A novel electrochemiluminescence sensor based on resonance energy transfer system between nitrogen doped graphene quantum dots and boron nitride quantum dots for sensitive detection of folic acid

Transient absorption study on fluorescence quenching of InP/ZnS quantum dots by MXene

Fluorescence quenching due to energy transfer from InP/ZnS quantum dots (QDs) to Ti3C2Tx MXene materials was investigated by the transient absorption spectroscopy. During the fluorescence quenching, the photo-induced absorption feature in the transient spectrum was blue-shifted due to the higher photon energy required for the upward transition. The lifetime of stimulated emission was gradually extended from 0.86 μs to 2.28 μs with increasing Ti3C2Tx MXene. The fluorescence quenching of QDs can be quantitatively characterized by analyzing the lifetime of the stimulated emission feature in the transient absorption spectrum, which was used as a Ti3C2Tx MXene detection with the sensitivity of 6.63 mL/mg. The results of this study provide the basis for the design of optical sensors.

A differential strategy to enhance the anti-interference ability of molecularly imprinted electrochemiluminescence sensor with a semi-logarithmic calibration curve

The non-specific adsorption behaviors of various interferents on the surface of a molecularly imprinted polymer (MIP) are adverse for the selectivity of an MIP-based sensor, which can be overcome via a differential strategy by using the differential signal between MIP- and non-imprinted polymer (NIP)-based sensors. However, the normal differential mode is not suitable for the MIP-based sensors with non-linear calibration curves. Herein, an improved differential strategy is reported for an MIP-based sensor with a semi-logarithmic calibration curve, demonstrated by an electrochemiluminescence (ECL) sensor for dopamine (DA). Glassy carbon electrode (GCE) was modified by the mixture of g-C3N4, TiO2 nanoparticles (NPs) and carbon nanotubes (CNTs). MIP membrane for DA was fabricated on the surface of g-C3N4/TiO2NPs/CNTs/GCE using chitosan for film-forming, obtained MIP@GCE. To enhance the anti-interference ability of the MIP-based DA sensor, the difference between exponential functions ECL intensities of MIP@GCE and NIP@GCE is used as the analytical signal in the improved differential strategy. The differential signal was increased linearly with increasing DA concentration ranging from 10 pM to 0.10 μM, with the detection limit of 5.6 pM. The interference level of Cu2+ on DA determination in the improved differential mode is only 9.7% of that in the normal MIP mode. The improved differential strategy can be used in other MIP-based sensors with semi-logarithmic calibration curves.

FRET-based probe for ratiometric detection and imaging of folic acid in real-time

Inadequate folic acid intake is linked to diseases such as megaloblastic anemia, neural tube defects, and hyperhomocysteinemia, increasing the risk of vascular disease and thrombosis. Folic acid, a cofactor in various enzymes, can be produced by plants and bacteria, but not by humans and other animals. L-5-methyl-tetrahydrofolate (L-5-methyl-THF) is the primary dietary folate form, transported in circulation for cellular metabolism. Traditional methods of determining folic acid levels are unreliable and time-consuming. SenFol (Sensor for folic acid) is a fluorescence resonance energy transfer (FRET)-based nanosensor that we have developed by inserting folic acid-binding protein (FolT) as the folate detecting domain between the pair of enhanced cyan fluorescent protein (ECFP) and Venus. The developed sensor is highly specific, produces a quick signal, which is pH stable, and delivers precise, ratiometric readings in cell-based experiments. The projected affinity score of folic acid with FolT was -7.4 kcal/mol. The apparent affinity (Kd) of SenFol for folic acid is 28.49 × 10-9 M, with a detection range of 5 × 10-9 M to 5 × 10-7 M, and a maximum FRET ratio change of 0.45. WT SenFol, a highly efficient folic acid nanosensor, can dynamically detect intracellular folic acid content in E. coli, yeast, and HEK-293 T cells, confirming its potential.

Determination of chloramphenicol in food using nanomaterial-based electrochemical and optical sensors-A review

Chloramphenicol (CAP) is a widely used antibiotic for the treatment of sick animals owing to its potent action and low cost. However, the accumulation of CAP in the human body can cause irreversible aplastic anemia and hematopoietic toxicity. Accordingly, development of various analytical techniques for the rapid detection of CAP in animal products and the related processed foods is necessary. Among these analytical techniques, electrochemical and optical sensors offer many advantages for CAP detection, including high sensitivity, simple operation and fast analysis speed. In this review, we summarize recent application of carbon nanomaterials, metal nanoparticles, metal oxide nanoparticles and metal organic framework in the development of electrochemical and optical sensors for CAP detection (2010-2022). Based on the advantages and disadvantages of nanomaterials, electrochemical and optical sensors are summarized in this review. The preparation and synthesis of electrochemical and optical sensors and nanomaterials in the field of rapid detection are prospected.

In situ electrodeposition of bismuth oxide nanowires @MWNT on the carbon fiber microelectrode for the sensitively electrochemical detection of folic acid

A microminiaturized electrochemical device, BiO@CNW/CFE was fabricated based on the in situ co-electrodeposition of bismuth oxide nanowires (BiNWs) and multi-walled carbon nanotubes (MWNTs) on the surface of carbon fiber electrode (CFE). The nanostructure of BiNWs could bind MWNTs on the surface of CFE during the precipitation of bismuth at the potential of -1.1 V. The vimineous nanostructure of BiO@CNW improved the surface area and electrochemical activity of the microelectrode. With the low background noise, folic acid (FA) can be detected sensitively by BiO@CNW/CFE based on the electrochemical reduction via the method of square wave voltammetry. The linear range of FA in sodium acetate-acetic acid buffer was achieved in the range of 5.00 nM-200 nM, the detection limit was estimated to be 0.63 nM. The recoveries of FA in human serum and artificial cerebral spinal fluid were between 99% and 103%, which indicates BiO@CNW/CFE was a reliable sensor for the detection of FA in biological samples.

Optical Biosensor Based on Graphene and Its Derivatives for Detecting Biomolecules

Graphene and its derivatives show great potential for biosensing due to their extraordinary optical, electrical and physical properties. In particular, graphene and its derivatives have excellent optical properties such as broadband and tunable absorption, fluorescence bursts, and strong polarization-related effects. Optical biosensors based on graphene and its derivatives make nondestructive detection of biomolecules possible. The focus of this paper is to review the preparation of graphene and its derivatives, as well as recent advances in optical biosensors based on graphene and its derivatives. The working principle of face plasmon resonance (SPR), surface-enhanced Raman spectroscopy (SERS), fluorescence resonance energy transfer (FRET) and colorimetric sensors are summarized, and the advantages and disadvantages of graphene and its derivatives applicable to various types of sensors are analyzed, and the methods of surface functionalization of graphene and its derivatives are introduced; these optical biosensors can be used for the detection of a range of biomolecules such as single cells, cellular secretions, proteins, nucleic acids, and antigen-antibodies; these new high-performance optical sensors are capable of detecting changes in surface structure and biomolecular interactions with the advantages of ultra-fast detection, high sensitivity, label-free, specific recognition, and the ability to respond in real-time. Problems in the current stage of application are discussed, as well as future prospects for graphene and its biosensors. Achieving the applicability, reusability and low cost of novel optical biosensors for a variety of complex environments and achieving scale-up production, which still faces serious challenges.

The role of doping strategy in nanoparticle-based electrochemiluminescence biosensing

Doping plays a crucial role in electrochemiluminescence (ECL) due to the followings: (1) Modulation of electronic structure, alteration of the surface state of nanoparticles (NPs), providing effective protection from the surrounding environment, thereby leading to ECL emitters with exceptional properties including tunable spectra, high luminescence efficiency, low excitation potential, and good stability. (2) Employment of doped NPs as promising coreactant alternatives due to the presence of functional groups such as amines induced by NP doping. (3) Serving as novel co-reaction accelerators (CRAs) for ECL through doping induced high catalytic properties. (4) Behaving as excellent carriers to load ECL emitters, recognition elements, and catalysts due to doping-induced larger surface area, higher conductivity and better biocompatibility of NPs. As a consequence, doped NPs have aroused broad interest and found wide applications in various ECL sensing platforms. In this review, the current promising improvements, concepts, and excellent applications of doped NPs for ECL biosensing are addressed. We aim to bring to light the physicochemical characteristics of various doped NPs that endow them with appealing ECL performance, leading to diverse applications in biosensing.

Recent Progress in Fabrication and Application of BN Nanostructures and BN-Based Nanohybrids

Due to its unique physical, chemical, and mechanical properties, such as a low specific density, large specific surface area, excellent thermal stability, oxidation resistance, low friction, good dispersion stability, enhanced adsorbing capacity, large interlayer shear force, and wide bandgap, hexagonal boron nitride (h-BN) nanostructures are of great interest in many fields. These include, but are not limited to, (i) heterogeneous catalysts, (ii) promising nanocarriers for targeted drug delivery to tumor cells and nanoparticles containing therapeutic agents to fight bacterial and fungal infections, (iii) reinforcing phases in metal, ceramics, and polymer matrix composites, (iv) additives to liquid lubricants, (v) substrates for surface enhanced Raman spectroscopy, (vi) agents for boron neutron capture therapy, (vii) water purifiers, (viii) gas and biological sensors, and (ix) quantum dots, single photon emitters, and heterostructures for electronic, plasmonic, optical, optoelectronic, semiconductor, and magnetic devices. All of these areas are developing rapidly. Thus, the goal of this review is to analyze the critical mass of knowledge and the current state-of-the-art in the field of BN-based nanomaterial fabrication and application based on their amazing properties.

Functionalization of 2D MoS2 Nanosheets with Various Metal and Metal Oxide Nanostructures: Their Properties and Application in Electrochemical Sensors

Two-dimensional transition metal dichalcogenides (2D TMDs) have gained considerable attention due to their distinctive properties and broad range of possible applications. One of the most widely studied transition metal dichalcogenides is molybdenum disulfide (MoS₂). The 2D MoS₂ nanosheets have unique and complementary properties to those of graphene, rendering them ideal electrode materials that could potentially lead to significant benefits in many electrochemical applications. These properties include tunable bandgaps, large surface areas, relatively high electron mobilities, and good optical and catalytic characteristics. Although the use of 2D MoS₂ nanosheets offers several advantages and excellent properties, surface functionalization of 2D MoS₂ is a potential route for further enhancing their properties and adding extra functionalities to the surface of the fabricated sensor. The functionalization of the material with various metal and metal oxide nanostructures has a significant impact on its overall electrochemical performance, improving various sensing parameters, such as selectivity, sensitivity, and stability. In this review, different methods of preparing 2D-layered MoS₂ nanomaterials, followed by different surface functionalization methods of these nanomaterials, are explored and discussed. Finally, the structure-properties relationship and electrochemical sensor applications over the last ten years are discussed. Emphasis is placed on the performance of 2D MoS₂ with respect to the performance of electrochemical sensors, thereby giving new insights into this unique material and providing a foundation for researchers of different disciplines who are interested in advancing the development of MoS₂-based sensors.

Electrochemiluminescent determination of CYFRA21-1 serum levels using Ti-Fe-O nanotubes immunoassay

Prominent electrochemiluminescence (ECL) in Ti-Fe-O nanotube arrays (Ti-Fe-O NTs) with K₂S₂O₈ as the cathode coreactant is reported for the first time. Compared with pure titanium dioxide nanotubes (TiO₂ NTs), this heterojunction could effectively reduce the band gap, facilitate electronic transitions, and move the ECL potential to a positive direction. The ECL performance motivated the development of an ultrasensitive ECL immunosensor for detecting cytokeratin fragment 21-1 (CYFRA21-1). Magnetic beads loaded with conductive carbon black (CCB/MNTs) were used to efficiently quench the ECL signal of a Ti-Fe-O NTs electrode and were combined with an ECL immunoassay to realize sensitive detection of CYFRA21-1. Over a CYFRA21-1 concentration range of 1.0 pg·mL^-1 ~ 100 ng·mL^-1, the change in the ECL signal was highly linear with the logarithm of the CYFRA21-1 concentration, and the limit of detection (LOD) was 0.114 pg·mL^-1. This ECL immunosensor was used to successfully determine the CYFRA21-1 content in serum. The recovery of CYFRA21-1 in actual serum was 88.6 - 104.4%, and the RSD was 1.4 - 3.0%. The coreaction solution used in this work was PBS (0.1 M, pH = 7.4) containing 0.05 M K₂S₂O₈, the scanning range was -1.0 - 0 V, the photomultiplier tube (PMT) was set to 750 V, and the scanning rate was 100 mV·s^-1.

Chloramphenicol-activated electro-chemiluminescent behavior of BNQDs-Ru(phen)32+ system for ultra-sensitive sensing of chloramphenicol in pharmaceutical and milk samples

To improve the sensitivity for electro-chemiluminescent (ECL) detection of chloramphenicol (CAP), a common broad-spectrum antibiotic, boron nitride quantum dots (BNQDs) were prepared with excellent photoelectric property and low toxicity. After its structure and electrochemical property were investigated in detail, it was noted that the ECL signal of Ru(Phen)₃²⁺could be strengthened by the proposed BNQDs, which was further activated by ten's times in the presence of CAP. Under the optimized conditions, there was an excellent linear relationship between ΔECL and lgc_CAPin a wide linear range from 1.0 × 10^-10to 1.0 × 10^-6mol l^-1CAP. The detection limit was super-low to be 3.3 × 10^-11mol l^-1(S/N = 3). When applied for CAP detection in real pharmaceutical and food samples, the recoveries were between 97.8% and 105.7% with R.S.D. less than 3.3%. A possible CAP-activated ECL mechanism of BNQDs-Ru(phen)₃²⁺was also proposed. This work will offer a great potential for efficient monitoring of CAP pollution and clinical diagnosing of CAP-related diseases in future.

Synthesis, Applications, and Prospects of Graphene Quantum Dots: A Comprehensive Review

Graphene quantum dot (GQD) is one of the youngest superstars of the carbon family. Since its emergence in 2008, GQD has attracted a great deal of attention due to its unique optoelectrical properties. Non-zero bandgap, the ability to accommodate functional groups and dopants, excellent dispersibility, highly tunable properties, and biocompatibility are among the most important characteristics of GQDs. To date, GQDs have displayed significant momentum in numerous fields such as energy devices, catalysis, sensing, photodynamic and photothermal therapy, drug delivery, and bioimaging. As this field is rapidly evolving, there is a strong need to identify the emerging challenges of GQDs in recent advances, mainly because some novel applications and numerous innovations on the ease of synthesis of GQDs are not systematically reviewed in earlier studies. This feature article provides a comparative and balanced discussion of recent advances in synthesis, properties, and applications of GQDs. Besides, current challenges and future prospects of these emerging carbon-based nanomaterials are also highlighted. The outlook provided in this review points out that the future of GQD research is boundless, particularly if upcoming studies focus on the ease of purification and eco-friendly synthesis along with improving the photoluminescence quantum yield and production yield of GQDs.

Electrochemiluminescence biosensor based on molybdenum disulfide-graphene quantum dots nanocomposites and DNA walker signal amplification for DNA detection

Based on the prominent electrochemiluminescence (ECL) performances of molybdenum disulfide-graphene quantum dots (MoS2-GQDs) nanocomposite and combined with enzyme-assisted recycling DNA walker signal amplification, an "on-off" switch ECL biosensor was proposed for sensitive assay of specific DNA sequences. Noticeably, MoS2 with two-dimensional nanosheet structure increased the loading capacity of GQDs to support abundant hairpin DNA (H). The composites of MoS2 and GQDs facilitated the charge transfer in ECL process, which significantly improved the ECL signal to achieve an "on" state. Then, the DNA walker cyclic amplification was performed by adding the target DNA and exonuclease III (Exo III). Finally, the DNA2-Fc-DNA1 was introduced into the system as ECL signal quencher, turning the ECL signal into an "off" state. The sensitive assay of ultra-low concentration specific DNA sequences was realized according to the variation of ECL signal strength before and after the existence of target DNA. The proposed ECL biosensor showed a good linear relationship ranging from 1 nM to 100 aM with a detection limit of 25.1 aM, providing a powerful strategy for biomedical research and clinical analysis.

Ultrasensitive electrochemiluminescence sensor based on nitrogen-decorated carbon dots for Listeria monocytogenes determination using a screen-printed carbon electrode

Current method for identification of foodborne pathogens suffers from its relatively poor performance, consequently limiting its use. Herein, we first describe an ultrasensitive electrochemiluminescence (ECL) sensor based on nitrogen-decorated carbon dots (NCDs) for Listeria monocytogenes (L. monocytogenes) determination using a screen-printed carbon electrode (SPCE). Citric acid serves as carbon source, and ethylenediamine, a molecule containing nitrogen atom, is employed to synthesize CDs. Approximately 4 nm NCD with homogenous size distribution can be produced via a single step green microwave-assisted methodology. The construction of ECL sensor is initiated by the immobilization of capture antibody (Ab1) onto the carboxyl graphene (GOOH)-modified SPCE, where immunocomplexes (antigen and the NCD-labelled secondary antibody (Ab2-NCD)) are formed, resulting in a substantial increment in the ECL signal response in the presence of K₂S₂O₈. The GOOH allows direct formation of the capture antibodies and enhances the electrochemical properties. Under optimal parameters, this sensor exhibits wide linearity (2 to 1.0 × 10⁶ CFU mL^-1), high sensitivity (0.104 or 1.0 × 10^-1 CFU mL^-1) and specificity over the nontargeting studied pathogens and is successfully applied to determine L. monocytogenes in food products. These promising results together with its performance suggest that this proposed platform may serve as an alternative device to effectively control the spread of foodborne diseases.

Recent advances in heteroatom-doped graphene quantum dots for sensing applications

Graphene quantum dots (GQDs) are carbon-based fluorescent nanomaterials having various applications due to attractive properties. But the low photoluminescence (PL) yield and monochromatic PL behavior of GQDs put limitations on their real-time applications. Therefore, heteroatom doping of GQDs is recognized as the best approach to modify the optical as well as electronic properties of GQDs by modifying their chemical composition and electronic structure. In this review, the new strategies for preparing the heteroatom (N, B, S, P) doped GQDs by using different precursors and methods are discussed in detail. The particle size, emission wavelength, PL emissive color, and quantum yield of recently developed heteroatom doped GQDs are reported in this article. The investigation of structure, crystalline nature, and composition of heteroatom doped GQDs by various characterization techniques such as high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) are also described. The recent progress on the impact of mono or co-doping of heteroatoms on PL behavior, and optical, electrochemiluminescence (ECL), and electrochemical properties of GQDs is also surveyed. Further, heteroatom doped GQDs with attractive properties used in sensing of various metal ions, biomolecules, small organic molecules, etc. by using various techniques with different limits of detection are also summarized. This review provides progressive trends in the development of heteroatom doped GQDs and their various applications.

A Review on van der Waals Boron Nitride Quantum Dots

Boron nitride quantum dots (BNQDs) have gained increasing attention for their versatile fluorescent, optoelectronic, chemical, and biochemical properties. During the past few years, significant progress has been demonstrated, started from theoretical modeling to actual application. Many interesting properties and applications have been reported, such as excitation-dependent emission (and, in some cases, non-excitation dependent), chemical functionalization, bioimaging, phototherapy, photocatalysis, chemical, and biological sensing. An overview of this early-stage research development of BNQDs is presented in this article. We have prepared un-bias assessments on various synthesis methods, property analysis, and applications of BNQDs here, and provided our perspective on the development of these emerging nanomaterials for years to come.

Advances in the Application of Aptamer Biosensors to the Detection of Aminoglycoside Antibiotics

Antibiotic abuse is becoming increasingly serious and the potential for harm to human health and the environment has aroused widespread social concern. Aminoglycoside antibiotics (AGs) are broad-spectrum antibiotics that have been widely used in clinical and animal medicine. Consequently, their residues are commonly found in animal-derived food items and the environment. A simple, rapid, and sensitive detection method for on-site screening and detection of AGs is urgently required. In recent years, with the development of molecular detection technology, nucleic acid aptamers have been successfully used as recognition molecules for the identification and detection of AGs in food and the environment. These aptamers have high affinities, selectivities, and specificities, are inexpensive, and can be produced with small batch-to-batch differences. This paper reviews the applications of aptamers for AG detection in colorimetric, fluorescent, chemiluminescent, surface plasmon resonance, and electrochemical sensors for the analysis in food and environmental samples. This study provides useful references for future research.

Human virus detection with graphene-based materials

Our recent experience of the COVID-19 pandemic has highlighted the importance of easy-to-use, quick, cheap, sensitive and selective detection of virus pathogens for the efficient monitoring and treatment of virus diseases. Early detection of viruses provides essential information about possible efficient and targeted treatments, prolongs the therapeutic window and hence reduces morbidity. Graphene is a lightweight, chemically stable and conductive material that can be successfully utilized for the detection of various virus strains. The sensitivity and selectivity of graphene can be enhanced by its functionalization or combination with other materials. Introducing suitable functional groups and/or counterparts in the hybrid structure enables tuning of the optical and electrical properties, which is particularly attractive for rapid and easy-to-use virus detection. In this review, we cover all the different types of graphene-based sensors available for virus detection, including, e.g., photoluminescence and colorimetric sensors, and surface plasmon resonance biosensors. Various strategies of electrochemical detection of viruses based on, e.g., DNA hybridization or antigen-antibody interactions, are also discussed. We summarize the current state-of-the-art applications of graphene-based systems for sensing a variety of viruses, e.g., SARS-CoV-2, influenza, dengue fever, hepatitis C virus, HIV, rotavirus and Zika virus. General principles, mechanisms of action, advantages and drawbacks are presented to provide useful information for the further development and construction of advanced virus biosensors. We highlight that the unique and tunable physicochemical properties of graphene-based nanomaterials make them ideal candidates for engineering and miniaturization of biosensors.

Gold-Nanoparticle-Functionalized Cobalt-Nickel Phosphate 3D Nanoice Creams to Fabricate Stable and Sensitive Biosensors for the Cytochrome c Assay

Designing a stable and sensitive luminol-based electrochemiluminescence (ECL) analytical platform in the neutral condition has attracted a lot of attention. Here, gold-nanoparticle-functionalized cobalt-nickel phosphate three-dimensional nanoice creams (Au@Co₃Ni₃(PO₄)₄ NICs) are successfully prepared via electrostatic interaction. Generally, cobalt-nickel phosphate nanoice creams (Co₃Ni₃(PO₄)₄ NICs) are synthesized via a mild hydrothermal method and functionalized via polyethylenimine (PEI). Then, Au NPs are adsorbed on the surface of Co₃Ni₃(PO₄)₄ NICs via Au-N weak interaction to fabricate Au@Co₃Ni₃(PO₄)₄ NICs. Owing to the important roles of Au@Co₃Ni₃(PO₄)₄ in exhibiting excellent electrocatalytic activity, as well as preventing the deposition of negatively charged oxidation product induced electrode passivation, luminol in the nanohybrids (LH-Au@Co₃Ni₃(PO₄)₄) gives strong and stable ECL intensity in the neutral conditions. Moreover, the ECL emission of luminol is obviously quenched based on the resonance energy transfer (RET) between luminol as donor and cytochrome c (Cyt c) as acceptor. Hence, a sensitive ECL biosensor is successfully fabricated for the quantitative determination of Cyt c in cell lysates and exhibits wide linear ranges of 1.0 × 10^-4-0.5 × 10^-5 and 0.5 × 10^-5-1.0 × 10^-8 M as well as a low detection limit of 2.48 nM. This novel sensing strategy will broaden the application of transition metal (Co, Ni) phosphates in bioassays.

Electrochemiluminescence Detection of Sunset Yellow by Graphene Quantum Dots

Use of food additives, such as colorants and preservatives, is highly regulated because of their potential health risks to humans. Therefore, it is important to detect these compounds effectively to ensure conformance with industrial standards and to mitigate risk. In this paper, we describe the preparation and performance of an ultrasensitive electrochemiluminescence (ECL) sensor for detecting a key food additive, sunset yellow. The sensor uses graphene quantum dots (GQDs) as the luminescent agent and potassium persulfate as the co-reactant. Strong and sensitive ECL signals are generated in response to trace amounts of added sunset yellow. A detection limit (signal-to-noise ratio = 3) of 7.6 nM and a wide linear range from 2.5 nM to 25 μM are demonstrated. A further advantage of the method is that the luminescent reagents can be recycled, indicating that the method is sustainable, in addition to being simple and highly sensitive.