrinivas V Gadhinglajkar
- Department of Anesthesia, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| | - Prasanta Kumar Dash
- Department of Anesthesia, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| | - Subin Sukesan
- Department of Anesthesia, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| | - Vivek Pillai
- Department of Cardiothoracic and Vascular Surgery, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| | - Varghese T Panicker
- Department of Cardiothoracic and Vascular Surgery, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| | - Lovhale Pravin Shriram
- Department of Anesthesia, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| | - Neelam Aggarwal
- Department of Anesthesia, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum, India
| |
Collapse
|
4
|
Review of numerical methods for simulation of mechanical heart valves and the potential for blood clotting. Med Biol Eng Comput 2017; 55:1519-1548. [DOI: 10.1007/s11517-017-1688-9] [Citation(s) in RCA: 22] [Impact Index Per Article: 3.1] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/10/2017] [Accepted: 07/10/2017] [Indexed: 11/26/2022]
|
5
|
Casillas-Ituarte NN, Cruz CHB, Lins RD, DiBartola AC, Howard J, Liang X, Höök M, Viana IFT, Sierra-Hernández MR, Lower SK. Amino acid polymorphisms in the fibronectin-binding repeats of fibronectin-binding protein A affect bond strength and fibronectin conformation. J Biol Chem 2017; 292:8797-8810. [PMID: 28400484 DOI: 10.1074/jbc.m117.786012] [Citation(s) in RCA: 15] [Impact Index Per Article: 2.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/14/2017] [Revised: 04/08/2017] [Indexed: 11/06/2022] Open
Abstract
The Staphylococcus aureus cell surface contains cell wall-anchored proteins such as fibronectin-binding protein A (FnBPA) that bind to host ligands (e.g. fibronectin; Fn) present in the extracellular matrix of tissue or coatings on cardiac implants. Recent clinical studies have found a correlation between cardiovascular infections caused by S. aureus and nonsynonymous SNPs in FnBPA. Atomic force microscopy (AFM), surface plasmon resonance (SPR), and molecular simulations were used to investigate interactions between Fn and each of eight 20-mer peptide variants containing amino acids Ala, Asn, Gln, His, Ile, and Lys at positions equivalent to 782 and/or 786 in Fn-binding repeat-9 of FnBPA. Experimentally measured bond lifetimes (1/koff) and dissociation constants (Kd = koff/kon), determined by mechanically dissociating the Fn·peptide complex at loading rates relevant to the cardiovascular system, varied from the lowest-affinity H782A/K786A peptide (0.011 s, 747 μm) to the highest-affinity H782Q/K786N peptide (0.192 s, 15.7 μm). These atomic force microscopy results tracked remarkably well to metadynamics simulations in which peptide detachment was defined solely by the free-energy landscape. Simulations and SPR experiments suggested that an Fn conformational change may enhance the stability of the binding complex for peptides with K786I or H782Q/K786I (Kdapp = 0.2-0.5 μm, as determined by SPR) compared with the lowest-affinity double-alanine peptide (Kdapp = 3.8 μm). Together, these findings demonstrate that amino acid substitutions in Fn-binding repeat-9 can significantly affect bond strength and influence the conformation of Fn upon binding. They provide a mechanistic explanation for the observation of nonsynonymous SNPs in fnbA among clinical isolates of S. aureus that cause endovascular infections.
Collapse
Affiliation(s)
| | - Carlos H B Cruz
- the Aggeu Magalhães Institute, Oswaldo Cruz Foundation, Recife, PE, 50.740-465, Brazil, and
| | - Roberto D Lins
- the Aggeu Magalhães Institute, Oswaldo Cruz Foundation, Recife, PE, 50.740-465, Brazil, and
| | | | | | - Xiaowen Liang
- the Center for Infectious and Inflammatory Diseases, Institute of Biosciences and Technology, Texas A&M Health Science Center, Houston, Texas 77030
| | - Magnus Höök
- the Center for Infectious and Inflammatory Diseases, Institute of Biosciences and Technology, Texas A&M Health Science Center, Houston, Texas 77030
| | - Isabelle F T Viana
- the Aggeu Magalhães Institute, Oswaldo Cruz Foundation, Recife, PE, 50.740-465, Brazil, and
| | | | | |
Collapse
|
6
|
Annerel S, Claessens T, Degroote J, Segers P, Vierendeels J. Validation of a numerical FSI simulation of an aortic BMHV by in vitro PIV experiments. Med Eng Phys 2014; 36:1014-23. [PMID: 24924383 DOI: 10.1016/j.medengphy.2014.05.004] [Citation(s) in RCA: 11] [Impact Index Per Article: 1.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/04/2013] [Revised: 04/01/2014] [Accepted: 05/05/2014] [Indexed: 10/25/2022]
Abstract
In this paper, a validation of a recently developed fluid-structure interaction (FSI) coupling algorithm to simulate numerically the dynamics of an aortic bileaflet mechanical heart valve (BMHV) is performed. This validation is done by comparing the numerical simulation results with in vitro experiments. For the in vitro experiments, the leaflet kinematics and flow fields are obtained via the particle image velocimetry (PIV) technique. Subsequently, the same case is numerically simulated by the coupling algorithm and the resulting leaflet kinematics and flow fields are obtained. Finally, the results are compared, revealing great similarity in leaflet motion and flow fields between the numerical simulation and the experimental test. Therefore, it is concluded that the developed algorithm is able to capture very accurately all the major leaflet kinematics and dynamics and can be used to study and optimize the design of BMHVs.
Collapse
Affiliation(s)
- S Annerel
- Ghent University, Department of Flow, Heat and Combustion Mechanics, Sint-Pietersnieuwstraat 41, B-9000 Ghent, Belgium.
| | - T Claessens
- Ghent University, Department of Industrial Technology and Construction, Valentin Vaerwyckweg 1, B-9000 Ghent, Belgium.
| | - J Degroote
- Ghent University, Department of Flow, Heat and Combustion Mechanics, Sint-Pietersnieuwstraat 41, B-9000 Ghent, Belgium.
| | - P Segers
- Ghent University, iMinds Medical IT, IBiTech-bioMMeda, De Pintelaan 185, B-9000 Ghent, Belgium.
| | - J Vierendeels
- Ghent University, Department of Flow, Heat and Combustion Mechanics, Sint-Pietersnieuwstraat 41, B-9000 Ghent, Belgium.
| |
Collapse
|
7
|
Malhotra A, Pawar SR, Srivastava A, Yadav BS, Kaushal R, Sharma P, Songra M. Clinical and hemodynamic study of tilting disc heart valve: Single-center study. Asian Cardiovasc Thorac Ann 2014; 22:519-25. [PMID: 24646514 DOI: 10.1177/0218492313475640] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/15/2022]
Abstract
BACKGROUND The TTK Chitra heart valve has been developed and widely used in India. This study aimed to evaluate its hemodynamics, complications, and event-free survival in comparison with other commonly used prosthetic valves. The role of color Doppler echocardiography in the follow-up of patients with prosthetic valves was also studied. PATIENTS AND METHODS Two hundred patients underwent 249 valve replacements (122 mitral, 29 aortic, 49 both). Total follow-up was 451 patient-years. RESULTS There were 18 late deaths (3.98% ± 0.92% per patient-year). One mitral valve replacement patient (0.36% ± 0.36% per patient-year) developed valve thrombosis. Two aortic valve replacement patients (2.74% ± 1.91% per patient-year), 2 double-valve replacement patients (1.95% ± 1.36% per patient-year) and 3 mitral valve replacement patients (1.08% ± 0.62% per patient-year) developed embolic complications. Freedom from all valve related mortality and morbidity at 4 years was 86% ± 4% for mitral valve replacement, 56% ± 10% for double-valve replacement, and 89% ± 6% for aortic valve replacement. The average peak gradient, mean gradient, and average peak velocity for the aortic and mitral positions were found to be comparable to those of other commonly used valves. CONCLUSION The performance of this valve in terms of hemodynamic complications, mortality, and morbidity is comparable to other valves in common use. Hemodynamic gradients are more reproducible than effective orifice area, hence more beneficial for follow-up.
Collapse
|
8
|
Abstract
Cavitation was first directly related to mechanical heart valves in the mid 1980s after a series of valve failures observed with the Edwards-Duromedics valve. The damages observed indicated that cavitation could be responsible. Later, several in vitro studies visualized the bubble formation and collapse of cavitation at mechanical heart valves. It was suggested that cavitation could also cause damage to the formed elements of blood and thereby enhance the risk of thromboembolic complications seen in mechanical heart valve patients. Therefore, an applicable technique for in vivo detection of cavitation is required. This article reviews techniques developed for in vivo detection of cavitation and suggests focus for future studies.
Collapse
Affiliation(s)
- Peter Johansen
- Department of Cardiothoracic and Vascular Surgery, Research Unit, Aarhus University Hospital, Skejby Sygehus, Brendstrupgaardsvej, 8200 Aarhus N, Denmark.
| |
Collapse
|
9
|
Forleo M, Dasi LP. Effect of hypertension on the closing dynamics and Lagrangian blood damage index measure of the b-datum regurgitant jet in a bileaflet mechanical heart valve. Ann Biomed Eng 2013; 42:110-22. [PMID: 23975384 DOI: 10.1007/s10439-013-0896-1] [Citation(s) in RCA: 19] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/01/2013] [Accepted: 08/14/2013] [Indexed: 11/27/2022]
Abstract
We hypothesize that the formation of the closing vortex and subsequent b-datum regurgitation jet in bileaflet mechanical heart valves is governed by the magnitude of the driving mean aortic pressure (MAP), and that this sensitivity does impact the blood damage index (BDI) corresponding to platelet activation and lysis. High spatial resolution time resolved (1 kHz) as well as phase locked particle image velocimetry techniques captured the dynamic leaflet closure and regurgitation jet of a model 25 mm St. Jude Medical BMHV. Cell trajectories were estimated using Lagrangian particle tracking analysis while the leaflet kinematics was quantified by tracking the leaflet tip-position throughout closure. The non-principal as well as principal shear stress loading histories along each cell trajectory revealed BDI for platelet activation and lysis as a function of cell initial position, release time-point, and blood pressure. Results show that the leaflet closing time reduces by roughly 10 ms, in response to an increase in MAP by 40 mmHg. We report that higher MAP leads to a stronger b-datum vortex and jet formation. Platelet activation BDI lowers with a higher MAP due to reduction in exposure times despite an increase in principal shear stress experienced. Platelet lysis BDI however increases with higher MAP. Maximum BDI may occur for cells initially in the b-datum zone during the onset of leaflet closure. Our results provide a better understanding of BDI of the regurgitant b-datum jet and sheds light on the potential importance of blood damage testing under hypertensive conditions.
Collapse
Affiliation(s)
- Marcio Forleo
- School of Biomedical Engineering, Colorado State University, Fort Collins, CO, USA
| | | |
Collapse
|
10
|
Aortic Root Compliance Influences Hemolysis in Mechanical Heart Valve Prostheses: An In-Vitro Study. Int J Artif Organs 2012; 35:495-502. [DOI: 10.5301/ijao.5000108] [Citation(s) in RCA: 8] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 03/01/2012] [Indexed: 11/20/2022]
Abstract
Mechanical heart valve prostheses are known to activate coagulation and cause hemolysis. Both are particularly dependent on the leaflet dynamics, which in turn depends on the flow field in the aortic root influenced by the aortic root geometry and its compliance. Compliance reduction of large vessels occurs in aging patients, both in those who have atherosclerotic diseases and those who do not. In this study we investigated the correlation between hemolysis and the compliance of the proximal aorta in a novel, pulsatile in vitro blood tester using porcine blood. Two mechanical heart valves, the St Jude Medical (SJM) bileaflet valve and a trileaflet valve prototype (Triflo) were tested for hemolysis under physiological conditions (120/80 mm Hg, 4.5 l/min, 70 bpm) and using two different tester setups: with a stiff aorta and with a compliant aorta. Valve dynamics were subsequently analyzed via high-speed videos. In the tests with the Triflo valve, the free plasma hemoglobin increased by 13.4 mg/dl for the flexible and by 19.3 mg/dl for the stiff setup during the 3-hour test. The FFT spectra and closing speed showed slight differences for both setups. Free plasma hemoglobin for the SJM valve was up by 22.2 mg/dl in the flexible and 42.7 mg/dl in the stiff setup. Cavitation induced by the higher closing speed might be responsible for this, which is also indicated by the sound spectrum elevation above 16 kHz.
Collapse
|
11
|
Transient, Three-Dimensional Flow Field Simulation through a Mechanical, Trileaflet Heart Valve Prosthesis. ASAIO J 2011; 57:278-82. [DOI: 10.1097/mat.0b013e318222849c] [Citation(s) in RCA: 12] [Impact Index Per Article: 0.9] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/25/2022] Open
|
12
|
Cavitation phenomena in mechanical heart valves: studied by using a physical impinging rod system. Ann Biomed Eng 2010; 38:3162-72. [PMID: 20490686 DOI: 10.1007/s10439-010-0070-y] [Citation(s) in RCA: 9] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/11/2010] [Accepted: 05/07/2010] [Indexed: 10/19/2022]
Abstract
When studying mechanical heart valve cavitation, a physical model allows direct flow field and pressure measurements that are difficult to perform with actual valves, as well as separate testing of water hammer and squeeze flow effects. Movable rods of 5 and 10 mm diameter impinged same-sized stationary rods to simulate squeeze flow. A 24 mm piston within a tube simulated water hammer. Adding a 5 mm stationary rod within the tube generated both effects simultaneously. Charged-coupled device (CCD) laser displacement sensors, strobe lighting technique, laser Doppler velocimetry (LDV), particle image velocimetry (PIV) and high fidelity piezoelectric pressure transducers measured impact velocities, cavitation images, squeeze flow velocities, vortices, and pressure changes at impact, respectively. The movable rods created cavitation at critical impact velocities of 1.6 and 1.2 m/s; squeeze flow velocities were 2.8 and 4.64 m/s. The isolated water hammer created cavitation at 1.3 m/s piston speed. The combined piston and stationary rod created cavitation at an impact speed of 0.9 m/s and squeeze flow of 3.2 m/s. These results show squeeze flow alone caused cavitation, notably at lower impact velocity as contact area increased. Water hammer alone also caused cavitation with faster displacement. Both effects together were additive. The pressure change at the vortex center was only 150 mmHg, which cannot generate the magnitude of pressure drop required for cavitation bubble formation. Cavitation occurred at 3-5 m/s squeeze flow, significantly different from the 14 m/s derived by Bernoulli's equation; the temporal acceleration of unsteady flow requires further study.
Collapse
|
13
|
Numerical analysis on the hemodynamics and leaflet dynamics in a bileaflet mechanical heart valve using a fluid-structure interaction method. ASAIO J 2009; 55:428-37. [PMID: 19730001 DOI: 10.1097/mat.0b013e3181b58f98] [Citation(s) in RCA: 22] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/25/2022] Open
Abstract
Bileaflet mechanical heart valves (BMHVs) are widely implanted to replace diseased heart valves but still suffer from complications such as hemolysis and platelet activation. These complications are closely related to both flow characteristics through the valves and leaflet dynamics. In this study, a fluid-structure interaction (FSI) simulation is performed to investigate the characteristics of physiological flow interacting with moving leaflets in a BMHV. The present FSI model uses both a finite volume computational fluid dynamics code and a finite element structure dynamics code to solve the governing equations for fluid flow and leaflet dynamics. In addition, a structural analysis is performed with the forces acting on the leaflet surfaces. From the analysis, detailed flow information and leaflet behavior are quantified for a cardiac cycle. The results show that the present FSI model performs well at predicting the overall flow patterns interacting with the moving leaflets and leaflet behavior in the BMHV.
Collapse
|
14
|
Cardiovascular cavitation. Med Eng Phys 2009; 31:742-51. [DOI: 10.1016/j.medengphy.2009.03.007] [Citation(s) in RCA: 25] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/19/2008] [Revised: 03/12/2009] [Accepted: 03/15/2009] [Indexed: 12/22/2022]
|
15
|
Jazi AM, Rahimzadeh H. Waveform analysis of cavitation in a globe valve. ULTRASONICS 2009; 49:577-582. [PMID: 19328513 DOI: 10.1016/j.ultras.2009.02.004] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/21/2008] [Revised: 02/04/2009] [Accepted: 02/04/2009] [Indexed: 05/27/2023]
Abstract
Cavitation is a dynamic phenomenon occurring in fluid flows, where the local static pressure is lower than the saturated vapor pressure at working temperature. The growth and collapse of cavitation bubbles leads to corrosion and pitting of metal surfaces. Considering the fact that erosion by cavitation is still one of the current problems, it is important to detect the initiation, fully developed point of cavitation and to analyze its characteristics. In this research, an attempt is made to study acoustic waveform of cavitation in the globe valve. The waveform is transformed by Fast Fourier Transform and its important parameters such as amplitude, energy, frequency and so on are analyzed.
Collapse
Affiliation(s)
- A Masjedian Jazi
- Fluid Mechanics Lab., Department of Mechanical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Tehran, Iran
| | | |
Collapse
|
16
|
Shalaby S, Chandran K, Burg K. Soft Tissue Replacements. Biomaterials 2007. [DOI: 10.1201/9780849378898.ch8] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/11/2022]
|
17
|
Zhang P, Yeo JH, Hwang NHC. Development of Squeeze Flow in Mechanical Heart Valve: A Particle Image Velocimetry Investigation. ASAIO J 2006; 52:391-7. [PMID: 16883118 DOI: 10.1097/01.mat.0000225267.87767.68] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/27/2022] Open
Abstract
Fluid between the reducing flow channel of the valve occluder and the orifice wall tends to be squeezed out of the flow channel, causing a high-speed flow. The squeeze flow is accompanied by a sharp local pressure drop, which may result in potential cavitation phenomenon in a mechanical heart valve (MHV). Limited experimental investigation has been conducted into the flow physics of this squeeze flow phenomenon, which is likely to be the origin of MHV cavitation. We used a pulsatile test loop simulating physiologic flow conditions and an actual-size transparent MHV model for flow visualization. A digital particle image velocimetry (DPIV) system incorporated with a microscope was applied to observe flow within a narrowing channel. A triggering mechanism was designed so that the DPIV system could be timed to capture images when the valve occluder was near its closing position. A series of images within the channel from 1.4 to 0.1 mm were captured. As the gap between the tip of the valve occluder and orifice wall becomes narrower, evidence of high-speed jet flow becomes more apparent. When the flow channel is reduced to around 0.1 mm, flow velocity of up to 2 m/s was noted. A sudden increase in high-speed jet flow causes a corresponding reduction in local pressure, and is a likely source for potential cavitation.
Collapse
Affiliation(s)
- Pei Zhang
- School of Mechanical & Automation Engineering, Shanghai Institute of Technology, Shanghai, China
| | | | | |
Collapse
|
18
|
Herbertson LH, Reddy V, Manning KB, Welz JP, Fontaine AA, Deutsch S. Wavelet transforms in the analysis of mechanical heart valve cavitation. J Biomech Eng 2006; 128:217-22. [PMID: 16524333 DOI: 10.1115/1.2165694] [Citation(s) in RCA: 14] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/08/2022]
Abstract
Cavitation is known to cause blood element damage and may introduce gaseous emboli into the cerebral circulation, increasing the patient's risk of stroke. Discovering methods to reduce the intensity of cavitation induced by mechanical heart valves (MHVs) has long been an area of interest. A novel approach for analyzing MHV cavitation is presented. A wavelet denoising method is explored because currently used analytical techniques fail to suitably unmask the cavitation signal from other valve closing sounds and noise detected with a hydrophone. Wavelet functions are used to denoise the cavitation signal during MHV closure and rebound. The wavelet technique is applied to the signal produced by closure of a 29-mm Medtronic-Hall MHV in degassed water with a gas content of 5 ppm. Valve closing dynamics are investigated under loading conditions of 500, 2500, and 4500 mm Hg/s. The results display a marked improvement in the quantity and quality of information that can be extracted from acoustic cavitation signals using the wavelet technique compared to conventional analytical techniques. Time and frequency data indicate the likelihood and characteristics of cavitation formation under specified conditions. Using this wavelet technique we observe an improved signal-to-noise ratio, an enhanced time-dependent aspect, and the potential to minimize valve closing sounds, which disguise individual cavitation events. The overall goal of this work is to eventually link specific valves with characteristic waveforms or distinct types of cavitation, thus promoting improved valve designs.
Collapse
Affiliation(s)
- Luke H Herbertson
- Department of Bioengineering, The Pennsylvania State University, University Park, PA 16802, USA
| | | | | | | | | | | |
Collapse
|
19
|
Wu C, Herman BA, Retta SM, Grossman LW, Liu JS, Hwang NHC. On the Closing Sounds of a Mechanical Heart Valve. Ann Biomed Eng 2005; 33:743-50. [PMID: 16078614 DOI: 10.1007/s10439-005-3237-1] [Citation(s) in RCA: 9] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/25/2022]
Abstract
In the 1994 Replacement Heart Valve Guidance of the U.S. Food and Drug Administration (FDA), in-vitro testing is required to evaluate the potential for cavitation damage of a mechanical heart valve (MHV). To fulfill this requirement, the stroboscopic high-speed imaging method is commonly used to visualize cavitation bubbles at the instant of valve closure. The procedure is expensive; it is also limited because not every cavitation event is detected, thus leaving the possibility of missing the whole cavitation process. As an alternative, some researchers have suggested an acoustic cavitation-detection method, based on the observation that cavitation noise has a broadband spectrum. In practice, however, it is difficult to differentiate between cavitation noise and the valve closing sound, which may also contain high-frequency components. In the present study, the frequency characteristics of the closing sound in air of a Björk-Shiley Convexo-Concave (BSCC) valve are investigated. The occluder closing speed is used as a control parameter, which is measured via a laser sweeping technique. It is found that for the BSCC valve tested, the distribution of the sound energy over its frequency domain changes at different valve closing speeds, but the cut-off frequency remains unchanged at 123.32 +/- 6.12 kHz. The resonant frequencies of the occluder are also identified from the valve closing sound.
Collapse
Affiliation(s)
- Changfu Wu
- Center for Applied Stochastics Research, College of Engineering, Florida Atlantic University, 777 Glades Road, Boca Raton, FL 33431, USA.
| | | | | | | | | | | |
Collapse
|
20
|
Maines BH, Brennen CE. Lumped Parameter Model for Computing the Minimum Pressure During Mechanical Heart Valve Closure. J Biomech Eng 2005; 127:648-55. [PMID: 16121535 DOI: 10.1115/1.1934164] [Citation(s) in RCA: 10] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/08/2022]
Abstract
The cavitation inception threshold of mechanical heart valves has been shown to be highly variable. This is in part due to the random distribution of the initial and final conditions that characterize leaflet closure. While numerous hypotheses exist explaining the mechanisms of inception, no consistent scaling laws have been developed to describe this phenomenon due to the complex nature of these dynamic conditions. Thus in order to isolate and assess the impact of these varied conditions and mechanisms on inception, a system of ordinary differential equations is developed to describe each system component and solved numerically to predict the minimum pressure generated during valve closure. In addition, an experiment was conducted in a mock circulatory loop using an optically transparent size 29 bileaflet valve over a range of conditions to calibrate and validate this model under physiological conditions. High-speed video and high-response pressure measurements were obtained simultaneously to characterize the relationship between the valve motion, fluid motion, and negative pressure transients during closure. The simulation model was calibrated using data from a single closure cycle and then compared to other experimental flow conditions and to results found in the literature. The simulation showed good agreement with the closing dynamics and with the minimum pressure trends in the current experiment. Additionally, the simulation suggests that the variability observed experimentally (when using dP∕dt alone as the primary measure of cavitation inception) is predictable. Overall, results from the current form of this lumped parameter model indicate that it is a good engineering assessment tool.
Collapse
Affiliation(s)
- Brant H Maines
- CarboMedics, A Sorin Group Company, Austin, Texas 78752, USA
| | | |
Collapse
|
21
|
Manning KB, Przybysz TM, Fontaine AA, Tarbell JM, Deutsch S. Near Field Flow Characteristics of the Bjork-Shiley Monostrut Valve in a Modified Single Shot Valve Chamber. ASAIO J 2005; 51:133-8. [PMID: 15839436 DOI: 10.1097/01.mat.0000153496.01522.e4] [Citation(s) in RCA: 12] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/26/2022] Open
Abstract
In certain mechanical heart valves, cavitation has been shown to develop during closure and rebound, leading to valve damage, blood damage, and strokes. Whereas it is uncertain what causes mechanical heart valve related strokes, some evidence suggests that stable bubbles may be the culprits. Previous work has indicated that vortex cavitation may contribute to stable bubble growth. Therefore, in an effort to understand the vortex cavitation, laser Doppler velocimetry data are collected in a plane parallel to and 3 mm away from the major orifice during closure and rebound of a Bjork-Shiley Monostrut mechanical heart valve. A modified single shot chamber is used that incorporates a more realistic near valve geometry than those used in previous studies. The results show the formation of a vortex during closure, which intensifies during rebound and dissipates during the final closing cycle. A regurgitant jet with mean velocities up to 3 m/s through the clearance gap of the valve provides energy to the vortex. During the final closing cycle, the vortex breaks up into asymmetrical, small scale flow patterns. This study provides further evidence that stable bubble formation may stem from the intense vortex cavitation occurring during valve closure and rebound.
Collapse
Affiliation(s)
- Keefe B Manning
- Department of Bioengineering, The Pennsylvania State University, University Park 16802, USA
| | | | | | | | | |
Collapse
|
22
|
Abstract
Several aspects of mechanical heart valve cavitation, in particular of "severe" vapor cavitation, have been investigated in order to describe the phenomenon of cavitation itself and to classify various mechanical heart valves with respect to their tendency to cavitation. Furthermore, following the results of the measurements, a model for determination of time-dependent physical properties and dynamics of cavitation bubbles, such as size, pressure and temperature was developed. In order to classify the cavitation tendency of mechanical valves, a pulsatile hydraulic-driven circularly mock loop was used. Besides measurements of the relevant hemodynamic parameters, the leaflet velocities of the valves were also determined. In addition, numerous high-resolution pressure measurements, in particular the pressure drops necessary for the initiation of cavitation (local atrial pressure drop), were performed. For the investigation of bubble dynamics, a second pulsatile electro-magnetically-driven tester was used. The influence of density, viscosity and temperature of the fluid on the onset of cavitation was investigated. Cavitation events were recorded with a digital high-speed video camera (up to 40,500 frames/sec) for all investigated heart valves and under different conditions. A critical local upstream pressure drop (located within the model atrium after valve closure) of 450 mmHg was found for all valves as well as a valve specific correlation between left ventricular pressure gradient and local upstream pressure drop. Also, a valve dependent correlation between left ventricular pressure gradient and the local upstream pressure drop was provided. Finally, valve specific parameters were found to predict the cavitation tendency for a specific heart valve. The implementation of a suitable theoretical model allowed conclusions on bubble physics. High pressures (up to 800 bar) and temperatures (up to 1,300 degrees C) at bubble collapse have been determined. The influence of fluid parameters such as density, viscosity and temperature on the onset of cavitation is negligible within physiological range. Critical regions for cavitation for all mechanical heart valves were detected. All mechanical heart valves investigated show cavitation under different conditions (dp/dt) associated with high pressures and temperatures at bubble collapse. Cavitation bubble occurrence depends on valve design and location.
Collapse
Affiliation(s)
- M J Eichler
- Helmholtz-Institute for Biomedical Engineering, RWTH Aachen, Aachen-Germany.
| | | |
Collapse
|
23
|
Lu PC, Liu JS, Huang RH, Lo CW, Lai HC, Hwang NHC. The Closing Behavior of Mechanical Aortic Heart Valve Prostheses. ASAIO J 2004; 50:294-300. [PMID: 15307536 DOI: 10.1097/01.mat.0000130678.59655.c0] [Citation(s) in RCA: 22] [Impact Index Per Article: 1.1] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/25/2022] Open
Abstract
Mechanical artificial heart valves rely on reverse flow to close their leaflets. This mechanism creates regurgitation and water hammer effects that may form cavitations, damage blood cells, and cause thromboembolism. This study analyzes closing mechanisms of monoleaflet (Medtronic Hall 27), bileaflet (Carbo-Medics 27; St. Jude Medical 27; Duromedics 29), and trileaflet valves in a circulatory mock loop, including an aortic root with three sinuses. Downstream flow field velocity was measured via digital particle image velocimetry (DPIV). A high speed camera (PIVCAM 10-30 CCD video camera) tracked leaflet movement at 1000 frames/s. All valves open in 40-50 msec, but monoleaflet and bileaflet valves close in much less time (< 35 msec) than the trileaflet valve (>75 msec). During acceleration phase of systole, the monoleaflet forms a major and minor flow, the bileaflet has three jet flows, and the trileaflet produces a single central flow like physiologic valves. In deceleration phase, the aortic sinus vortices hinder monoleaflet and bileaflet valve closure until reverse flows and high negative transvalvular pressure push the leaflets rapidly for a hard closure. Conversely, the vortices help close the trileaflet valve more softly, probably causing less damage, lessening back flow, and providing a washing effect that may prevent thrombosis formation.
Collapse
Affiliation(s)
- Po-Chien Lu
- Department of Water Resources and Environmental Engineering, Tamkang University, Tamsui, Taipei, Taiwan
| | | | | | | | | | | |
Collapse
|
24
|
Manning KB, Kini V, Fontaine AA, Deutsch S, Tarbell JM. Regurgitant flow field characteristics of the St. Jude bileaflet mechanical heart valve under physiologic pulsatile flow using particle image velocimetry. Artif Organs 2003; 27:840-6. [PMID: 12940907 DOI: 10.1046/j.1525-1594.2003.07194.x] [Citation(s) in RCA: 56] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/20/2022]
Abstract
The regurgitant flow fields of clinically used mechanical heart valves have been traditionally studied in vitro using flow visualization, ultrasound techniques, and laser Doppler velocimetry under steady and pulsatile flow. Detailed investigation of the forward and regurgitant flow fields of these valves can elucidate a valve's propensity for blood element damage, thrombus formation, or cavitation. Advances in particle image velocimetry (PIV) have allowed its use in the study of the flow fields of prosthetic valves. Unlike other flow field diagnostic systems, recent work using PIV has been able to relate particular regurgitant flow field characteristics of the Bjork-Shiley Monostrut valve to a propensity for cavitation. In this study, the regurgitant flow field of the St. Jude Medical bileaflet mechanical heart valve was assessed using PIV under physiologic pulsatile flow conditions. Data collected at selected time points prior to and after valve closure demonstrated the typical regurgitant jet flow patterns associated with the St. Jude valve, and indicated the formation of a strong regurgitant jet, in the B-datum plane, along with twin vortices near the leaflets. Estimated ensemble-average viscous shear rates suggested little potential for hemolysis when the hinge jets collided. However, the vortex motion near the occluder tips potentially provides a low-pressure environment for cavitation.
Collapse
Affiliation(s)
- Keefe B Manning
- Department of Bioengineering, The Pennsylvania State University, University Park, PA 16802, USA
| | | | | | | | | |
Collapse
|
25
|
Lim WL, Chew YT, Low HT, Foo WL. Cavitation phenomena in mechanical heart valves: the role of squeeze flow velocity and contact area on cavitation initiation between two impinging rods. J Biomech 2003; 36:1269-80. [PMID: 12893035 DOI: 10.1016/s0021-9290(03)00161-1] [Citation(s) in RCA: 22] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/27/2022]
Abstract
In this study, the closing dynamics of two impinging rods were experimentally analyzed to simulate the cavitation phenomena associated with mechanical heart valve closure. The purpose of this study was to investigate the cavitation phenomena with respect to squeeze flow between two impinging surfaces and the parameter that influences cavitation inception. High-speed flow imaging was employed to visualize and identify regions of cavitation. The images obtained favored squeeze flow as an important mechanism in cavitation inception. A correlation study of the effects of impact velocities, contact areas and squeeze flow velocity on cavitation inception showed that increasing impact velocities results in an increase in the risk of cavitation. It was also shown that for similar impact velocities, regions near the point of impact were found to cavitate later for those with smaller contact areas. It was found that the decrease in contact areas and squeeze flow velocities would delay the onset and reduce the intensity of cavitation. It is also interesting to note that the squeeze flow velocity alone does not provide an indication if cavitation inception will occur. This is corroborated by the wide range of published critical squeeze flow velocity required for cavitation inception. It should be noted that the temporal acceleration of fluid, often neglected in the literature, can also play an important role on cavitation inception for unsteady flow phenomenon. This is especially true in mechanical heart valves, where for the same leaflet closing velocity, valves with a seat stop were observed to cavitate earlier. Based on these results, important inferences may be made to the design of mechanical heart valves with regards to cavitation inception.
Collapse
Affiliation(s)
- W L Lim
- Department of Mechanical Engineering, Faculty of Engineering, 9 Engineering Drive 1, National University of Singapore, 117576, Singapore, Singapore.
| | | | | | | |
Collapse
|
26
|
|
27
|
Abstract
A computational fluid dynamics model for the analysis of the bileaflet mechanical heart valve closure process is presented. The objective of the study is to demonstrate the ability of the numerical model to simulate the leaflet motion during the closing phase in order to investigate the closure fluid dynamics and to evaluate the effect of alterations in the leaflet tip geometry. The model has been applied to six different combinations of the leaflet tip geometry and the gap width between the leaflet tip and the housing. The results show that the negative pressure quickly develops on the atrial side of the leaflet tip. The pressure becomes more negative as the leaflet closure progresses and the lowest pressure is reached before the leaflet comes to a stop in the closed position. The flow dynamics at the instant of valve closure is strongly dependent on the leaflet velocity during the closing phase. Decrease of the tip velocity by a factor of three in the last four degrees of leaflet motion leads to a 50% reduction in the negative pressure magnitude.
Collapse
Affiliation(s)
- Yong G Lai
- IIHR-Hydroscience and Engineering, The University of Iowa, Iowa City, IA 52242-1527, USA
| | | | | |
Collapse
|
28
|
Bacáková L, Walachová K, Svorcík V, Hnatowicz V. Adhesion and proliferation of rat vascular smooth muscle cells (VSMC) on polyethylene implanted with O+ and C+ ions. JOURNAL OF BIOMATERIALS SCIENCE. POLYMER EDITION 2002; 12:817-34. [PMID: 11587043 DOI: 10.1163/156856201750411684] [Citation(s) in RCA: 33] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/19/2022]
Abstract
Polyethylene was implanted with 30-keV oxygen (PE/O+) or 23-keV carbon ions (PE/C+) at 10(13) to 5 x 10(15) ions cm(-2) doses in order to improve the adhesion of vascular smooth muscle cell (VSMC) to the polymer surface in vitro because of its oxidation and carbon-enrichment. The concentration of -CO- groups in the PE/O+ and PE/C+ samples increased only up to doses of 3 x 10(14) and 10(15) ions cm(-2), respectively, and then declined. At the same time, the concentration of these groups, measured at a dose of 3 x 10(14) ions cm(-2), was higher in PE/O+ than in PE/C+ samples. Similarly, the number of initially-adhering rat VSMC (24 h after seeding) increased only up to a dose of 3 x 10(13) and 10(15) ions cm(-2) on PE/O+ and PE/C+ samples, respectively. In addition, between doses of 10(13) and 10(14) ions cm(-2), this number was about two to three times higher on PE/O+ samples. On the other hand, the surface wettability increased proportionally to the implanted ion dose, especially above a dose of 10(14) ions cm(-2). Thus, the number of initially-adhered cells appeared to be positively correlated with the amount of the oxygen group present at the polymer surface rather than with the surface wettability. The higher cell adhesion was accompanied by adsorption of fluorescent dye-conjugated collagen IV in larger amounts. The highest numbers of initially-adhered cells were usually associated with the lowest rates of subsequent proliferation (measured by the doubling time, BrdU labelling and M
Collapse
Affiliation(s)
- L Bacáková
- Institute of Physiology, Academy of Sciences of the Czech Republic, Prague.
| | | | | | | |
Collapse
|
29
|
Kini V, Bachmann C, Fontaine A, Deutsch S, Tarbell JM. Integrating particle image velocimetry and laser Doppler velocimetry measurements of the regurgitant flow field past mechanical heart valves. Artif Organs 2001; 25:136-45. [PMID: 11251479 DOI: 10.1046/j.1525-1594.2001.025002136.x] [Citation(s) in RCA: 22] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/20/2022]
Abstract
This study investigates the transient regurgitant flow downstream of a prosthetic heart valve using both laser Doppler velocimetry (LDV) and particle image velocimetry (PIV). Until now, LDV has been the more commonly used tool in investigating the flow characteristics associated with mechanical heart valves. The LDV technique allows point-by-point velocity measurements and provides enough information about the temporal variations in the flow. The main drawback of this technique is the time consuming nature of the data acquisition process in order to assess an entire flow field area. The PIV technique, on the other hand, allows measurement of the entire flow field in space in a plane at a given instant. In this study, PIV with spatial resolution of 0 (1 mm) and LDV with a temporal resolution of 0 (1 ms) were used to measure the regurgitant flow proximal to the Björk-Shiley monostrut (BSM) valve in the mitral position. With PIV, the ability to measure 2 velocity components over an entire plane simultaneously provides a very different insight into the flow field compared to a more traditional point-to-point technique like LDV. In this study, a picture of the effects of occluder motion on the fluid flow in the atrial chamber is interpreted using an integration of PIV and LDV measurements. Specifically, fluid velocities in excess of 3.0 m/s were recorded in the pressure-driven jet during valve closure, and a 1.5 m/s sustained regurgitant jet was observed on the minor orifice side. Additionally, the effects of the impact and subsequent rebound of the occluder on the flow also were clearly recorded in spatial and temporal detail by the PIV and LDV measurements, respectively. The PIV results provide a visually intuitive way of interpreting the flow while the LDV data explore the temporal variations and trends in detail. This analysis is an integrated flow description of the effects of valve closure and leakage on the pulsatile regurgitation flow field past a tilting-disc mechanical heart valve (MHV). It further reinforces the hypothesis that the planar flow visualization techniques, when integrated with traditional point-to point techniques, provide significantly more insight into the complex pulsatile flow past MHVs.
Collapse
Affiliation(s)
- V Kini
- Bioengineering Program; Applied Research Laboratory, Pennsylvania State University, University Park, Pennsylvania 16802, USA
| | | | | | | | | |
Collapse
|
30
|
|
31
|
Avrahami I, Rosenfeld M, Einav S, Eichler M, Reul H. Can vortices in the flow across mechanical heart valves contribute to cavitation? Med Biol Eng Comput 2000; 38:93-7. [PMID: 10829397 DOI: 10.1007/bf02344695] [Citation(s) in RCA: 25] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/24/2022]
Abstract
Cavitation in mechanical heart valves is traditionally attributed to the hammer effect and to squeeze and clearance flow occurring at the moment of valve closure. In the present study, an additional factor is considered--the contribution of vortex flow. Using a computational fluid dynamics analysis of a 2D model of a tilting disk mitral valve, we demonstrate that vortices may form in the vicinity of the inflow side of the valve. These vortices roll up from shear layers emanating from the valve tips during regurgitation. A significant decrease in the pressure at the centre of the vortices is found. The contribution of the vortex to the total pressure drop at the instant of closure is of the order of 70 mmHg. Adding this figure to the other pressure drop sources that reach 670 mmHg, it might be that this is the deciding factor that causes the drop in blood pressure below vapour pressure. The total pressure drop near the upper tip (750 mmHg) is larger than near the lower tip (670 mmHg), indicating a preferential location for cavitation inception, in agreement with existing experimental findings.
Collapse
Affiliation(s)
- I Avrahami
- Faculty of Engineering, Tel Aviv University, Israel
| | | | | | | | | |
Collapse
|