Computer simulations of comb-like macromolecules with responsive diblock copolymer side chains

Morphological Transitions in Micelles of Amphiphilic Bottlebrushes upon the Adsorption and Compression at the Liquid Interface

Densely grafted comb-like macromolecules (bottlebrushes) with alternating solvophobic and solvophilic side chains were studied in a selective solvent and at the liquid interface using mesoscopic computer simulations. The effects of backbone length and copolymer composition were considered. While self-assembly in solution revealed only spherical aggregates for all ar-chitectures studied, adsorption onto the liquid interface in particular cases resulted in morpho-logical changes, with worm-like aggregates or a continuous monolayer observed. In turn, the compression of macromolecules at the interface also leads to morphological transitions, includ-ing the formation of a mesh-like percolated structure. The obtained results may be useful for the preparation of solid nanoparticles of anisotropic shape or nanostructured ultra-thin copolymer films.

Effects of Residual Composition and Distribution on the Structural Characteristics of the Protein

The effect of ratio and consecutive number of hydrophobic residues in the repeating unit of protein chains was investigated by MD simulation. The modified off-lattice HNP model was applied in this study. The protein chains constituted by different HNP ratios or different numbers of consecutively hydrophobic residues with the same chain length were simulated under a broad temperature range. We concluded that the proteins with higher ratio or larger number of sequentially hydrophobic residues present more orientated and compact structure under a certain low temperature. It is attributed to the lower non-bonded potential energy between H-H residual pairs, especially more hydrophobic residues in a procession among the protein chain. Considering the microscopic structure of the protein, more residue contacts are achieved with the proteins with higher ratios and sequential H residues under the low temperature. Meanwhile, with the ratio and consecutive number of H residues increasing, the distribution of stem length showed a transition from exponential decline to unimodal and even multiple peaks, indicating the specific ordered structure formed. These results provide an insight into 3D structural properties of proteins from their residue sequences, which has a primary structure at molecular level and, ultimately, a practical possibility of applying in biotechnological applications.

Mesoscale Modeling of Agglomeration of Molecular Bottlebrushes: Focus on Conformations and Clustering Criteria

Using dissipative particle dynamics, we characterize dynamics of aggregation of molecular bottlebrushes in solvents of various qualities by tracking the number of clusters, the size of the largest cluster, and an average aggregation number. We focus on a low volume fraction of bottlebrushes in a range of solvents and probe three different cutoff criteria to identify bottlebrushes belonging to the same cluster. We demonstrate that the cutoff criteria which depend on both the coordination number and the length of the side chain allows one to correlate the agglomeration status with the structural characteristics of bottlebrushes in solvents of various qualities. We characterize conformational changes of the bottlebrush within the agglomerates with respect to those of an isolated bottlebrush in the same solvents. The characterization of bottlebrush conformations within the agglomerates is an important step in understanding the relationship between the bottlebrush architecture and material properties. An analysis of three distinct cutoff criteria to identify bottlebrushes belonging to the same cluster introduces a framework to identify both short-lived transient and long-lived agglomerates; the same approach could be further extended to characterize agglomerates of various macromolecules with complex architectures beyond the specific bottlebrush architecture considered herein.

Rigid-to-Flexible Transition in a Molecular Brush in a Good Solvent at a Semidilute Concentration

The structures of a molecular brush in a good solvent are investigated using synchrotron small-angle X-ray scattering in a wide range of concentrations. The brush under study, PiPOx₂₃₉-g-PnPrOx₁₄, features a relatively long poly(2-isopropenyl-2-oxazoline) (PiPOx) backbone and short poly(2-n-propyl-2-oxazoline) (PnPrOx) side chains. As a solvent, ethanol is used. By model fitting, the overall size and the persistence length as well as the interaction length and interaction strength are determined. At this, the interplay between form and structure factor is taken into account. The conformation of the molecular brush is traced upon increasing the solution concentration, and a rigid-to-flexible transition is found near the overlap concentration. Finally, the results of computer simulations of the molecular brush solutions confirm the experimental results.

Effects of temperature on chaotropic anion-induced shape transitions of star molecular bottlebrushes with heterografted poly(ethylene oxide) and poly(N,N-dialkylaminoethyl methacrylate) side chains in acidic water

This article reports a study of the effects of temperature on chaotropic anion (CA)-induced star-globule shape transitions in acidic water of three-arm star bottlebrushes composed of heterografted poly(ethylene oxide) (PEO) and either poly(2-(N,N-dimethylamino)ethyl methacrylate) (PDMAEMA) or poly(2-(N,N-diethylamino)ethyl methacrylate) (PDEAEMA) (the brushes denoted as SMB-11 and -22, respectively). The brush polymers were synthesized by grafting alkyne-end-functionalized PEO and PDMAEMA or PDEAEMA onto an azide-bearing three-arm star backbone polymer using the copper(i)-catalyzed alkyne-azide cycloaddition reaction. Six anions were studied for their effects on the conformations of SMB-11 and -22 in acidic water: super CAs [Fe(CN)6]3- and [Fe(CN)6]4-, moderate CAs PF6- and ClO4-, weak CA I-, and for comparison, kosmotropic anion SO42-. At 25 °C, the addition of super and moderate CAs induced shape transitions of SMB-11 and -22 in pH 4.50 water from a starlike to a collapsed globular state stabilized by PEO side chains, which was driven by the ion pairing of protonated tertiary amine groups with CAs and the chaotropic effect. The shape changes occurred at much lower salt concentrations for super CAs than moderate CAs. Upon heating from near room temperature to 70 °C, the super CA-collapsed brushes remained in the globular state, whereas the moderate CA-collapsed brushes underwent reversible globule-to-star shape transitions. The transition temperature increased with increasing salt concentration and was found to be higher for SMB-22 at the same salt concentration, presumably caused by the chaotropic effect. In contrast, I- and SO42- had small effects on the conformations of SMB-11 and -22 at 25 °C in the studied salt concentration range, and only small and gradual size variations were observed upon heating to 70 °C. The results reported here may have potential uses in the design of stimuli-responsive systems for substance encapsulation and release.

Shape-Changing Bottlebrush Polymers

Bottlebrush polymers (BBPs), composed of relatively short polymeric side chains densely grafted on a polymer backbone, exhibit many unique characteristics and hold promise for a variety of applications. This Perspective focuses on environmentally induced shape-changing behavior of BBPs at interface and in solution, particularly worm/star-globule shape transitions. While BBPs with a single type of homopolymer or random copolymer side chains have been shown to undergo pronounced worm-to-globule shape changes in response to external stimuli, the collapsed brushes are unstable and prone to aggregation. By introducing a second, solvophilic polymer into the side chains, either as a distinct type of side chain or as the outer block of block copolymer side chains, the collapsed brushes not only are stabilized but also create unimolecular micellar nanostructures, which can be used for, e.g., encapsulation and delivery of substances. The current challenges in the design, synthesis, and characterization of stimuli-responsive shape-changing BBPs are discussed.