Characterisation of ultrafiltration membranes by impedance spectroscopy. I. Determination of the separate electrical parameters and porosity of the skin and sublayers

The Effect of Benzyl Alcohol on the Dielectric Structure of Lipid Bilayers

Molecularly tethered lipid bilayer membranes were constructed on a commercially available chemically modified gold substrate. This is a new and promising product that has allowed the construction of very robust lipid bilayers. Very high resolution electrical impedance spectroscopy (EIS) was used to determine the dielectric structure of the lipid bilayers and associated interfaces. The EIS data were modelled in terms of the dielectric substructure using purpose developed software. The hydrophobic region, where the lipid tails are located, was revealed by the EIS in the frequency range of (1-100) Hz and its thickness was calculated from the capacitance of this region and found to be approximately 3-4 nm. The hydrophilic region, where the polar heads are located, was revealed at higher frequencies and its thickness was estimated to be approximately 1-2 nm. The effect of the local anaesthetic benzyl alcohol (BZA) on the tethered lipid bilayers was investigated. The effect of BZA on the membrane capacitance and conductance allowed the changes in the thickness of the polar head and hydrophobic tails regions to be determined. It was found that the addition of BZA caused a significant increase in the capacitance (corresponding to a decrease in the thickness) of the hydrophobic region and an increase in the membrane electrical conductance. The EIS allowed a distinction between a hydrophobic region in the centre of the bilayer and an outer hydrophobic region. Benzyl alcohol was found to have the largest effect on the outer, hydrophobic region, although the inner hydrophobic region was also consistently affected.

Determining nanocapillary geometry from electrochemical impedance spectroscopy using a variable topology network circuit model

Solid-state nanopores and nanocapillaries find increasing use in a variety of applications including DNA sequencing, synthetic nanopores, next-generation membranes for water purification, and other nanofluidic structures. This paper develops the use of electrochemical impedance spectroscopy to determine the geometry of nanocapillaries. A network equivalent circuit element is derived to include the effects of the capacitive double layer inside the nanocapillaries as well as the influence of varying nanocapillary radius. This variable topology function is similar to the finite Warburg impedance in certain limits. Analytical expressions for several different nanocapillary shapes are derived. The functions are evaluated to determine how the impedance signals will change with different nanocapillary aspect ratios and different degrees of constriction or inflation at the capillary center. Next, the complex impedance spectrum of a nanocapillary array membrane is measured at varying concentrations of electrolyte to separate the effects of nanocapillary double layer capacitance from those of nanocapillary geometry. The variable topology equivalent circuit element model of the nanocapillary is used in an equivalent circuit model that included contributions from the membrane and the measurement apparatus. The resulting values are consistent with the manufacturer's specified tolerances of the nanocapillary geometry. It is demonstrated that electrochemical impedance spectroscopy can be used as a tool for in situ determination of the geometry of nanocapillaries.

Dielectric spectroscopy of a nanofiltration membranes-electrolyte solution system: I. Low-frequency dielectric relaxation from the counterion polarization in pores and model development

The dielectric spectra of nanofiltration membranes NF90, NF-, and NF270 in eight electrolytes, NaCl, KCl, CuCl(2), MgCl(2), Na(2)SO(4), K(2)SO(4), MgSO(4), and CuSO(4), were investigated as a function of the electrolyte concentration over a frequency range from 40 Hz to 11 MHz. Two relaxations were observed: the one at high frequency was caused by interfacial polarization between the membrane and electrolyte, and the low-frequency relaxation, on which we focus on in this work, was confirmed to be due to the counterion polarization effects in the pores of the membrane. A model of cylindrical pores which were dispersed in membrane base was developed to interpret the low-frequency relaxation. On the basis of this model, we amended the expression deduced by Takashima for describing the dielectric behavior of a cylinder particle suspension to fit our dielectric data from the low-frequency relaxation. The data fitting with this improved expression was suitable for all the systems measured in this work; structural and electrical parameters such as the radius of the pore in the membrane, the thickness of the active layer of the membrane, surface charged density, and zeta potential on the pore wall were obtained finally.

Characterization of ionic transport at the nanoscale

This paper reports on the development of a multi-layer microscale impedance measurement system with integrated working, counter, and reference electrodes that can be used to probe transport at the nanoscale. System fabrication and testing are carried out to demonstrate the feasibility of such a system for characterizing transport through nanocapillary array membranes (NCAMs). Results indicate that transport through NCAMs is a complex phenomenon, and impedance does not scale linearly with either pore diameter or ionic concentration. Use of a microscale construct for probing ionic transport at the nanoscale appears to be a promising path forward with further development.

Recent developments on ion-exchange membranes and electro-membrane processes

Rapid growth of chemical and biotechnology in diversified areas fuels the demand for the need of reliable green technologies for the down stream processes, which include separation, purification and isolation of the molecules. Ion-exchange membrane technologies are non-hazardous in nature and being widely used not only for separation and purification but their application also extended towards energy conversion devices, storage batteries and sensors etc. Now there is a quite demand for the ion-exchange membrane with better selectivities, less electrical resistance, high chemical, mechanical and thermal stability as well as good durability. A lot of work has been done for the development of these types of ion-exchange membranes during the past twenty-five years. Herein we have reviewed the preparation of various types of ion-exchange membranes, their characterization and applications for different electro-membrane processes. Primary attention has been given to the chemical route used for the membrane preparation. Several general reactions used for the preparation of ion-exchange membranes were described. Methodologies used for the characterization of these membranes and their applications were also reviewed for the benefit of readers, so that they can get all information about the ion-exchange membranes at one platform. Although there are large number of reports available regarding preparations and applications of ion-exchange membranes more emphasis were predicted for the usefulness of these membranes or processes for solving certain type of industrial or social problems. More efforts are needed to bring many products or processes to pilot scale and extent their applications.

Modification of polysulfone membranes with polyethylene glycol and lignosulfate: electrical characterization by impedance spectroscopy measurements

Two sets of composite membranes having an asymmetric sulfonated polysulfone membrane as support layer have been obtained and electrically characterized (membranes SPS-PEG and PA-LIGS). The skin layer of the membrane SPS-PEG contains different percentages of polyethylene glycol in the casting solution (5, 25, 40, and 60 wt%), while lignosulfonate was used for manufacturing PA-LIGS membranes (5, 10, 20, and 40 wt%). Membrane electrical characterization was done by means of impedance spectroscopy (IS) measurements, which were carried out with the membranes in contact with NaCl solutions at different concentrations (10(-3) < or = c(M) < or = 5x10(-2)). Electrical resistance and equivalent capacitance of the different membrane samples were determined from IS plots by using equivalent circuits as models. Results show a clear decrease in the membrane electrical resistance as a result of both polysulfone sulfonation and the increase of the concentration of modifying substances, although a kind of limit concentration was obtained for both polyethylene glycol and lignosulfonate (40 and 20%, respectively). Results also show a decrease of around 90% in electrical resistance due to polysulfone sulfonation, while the value of the dielectric constant (hydrated state) clearly increases.

Dielectric Relaxation on the Intermediate Layer in a Bipolar Membrane under the Water Splitting Phenomenon

In this study, we investigated the impedance spectra of bipolar membranes. Under the application of a reverse-biased voltage, the spectra showed a double dielectric relaxation profile due to the heterogeneous structure and it was analyzed in accordance with the three-layered dielectric model. It is defined that one of the compositions of the heterogeneous structure is situated at the membrane interface region between the negatively and the positively charged membrane with a thickness of less than several micrometers, which has an extraordinarily large electric capacity with a magnitude of sub-microfarads. It is concluded that this layer is identified with the intermediate layer in which the water splitting phenomenon occurs on the bipolar membrane.

Electrochemical Characterization of an Asymmetric Nanofiltration Membrane with NaCl and KCl Solutions: Influence of Membrane Asymmetry on Transport Parameters

Electrochemical characterization of a nanofiltration asymmetric membrane was carried out by measuring membrane potential, salt diffusion, and electrical parameters (membrane electrical resistance and capacitance) with the membrane in contact with NaCl and KCl solutions at different concentrations (10(-3)< or =c(M)< or =5 x 10(-2)). From these experiments characteristic parameters such as the effective concentration of charge in the membrane, ionic transport numbers, and salt and ionic permeabilities across the membrane were determined. Membrane electrical resistance and capacitance were obtained from impedance spectroscopy (IS) measurements by using equivalent circuits as models. This technique allows the determination of the electrical contribution associated with each sublayer; then, assuming that the dense sublayer behaves as a plane capacitor, its thickness can be estimated from the capacitance value. The influence of membrane asymmetry on transport parameters have been studied by carrying out measurements for the two opposite external conditions. Results show that membrane asymmetry strongly affects membrane potential, which is attributed to the Donnan exclusion when the solutions in contact with the dense layer have concentrations lower than the membrane fixed charge (X(ef) approximately -0.004 M), but for the reversal experimental condition (high concentration in contact with the membrane dense sublayer) the membrane potential is practically similar to the solution diffusion potential. The comparison of results obtained for both electrolytes agrees with the higher conductivity of KCl solutions. On the other hand, the influence of diffusion layers at the membrane/solution interfaces in salt permeation was also studied by measuring salt diffusion at a given NaCl concentration gradient but at five different solutions stirring rates.