Flashing light in microalgae biotechnology

Utilizing CO2 in industrial off-gas for microalgae cultivation: considerations and solutions

The utilization of microalgae to treat carbon dioxide (CO2)-rich industrial off-gas has been suggested as both beneficial for emissions reduction and economically favorable for the production of microalgal products. Common sources of off-gases include coal combustion (2-15% CO2), cement production (8-15% CO2), coke production (18-23% CO2), and ore smelting (6-7% CO2). However, industrial off-gas also commonly contains other acid gas components [typically nitrogen oxides (NOX) and sulfur dioxide (SO2)] and metals that could inhibit microalgae growth and productivity. To utilize industrial off-gas effectively in microalgae cultivation systems, a number of solutions have been proposed to overcome potential inhibitions. These include bioprospecting to identify suitable strains, genetic modification to improve specific cellular characteristics, chemical additions, and bioreactor designs and operating procedures.In this review, results from microalgae experiments related to utilizing off-gas are presented, and the outcomes of different conditions discussed along with potential solutions to resolve limitations associated with the application of off-gas.

A Comparison of the Effects of Continuous Illumination and Day/Night Regimes on PHB Accumulation in Synechocystis Cells

Poly(3-hydroxybutyrate) (PHB) is a biobased and biodegradable polymer with properties comparable to polypropylene and therefore has the potential to replace conventional plastics. PHB is intracellularly accumulated by prokaryotic organisms. For the cells PHB functions manly as carbon and energy source, but all possible functions of PHB are still not known. Synechocystis (cyanobacteria) accumulates PHB using light as energy and CO2 as carbon source. The main trigger for PHB accumulation in cyanobacteria is nitrogen and phosphorous depletion with simultaneous surplus of carbon and energy. For the above reasons, obtaining knowledge about external factors influencing PHB accumulation is of highest interest. This study compares the effect of continuous light exposure and day/night (16/8 h) cycles on selected physiology parameters of three Synechocystis strains. We show that continuous illumination at moderate light intensities leads to an increased PHB accumulation in Synechocystis salina CCALA 192 (max. 14.2% CDW - cell dry weight) compared to day/night cycles (3.7% CDW). In addition to PHB content, glycogen and cell size increased, while cell density and cell viability decreased. The results offer new approaches for further studies to gain deeper insights into the role of PHB in cyanobacteria to obtain bioplastics in a more sustainable and environmentally friendly way.

Extraction, structural characterization, and antioxidant activity of polysaccharides from three microalgae

Microalgal polysaccharides have received much attention due to their potential value in preventing and regulating oxidative damage. This study aims to reveal the mechanisms of regulating oxidative stress and the differences in the yield, structure, and effect of polysaccharides extracted from three microalgae: Golenkinia sp. polysaccharides (GPS), Chlorella sorokiniana polysaccharides (CPS), and Spirulina subsalsa polysaccharides (SPS). Using the same extraction method, GPS, CPS, and SPS were all heteropoly- saccharides composed of small molecular fraction: the monosaccharides mainly comprised galactose (Gal). Among the three, SPS had a higher proportion of small molecular fraction, and a higher proportion of Gal; thus it had the highest yield and antioxidant activity. GPS, CPS, and SPS all showed strong antioxidant activity in vitro, and showed strong ability to regulate oxidative stress, among which SPS was slightly higher. From the analysis of gene expression, the Nrf2-ARE signalling pathway was an important pathway for GPS, CPS, and SPS to regulate cellular oxidative stress. This study provides a theoretical foundation for further research on the utilization of microalgae polysaccharides and product development.

Metabolomics Reveals the Impact of Overexpression of Cytosolic Fructose-1,6-Bisphosphatase on Photosynthesis and Growth in Nannochloropsis gaditana

Nannochloropsis gaditana, a microalga known for its photosynthetic efficiency, serves as a cell factory, producing valuable biomolecules such as proteins, lipids, and pigments. These components make it an ideal candidate for biofuel production and pharmaceutical applications. In this study, we genetically engineered N. gaditana to overexpress the enzyme fructose-1,6-bisphosphatase (cyFBPase) using the Hsp promoter, aiming to enhance sugar metabolism and biomass accumulation. The modified algal strain, termed NgFBP, exhibited a 1.34-fold increase in cyFBPase activity under photoautotrophic conditions. This modification led to a doubling of biomass production and an increase in eicosapentaenoic acid (EPA) content in fatty acids to 20.78-23.08%. Additionally, the genetic alteration activated the pathways related to glycine, protoporphyrin, thioglucosides, pantothenic acid, CoA, and glycerophospholipids. This shift in carbon allocation towards chloroplast development significantly enhanced photosynthesis and growth. The outcomes of this study not only improve our understanding of photosynthesis and carbon allocation in N. gaditana but also suggest new biotechnological methods to optimize biomass yield and compound production in microalgae.

The Role of Light on the Microalgae Biotechnology: Fundamentals, Technological Approaches, and Sustainability Issues

Light energy directly affects microalgae growth and productivity. Microalgae in natural environments receive light through solar fluxes, and their duration and distribution are highly variable over time. Consequently, microalgae must adjust their photosynthetic processes to avoid photo limitation and photoinhibition and maximize yield. Considering these circumstances, adjusting light capture through artificial lighting in the main culture systems benefits microalgae growth and induces the production of commercially important compounds. In this sense, this review provides a comprehensive study of the role of light in microalgae biotechnology. For this, we present the main fundamentals and reactions of metabolism and metabolic alternatives to regulate photosynthetic conversion in microalgae cells. Light conversions based on natural and artificial systems are compared, mainly demonstrating the impact of solar radiation on natural systems and lighting devices, spectral compositions, periodic modulations, and light fluxes when using artificial lighting systems. The most commonly used photobioreactor design and performance are shown herein, in addition to a more detailed discussion of light-dependent approaches in these photobioreactors. In addition, we present the principal advances in photobioreactor projects, focusing on lighting, through a patent-based analysis to map technological trends. Lastly, sustainability and economic issues in commercializing microalgae products were presented.

Impact of 3D printing materials on mircoalga Chlorella vulgaris

3D printing represents a key enabling technology in designing photobioreactors. It allows rapid prototyping of complex geometries at an affordable price. Yet, no study dealt with the biocompatibility of 3D printing material with microalgae. Thus microalga Chlorella vulgaris was cultivated in contact with different 3D printing materials (Acrylonitrile Butadiene Styren - ABS, PolyCarbonate Blend - PC-Blend, PolyLactic acid - PLA, and acrylate methacrylate resin). Cell status was analyzed using flow cytometry, fluorometry, and pigment profiling. Results revealed that acrylate methacrylate resin material inhibits growth, a constant rise in intracellular reactive oxygen species, and a decrease in photosynthetic apparatus functioning. On the contrary, ABS, PC-Blend, and PLA led to nominal perfromances. Nevertheless, PLA was the only material that did not induce an early onset of intracellular reactive oxygen species. Therefore, resin can be ruled out as photobioreactor material, ABS and PC-Blend could be used after a curation period, and PLA induces no detectable perturbations by the means used in this study.

A precise microalgae farming for CO2 sequestration: A critical review and perspectives

Microalgae are great candidates for CO2 sequestration and sustainable production of food, feed, fuels and biochemicals. Light intensity, temperature, carbon supply, and cell physiological state are key factors of photosynthesis, and efficient phototrophic production of microalgal biomass occurs only when all these factors are in their optimal range simultaneously. However, this synergistic state is often not achievable due to the ever-changing environmental factors such as sunlight and temperature, which results in serious waste of sunlight energy and other resources, ultimately leading to high production costs. Most control strategies developed thus far in the bioengineering field actually aim to improve heterotrophic processes, but phototrophic processes face a completely different problem. Hence, an alternative control strategy needs to be developed, and precise microalgal cultivation is a promising strategy in which the production resources are precisely supplied according to the dynamic changes in key factors such as sunlight and temperature. In this work, the development and recent progress of precise microalgal phototrophic cultivation are reviewed. The key environmental and cultivation factors and their dynamic effects on microalgal cultivation are analyzed, including microalgal growth, cultivation costs and energy inputs. Future research for the development of more precise microalgae farming is discussed. This study provides new insight into developing cost-effective and efficient microalgae farming for CO2 sequestration.

Enhanced Photosynthetic Pigment Production Using a Scaled-Up Continuously Circulated Bioreactor

Microalgae have gained attention as a promising source of chlorophylls and carotenoids in various industries. However, scaling up of conventional bubble columns presents challenges related to cell sedimentation and the presence of non-photosynthetic cells due to non-circulating zones and decreased light accessibility, respectively. Therefore, this study aimed to evaluate the newly developed continuously circulated bioreactor ROSEMAX at both laboratory and pilot scales, compared to a conventional bubble column. There was no significant difference in the biomass production and photosynthetic pigment content of Tetraselmis sp. cultivated at the laboratory scale (p > 0.05). However, at the pilot scale, the biomass cultured in ROSEMAX showed significantly high biomass (1.69 ± 0.11 g/L, dry weight, DW), chlorophyll-a (14.60 ± 0.76 mg/g, DW), and total carotene (5.64 ± 0.81 mg/g, DW) concentrations compared to the conventional bubble column (1.17 ± 0.11 g/L, DW, 10.67 ± 0.72 mg/g, DW, 3.21 ± 0.56 mg/g, DW, respectively) (p ≤ 0.05). Flow cytometric analyses confirmed that the proportion of Tetraselmis sp. live cells in the culture medium of ROSEMAX was 32.90% higher than that in the conventional bubble column, with a photosynthetic efficiency 1.14 times higher. These results support suggestions to use ROSEMAX as a bioreactor for industrial-scale applications.

Necessity of stirring for outdoor microalgal-bacterial granular sludge process

As a green process, microalgal-bacterial granular sludge (MBGS) process shows talents in achieving pollutant removal, resource recovery and carbon neutralization. However, when it comes to application, the adequate mixing of MBGS and substrate should be adopted theoretically. Therefore, this study devoted to address the necessity of stirring for MBGS in municipal wastewater treatment. Outdoor performances showed that stirring significantly enhanced both of the photosynthetic efficiency and biomass productivity of MBGS with almost 2-fold increase as compared to non-stirred MBGS, while the average pore size and microalgae-to-bacteria ratio also increased. Consequently, stirring acted as a pivotal role in accelerating pollutants removal, with removals of organics (89.89% COD) and nutrients (99.22% NH4+-N, 92.15% PO43--P) reaching peak levels at 2 h and 6 h, respectively, while removals of organics (87.50% COD) and nutrients (86.11% NH4+-N, 86.76% PO43--P) removal peaked at 8 h for non-stirred MBGS. The improved granule characteristics and microbial compositions due to the stirring were found to be favorable for MBGS to adapting to the changeable weather. Based on the above results, the possible underlying mechanisms of stirring for improving MBGS were illustrated. Overall, stirring positively impacted the photosynthetic efficiency, biomass productivity, pollutant removal and microbial structure for MBGS. This study gains knowledge on stirred MBGS process under outdoor conditions for its future practical application.

Design a novel internally illuminated mirror photobioreactor to improve microalgae production through homogeneous light distribution

In this study, a novel internally illuminated mirror photobioreactor (IIM-PBR) was designed to improve microalgae biomass production through providing a homogenous light distribution in cultivation medium. The performance of the IIM-PBR was compared with internally illuminated control photobioreactor (IIC-PBR) and externally illuminated control photobioreactor (EIC-PBR) in terms of cell growth, wastewater treatment and bioproducts generation. Compared with the IIC-PBR and EIC-PBR, the IIM-PBR increased microalgae growth rate up to 60 % and 30%, respectively. Municipal wastewater treatment revealed that the IIM-PBR could significantly improve nutrients removal as the final removal efficiencies of 90%, 95% and 90% were obtained for nitrate, phosphate and COD, respectively. Moreover, the IIM-PBR increased the total bioproducts production by 89% and 46% compared to in the IIC-PBR and EIC-PBR, respectively. Based on the energy consumption calculation, the mirror's light-reflective properties of the IIM-PBR resulted in a significant reduction of total energy consumption (∼10 times).

The impact of light/dark regimes on structure and physiology of Chlorella vulgaris biofilms

Introduction

Biofilm-based microalgae production technologies offer enormous potential for improving sustainability and productivity. However, the light pattern induced by these technologies is a key concern for optimization.

Methods

In this work, the effects of light/dark cycles on architecture, growth, and physiology of Chlorella vulgaris biofilms were assessed in a millifluidic flow-cell with different time cycles (15 s to 3 min) keeping the average light constant at 100 μmol·m-2·s-1.

Results and discussion

Results showed that photoinhibition can be mitigated by applying a light fraction of 1/3 and a cycle time of 15 s. By contrast, when the cycle time is extended to 90 s and 3 min, photoinhibition is high and photoefficiency dramatically decreases. To cope with light stress, cells acclimate and organize themselves differently in space. A high peak light (500 μmol·m-2·s-1) triggers a stress, reducing cell division and inducing clusters in the biofilm. This work provides guidelines for optimizing rotating microalgae production systems in biofilms and assesses the minimum rotating frequency required to maintain the net growth rate close to that of continuous light of the same average intensity, mitigating photo-inhibition. The overall gain in productivity is then provided by the total surface of the biofilm turning in the illuminated surface area.

Effect of Photoperiod and White LED on Biomass Growth and Protein Production by Spirulina

The constant increase in demand for food, valued bio-based compounds and energy demand has prompted the development of innovative and sustainable resources. New technologies and strategies must be implemented to boost microalgae biomass production, such as using different photoperiods along with (LED) light-emitting diodes to stimulate biomass production and boost profits. This work investigates the cultivation of blue-green microalgae (Spirulina) in a closed lab condition. The current study aims to boost Spirulina biomass production by creating ideal growth conditions using different photoperiods (12:12; 10:14; 14:10) light/dark with a constant light intensity of 2000 lx from White LED lights. The obtained optical density and protein content was highest for photoperiod 14L: 10D and values were 0.280 OD, with a protein content of 23.44 g/100 g, respectively. This study is a crucial first step in identifying the best photoperiod conditions to help S. platensis produce more biomass. The study results showed that increasing photoperiod for S. platensis farming can improve the quality and amount of biomass generated in those cultures without negatively affecting growth.

Effect of light fluctuations on photosynthesis and metabolic flux in Synechocystis sp. PCC 6803

In nature, photosynthetic organisms are exposed to fluctuating light, and their physiological systems must adapt to this fluctuation. To maintain homeostasis, these organisms have a light fluctuation photoprotective mechanism, which functions in both photosystems and metabolism. Although the photoprotective mechanisms functioning in the photosystem have been studied, it is unclear how metabolism responds to light fluctuations within a few seconds. In the present study, we investigated the metabolic response of Synechocystis sp. PCC 6803 to light fluctuations using 13 C-metabolic flux analysis. The light intensity and duty ratio were adjusted such that the total number of photons or the light intensity during the low-light phase was equal. Light fluctuations affected cell growth and photosynthetic activity under the experimental conditions. However, metabolic flux distributions and cofactor production rates were not affected by the light fluctuations. Furthermore, the estimated ATP and NADPH production rates in the photosystems suggest that NADPH-consuming electron dissipation occurs under fluctuating light conditions. Although we focused on the water-water cycle as the electron dissipation path, no growth effect was observed in an flv3-disrupted strain under fluctuating light, suggesting that another path contributes to electron dissipation under these conditions.

Irradiance penetration distribution and flashing light frequency simultaneously affected with microalgal cell absorption and CO2 bubble scattering in a raceway pond

In order to investigate light penetration and flashing light frequency for microalgal cell-CO₂ bubble culture system in a raceway pond, user-defined function for CO₂ mass transfer and bubble scattering models coupled with discrete ordinates radiation model were adopted to clarify simultaneous effects of microalgal cell absorption and CO₂ bubble scattering. Light intensity along the microalgal suspension depth attenuated more rapidly with increased biomass concentration, decreased bubble generation diameter, increased CO₂ gas content and incident light intensity. Ratio of light zone decreased from 81.13 % to 20.00 % when biomass concentration increased from 0 to 0.4 g/L because of light absorption and shading effects of microalgae. When bubble generation diameter increased from 0.1 to 1.6 mm, ratio of light zone increased from 37.95 % to 42.64 %, while microalgal flashing light cycle first decreased to a valley of 1.81 s at 0.8 mm and then increased. Local light intensity in the upper layers was more enhanced due to lots of CO₂ bubbles gathering and reflecting more light with decreased bubble diameter and increased gas content. Light attenuated more rapidly in microalgal suspension with decreased bubble generation diameter and increased CO₂ gas content because of increased bubble diffraction coefficient and contact area. When initial CO₂ volume fraction increased from 0.02 to 0.2, flashing light frequency of microalgal cells decreased from 0.55 to 0.29 Hz and light zone time ratio φ decreased from 36.90 % to 18.40 %. At a biomass concentration of 0.1 g/L and a bubble flow rate of 0.1 m/s, the maximum light penetration and microalgal growth rate was achieved when bubble diameter, incident light intensity and gas content were optimally at 0.8 mm, 200 W/m² and 0.02, respectively. This work provides data support and theoretical guidance for photobioreactor design and optimization of light energy utilization.

Integrating wind-driven agitating blade into a floating photobioreactor to enhance fluid mixing and microalgae growth

Aiming at optimizing the poor fluid mixing state in the traditional horizontal floating photobioreactors and reducing the high energy consumption and operational cost induced by electric-driven mixing, a novel floating photobioreactor with an embedded wind-driven agitating blade (WDAB-FPBR) was proposed in this study, which can effectively utilize both wind and wave energy for fluid mixing. The results show that the selected wind-driven agitating blade contributed to a decrement of 75.3% in mixing time and an increment of 87.5% in mass transfer coefficient, and meanwhile strengthened the fluid velocity along the light gradient. Owing to the enhanced fluid flow and mixing properties, an even distribution of algae cells was achieved in the WDAB floating photobioreactor, which resulted in an improvement of 140% in the photosynthesis efficiency of microalgae. From this, the biomass yield and carbon removal ratio showed an increment of 88.9% and 73.9%, respectively.

Theoretical growth rate of microalgae under high/low-flashing light

Dynamic light regimes strongly impact microalgal photosynthesis efficiency. Finding the optimal way to supply light is then a tricky problem, especially when the growth rate is inhibited by overexposition to light and, at the same time, there is a lack of light in the deepest part of the culture. In this paper, we use the Han model to study the theoretical microalgal growth rate by applying periodically two different light intensities. Two approaches are considered depending on the period of the light pattern. For a large light period, we demonstrate that the average photosynthetic rate can be improved under some conditions. Moreover, we can also enhance the growth rate at steady state as given by the PI-curve. Although, these conditions change through the depth of a bioreactor. This theoretical improvement in the range of 10-15% is due to a recovery of photoinhibited cells during the high irradiance phase. We give a minimal value of the duty cycle for which the optimal irradiance is perceived by the algae culture under flashing light regime.

Pulsed-lighting LED luminaire for agriculture with a geometrical optical solution

Light-emitting diodes (LEDs) are the 4th plant supplemental lighting source. Pulsed lighting is benefit to increase energy utilization efficiency in greenhouse production. A pulsed-lighting LED luminaire with geometrical optical solution is proposed to overcome the shortcoming with pulse width modulation (PWM) solution. In addition, this luminaire also achieves uniform lighting by designing optical surfaces. In the illumination area, the lighting frequency is 117.6 Hz and the illuminance uniformity is 0.789, which is better than 0.75 (+/- 12.5%). In an actual planting experiment of Brassica chinensis, the average fresh weight of the plants under the pulsed-lighting LED luminaire was 33.1% higher than that under the conventional LED luminaire. The results showed that the energy utilization efficiency of the pulsed-lighting LED luminaire is 22.9% higher than that of the conventional LED luminaire.

Comparative life cycle assessment of conventional and novel microalgae production systems and environmental impact mitigation in urban-industrial symbiosis

The versatility of microalgae biomass as candidates for various products and bioremediation needs motivates interests towards design and implementation of novel microalgae bioreactors. Conventional open-reactors are reliant on large quantities of sunlight and space while yields are constrained by outdoor environment conditions. Conversely, closed-reactor systems like bubble columns reduces these constrains on microalgae growth while occupying far less space at the expense of high energy demands, notably from lighting systems. A novel patented closed reactor design has recently been proposed that improves the bubble column concept with an efficient and effective lighting system. The present study uses Life Cycle Assessment approach to compare the environmental performance of conventional reactors and the proposed internally luminated novel closed reactor design, expressing impacts per kg biostimulant for the Scenedesmus almeriensis harvest from such units. All performance data was collected from a pilot facility in Almeria, Spain. Urban-industrial symbiosis scenarios are also portrayed in the study using wastewater and incinerator flue gas. Results show that under synthetic nutrient and carbon inputs in Spanish pilot operations, the cumulative energy demand for the novel photobioreactors is similar to conventional vertically-stacked horizon bioreactors but are substantially more demanding than conventional open reactors. However, when leveraging renewable energy sources and the photosynthesis process to consume wastestreams in urban-industrial symbiosis scenarios, the novel photobioreactor was able to achieve up to 80 % improvements in several impact categories e.g. eutrophication and climate change. Impact mitigation credits per kg dwt biomass across all energy scenarios in symbiosis amount to ≈1.8 kg CO2eq and ≈0.09 kg PO4 eq. This highlights that such closed and internally illuminated photobioreactors can be competitive with conventional reactors, and have potential to harness photosynthesis to reduce environmental burdens in an urban-industrial symbiosis setting. Possible economies of scale and the associated potential gains in efficiencies are further discussed.

Flashing lights affect the photophysiology and expression of carotenoid and lipid synthesis genes in Nannochloropsis gaditana

Nannochloropsis gaditana is a promising microalga for biotechnology. One of the strategies to stimulate its full potential in metabolite production is exposure to flashing lights. Here, we report how N. gaditana adapts to different flashing light regimes (5, 50, and 500 Hz) by changing its cellular physiology and the relative expression of genes related to critical cellular functions. We analyzed the differential mRNA abundance of genes related to photosynthesis, nitrogen assimilation and biosynthesis of chlorophyll, carotenoids, lipids, fatty acids and starch. Analysis of photosynthetic efficiency and high mRNA abundance of photoprotection genes supported the inference that excess excitation energy provided by light absorbance during photosynthesis was produced under low frequency flashing lights and was dissipated by photopigments via the xanthophyll-cycle. Increased relative expression levels of genes related to the synthesis of carotenoids and chlorophyll confirmed the accumulation of photopigments previously observed at low frequency flashing lights. Higher differential mRNA abundance of genes related to the triacylglycerol biosynthesis were observed at lower frequency flashing lights, possibly triggered by a poor nitrogen assimilation caused by low mRNA abundance of a nitrate reductase gene. This study advances a new understanding of algal physiology and metabolism leading to improved cellular performance and metabolite production.

Recent progress on converting CO2 into microalgal biomass using suspended photobioreactors

Inhomogeneous light distribution and poor CO₂ transfer capacity are two critical concerns impeding microalgal photosynthesis in practical suspended photobioreactors (PBRs). To provide valuable guidance on designing high-performance PBRs, recent progress on enhancing light and CO₂ availabilities is systematically summarized in this review. Particularly, for the first time, the strategies on elevating light availability are classified and discussed from the perspectives of increasing incident light intensity, introducing internal illumination, optimizing flow field, regulating biomass concentrations, and enlarging illumination surface areas. Meanwhile, the strategies on enhancing CO₂ light availability are outlined from the aspects of generating smaller bubbles, extending bubbles residence time, and facilitating CO₂ dissolution using extra additives. Given the microalgal biomass production using current PBRs are still suffering from low productivity and economic feasibility, the possible future directions for PBRs implementation and development are presented. Altogether, this review is beneficial to furthering development of PBRs as a practical technology.

CultureLED: A 3D printer-based LED illumination cultivation system for multi-well culture plates

Microalgae are a source of high value products such as pigments, lipids and carbohydrates. Microalgae cultivation techniques have evolved and improved, but a vast amount of research is still needed to achieve a better understanding of these microorganisms. Due to this, there is a growing need for affordable, flexible, and easy to control research systems and protocols. 3D printing revolutionized design and manufacturing as it became widely available to the mass market, allowing the creation of novel forms, enabling mass customization, and supporting low-volume, distributed production. The emergence of open-source designs combined with 3D printing applications have the potential to replace and outperform standard designs and methods. This protocol describes CultureLED, a well plated cell culture system that can be mounted on an orbital shaker or positioned on a shelf. It is an open hardware design, based on low-cost commercial off-the-shelf components. It was designed for optimized production cost, simplicity, low power consumption, design flexibility, and controllable light conditions. The CultureLED utilizes light-emitting diodes and it can be used for cultivation of small sized organisms or microorganisms with different light requirements and as such, has a wide range of applications.

Bioenergy, Biofuels, Lipids and Pigments—Research Trends in the Use of Microalgae Grown in Photobioreactors

This scientometric review and bibliometric analysis aimed to characterize trends in scientific research related to algae, photobioreactors and astaxanthin. Scientific articles published between 1995 and 2020 in the Web of Science and Scopus bibliographic databases were analyzed. The article presents the number of scientific articles in particular years and according to the publication type (e.g., articles, reviews and books). The most productive authors were selected in terms of the number of publications, the number of citations, the impact factor, affiliated research units and individual countries. Based on the number of keyword occurrences and a content analysis of 367 publications, seven leading areas of scientific interest (clusters) were identified: (1) techno-economic profitability of biofuels, bioenergy and pigment production in microalgae biorefineries, (2) the impact of the construction of photobioreactors and process parameters on the efficiency of microalgae cultivation, (3) strategies for increasing the amount of obtained lipids and obtaining biodiesel in Chlorella microalgae cultivation, (4) the production of astaxanthin on an industrial scale using Haematococcus microalgae, (5) the productivity of biomass and the use of alternative carbon sources in microalgae culture, (6) the effect of light and carbon dioxide conversion on biomass yield and (7) heterotrophy. Analysis revealed that topics closely related to bioenergy production and biofuels played a dominant role in scientific research. This publication indicates the directions and topics for future scientific research that should be carried out to successfully implement economically viable technology based on microalgae on an industrial scale.

Modeling and Simulation of Photobioreactors with Computational Fluid Dynamics—A Comprehensive Review

Computational Fluid Dynamics (CFD) have been frequently applied to model the growth conditions in photobioreactors, which are affected in a complex way by multiple, interacting physical processes. We review common photobioreactor types and discuss the processes occurring therein as well as how these processes have been considered in previous CFD models. The analysis reveals that CFD models of photobioreactors do often not consider state-of-the-art modeling approaches. As a comprehensive photobioreactor model consists of several sub-models, we review the most relevant models for the simulation of fluid flows, light propagation, heat and mass transfer and growth kinetics as well as state-of-the-art models for turbulence and interphase forces, revealing their strength and deficiencies. In addition, we review the population balance equation, breakage and coalescence models and discretization methods since the predicted bubble size distribution critically depends on them. This comprehensive overview of the available models provides a unique toolbox for generating CFD models of photobioreactors. Directions future research should take are also discussed, mainly consisting of an extensive experimental validation of the single models for specific photobioreactor geometries, as well as more complete and sophisticated integrated models by virtue of the constant increase of the computational capacity.

Ecological impacts of photosynthetic light harvesting in changing aquatic environments: A systematic literature map

Underwater light is spatially as well as temporally variable and directly affects phytoplankton growth and competition. Here we systematically (following the guidelines of PRISMA-EcoEvo) searched and screened the published literature resulting in 640 individual articles. We mapped the conducted research for the objectives of (1) phytoplankton fundamental responses to light, (2) effects of light on the competition between phytoplankton species, and (3) effects of climate-change-induced changes in the light availability in aquatic ecosystems. Among the fundamental responses of phytoplankton to light, the effects of light intensity (quantity, as measure of total photon or energy flux) were investigated in most identified studies. The effects of the light spectrum (quality) that via species-specific light absorbance result in direct consequences on species competition emerged more recently. Complexity in competition arises due to variability and fluctuations in light which effects are sparsely investigated on community level. Predictions regarding future climate change scenarios included changes in in stratification and mixing, lake and coastal ocean darkening, UV radiation, ice melting as well as light pollution which affect the underwater light-climate. Generalization of consequences is difficult due to a high variability, interactions of consequences as well as a lack in sustained timeseries and holistic approaches. Nevertheless, our systematic literature map, and the identified articles within, provide a comprehensive overview and shall guide prospective research.

Flashing light alleviates photoinhibition and promotes biomass concentration in purple non- sulfur bacteria wastewater treatment

High light is beneficial for purple non-sulfur bacteria (PNSB) growth. However, excessive light causes photoinhibition. In this novel study, flashing light was used to alleviate photoinhibition and promote biomass growth in PNSB wastewater treatment. Results showed that flashing light effectively increased biomass production. The highest biomass concentration (2688.8 mg/L) and chemical oxygen demand removal (in 177 μmol/m²/s-0.75 duty cycle-1000 Hz group) were 41.5% and 28.4% higher than that in the constant stress light group (same incident light). This group also increased biomass concentration by 21.3% and reduced energy consumption by 26.2% compared with the constant normal light group (same energy input). The shortened single light provision time of flashing light increased the relative electron transportation rate by 116.6%, avoiding photoinhibition, promoting energy utilisation, and enhancing substance synthesis. Flashing light can be used as a light regulation strategy to enhance biomass accumulation and reduce energy consumption in PNSB-based industries.

Microalgae Xanthophylls: From Biosynthesis Pathway and Production Techniques to Encapsulation Development

In the last 20 years, xanthophylls from microalgae have gained increased scientific and industrial interests. This review highlights the essential issues that concern this class of high value compounds. Firstly, their chemical diversity as the producer microorganisms was detailed. Then, the use of conventional and innovative extraction techniques was discussed. Upgraded knowledge on the biosynthetic pathway of the main xanthophylls produced by photosynthetic microorganisms was reviewed in depth, providing new insightful ideas, clarifying the function of these active biomolecules. In addition, the recent advances in encapsulation techniques of astaxanthin and fucoxanthin, such as spray and freeze drying, gelation, emulsification and coacervation were updated. Providing information about these topics and their applications and advances could be a help to students and young researchers who are interested in chemical and metabolic engineering, chemistry and natural products communities to approach the complex thematic of xanthophylls.

A review on the progress, challenges and prospects in commercializing microalgal fucoxanthin

Fucoxanthin, the most abundant but nearly untapped carotenoid resource, is in the spotlight in the last decade from various perspectives due to a wide range of bioactivities and healthy benefits. The exploitation of fucoxanthin for nutraceutical and pharmaceutical purposes encompasses enormous scientific and economic potentials. Traditional production of fucoxanthin from brown algae (macroalgae) is constrained by limited yield and prohibitively high cost. Microalgae, as the most diverse photoautotrophs, hold the promises as sustainable sources and ideal cell factories for commercial fucoxanthin production, owing to their rich fucoxanthin content and excellent biomass productivity. In this work, the recent progress in upstream (microalgae selection, optimization of culture conditions, trophic modes, cultivation strategies and biosynthesis pathway) as well as downstream processes (extraction) of fucoxanthin production has been comprehensively and critically reviewed. The major bottlenecks, such as screening of fucoxanthin-producers, conflict between biomass and fucoxanthin accumulation under high light condition, unclear steps in biosynthesis pathway and limited evaluation of outdoor scale-up cultivation and extraction, have been pinpointed. Most importantly, the applications of emerging and conventional techniques facilitating commercialization of microalgal fucoxanthin are highlighted. The reviewed and evaluated include breeding and high-throughput screening methods of elite strains; flashing light effect inducing concurrent biomass and fucoxanthin accumulation; fucoxanthin biosynthesis and the regulatory mechanisms associating with its accumulation elucidated with the development of genetic engineering and omics techniques; and photobioreactors, harvesting and extraction techniques suitable for scaling up fucoxanthin production. In conclusion, the prospects of microalgal fucoxanthin commercialization can be expected with the joint development of fundamental phycology and biotechnology.

Boosting photo-biochemical conversion and carbon dioxide bio-fixation of Chlorella vulgaris in an optimized photobioreactor with airfoil-shaped deflectors

Aiming at ameliorating the poor hydrodynamic regimes and uneven light distribution in the conventional airlift flat-plate photobioreactor (AFP-PBR), a novel PBR with static airfoil-shaped deflectors (ASD-PBR) is proposed in this study to boost the microalgal biomass manipulation and hence the photo-biochemical conversion. The ASD module accelerated the circulation of microalgal suspension from the center to two sides with the help of bubbling so that the microalgal cells got more opportunities to access the light source. Compared with the control PBR, the solution velocity along the incident light direction increased by 114.8% in the newly-proposed ASD-PBR. Furthermore, the ASD module also served as a static mixer, which resulted in an increment of 11.5% in mass transfer coefficient and a decrement of 21.4% in mixing time. The amended hydrodynamic characteristics eventually contributed to an improvement of 18.3% and 10.9% in the maximum algal biomass yield and CO₂ fixation rate, respectively.

Model-Based Prediction of Perceived Light Flashing in Recirculated Inclined Wavy-Bottomed Photobioreactors

Microalgae biomass production rate in short light-path photobioreactors potentially can be improved by mixing-induced flashing light regimes. A cascade photobioreactor features a thin liquid layer flowing down a sloping, wavy-bottomed surface where liquid flow exhibits peculiar local recirculation hydrodynamics, potentially conducive to an ordered flashing light regime. This article presents a model-based analysis of the frequency distribution of perceived irradiance in said wavy-bottomed photobioreactor. The model combines a Lagrangian description of the motion of individual cells, in turn derived from the hydrodynamic parameters of the photobioreactor extracted from an experimentally validated Computational Fluid Dynamic model, with a simplified description of the irradiance field across the culture thickness, down to the spectral analysis of perceived irradiance. The main finding of the work is that the wavy bottomed photobioreactor provides a ‘robust’ spectral excitation to the circulating microalgae up to 3 Hz frequency, while in flat panels and bubble columns excitation decays evenly at a 24 db/octave rate. This analysis paves the way to improving the light flashing performance of the wavy-bottomed photobioreactor with respect to geometry (cavity size and installation inclination) and operation (flow rate).

A New Shifting Strategy in Flashing Light Based on the Cell Growth Curve to Enhance β-carotene Biosynthesis in Dunaliella salina

Microalgae Dunaliella salina has been recognized as an effective source of β-carotene. To elevate the productivity of this species, light has been served as an important induction factor, in this regard, a new idea was inspired as designing a red-to-blue wavelength shifting system based on the growth rate and cell behavior. A photobioreactor was exposed to two panels of flashing red and blue LEDs. At the commencement of the stationary phase, the wavelength shifting was applied and red LEDs were replaced with blue ones. Maximum β-carotene content of 10 mg.g^-1 was obtained; at least 300% higher than the content in the controlled system (flashing red and blue light to the end of growth).

Photobiological Effects on Biochemical Composition in Porphyridium cruentum (Rhodophyta) with a Biotechnological Application

This study describes the relation of photosynthetic capacity, growth and biochemical compounds in the microalgae Porphyridium cruentum under saturated irradiance (200 μmol m^-2  s^-1 ) by white light (WL) and low-pressure sodium vapor lamps (SOX lamps-control) and supplemented by fluorescent lamps (FLs) with different light qualities (blue: λ_max = 440 nm; green: λ_max = 560 nm; and red: λ_max = 660 nm). The maximum photosynthetic efficiency (F_v / F_m ) showed a positive correlation with the light quality by saturating light SOX in mixture with stimulating blue light than the white light (WL) at the harvest day (10 days). The production, that is maximal electron transport rate (ETR_max ), and energy dissipation, that is maximal nonphotochemical quenching (NPQ_max ), had the same pattern throughout the time (3-6 days) being the values higher under white light (WL) compared with SOX and SOX plus supplemented different light qualities. Total protein levels increased significantly in the presence of SOX light, while phycoerythrin (B-PE) showed significant differences under SOX+ blue light. Arachidonic acid (ARA) was higher under SOX and SOX plus supplemented different light qualities than that under WL, whereas eicosapentaenoic acid (EPA) was the reverse. The high photomorphogenic potential by SOX light shows promising application for microalgal biotechnology.

Optical Camera Communication as an Enabling Technology for Microalgae Cultivation

Optical Camera Communication (OCC) systems have a potential application in microalgae production plants. In this work, a proof-of-concept prototype consisting of an artificial lighting photobioreactor is proposed. This reactor optimises the culture's photosynthetic efficiency while transmitting on-off keying signals to a rolling-shutter camera. Upon reception, both signal decoding and biomass concentration sensing are performed simultaneously using image processing techniques. Moreover, the communication channel's theoretical modelling, the data rate system's performance, and the plant distribution requirements and restrictions for a production-scale facility are detailed. A case study is conducted to classify three different node arrangements in a real facility, considering node visibility, channel capacity, and space exploitation. Finally, several experiments comprising radiance evaluation and Signal-to-Noise Ratio (SNR) computation are performed at different angles of view in both indoor and outdoor environments. It is observed that the Lambertian-like emission patterns are affected by increasing concentrations, reducing the effective emission angles. Furthermore, significant differences in the SNR, up to 20 dB, perceived along the illuminated surface (centre versus border), gradually reduce as light is affected by greater dispersion. The experimental analysis in terms of scattering and selective wavelength attenuation for green (Arthrospira platensis) and brown (Rhodosorus marinus) microalgae species determines that the selected strain must be considered in the development of this system.

Reaching Natural Growth: The Significance of Light and Temperature Fluctuations in Plant Performance in Indoor Growth Facilities

Recommendations for near-natural plant growth under indoor conditions have been described without considering environmental fluctuations, which might have important consequences for researchers and plant producers when comparing results from indoor facilities with natural ecosystems or production. Previous authors proposed that differences in temperature, light quantity, and the lack of their variation are sources of deviations between indoor and outdoor experiments. Here, we investigated the effect of fluctuating light, temperature, and humidity in an indoor environment on plant performance. Seven plant species from different functional plant types were grown outdoors during summer and spring. The same species were then grown in indoor growth chambers under different scenarios of climate complexity in terms of fluctuations of temperature, air humidity, and light: 1) fixed night and day conditions, 2) daily sinusoidal changes, and 3) variable conditions tracking the climate records from the field trials. In each scenario, the average of the environmental variables was the same as in the respective field trial. Productivity-, gas exchange-, and leaf pigment-traits were measured in all plants at the end of the experiments. The plant trait responses were highly dependent on species and treatment, but general trends were observed. The variable condition yielded lower biomass compared to the fixed and sinusoidal conditions, together with a higher specific leaf area and increased chlorophyll concentrations. A principal component analysis (PCA) across all plant traits in response to climatic conditions suggested that at least a sinusoidal fluctuation is recommended for a more natural-like plant performance in indoor growth facilities. However, prevailing significant differences for several traits between field- and indoor-grown plants even under variable climates indicate that additional factors other than those controllable in standard phytotrons (e.g., wind speed and direction, leaf and soil temperature) can still significantly bias plant performance in indoor facilities.

Multiscale numerical workflow describing microalgae motion and light pattern incidence towards population growth in a photobioreactor

In this article, a numerical workflow describing the microalgal growth inside of a photobioreactor is proposed. CFD is used to compute reactor internal hydrodynamics taking into account marine impeller rotation and sparged bubbles motion. Lagrangian approach is used to track microalgae motion inside of the culture vessel. The illumination across the reactor is obtained using the classical Beer-Lambert's law. The combination of light field and cell motion allows to reconstruct the light history of each microalgae. These histories are then supplied to Han's model which predicts individual growth rate and experienced photodamages. Once computed, several thousands of trajectories are agglomerated at the population level yielding the photobioreactor performances. After having ensured properties convergence, this procedure is applied to a large range of optical density (0 to 4.0), i.e. cell concentration, and incident light intensities (0 to 2000 μmolPhoton/m2/s). From this exploration, it is possible to determine the photobioreactor response surfaces in terms of growth rate and photodamages. These are latter used to propose an optimal lighting strategy for biomass production - reducing photobioreactor operation time by 16% compared to classical two-step procedure - and assist light induced stress with the aim of triggering secondary metabolites production.

Recent advances in downstream processing of microalgae lipid recovery for biofuel production

The world energy system faces two major challenges: the requirement for more energy and less carbon. It is important to address biofuels production as an alternative to the usage of fossil fuel by utilizing microalgae as the potential feedstock. Yet, the commercialization of microalgae remains contentious caused by factors relating to the life cycle assessment and feasibility of microalgae-based biofuels. This present review starts with an introduction to the benefits of microalgae, followed by intensive elaboration on microalgae cultivation parameters. Subsequently, the fundamental principle along with the advantages and disadvantages of various pretreatment techniques of microalgae were reviewed. In addition, the conventional and recent advances in lipid extraction techniques from microalgae were comprehensively evaluated. Comparative analysis regard to the gaps from previous studies was discussed point-by-point in each section. The effort presented in this review will provide an insight for future researches dealing with microalgae-biofuel production on downstream processing.

Biocompatible liquid-type carbon nanodots (C-paints) as light delivery materials for cell growth and astaxanthin induction of Haematococcus pluvialis

In this study, we aimed to demonstrate the feasibility of the application of biocompatible liquid type fluorescent carbon nanodots (C-paints) to microalgae by improving microalgae productivity. C-paints were prepared by a simple process of ultrasound irradiation using polyethylene glycol (PEG) as a passivation agent. The resulting C-paints exhibited a carbonyl-rich surface with good uniformity of particle size, excellent water solubility, photo-stability, fluorescence efficiency, and good biocompatibility (<10.0 mg mL^-1 of C-paints concentration). In the practical application of C-paints to microalgae culture, the most effective and optimized condition leading to growth promoting effect was observed at a C-paints concentration of 1.0 mg mL^-1 (>20% higher than the control cell content). A C-paints concentration of 1-10.0 mg mL^-1 induced an approximately >1.8 times higher astaxanthin content than the control cells. The high light delivery effect of non-cytotoxic C-paints was applied as a stress condition for H. pluvialis growth and was found to play a major role in enhancing productivity. Notably, the results from this study are an essential approach to improve astaxanthin production, which can be used in various applications because of its therapeutic effects such as cancer prevention, anti-inflammation, immune stimulation, and treatment of muscle-soreness.