Structure and properties of urea-plasticized starch films with different urea contents

Exploring urea as a prospective auxiliary for starch functionalization: A concise review on modified starch properties and the sustainable packaging films

Urea is also known as carbamide, an inexpensive and eco-friendly additive for starch functionalization. This article reviews the potential role of urea in starch modification, with the prominence of the mechanism of urea action, alterations in the starch structure and functional properties. In addition, current literature conveys the prospective effect of urea in fabricating starch films for food packaging, and the relevant areas that need to be covered in the forthcoming research are specified at the end of the article section. Urea can modify the diverse physico-chemical and functional properties of starch. Starch-based films exhibit pronounced effects on their mechanical and barrier properties upon the incorporation of urea, although this effect strongly depends on the urea content and degree of substitution (DS). Overall, urea holds great potential for use in the starch and bioplastic film industries, as it produces biocompatible derivatives with desirable performance.

Development of biodegradable film from cactus (Opuntia Ficus Indica) mucilage loaded with acid-leached kaolin as filler

Nowadays, substituting petroleum-based plastics with biodegradable polymers made from polysaccharides loaded with various reinforcing materials has recently gained attention due to the impact of conventional plastics wastes. In this study, polysaccharidic mucilage from Ethiopian cactus (Opuntia Ficus Indica) was derived using microwave-assisted extraction technique to develop biodegradable polymers that were inexpensive, readily available, simple to make, and ecofriendly. The effect of microwave power 300-800 W, solid-liquid (cactus-sodium hydroxide solution) ratio 1:5-1:25, sodium hydroxide concentration 0.1-0.8 mol/L, and extraction time 2-10 min on mucilage extraction were studied and the maximum yield of mucilage was attained at optimized parameters of 506 W, 1:20, 0.606 mol/L, and 9.5 min, respectively. Biodegradable polymers made with mucilage alone have poor mechanical characteristics and are thermally unstable. Thus, to overcome the stated problems, glycerol as a plasticizer and acid-leached kaolin crosslinked with urea as a reinforcing material were used. Moreover, the effect of acid-leached kaolin and glycerol on the physico-chemical properties of the films was studied, and a maximum tensile strength of 6.74 MPa with 18.45 % elongation at break, thermally improved biodegradability of 26 %, were attained at 10 % acid-leached kaolin and 20 % glycerol crosslinking with 2 % urea. But the maximum degradability of 53.5 % was attained at 30 % glycerol content. The control and reinforced biodegradable films were characterized using TGA, FTIR, SEM, and XRD to determine the thermal, functional group, morphology, and crystallinity of the bioplastics, respectively. These biodegradable plastics may be used for packaging application.

Anti-plasticizing effect of water on prilocaine and lidocaine - the role of the hydrogen bonding pattern

It is generally accepted that water, as an effective plasticizer, decreases the glass transition temperatures (Tgs) of amorphous drugs, potentially resulting in physical instabilities. However, recent studies suggest that water can also increase the Tgs of the amorphous forms of the drugs prilocaine (PRL) and lidocaine (LID), thus acting as an anti-plasticizer. To further understand the nature of the anti-plasticizing effect of water, interactions with different solvents and the resulting structural features of PRL and LID were investigated by Fourier transform infrared spectroscopy (FTIR) and quantum chemical simulations. Heavy water (deuterium oxides) was chosen as a solvent, as the deuterium and hydrogen atoms are electronically identical. It was found that substituting hydrogen with deuterium showed a minimal impact on the anti-plasticization of water on PRL. Ethanol and ethylene glycol were chosen as solvents to compare the hydrogen bonding patterns occurring between the hydroxyl groups of the solvents and PRL and LID. Comparison of the various Tgs showed a weaker anti-plasticizing potential of these two solvents on PRL and LID. The frequency shifts of the amide CO groups of PRL and LID due to the interactions with water, heavy water, ethanol, and ethylene glycol as observed in the FTIR spectra showed a correlation with the binding energies calculated by quantum chemical simulations. Overall, this study showed that the combination of weak hydrogen bonding and strong electrostatic contributions in hydrated PRL and LID could play an important role in inducing the anti-plasticizing effect of water on those drugs.

Treatment and mechanism for hot melting starch by reducing the molecular chain winding and crystallinity

Unlike thermoplastic petroleum-based materials, starch-based materials rely on aqueous systems but are incapable of hot melting, resulting in low processing efficiency and limited large-scale industrial applications. In this study, the combination of α-amylase liquefaction and urea plasticization was used for the first time to obtain enzymatic thermoplastic starch (ETPS) for hot melting by changing the molecular chain of starch. ETPS showed an apparent hot melting phenomenon when heated below 200 °C. Differential scanning calorimetry revealed that heat absorption peaks were obviously reduced, and the hot melting phenomenon occurred easily depending on the combination of enzymatic hydrolysis and plasticization. Dynamic mechanical analysis indicated that the combined modification effectively increased the number of freely movable chains. The red shift of -OH stretching vibration peaks indicated the formation of strengthened hydrogen bonds in ETPS. X-ray diffraction showed that the crystallinity of ETPS was reduced to 5.68 %, effectively reducing the regenerative phenomenon. Gel permeation chromatography revealed that the molecular weight of ETPS decreased, and the entanglements between molecular chains were reduced. A tensile test showed that the elongation at break of ETPS was as high as 235.29 %, which was much higher than those of enzymatic hydrolysis starch and thermoplastic starch.

From micro to macro: Physical-chemical characterization of wheat starch-based films modified with PEG200, sodium citrate, or citric acid

Needing to extend the shelf-life of packaged food and the evolving consumer demands led researchers to seek innovative, eco-friendly, and biocompatible packaging solutions. Starch is among the most promising natural and renewable alternatives to non-degradable plastics. Here, we deeply study the structural features of starch films modified by adding citric acid (CA) or sodium citrate (SC) as a cross-linker and polyethylene glycol 200 (PEG200) as a plasticizer and obtained through solvent casting. The substances' influence on starch films was evaluated through Attenuated Total Reflection Fourier Transform Infrared (ATR-FTIR) and Solid-state Nuclear Magnetic Resonance (ss-NMR) spectroscopies. Films' macroscopic properties, such as swelling index, solubility, thermo-mechanical features, and moisture absorption, were also assessed to foresee potential applications. Proper amounts of CA, CS, and PEG200 improve film properties and inhibit starch chains' retrogradation and recrystallization. Besides, the chemical neighbourhood of nuclei observed through ss-NMR significantly changed alongside the polymer chains' mobility. The latter result indicates a different polymer chain structural organization that could justify the film's higher resistance to thermal degradation and elongation at the break. This methodological approach is effective in predicting the macroscopic behaviour of a polymeric material and could be helpful for the application of such products in food preservation.

Effects of polyols with different hydroxyl numbers on the structure and properties of starch straws

To study the relationship between the number of hydroxyl groups of polyols and the plasticizing effect, the effects of different polyols including ethylene glycol, glycerol, erythritol, xylitol and sorbitol on the structure and properties of corn starch straws were analyzed and compared. The results showed that the addition of plasticizer significantly improved the performance of starch straws, which greatly improved the mechanical properties, water absorption rate (WAR) and thermal stability. However, there was no linear relationship between the plasticizing effect on starch straws and the number of hydroxyl groups in plasticizers. Fourier transform infrared (FTIR) results showed that erythritol formed the strongest intermolecular interaction with starch. Starch straws with erythritol (S-ERY) had the highest bending force (Fb = 25.78 N) and the lowest WAR. Starch straws with glycerol (S-GLY) showed the lowest relative crystallinity (RC = 12.87 %) and the highest temperature of the maximum degradation (Tdmax = 302.1 °C). In addition, after storing for 180 days, S-GLY showed higher modulus of elasticity in bending (Eb = 4.26 N/cm) and a uniform surface.

Thermoplastic starch (TPS)-based composite films for wastewater treatment: synthesis and fundamental characterization

Modification of starch is a potential basic research aiming to improve its water barrier properties. The general purpose of this study is to manufacture cross-linked iodinated starch citrate (ISC) with a degree of substitution (DS) ≈ 0.1 by modifying native corn starch with citric acid in the presence of iodine as an oxidizing agent. Thermoplastic starch (TPS) was generated with urea as a plasticizer and blended with various concentrations of ISC of (2, 4, 6%) (wt/wt) to obtain (UTPS/ISC₂, UTPS/ISC₄, and UTPS/ISC₆). Nanocomposite film was formed from UTPS/ISC₂ in presence of stabilized iodinated cellulose nanocrystals UTPS/ISC₂/SICNCs via gelatinization at a temperature of 80ºC. Water solubility and water vapor release were studied amongst the water barrier features. The fabricated starch-based composite films were evaluated utilizing Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electronic Microscope analysis (SEM), surface area, and tensile measurements. The adsorption of crystal violet (CV) dye onto produced samples was examined in an aqueous solution. The findings revealed that the UTPS/ISC₂/ISCNCs has 83% crystal violet elimination effectiveness. Moreover, the adsorption isotherms were assessed and figured out to vary in the order of Langmuir > Temkin > Freundlich > Dubinin-Radushkevich.

Study on Physicochemical Properties of Biocomposite Films with Spent Coffee Grounds as a Filler and Their Influence on Physiological State of Growing Plants

The aim of the study was to plasticize corn starch with two selected urea (U)-rich plasticizers: choline chloride (CC):U or betaine (B):U eutectic mixtures at a molar ratio of 1:5 with a presence of spent coffee grounds as a filler. The biomaterials were prepared via a solventless one-step extrusion method and then extrudates were thermoformed using compression molding into sheets. The materials were characterized using mechanical and sorption tests, TGA, DMTA and FTIR. Additionally, a study on the biodegradation and remaining nitrogen content in soil was conducted. For the first time, an influence on physiological state of growing plants of the materials presence in soil was investigated. The addition of the coffee filler slightly increased the mechanical properties and decreased the swelling degree of the materials. The DMTA results indicated that biocomposites were easily thermoformable and the high filler addition (20 pph per polymer matrix) did not affect the processability. According to the biodegradation test results, the materials disappeared in soil within ca. 70 days. The results from this study on the physiological state of growing plants revealed that the materials, especially plasticized with CCU, did not exhibit any toxic effect on the yellow dwarf bean. The percentage of total nitrogen in the soil substrate in comparison with the control increased indicating an effective release of nitrogen from the TPS materials into the substrate.

Thermal, Morphological and Mechanical Properties of a BioPE Matrix Composite: Case of Shell, Pulp, and Argan Cake as Biofillers

Extrusion and hot compressing molding processes were used to create bio-polyethylene (BioPE) composites reinforced with argan byproducts (shell, pulp, and argan cake) as bio-fillers. The thermal stability of the composites wass analyzed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Dynamical mechanical analysis and rheological testing were used to investigate their mechanical properties. The morphological results showed a good adhesion between the argan and BioPE matrix. More efficient mechanical properties have been distinguished in the case of argan byproduct-based composite. A higher Young's modulus was noted for all the biocomposites compared to pure BioPE. Thermal analysis revealed that the addition of bio-filler to polymer reduced decomposition temperatures. This study provides an ecological alternative for upgrading the valorization of abundant and underutilized Moroccan biomass. Furthermore, the possibility of using argan byproducts in composite manufacturing will help open up new markets for what is currently considered waste.

Deep Eutectic Solvents for Biotechnology Applications

Deep eutectic solvents (DESs) are an alternative to traditional organic solvents and ionic liquids and meet the requirements of "green" chemistry. They are easy to prepare using low-cost constituents, are non-toxic and biodegradable. The review analyzes literature on the use of DES in various fields of biotechnology, provides data on the types of DESs, methods for their preparation, and properties. The main areas of using DESs in biotechnology include extraction of physiologically active substances from natural resources, pretreatment of lignocellulosic biomass to improve enzymatic hydrolysis of cellulose, production of bioplastics, as well as a reaction medium for biocatalytic reactions. The aim of this review is to summarize available information on the use of new solvents for biotechnological purposes.

Using an enhanced multilayer model to analyze the performance of nickel alginate/graphene oxide aerogel, nickel alginate aerogel/activated carbon, and activated carbon in the adsorption of a textile dye pollutant

This work describes the modeling and analysis of methylene blue molecule on different adsorbents, namely, nickel alginate/graphene oxide (NA/GO) aerogel, nickel alginate/activated carbon (NA/AC) aerogel, and Trichosanthes kirilowii maxim shell activated carbon (TKAC). A multilayer statistical physics model was used to calculate the energetic and steric parameters of the adsorption of methylene blue on these adsorbents. Based on the modeling investigation, it was concluded that the formation of multiple dye adsorbed layers on these adsorbents could be feasible where physical adsorption interactions could be involved. Adsorption capacities at saturation of these adsorbents ranged from 542.97 to 470.03 mg/g, 790.66 to 684.47 mg/g, and 401.11 to 1236.24 mg/g for NA-GO aerogel, NA-AC aerogel, and TKAC, respectively. This research contributes with new findings for the understanding of dye adsorption on novel materials, which can be used in water pollution control.

Applications of Starch Biopolymers for a Sustainable Modern Agriculture

Protected cultivation in modern agriculture relies extensively on plastic-originated mulch films, nets, packaging, piping, silage, and various applications. Polyolefins synthesized from petrochemical routes are vastly consumed in plasticulture, wherein PP and PE are the dominant commodity plastics. Imposing substantial impacts on our geosphere and humankind, plastics in soil threaten food security, health, and the environment. Mismanaged plastics are not biodegradable under natural conditions and generate problematic emerging pollutants such as nano-micro plastics. Post-consumed petrochemical plastics from agriculture face many challenges in recycling and reusing due to soil contamination in fulfilling the zero waste hierarchy. Hence, biodegradable polymers from renewable sources for agricultural applications are pragmatic as mitigation. Starch is one of the most abundant biodegradable biopolymers from renewable sources; it also contains tunable thermoplastic properties suitable for diverse applications in agriculture. Functional performances of starch such as physicomechanical, barrier, and surface chemistry may be altered for extended agricultural applications. Furthermore, starch can be a multidimensional additive for plasticulture that can function as a filler, a metaphase component in blends/composites, a plasticizer, an efficient carrier for active delivery of biocides, etc. A substantial fraction of food and agricultural wastes and surpluses of starch sources are underutilized, without harnessing useful resources for agriscience. Hence, this review proposes reliable solutions from starch toward timely implementation of sustainable practices, circular economy, waste remediation, and green chemistry for plasticulture in agriscience

Effect of Kenaf Fibre as Reinforcing Fillers in Corn Starch-Based Biocomposite Film

Biocomposite films were prepared using corn starch (CS), sorbitol as a plasticiser, and multi-scale kenaf fibre as reinforcing filler. The microstructure and the physical, tensile, and water barrier properties of corn starch reinforced with kenaf fibre were characterised and investigated. The biocomposite films were developed via the solution casting technique using 10 g of CS with 0 to 8% kenaf fibre as filler treated with 30% (w/w, starch basis) of sorbitol. The increased amount of kenaf fibre introduced contributed to improvements in film thickness, weight, and density. Conversely, slight reductions in the biocomposite films’ moisture content, water absorption, and solubility rating were 9.86–5.88%, 163.13–114.68%, and 38.98–25.17%, respectively. An X-ray diffraction (XRD) test revealed that the films were amorphous and that there was no effect on the crystallinity structure of films with kenaf fibre reinforcement. Fourier transform infrared (FT-IR) and rheological analysis indicated that kenaf fibre could weaken the molecular interaction of the film matrix. Field emission scanning electron microscope (FESEM) revealed the arrangement and uniform distribution of kenaf fibre at 0.2–0.8%. The incorporation of kenaf increased the tensile strength, Young’s modulus, and elongation at break until (6% wt) of fibre. With the kenaf fibre incorporation, the optimal tensile strength, Young’s modulus, and elongation at break of the films reached 17.74 MPa, 1324.74 MPa, and 48.79%, respectively. Overall, the introduction of kenaf fibre as filler enhanced the physical and mechanical properties of CS films.

Biodegradable Thermoplastic Starch/Polycaprolactone Blends with Co-Continuous Morphology Suitable for Local Release of Antibiotics

We report a reproducible preparation and characterization of highly homogeneous thermoplastic starch/pol(ε‑caprolactone) blends (TPS/PCL) with a minimal thermomechanical degradation and co-continuous morphology. These materials would be suitable for biomedical applications, specifically for the local release of antibiotics (ATB) from the TPS phase. The TPS/PCL blends were prepared in the whole concentration range. In agreement with theoretical predictions based on component viscosities, the co-continuous morphology was found for TPS/PCL blends with a composition of 70/30 wt.%. The minimal thermomechanical degradation of the blends was achieved by an optimization of the processing conditions and by keeping processing temperatures as low as possible, because higher temperatures might damage ATB in the final application. The blends’ homogeneity was verified by scanning electron microscopy. The co-continuous morphology was confirmed by submicron-computed tomography. The mechanical performance of the blends was characterized in both microscale (by an instrumented microindentation hardness testing; MHI) and macroscale (by dynamic thermomechanical analysis; DMTA). The elastic moduli of TPS increased ca four times in the TPS/PCL (70/30) blend. The correlations between elastic moduli measured by MHI and DMTA were very strong, which implied that, in the future studies, it would be possible to use just micromechanical testing that does not require large specimens.

Deep Eutectic Solvents for Starch Treatment

In this review, the application of deep eutectic solvents (DESs) as starch solvents, plasticizers and for other treatment has been described. Starch, as one of the most abundant biopolymers, is considered for forming new biodegradable materials. This new approach, referring to applying deep eutectic solvents for dissolving starch, its plasticization and other modifications, was presented. A DES could be a good alternative for common starch plasticizers (e.g., glycerol, urea) as well as recently considered ionic liquids. The high variety of DES component combinations makes it possible to obtain materials with the properties specific for given applications.

Sustainable Bioactive Packaging Based on Thermoplastic Starch and Microalgae

This study combines the use of corn starch and Tetradesmus obliquus microalgae for the production of antioxidant starch films as flexible packaging material. Starch was plasticized with glycerol and blended with 1 w% polyallylamine chosen as an agent to modify the film physical properties. The addition of polyallylamine improved film water stability and water vapor transmission rate as well as mechanical stiffness and tenacity. The dried Tetradesmus obliquus microalgae, which showed an EC₅₀ value of 2.8 mg/mg DPPH (2.2-Diphenyl-1-picrylhydrazyl radical), was then used as antioxidant filler. The addition of microalgae provided the films with good antioxidant activity, which increased with microalgae content increasing. To our knowledge, this is the first study reporting the development of sustainable bioactive packaging films composed of almost 100% starch, and follows the European union's goals on plastics strategy concerning the promotion of bio-based, compostable plastics and the setting up of approaches to prevent food waste with a simple plastic packaging.

Starch phosphate carbamate hydrogel based slow-release urea formulation with good water retentivity

In this work, a novel starch phosphate carbamate hydrogel (SPC-Hydrogel) and its corresponding urea hydrogel (SPCU-Hydrogel) slow-release fertilizer (SRF) were prepared by one-step free radical copolymerization of SPC and acrylamide (AM) without and with urea addition. A series of characterization measurements including FTIR, XRD, EDS, XPS are utilized to confirm the successful formation of the SPC-Hydrogel. The SEM shows SPC-Hydrogel has a porous three-dimensional network architecture. Furthermore, SPC-Hydrogel matrix exhibits superior water absorbency achieving 80.2 g/g than that (70.5 g/g) of the native starch hydrogel (NS-Hydrogel) and desirable water retention capacity in soil with a weight loss of only 48% for 13 days. Compared with pure urea and NS based urea hydrogel (NSU-Hydrogel), the SPCU-Hydrogel releases 50.3% for 15 h, achieving an almost complete release more than 25 h in aqueous phase. While only 46.6% of urea is released in 20 days which extends about 30 days in soil column assays. The maize seedlings growth assays also present an intuitive evaluation on the prominent soil water holding and plant growth promotion role of SPCU-Hydrogel. In conclusion, the present work has demonstrated a novel strategy via preparing biomass hydrogel SRF to enhance the utilization effectiveness of fertilizer and retain soil humidity.

Characterization the structural property and degradation behavior of corn starch in KOH/thiourea aqueous solution

Finding an efficient and eco-friendly solution for starch dissolution has attracted considerable attentions in recent years. This study investigated the structural characteristics, and degradation behavior of corn starch in KOH/thiourea aqueous solution by the comparison with DMSO/LiBr and 1-allyl-3-methylimidazolium chloride (AMIMCl). Results showed that KOH/thiourea solution was an effective solvent for corn starch dissolution (30 min with 97.01% solubility). X-ray diffraction (XRD) and ¹³C CP-MAS NMR spectroscopy revealed that native crystallinity of the corn starch was altered by all tested solvents, especially DMSO/LiBr and AMIMCl. Conversely, this new solvent did not change the primary molecular structure, chain-length distribution, or thermal stability of starch, compared with the native starch. Furthermore, KOH/thiourea solution was more suitable for measuring the molecular weight of corn starch, with a weight-average molecular weight (M_w) of 7.18 × 10⁷ g/mol. Therefore, KOH/thiourea solution is a promising novel solvent for starch dissolution and structural exploration.

Development and Characterization of Cornstarch-Based Bioplastics Packaging Film Using a Combination of Different Plasticizers

This work aims to develop cornstarch (CS) based films using fructose (F), glycerol (G), and their combination (FG) as plasticizers with different ratios for food packaging applications. The findings showed that F-plasticized film had the lowest moisture content, highest crystallinity among all films, and exhibited the highest tensile strength and thermostability. In contrast, G-plasticized films showed the lowest density and water absorption with less crystallinity compared to the control and the other plasticized film. In addition, SEM results indicated that FG-plasticized films had a relatively smoother and more coherent surface among the tested films. The findings have also shown that varying the concentration of the plasticizers significantly affected the different properties of the plasticized films. Therefore, the selection of a suitable plasticizer at an appropriate concentration may significantly optimize film properties to promote the utilization of CS films for food packaging applications.

Freely Moldable Modified Starch as a Sustainable and Recyclable Plastic

Efficiently preparing a starch-based plastic with moisture insensitivity and toughness is a challenge to improve the high-value utilization of polysaccharide resources. Herein, a sustainable, recyclable starch-based plastic was prepared in a facile and eco-friendly way. First, starch acetoacetate (SAA) with different degrees of substitution (DSs) was synthesized by transesterification. Then, the SAA film was obtained through a solvent-free hot-pressing method. Notably, SAA with different DSs exhibited various glass transition temperatures (109-140 °C), and SAA with high DS (>0.84) was insoluble even after boiling in water for 1 h. Also, the maximum fracture strength of SAA film up to 15.5 MPa and a maximum elongation at break up to 30% were reached . In addition, the starch-based plastic film retained the original mechanical properties after three cycles of hot processing. In consideration of the facile preparation process, this protocol provided a new avenue for developing sustainable and recyclable starch-based plastics.

Deep eutectic solvents based on urea, polyols and sugars for starch treatment

Deep eutectic solvents (DES) based on urea (U), polyols (glycerol -G, sorbitol - S) and monosugars (glucose - Glu, fructose - Fru) were obtained, thermally characterized and used for potato starch treatment: dissolution and plasticization. The polysaccharide was dissolved in U/glycerol mixtures forming transparent, non-retrograded gels. The dissolution process was confirmed by microscopic observations and DSC analysis. Plasticizing efficiency of DES in thermoplasticized starch (TPS) via compression molding was investigated using mechanical tests, DMTA, XRD, TGA and FTIR analysis. Although all studied DES were able to plasticize starch effectively, the most flexible films were with urea/glycerol mixture: the highest elongation at break exceed 200%. XRD analysis confirmed high amorphization of starch with the urea-based DES after thermocompression. Moreover, introduction of urea as DES inhibited its recrystallization in the polysaccharide matrix.

Molecular Dispersion of Starch as a Crucial Parameter during Size-Exclusion Chromatography

Starch, α-polyglucan consisting of a large number of anhydroglucose units joined by α-1,4- and α-1,6-glycosidic bonds, seems to be characterized by a simple structure when compared to other natural polymers. Nevertheless, starches of various botanical origins have different physicochemical properties that are related to the differences in molecular and supramolecular structure of this polymer. In terms of the functional value of starch, the behavior of its macromolecules in solution is the most important result of its structural features. Extremely high molecular mass is the fundamental structural property of starch. Water, considered simply as a solvent for solubilization, does not provide molecular dispersion of starch without its degradation. The objectives of this study are to characterize the suitability of a new aqueous media (urea/NaOH) for enhancing the dispersion of native corn and potato starches and its effect on the consequent size-exclusion chromatography (SEC) analysis. The results were referred to other aqueous base solvents used for dispersing starch (NaOH and KOH). The samples were separated using SEC with triple detection and phosphate buffer (pH 8.0) with urea as the eluent. The characteristics of tested normal and waxy starches were compared. The results revealed that urea/NaOH did not degrade starch during the dispersion process. The recovery of starches, however, was not higher than 42%. These results prove that while the urea/NaOH solvent allows to obtain cold-water-soluble starch, the degree of disintegration of the intramolecular interactions of amylopectin chains is still insufficient.

Co-delivery of terbinafine hydrochloride and urea with an in situ film-forming system for nail targeting treatment

Onychomycosis is a chronic nail disorder consisting of a fungal infection that causes physical and psychosocial discomfort to patients. However, its treatment remains challenging owing to the barrier of the highly keratinized nail plate and the short time that conventional formulations reside on nails. In this work, we developed an in situ film-forming system(IFFS) based on Eudragit® RLPO to co-deliver terbinafine hydrochloride (TBH) and urea, i.e., TBH-urea-RLPO IFFS, with the aim of overcoming the nail barrier, prolonging the residence time, and efficiently treating onychomycosis. The IFFS formulation formed a thin film with good appearance and adhesion upon application in situ. The physical states of TBH and urea in the film were evaluated with polarization microscopy and powder X-ray diffraction. TBH and urea were both amorphousmiscible components within the RLPO film. TBH release from TBH-urea-RLPO IFFS fitted to the Korsmeyer-Pappas model, and the cumulative release at 72 h was significantly higher than that from commercial preparations (Lamisil Pedisan® once). In vitro permeation of TBH from TBH-urea-RLPO IFFS through bovine hoof membranes was evaluated in comparison with the film containing TBH alone (TBH-RLPO) and commercial preparations. The retention and cumulative permeated amount of TBH were significantly enhanced for the TBH-urea-RLPO IFFS (170.80 ± 44.63 μg/cm²vs 75.49 ± 21.50 μg/cm²vs 60.25 ± 27.38 μg/cm²; 61.81 ± 16.09 μg/cm²vs 21.80 ± 11.56 μg/cm²vs 7.91 ± 1.03 μg/cm², respectively), and the membranes treated with different formulations were observed with SEM and FTIR to identify the denaturing effect of urea on bovine hoof keratin. In vitro antifungal tests against Trichophyton rubrum,Microsporum canis, Fusarium, and Aspergillus fumigatus were cultured on Muller-Hinton agar; the findings indicated that TBH-urea-RLPO IFFS enhanced TBH antifungal activity. Overall, the results support that TBH-urea-RLPO IFFS is an efficient and promising approach for onychomycosis targeting treatment.

The effect of plasticizers on thermoplastic starch films developed from the indigenous Ethiopian tuber crop Anchote (Coccinia abyssinica) starch

Anchote (Coccinia abyssinica) starch films were prepared by a solution casting method with glycerol, 1-ethyl-3-methylimidazolium acetate, sorbitol or triethylene glycol as plasticizers. The effect of these plasticizers and their concentration on film microstructure, thermal, and mechanical properties was investigated. Scanning electron microscopy revealed that regardless of plasticizer type, films possessing higher plasticizer content had more homogeneous morphologies than those with lower plasticizer content. The FTIR spectra of films plasticized with 1-ethyl-3-methylimidazolium acetate had higher intensity peaks at 3150, 1400 and 1000 cm-1 when compared to other film peaks. These data show that 1-ethyl-3-methylimidazolium acetate plasticized films have decreased molecular order which results in less hydrogen bonding. For this reason, films developed from 1-ethyl-3-methylimidazolium acetate were more flexible than the others. The effect of plasticizers on the thermal properties of the anchote starch films was investigated using thermogravimetric analysis (TGA). Films made from 30% (w/w) plasticizer concentration exhibited higher thermal stability for all types of plasticizer. Mechanical testing showed that sorbitol films had the highest tensile strength, approximately 2 times that of the triethylene glycol plasticized film and 3 times that of the film made from 1-ethyl-3-methylimidazolium acetate.

Antiplasticization of Polymer Materials: Structural Aspects and Effects on Mechanical and Diffusion-Controlled Properties

Antiplasticization of glassy polymers, arising from the addition of small amounts of plasticizer, was examined to highlight the developments that have taken place over the last few decades, aiming to fill gaps of knowledge in the large number of disjointed publications. The analysis includes the role of polymer/plasticizer molecular interactions and the conditions leading to the cross-over from antiplasticization to plasticization. This was based on molecular dynamics considerations of thermal transitions and related relaxation spectra, alongside the deviation of free volumes from the additivity rule. Useful insights were gained from an analysis of data on molecular glasses, including the implications of the glass fragility concept. The effects of molecular packing resulting from antiplasticization are also discussed in the context of physical ageing. These include considerations on the effects on mechanical properties and diffusion-controlled behaviour. Some peculiar features of antiplasticization regarding changes in Tg were probed and the effects of water were examined, both as a single component and in combination with other plasticizers to illustrate the role of intermolecular forces. The analysis has also brought to light the shortcomings of existing theories for disregarding the dual cross-over from antiplasticization to plasticization with respect to modulus variation with temperature and for not addressing failure related properties, such as yielding, crazing and fracture toughness.

Application of ultrasonic irradiation as a benign method for production of glycerol plasticized-starch/ascorbic acid functionalized MWCNTs nanocomposites: Investigation of methylene blue adsorption and electrical properties

A solution mixing and ultrasonic dispersion method as a green, the fast, inexpensive and effective technique was utilized to prepare glycerol plasticized-starch (GPS)/ascorbic acid (AA)-MWCNTs nanocomposites (NCs) via the introduction of various amounts of AA-MWCNTs (3, 6 and 9wt%) as filler into GPS matrix. The GPS was synthesized by addition of glycerol (50%) as a plasticizer to starch which enhances its flexibility. Characterization of the obtained GPS/AA-MWCNTs NCs was accomplished by different techniques. The optimum filler content for the generation of fine electrical conductivity and good mechanical properties was found to be about 3wt%. The distribution of AA-MWCNTs at the low content (3wt%) in the GPS matrix was better due to the strong linkage between nanofiller and GPS in GPS/AA-MWCNTs NC. The results of adsorption studies showed that the fabricated NC can be a good adsorbent for removal of methylene blue (MB) dye from aqueous solutions.

Attributes of natural and synthetic materials pertaining to slow-release urea coating industry

Urea is one of the spirited input materials for plant growth. However, more than half of conventional urea applied to the soil may not reach the plants and be washed off by rain and irrigation water. The high lost proportion results not only in economic losses but also in environmental pollution. Alleviation in cost and nitrogen pollution is possible by mitigating the nitrogen release rate and synchronizing it with the plant’s need. A wide range of synthetic and natural materials are being tested for production of slow-release fertilizers. Each one of these materials has its own merits, with accompanying disadvantages. This study critically reviews the most featured natural and synthetic materials pertaining to the slow-release urea industry. The focused review was aimed at elaborating the benefits and limitations of polymeric and nonpolymeric coating materials, release mechanism of conventional and coated urea, methods to characterize the coated urea, slow-release characteristics imparted by a coating to the coated urea, and release patterns of conventional and coated urea. This discussion was further extended to commercially available coatings and slow-release potential of superabsorbent, urethane, and starch-based coatings.