The rate controlling mechanism in superplasticity

Superplastic Deformation of Alumina Composites Reinforced with Carbon Nanofibers and with Graphene Oxide Sintered by SPS-Experimental Testing and Theoretical Interpretation

The superplastic behavior of alumina-based nanostructured ceramics (Al₂O₃) is an important issue in the world of materials. The main body of this paper is an analysis of the creep behavior of polycrystals, with grain boundary sliding as the main deformation mechanism at high temperatures. Concomitant accommodation of grain shapes to preserve spatial continuity has a comparatively small effect on the strain rate. The constitutive equations for small deformations, relating strain and strain rate, derived from two models for grain sliding, are compared with the experimental data with their respective uncertainties. The data follow from experiments on the plastic deformation of alumina composites reinforced, on the one hand by graphene oxide, and on the other hand by carbon nanofibers sintered by SPS. The results show good agreement between experiment and theory for these advanced ceramics, particularly for one of the assumed models. The values obtained of ξ² for model A were in the interval 0.0002–0.1189, and for model B were in the interval 0.000001–0.0561. The values obtained of R² for model A were in the interval 0.9122–0.9994, and for model B were in the interval 0.9586–0.9999. The threshold stress was between (3.05 · 10⁻¹⁵–25.68) MPa.

Recent Development of Superplasticity in Aluminum Alloys: A Review

Aluminum alloys can be used in the fabrication of intricate geometry and curved parts for a wide range of uses in aerospace and automotive sectors, where high stiffness and low weight are necessitated. This paper outlines a review of various research investigations on the superplastic behavior of aluminum alloys that have taken place mainly over the past two decades. The influencing factors on aluminum alloys superplasticity, such as initial grain size, deformation temperature, strain rate, microstructure refinement techniques, and addition of trace elements in aluminum alloys, are analyzed here. Since grain boundary sliding is one of the dominant features of aluminum alloys superplasticity, its deformation mechanism and the corresponding value of activation energy are included as a part of discussion. Dislocation motion, diffusion in grains, and near-grain boundary regions being major features of superplasticity, are discussed as important issues. Moreover, the paper also discusses the corresponding values of grain size exponent, stress exponent, solute drag creep and power law creep. Constitutive equations, which are essential for commercial applications and play a vital role in predicting and analyzing the superplastic behavior, are also reviewed here.

Size effect on the deformation mechanisms of nanocrystalline platinum thin films

This paper reports a study of time-resolved deformation process at the atomic scale of a nanocrystalline Pt thin film captured in situ under a transmission electron microscope. The main mechanism of plastic deformation was found to evolve from full dislocation activity-enabled plasticity in large grains (with grain size d > 10 nm), to partial dislocation plasticity in smaller grains (with grain size 10 nm < d < 6 nm), and grain boundary-mediated plasticity in the matrix with grain sizes d < 6 nm. The critical grain size for the transition from full dislocation activity to partial dislocation activity was estimated based on consideration of stacking fault energy. For grain boundary-mediated plasticity, the possible contributions to strain rate of grain creep, grain sliding and grain rotation to plastic deformation were estimated using established models. The contribution of grain creep is found to be negligible, the contribution of grain rotation is effective but limited in magnitude, and grain sliding is suggested to be the dominant deformation mechanism in nanocrystalline Pt thin films. This study provided the direct evidence of these deformation processes at the atomic scale.

Mechanical Properties of Thin Film Aluminum Fibers: Grain Size Effects

Thin film aluminum fibers with grain sizes of 35 and 100 nm were pulled in a microtensile tester. The larger grains led to greater yield and tensile strengths but smaller strains to failure. Both samples had mechanical strengths 3–6 times greater than bulk aluminum. In addition, the small grained fibers had a strain rate sensitivity exponent of 0.26 suggesting diffusion controlled plastic deformation mechanisms.

Observations on Historical and Contemporary Developments in Superplasticity

The history of superplasticity is reviewed. The first scientific observation of superplasticity dates back to 1912. Sporadic reports of subsequent observations appear in the literature up to the review by Underwood in 1962. Since that time there have been a number of milestone achievements that have propelled the technology of superplasticity forward. These include commercial developments based on nickel, titanium, iron, and aluminum alloys. In more recent times the advent of superplasticity in ceramics and intermetallics has stimulated yet further interest in the field. At the present time there are major research efforts underway in the USA, USSR, Japan, China, and Europe to apply superplastic forming technology to the manufacture of complex components.

Creep deformation in a 3mol% Y2O3-Stabilized Tetragonal Zirconia

The high temperature deformation behavior of a 3mol% yttria-stabilized tetragonal zirconia (3Y-TZP) is examined. The analysis of creep strain rate, which was monitored directly with an optical extensometer and corrected for the current grain size, reveals a sigmoidal feature in the true stress-creep rate relationship. At lower stresses, a stress exponent n of ∼1.6 incorporated with a grain size exponent of 2.0 suggests the intervention of a lattice diffusion creep mechanism. For higher stresses where n ∼2.7, evidence of intragranular dislocation activities suggests that dislocations may play an important role in the accommodation process for grain boundary sliding in 3Y-TZP.