Low-cost and simple FDM-based 3D-printed microfluidic device for the synthesis of metallic core–shell nanoparticles

Three-Dimensional Printing of Multifunctional Composites: Fabrication, Applications, and Biodegradability Assessment

Additive manufacturing, with its wide range of printable materials, and ability to minimize material usage, reduce labor costs, and minimize waste, has sparked a growing enthusiasm among researchers for the production of advanced multifunctional composites. This review evaluates recent reports on polymer composites used in 3D printing, and their printing techniques, with special emphasis on composites containing different types of additives (inorganic and biomass-derived) that support the structure of the prints. Possible applications for additive 3D printing have also been identified. The biodegradation potential of polymeric biocomposites was analyzed and possible pathways for testing in different environments (aqueous, soil, and compost) were identified, including different methods for evaluating the degree of degradation of samples. Guidelines for future research to ensure environmental safety were also identified.

Combining 3D Printing and Microfluidic Techniques: A Powerful Synergy for Nanomedicine

Nanomedicine has grown tremendously in recent years as a responsive strategy to find novel therapies for treating challenging pathological conditions. As a result, there is an urgent need to develop novel formulations capable of providing adequate therapeutic treatment while overcoming the limitations of traditional protocols. Lately, microfluidic technology (MF) and additive manufacturing (AM) have both acquired popularity, bringing numerous benefits to a wide range of life science applications. There have been numerous benefits and drawbacks of MF and AM as distinct techniques, with case studies showing how the careful optimization of operational parameters enables them to overcome existing limitations. Therefore, the focus of this review was to highlight the potential of the synergy between MF and AM, emphasizing the significant benefits that this collaboration could entail. The combination of the techniques ensures the full customization of MF-based systems while remaining cost-effective and less time-consuming compared to classical approaches. Furthermore, MF and AM enable highly sustainable procedures suitable for industrial scale-out, leading to one of the most promising innovations of the near future.

Polymeric Orthosis with Electromagnetic Stimulator Controlled by Mobile Application for Bone Fracture Healing: Evaluation of Design Concepts for Medical Use

Background: The occurrence of bone fractures is increasing worldwide, mainly due to the health problems that follow the aging population. The use of additive manufacturing and electrical stimulators can be applied for bioactive achievements in bone healing. However, such technologies are difficult to be transferred to medical practice. This work aims to develop an orthosis with a combined magnetic field (CFM) electrostimulator that demonstrates concepts and design aspects that facilitate its use in a real scenario. Methods: A 3D-printed orthosis made of two meshes was manufactured using PLA for outer mechanical stabilization mesh and TPU for inner fixation mesh to avoid mobilization. A CFM stimulator of reduced dimension controlled by a mobile application was coupled onto the orthosis. The design concepts were evaluated by health professionals and their resistance to chemical agents commonly used in daily activities were tested. Their thermal, chemical and electrical properties were also characterized. Results: No degradation was observed after exposure to chemical agents. The CMF achieved proper intensity (20-40 µT). The thermal analysis indicated its appropriate use for being modelled during clinical assessment. Conclusion: An orthosis with a coupled electrostimulator that works with a combined magnetic field and is controlled by mobile application was developed, and it has advantageous characteristics when compared to traditional techniques for application in real medical environments.

Evaluating commercial thermoplastic materials in fused deposition modeling 3D printing for their compatibility with DNA storage and analysis by quantitative polymerase chain reaction

Nucleic acids are ubiquitous in biological samples and can be sensitively detected using nucleic acid amplification assays. To achieve highly accurate and reliable results, nucleic acid isolation and purification is often required and can limit the accessibility of these assays. Encapsulation of these workflows onto a single device may be achieved through fabrication methodologies featuring commercial three-dimensional (3D) printers. This study aims to characterize fused deposition modeling (FDM) filaments based on their compatibility with nucleic acid storage using quantitative polymerase chain reaction (qPCR). To study the adsorption of nucleic acids, storage vessels were fabricated using six common thermoplastics including: polylactic acid (PLA), nylon, acrylonitrile butadiene styrene (ABS), co-polyester (CPE), polycarbonate (PC), and polypropylene (PP). DNA adsorption of a short 98 base pair and a longer 830 base pair fragment to the walls of the vessel was shown to vary significantly among the polymer materials as well as the color varieties of the same polymer. PLA storage vessels were found to adsorb the least amount of the 98 base pair DNA after 12 hours of storage in 2.5 M NaCl TE buffer whereas the ABS and PC vessels adsorbed up to 97.2 ± 0.2% and 97.5 ± 0.2%. DNA adsorption could be reduced by decreasing the layer height of the 3D printed object, thereby increasing the functionality of the ABS storage vessel. Nylon was found to desorb qPCR inhibiting components into the stored solution which led to erroneous DNA quantification data from qPCR analysis.

Facile Route for 3D Printing of Transparent PETg-Based Hybrid Biomicrofluidic Devices Promoting Cell Adhesion

3D printing has emerged as a promising fabrication technique for microfluidic devices, overcoming some of the challenges associated with conventional soft lithography. Filament-based polymer extrusion (popularly known as fused deposition modeling (FDM)) is one of the most accessible 3D printing techniques available, offering a wide range of low-cost thermoplastic polymer materials for microfluidic device fabrication. However, low optical transparency is one of the significant limitations of extrusion-based microfluidic devices, rendering them unsuitable for cell culture-related biological applications. Moreover, previously reported extrusion-based devices were largely dependent on fluorescent dyes for cell imaging because of their poor transparency. First, we aim to improve the optical transparency of FDM-based microfluidic devices to enable bright-field microscopy of cells. This is achieved using (1) transparent polymer filament materials such as poly(ethylene terephthalate) glycol (PETg), (2) optimized 3D printing process parameters, and (3) a hybrid approach by integrating 3D printed microfluidic devices with cast poly(dimethylsiloxane) (PDMS) blocks. We begin by optimizing four essential 3D printing process parameters (layer height, printing speed, cooling fan speed, and extrusion flow), affecting the overall transparency of 3D printed devices. Optimized parameters produce exceptional optical transparency close to 80% in 3D printed PETg devices. Next, we demonstrate the potential of FDM-based 3D printing to fabricate transparent micromixing devices with complex planar and nonplanar channel networks. Most importantly, cells cultured on native 3D printed PETg surfaces show excellent cell attachment, spreading, and proliferation during 3 days of culture without extracellular matrix coating or surface treatment. Next, we introduce L929 cells inside hybrid PETg-PDMS biomicrofluidic devices as a proof of concept. We demonstrate that 3D printed hybrid biomicrofluidic devices promote cell adhesion, allow bright-field microscopy, and maintain high cell viability for 3 days. Finally, we demonstrate the applicability of the proposed fabrication approach for developing 3D printed microfluidic devices from other FDM-compatible transparent polymers such as polylactic acid (PLA) and poly(methyl methacrylate) (PMMA).