Formation and characterization of pseudo-polyrotaxanes based on poly(p-dioxanone) and cyclodextrins

Fabrication and evaluation of 3D printed poly(l-lactide) copolymer scaffolds for bone tissue engineering

The application of poly(L-lactic acid) (PLLA) in tissue engineering is limited due to its brittleness and uncontrollable degradation rate. In this study, the flexible p-dioxanone (PDO) and highly reactive glycolide (GA) units were introduced into PLLA segments by chemical modification to prepare poly(l-lactide-ran-p-dioxanone-ran-glycolide) (PLPG) copolymers. The copolymers were then processed into the PLPG scaffold by a 3D printing technology. The physicochemical properties of the PLPG copolymers were studied by NMR, DSC, XRD, GPC, and SEM. Furthermore, the mechanical properties, degradation properties, and biocompatibility of the PLPG scaffolds were also studied. The results showed that introducing PDO and GA units disrupted the regularity of PLLA, decreasing the crystallinity of the PLPG copolymers. However, introducing PDO and GA units could effectively improve the mechanical and degradation properties of the PLLA scaffolds. In vitro cell culture experiments indicated that the PLPG scaffolds supported proliferation, growth, and differentiation of MC3T3-E1 cells. The PLPG scaffolds reported herein, with controllable degradation rates and mechanical performance, may find applications in bone tissue engineering.

A novel biocompatible polymeric blend for applications requiring high toughness and tailored degradation rate

Finding the right balance in mechanical properties and degradation rate of biodegradable materials for biomedical applications is challenging, not only at the time of implantation but also during biodegradation. For instance, high elongation at break and toughness with a mid-term degradation rate are required for tendon scaffold or suture application, which cannot be found in each alpha polyester individually. Here, we hypothesise that blending semi-crystalline poly(p-dioxanone) (PDO) and poly(lactide-co-caprolactone) (LCL) in a specific composition will enhance the toughness while also enabling tailored degradation times. Hence, blends of PDO and LCL (PDO/LCL) were prepared in varying concentrations and formed into films by solvent casting. We thoroughly characterised the chemical, thermal, morphological, and mechanical properties of the new blends before and during hydrolytic degradation. Cellular performance was determined by seeding mouse fibroblasts onto the samples and culturing for 72 hours, before using proliferation assays and confocal imaging. We found that an increase in LCL content causes a decrease in hydrolytic degradation rate, as indicated by induced crystallinity, surface and bulk erosions, and tensile properties. Interestingly, the noncytotoxic blend containing 30% PDO and 70% LCL (PDO3LCL7) resulted in small PDO droplets uniformly dispersed within the LCL matrix and demonstrated a tailored degradation rate and toughening behaviour with a notable strain-hardening effect reaching 320% elongation at break; over 3 times the elongation of neat LCL. In summary, this work highlights the potential of PDO3LCL7 as a biomaterial for biomedical applications like tendon tissue engineering or high-performance absorbable sutures.

Influence of several biodegradable components added to pure and nanosilver-doped PMMA bone cements on its biological and mechanical properties

Acrylic bone cements (BC) are wildly used in medicine. Despite favorable mechanical properties, processability and inject capability, BC lack bioactivity. To overcome this, we investigated the effects of selected biodegradable additives to create a partially-degradable BC and also we evaluated its combination with nanosilver (AgNp). We hypothesized that using above strategies it would be possible to obtain bioactive BC. The Cemex was used as the base material, modified at 2.5, 5 or 10 wt% with either cellulose, chitosan, magnesium, polydioxanone or tricalcium-phosphate. The resulted modified BC was examined for surface morphology, wettability, porosity, mechanical and nanomechanical properties and cytocompatibility. The composite BC doped with AgNp was also examined for its release and antibacterial properties. The results showed that it is possible to create modified cement and all studied modifiers increased its porosity. Applying the additives slightly decreased BC wettability and mechanical properties, but the positive effect of the additives was observed in nanomechanical research. The relatively poor cytocompatibility of modified BC was attributed to the unreacted monomer release, except for polydioxanone modification which increased cells viability. Furthermore, all additives facilitated AgNp release and increased BC antibacterial effectiveness. Our present studies suggest the optimal content of biodegradable component for BC is 5 wt%. At this content, an improvement in BC porosity is achieved without significant deterioration of BC physical and mechanical properties. Polydioxanone and cellulose seem to be the most promising additives that improve porosity and antibacterial properties of antibiotic or nanosilver-loaded BC. Partially-degradable BC may be a good strategy to improve their antibacterial effectiveness, but some caution is still required regarding their cytocompatibility. STATEMENT OF SIGNIFICANCE: The lack of bone cement bioactivity is the main limitation of its effectiveness in medicine. To overcome this, we have created composite cements with partially-degradable properties. We also modified these cements with nanosilver to provide antibacterial properties. We examined five various additives at three different contents to modify a selected bone cement. Our results broaden the knowledge about potential modifiers and properties of composite cements. We selected the optimal content and the most promising additives, and showed that the combination of these additives with nanosilver would increase cements` antibacterial effectiveness. Such modified cements may be a new solution for medical applications.

Photothermally triggered disassembly of a visible dual fluorescent poly(ethylene glycol)/α-cyclodextrin hydrogel

The real-time tracking and adjustment of the disassembly and status of hydrogels in vivo are important challenges to accurate and precise assessment. In this article, a photothermally controllable, visible, dual fluorescent thermosensitive hydrogel was designed and developed based on a porphyrin-poly(ethylene glycol)/IR-820-α-cyclodextrin hydrogel. Due to the photothermal effect and fluorescence emission of IR-820, it can exert the dual functions of photothermal control and fluorescence imaging tracking. The IR-820 conjugated hydrogel can regulate the hydrogel disassembly by the photothermal effect of IR-820. Furthermore, each component of the hydrogel can be tracked by the fluorescence of IR-820 and porphyrin. Fluorescence imaging tracking and remote photothermal control were merged into the visible and controlled hydrogel disassembly after subcutaneous injection using mice as models. The dual fluorescence imaging visualization of cyclodextrin/poly(ethylene glycol) hydrogels revealed the disassembly process by tracking each component, and the hydrogel disassembly can be efficiently accelerated under laser irradiation with the photothermal effect of IR-820. This affords an important basis for understanding the disassembly process of the poly(ethylene glycol)/α-cyclodextrin hydrogel.

Crystallization behavior of poly(p-dioxanone) with cyclodextrin complex and nucleation mechanism discussion

In the interest of improving the crystallization rate of poly(p-dioxanone) (PPDO), an inclusion complex (IC) based on β-cyclodextrin (β-CD) and polyglycolide (PGA) serving as a green nucleating agent for PPDO was achieved by a solution technique.