In situ synthesis of g-C3N4/TiO2 heterojunction nanocomposites as a highly active photocatalyst for the degradation of Orange II under visible light irradiation

Surfactant-Modified CdS/CdCO3 Composite Photocatalyst Morphology Enhances Visible-Light-Driven Cr(VI) Reduction Performance

The surfactant modification of catalyst morphology is considered as an effective method to improve photocatalytic performance. In this work, the visible-light-driven composite photocatalyst was obtained by growing CdS nanoparticles in the cubic crystal structure of CdCO₃, which, after surfactant modification, led to the formation of CdCO₃ elliptical spheres. This reasonable composite-structure-modification design effectively increased the specific surface area, fully exposing the catalytic-activity check point. Cd²⁺ from CdCO₃ can enter the CdS crystal structure to generate lattice distortion and form hole traps, which productively promoted the separation and transfer of CdS photogenerated electron-hole pairs. The prepared 5-CdS/CdCO₃@SDS exhibited excellent Cr(VI) photocatalytic activity with a reduction efficiency of 86.9% within 30 min, and the reduction rate was 0.0675 min^-1, which was 15.57 and 14.46 times that of CdS and CdCO₃, respectively. Finally, the main active substances during the reduction process, the photogenerated charge transfer pathways related to heterojunctions and the catalytic mechanism were proposed and analyzed.

Photocatalytic Activity of TiO2/g-C3N4 Nanocomposites for Removal of Monochlorophenols from Water

This research employed g-C₃N₄ nanosheets in the hydrothermal synthesis of TiO₂/g-C₃N₄ hybrid photocatalysts. The TiO₂/g-C₃N₄ heterojunctions, well-dispersed TiO₂ nanoparticles on the g-C₃N₄ nanosheets, are effective photocatalysts for the degradation of monochlorophenols (MCPs: 2-CP, 3-CP, and 4-CP) which are prominent water contaminants. The removal efficiency of 2-CP and 4-CP reached 87% and 64%, respectively, after treatment of 25 ppm CP solutions with the photocatalyst (40TiO₂/g-C₃N₄, 1 g/L) and irradiation with UV-Vis light. Treatment of CP solutions with g-C₃N₄ nanosheets or TiO₂ alone in conjunction with irradiation gave removal efficiencies lower than 50%, which suggests the two act synergically to enhance the photocatalytic activity of the 40TiO₂/g-C₃N₄ nanocomposite. Superoxide and hydroxyl radicals are key active species produced during CP photodegradation. In addition, the observed nitrogen and Ti³⁺ defects and oxygen vacancies in the TiO₂/g-C₃N₄ nanocomposites may improve the light-harvesting ability of the composite and assist preventing rapid electron-hole recombination on the surface, enhancing the photocatalytic performance. In addition, interfacial interactions between the MCPs (low polarity) and thermally exfoliated carbon nitride in the TiO₂/g-C₃N₄ nanocomposites may also enhance MCP degradation.

Preparation of LDO@TiO2 core-shell nanosheets for enhanced photocatalytic degradation of organic pollution

TiO₂-based nanosheet materials with a core-shell structure are expected to be one of the promising photocatalysts for the degradation of organic pollution. It is a challenge to synthesize TiO₂ by the desired nucleation and growth process, so most reported TiO₂ core-shell photocatalysts are prepared using TiO₂ as a core material. Layered double hydroxides (LDHs) are considered ideal platforms to grow TiO₂in situ and further serve as additional components to improve the separation of photogenerated charge carriers. In this work, we report the design and fabrication of anatase TiO₂-coated ZnAl-layered double oxide (LDO@TiO₂) nanosheets, which involve the in situ growth of TiO₂ on ZnAl-LDH followed by subsequent calcination treatment. The resulting LDO@TiO₂ photocatalyst yields typical core-shell nanosheet morphology with a mesoporous structure, exhibiting excellent photodegradation and mineralization efficiency for organic pollution.

Compositing Two-Dimensional Materials with TiO2 for Photocatalysis

Energy shortage and environmental pollution problems boost in recent years. Photocatalytic technology is one of the most effective ways to produce clean energy—hydrogen and degrade pollutants under moderate conditions and thus attracts considerable attentions. TiO2 is considered one of the best photocatalysts because of its well-behaved photo-corrosion resistance and catalytic activity. However, the traditional TiO2 photocatalyst suffers from limitations of ineffective use of sunlight and rapid carrier recombination rate, which severely suppress its applications in photocatalysis. Surface modification and hybridization of TiO2 has been developed as an effective method to improve its photocatalysis activity. Due to superior physical and chemical properties such as high surface area, suitable bandgap, structural stability and high charge mobility, two-dimensional (2D) material is an ideal modifier composited with TiO2 to achieve enhanced photocatalysis process. In this review, we summarized the preparation methods of 2D material/TiO2 hybrid and drilled down into the role of 2D materials in photocatalysis activities.