Removal of fluoride and natural organic matter from natural tropical brackish waters by nanofiltration/reverse osmosis with varying water chemistry

Aluminum-Crosslinked Nanocellulose Scaffolds for Fluoride Removal

Anionic carboxylated cellulose nanofibers (CNF) are effective media to remove cationic contaminants from water. In this study, sustainable cationic CNF-based adsorbents capable of removing anionic contaminants were demonstrated using a simple approach. Specifically, the zero-waste nitro-oxidization process was used to produce carboxylated CNF (NOCNF), which was subsequently converted into a cationic scaffold by crosslinking with aluminum ions. The system, termed Al-CNF, is found to be effective for the removal of fluoride ions from water. Using the Langmuir isotherm model, the fluoride adsorption study indicates that Al-CNF has a maximum adsorption capacity of 43.3 mg/g, which is significantly higher than that of alumina-based adsorbents such as activated alumina (16.3 mg/g). The selectivity of fluoride adsorption in the presence of other anionic species (nitrate or sulfate) by Al-CNF at different pH values was also evaluated. The results indicate that Al-CNF can maintain a relatively high selectivity towards the adsorption of fluoride. Finally, the sequential applicability of using spent Al-CNF after the fluoride adsorption to further remove cationic contaminant such as Basic Red 2 dye was demonstrated. The low cost and relatively high adsorption capacity of Al-CNF make it suitable for practical applications in fluoride removal from water.

A state-of-art-review on emerging contaminants: Environmental chemistry, health effect, and modern treatment methods

Pollution problems are increasingly becoming e a priority issue from both scientific and technological points of view. The dispersion and frequency of pollutants in the environment are on the rise, leading to the emergence have been increasing, including of a new class of contaminants that not only impact the environment but also pose risks to people's health. Therefore, developing new methods for identifying and quantifying these pollutants classified as emerging contaminants is imperative. These methods enable regulatory actions that effectively minimize their adverse effects to take steps to regulate and reduce their impact. On the other hand, these new contaminants represent a challenge for current technologies to be adapted to control and remove emerging contaminants and involve innovative, eco-friendly, and sustainable remediation technologies. There is a vast amount of information collected in this review on emerging pollutants, comparing the identification and quantification methods, the technologies applied for their control and remediation, and the policies and regulations necessary for their operation and application. In addition, This review will deal with different aspects of emerging contaminants, their origin, nature, detection, and treatment concerning water and wastewater.

The model and mechanism of adsorptive technologies for wastewater containing fluoride: A review

With the continuous development of society, industrialization, and human activities have been producing more and more pollutants. Fluoride discharge is one of the main causes of water pollution. This review summarizes various commonly used and effective fluoride removal technologies, including ion exchange technology, electrochemical technology, coagulation technology, membrane treatment, and adsorption technology, and points out the outstanding advantages of adsorption technology. Various commonly used fluoride removal techniques as well as typical adsorbent materials have been discussed in published papers, however, the relationship between different adsorbent materials and adsorption models has rarely been explored, therefore, this paper categorizes and summarizes the various models involved in static adsorption, dynamic adsorption, and electrosorption fluoride removal processes, such as pseudo-first-order and pseudo-second-order kinetic models, Langmuir and Freundlich isotherm models, Thomas and Clark dynamic adsorption models, including the mathematical equations of the corresponding models and the significance of the models are also comprehensively summarized. Furthermore, this comprehensive discussion delves into the fundamental adsorption mechanisms, quantification of maximum adsorption capacity, evaluation of resistance to anion interference, and assessment of adsorption regeneration performance exhibited by diverse adsorption materials. The selection of the best adsorption model not only predicts the adsorption performance of the adsorbent but also provides a better description and understanding of the details of each part of the adsorption process, which facilitates the adjustment of experimental conditions to optimize the adsorption process. This review may provide some guidance for the development of more cost-effective adsorbent materials and adsorption processes in the future.

Synthesis of Composites for the Removal of F- Anions

This work presents the synthesis of amine and ferrihydrite functionalized graphene oxide for the removal of fluoride from water. The synthesis of the graphene oxide and the modified with amine groups is developed by following the modified Hummer's method. Fourier transform infrared spectrometry, X-ray, Raman spectroscopy, thermogravimetric analysis, surface charge distribution, specific surface area and porosity, adsorption isotherms, and the van't Hoff equation are used for the characterization of the synthesized materials. Results show that the addition of amines with ferrihydrite generates wrinkles on the surface layers, suggesting a successful incorporation of nitrogen onto the graphene oxide; and as a consequence, the adsorption capacity per unit area of the materials is increased.

Water quality of The Gambia River: A prospective drinking water supply

Drinking water in The Gambia is mostly derived from boreholes that could potentially be contaminated. The Gambia River, a major river in West Africa that covers 12 % of the country's area, could be more exploited for drinking water supply. During the dry season, the total dissolved solids (TDS), ranging from 0.02 to 33 g/L in The Gambia River, decreases with the distance to the river mouth with no major inorganic contamination. The freshwater (<0.8 g/L TDS) starts from Jasobo at approximately 120 km from the river mouth and extends by about 350 km to the eastern border of The Gambia. With a dissolved organic carbon (DOC) ranging from 2 to 15 mgC/L, the natural organic matter (NOM) of The Gambia River was characterised by 40-60 % humic substances of paedogenic origin. With such characteristics, unknown disinfection by-products could be formed if chemical disinfection, such as chlorination, was implemented during treatment. Out of 103 types of micropollutants, 21 were detected (4 pesticides, 10 pharmaceuticals, 7 per- and polyfluoroalkyl substances (PFAS)) with concentrations ranging from 0.1 to 1500 ng/L. Pesticides, bisphenol A and PFAS concentrations were below the stricter EU guidelines set for drinking water. These were mainly confined to the urban area of high population density near the river mouth, while the quality of the freshwater region of low population density was surprisingly pristine. These results indicate that The Gambia River, especially in its upper regions, would be well suited as a drinking water supply when using decentralised ultrafiltration treatment for the removal of turbidity, as well as, depending on pore size, to a certain extent microorganisms and DOC.

Impact of Silver-Decorated Graphene Oxide (Ag-GO) towards Improving the Characteristics of Nanohybrid Polysulfone Membranes

The utilization of membranes has been extensively employed in the treatment of water and wastewater. Membrane fouling, attributed to the hydrophobic nature of membranes, constitutes a noteworthy concern in the realm of membrane separation. The mitigation of fouling can be achieved through the modification of membrane characteristics, including but not limited to hydrophilicity, morphology, and selectivity. In this study, a nanohybrid polysulfone (PSf) membrane embedded with silver-graphene oxide (Ag-GO) was fabricated to overcome problems related to biofouling. The embedment of Ag-GO nanoparticles (NPs) is the aim towards producing membranes with antimicrobial properties. The fabricated membranes at different compositions of NPs (0 wt%, 0.3 wt%, 0.5 wt%, and 0.8 wt%) are denoted as M0, M1, M2, and M3, respectively. These PSf/Ag-GO membranes were characterized using FTIR, water contact angle (WCA) goniometer, FESEM, and salt rejection. The additions of GO significantly improved the hydrophilicity of PSf membranes. An additional OH peak at 3380.84 cm^-1 of the nanohybrid membrane from FTIR spectra may be related to hydroxyl (-OH) groups of GO. The WCA of the fabricated membranes decreased from 69.92° to 54.71°, which confirmed the improvement in its hydrophilicity. In comparison to the pure PSf membrane, the morphology of the finger-like structure of the fabricated nanohybrid membrane slightly bent with a larger bottom part. Among the fabricated membranes, M2 achieved the highest iron (Fe) removal, up to 93%. This finding proved that the addition of 0.5 wt% Ag-GO NPs enhanced the membrane water permeability together with its performance of ionic solute removal (Fe²⁺) from synthetic groundwater. In conclusion, embedding a small amount of Ag-GO NPs successfully improved the hydrophilicity of PSf membranes and was able to achieve high removal of Fe at 10-100 mg L^-1 towards purification of groundwater for safe drinking water.

A comprehensive review on permeable reactive barrier for the remediation of groundwater contamination

Groundwater quality is deteriorating due to contamination from both natural and anthropogenic sources. Traditional "Pump and Treat" techniques of treating the groundwater suffer from the disadvantages of a small-scale and energy-intensive approach. Permeable reactive barriers (PRBs), owing to their passive operation, offer a more sustainable strategy for remediation. This promising technique focuses on eliminating heavy metal pollutants and hazardous aromatic compounds by physisorption, chemisorption, precipitation, denitrification, and/or biodegradation. Researchers have utilized ZVI, activated carbon, natural and manufactured zeolites, and other by-products as reactive media barriers. Environmental parameters, i.e., pH, initial pollutant concentration, organic substance, dissolved oxygen, and reactive media by-products, all influence a PRB's performance. Although their long-term impact and performance are uncertain, PRBs are still evolving as viable alternatives to pump-and-treat techniques. The use of PRBs to remove anionic contaminants (e.g., Fluoride, Nitrate, etc.) has received less attention since precipitates can clog the reactive barrier and hinder groundwater flow. In this paper, we present an insight into this approach and the tremendous implications for future scientific study that integrates this strategy using sustainability and explores the viability of PRBs for anionic pollutants.

Removal of natural organic matter from surface water sources by nanofiltration and surface engineering membranes for fouling mitigation - A review

Given that surface water is the primary supply of drinking water worldwide, the presence of natural organic matter (NOM) in surface water presents difficulties for water treatment facilities. During the disinfection phase of the drinking water treatment process, NOM aids in the creation of toxic disinfection by-products (DBPs). This problem can be effectively solved using the nanofiltration (NF) membrane method, however NOM can significantly foul NF membranes, degrading separation performance and membrane integrity, necessitating the development of fouling-resistant membranes. This review offers a thorough analysis of the removal of NOM by NF along with insights into the operation, mechanisms, fouling, and its controlling variables. In light of engineering materials with distinctive features, the potential of surface-engineered NF membranes is here critically assessed for the impact on the membrane surface, separation, and antifouling qualities. Case studies on surface-engineered NF membranes are critically evaluated, and properties-to-performance connections are established, as well as challenges, trends, and predictions for the field's future. The effect of alteration on surface properties, interactions with solutes and foulants, and applications in water treatment are all examined in detail. Engineered NF membranes containing zwitterionic polymers have the greatest potential to improve membrane permeance, selectivity, stability, and antifouling performance. To support commercial applications, however, difficulties related to material production, modification techniques, and long-term stability must be solved promptly. Fouling resistant NF membrane development would be critical not only for the water treatment industry, but also for a wide range of developing applications in gas and liquid separations.

State-of-the-art of research progress on adsorptive removal of fluoride-contaminated water using biochar-based materials: Practical feasibility through reusability and column transport studies

Fluoride (F^-) is one of the essential elements found in soil and water released from geogenic sources and several anthropogenic activities. Fluoride causes fluorosis, dental and skeletal growth problems, teeth mottling, and neurological damage due to prolonged consumption, affecting millions worldwide. Adsorption is an extensively implemented technique in water and wastewater treatment for fluoride, with significant potential due to efficiency, cost-effectiveness, ease of operation, and reusability. This review highlights the current state of knowledge for fluoride adsorption using biochar-based materials and the limitations of biochar for fluoride-contaminated groundwater and industrial wastewater treatment. Biochar materials have shown significant adsorption capacities for fluoride under the influence of low pH, biochar dose, initial concentration, temperature, and co-existing ions. Modified biochar possesses various functional groups (-OH, -CC, -C-O, -CONH, -C-OH, X-OH), in which enhanced hydroxyl (-OH) groups onto the surface plays a significant role in fluoride adsorption via electrostatic attraction and ion exchange. Regeneration and reusability of biochar sorbents need to be performed to a greater extent to improve removal efficiency and reusability in field conditions. Furthermore, the present investigation identifies the limitations of biochar materials in treating fluoride-contaminated drinking groundwater and industrial effluents. The fluoride removal using biochar-based materials at an industrial scale for understanding the practical feasibility is yet to be documented. This review work recommend the feasibility of biochar-based materials in column studies for fluoride remediation in the future.

Fluoride removal from aqueous solution via environmentally friendly adsorbent derived from seashell

Nowadays, the presence of excessive ions in water resources is of utmost concern and has attracted increasing attention; therefore, excessive amounts of these ions such as fluoride should be removed from drinking water. Conventional water treatment processes are shown to be incapable of the complete removal of redundant fluoride from aqueous water bodies, whereas adsorption is a promising, effective, cost–benefit, and simple method for this purpose. This study aimed to synthesize effective adsorbents from bivalve shells and evaluate the adsorption function of bivalve shells in removing fluoride from aqueous solutions. In this study, the oyster shell was collected from the Persian Gulf’s seaside and were crushed by manual mortar and blender, and graded with standard sieves with 70 mesh size. The prepared bivalve shell was characterized by SEM and FTIR. To investigate and optimize various variables on fluoride removal percentage a response surface methodology based on central composite design (RSM-CCD) was used. Under optimal conditions (pH: 5.5, adsorbent dose: 0.3 g/L, contact time: 85 min and fluoride concentration: 3 mg/L) the maximum removal efficiency was 97.26%. Results showed that the adsorption equilibrium and kinetic data were matched with the isotherm Langmuir Model (R² = 0.98) with q_max = 27.31 mg/g and pseudo-second-order reaction (R² = 0.99). Also, a thermodynamic study exhibited that the adsorption process of fluoride into bivalve shells was an exothermic reaction and could not be a spontaneous adsorption process. Based on the results, the bivalve shell was found as an appropriate adsorbent to remove fluoride from aqueous solutions.

Evaluation of a Smectite Adsorption-Based Electrostatic System to Decontaminate F− Rich Thermal Waters

Several studies have shown the presence of fluoride levels much higher than the 1.5 mg/L threshold concentration recommended by WHO in the spring waters and wells of the Ethiopian Rift Valley. Available defluoridation techniques can be costly, present complicated technical aspects, and show limited effectiveness. Therefore, it is necessary to devise innovative, sustainable, and effective solutions. This study proposes an alternative method of intervention to the known techniques for removing fluoride from water, particularly suitable for smaller rural communities. In particular, in this work, the possibility to use electromagnetic fields as a physical method for removing the excess fluoride was investigated. The study was carried out by developing a multiphysics model used for studying and envisaging the design of a device. In this framework, the combination of this approach with the use of highly reactive smectite clay was numerically studied. The results obtained, although preliminary, indicate that the proposed system could significantly impoverish the waters of the Rift Valley from fluoride, with the consequence of obtaining a resource suitable for human consumption, in particular for rural communities. However, further theoretical investigations and experimental phases will be necessary to achieve the desired results.

Modification of cyclodextrin and use in environmental applications

Water pollution, which has become a global problem in parallel with environmental pollution, is a problem that needs to be solved urgently, considering the gradual depletion of water resources. The inadequacy of the water treatment methods and the materials used somehow directed the researchers to look for dual character structures such as biocompatible and biodegradable β-cyclodextrin (β-CD). β-CD, which is normally insoluble in water, is used in demanding wastewater applications by being modified with the help of different agents to be water soluble or transformed into polymeric adsorbents as a result of co-polymerization via cross-linkers. In this way, in addition to the host-guest interactions offered by β-CD, secondary forces arising from these interactions provide advantages in terms of regeneration and reusability. However, the adsorption efficiency and synthesis steps need to be improved. Based on the current studies presented in this review, in which cross-linkers and modification methods are also mentioned, suggestions for novel synthesis methods of new-generation β-CD-based materials, criticisms, and recent methods of removal of micropollutants such as heavy metals, industrial dyes, harmful biomolecules, and pharmaceutics wastes are mentioned.

Removal of Organic Compounds with an Amino Group during the Nanofiltration Process

The research covered the process of nanofiltration of low molecular weight organic compounds in aqueous solution. The article presents the results of experiments on membrane filtration of compounds containing amino groups in the aromatic ring and comparing them with the results for compounds without amino groups. The research was carried out for several commercial polymer membranes: HL, TS40, TS80, DL from various manufacturers. It has been shown that the presence of the amino group and its position in relation to the carboxyl group in the molecule affects the retention in the nanofiltration process. The research also included the oxidation products of selected pharmaceuticals. It has been shown that 4-Amino-3,5-dichlorophenol—a oxidation product of diclofenac and 4-ethylbenzaldehyde—a oxidation product of IBU, show poor separation efficiency on the selected commercial membranes, regardless of the pH value and the presence of natural organic matter (NOM). It has been shown that pre-ozonation of natural river water can improve the retention of pollutants removed.

Batch fluidized bed reactor based modified biosynthetic crystals: Optimization of adsorptive properties and application in fluoride removal from groundwater

A batch fluidized bed reactor (BFBR) with modified biosynthetic crystals (MBC), derived from Pseudomonas sp. HXF1, was investigated for the treatment of the groundwater containing fluoride (F^-). Impacts of different hydraulic retention time (HRT), pH, and initial F^- concentration on F^- removal were examined and the maximum defluorination efficiency was recorded as 95.20%. Moreover, recycling experiments were performed to evaluate the stability of repeated use. BFBR/MBC system showed a long-term effective treatment outcome with low fluctuation in the concentrations of residual Ca²⁺ and F^-. The formed precipitates were characterized by SEM, XPS, XRD, and FTIR. The defluorination mechanisms of BFBR/MBC system were defined as the chemisorption and induced crystallization of Ca₅(PO₄)₃F on the MBC surface. As a feasible, economical, and environment-friendly technique, the method has a long-term value, which suggests promising applications in F^- removal and resourceful treatment.

Investigation of kinetics and adsorption isotherm for fluoride removal from aqueous solutions using mesoporous cerium-aluminum binary oxide nanomaterials

Herein, we report the synthesis of Ce–Al (1 : 1, 1 : 3, 1 : 6, and 1 : 9) binary oxide nanoparticles by a simple co-precipitation method at room temperature to be applied for defluoridation of an aqueous solution. The characterization of the synthesized nanomaterial was performed by XRD (X-ray diffraction), FTIR (Fourier transform infrared) spectroscopy, TGA/DTA (thermogravimetric analysis/differential thermal analysis), BET (Brunauer–Emmett–Teller) surface analysis, and SEM (scanning electron microscopy). Ce–Al binary oxides in 1 : 6 molar concentration were found to have the highest surface area of 110.32 m² g⁻¹ with an average crystallite size of 4.7 nm, which showed excellent defluoridation capacity. The adsorptive capacity of the prepared material towards fluoride removal was investigated under a range of experimental conditions such as dosage of adsorbents, pH, and initial fluoride concentration along with adsorption isotherms and adsorption kinetics. The results indicated that fluoride adsorption on cerium–aluminum binary metal oxide nanoparticles occurred within one hour, with maximum adsorption occurring at pH 2.4. The experimental data obtained were studied using Langmuir, Freundlich, and Temkin adsorption isotherm models. The nanomaterial showed an exceptionally high adsorbent capacity of 384.6 mg g⁻¹. Time-dependent kinetic studies were carried out to establish the mechanism of the adsorption process by pseudo-first-order kinetics, pseudo-second-order kinetics, and Weber–Morris intraparticle diffusion kinetic models. The results indicated that adsorption processes followed pseudo-second-order kinetics. This study suggests that cerium–aluminum binary oxide nanoparticles have good potential for fluoride removal from highly contaminated aqueous solutions.

Mesoporous Ce–Al binary oxide nanomaterials prepared with a surface area of 110.32 m² g⁻¹ showed defluoridation capacity at pH 2.4, exhibited maximum adsorption capacity of 384.6 mg g⁻¹ and a removal efficiency of 91.5% at a small dose of nanoadsorbent.

Fluoride Polluted Groundwaters in Calabria Region (Southern Italy): Natural Source and Remediation

Excessive ingestion of fluoride through the consumption of F−-rich drinking water could cause adverse effects to human health. For this reason, the WHO has fixed 1.5 mg/L as the maximum F- concentration for drinking water. In this work, a detailed geochemical characterization was performed to define the source of natural pollution of two groundwaters (samples Pc and Bg) coming from deep crystalline aquifers located in the Calabria region (southern Italy) and to define and optimize the most appropriate water treatment strategy. The samples were classified as a F− enriched NaHCO3 type of water. In particular, the F− concentrations observed were 30 mg/L and 8.9 mg/L for the Pc and Bg samples, respectively. Based on the acquired geochemical characterization knowledge, the groundwaters were treated by two thin-film composite NF membranes, namely SPR 10113 and SPR 10114 which have so far not been used for water defluoridation. It was found that the SPR 10114 membrane was able to guarantee water permeates with F− contents lower than the threshold value of 1.5 mg/L for both treated waters, whereas the fluoride content remained above the threshold value when the Pc sample was treated using the SPR 10113 membrane. The obtained permeates were characterized by a low ionic load and were not suitable for long-term consumption as drinking water. However, all of the produced waters did not need any further re-mineralizing processes for agricultural irrigation or other purposes.

Bivalve shells (Corbula trigona) as a new adsorbent for the defluoridation of groundwater by adsorption-precipitation

Defluoridation of groundwater was performed in a batch reactor using bivalve shell powder (BSP) as adsorbent. The physicochemical characteristics of BSP, studied by Fourier Transform Infrared, X-ray Diffraction and Inductively Coupled Plasma-Optical Emission Spectrometry after dissolution, have shown that BSP was mainly composed of crystalline CaCO₃ (∼97.8%). The effects of pH, initial fluoride concentration, adsorbent dose and contact time on the adsorption capacity of BSP were investigated. For an initial fluoride concentration of 2.2 mg/L and with 16 g/L of BSP, after 8 hours of treatment, 27.3% were eliminated at pH 7.5 versus 68% at pH 3, highlighting the efficiency of the adsorption process. The difference in adsorption capacity as a function of pH was correlated to the pHpzc of the BSP, which was equal to 8.2. Thus, at pH below pHpzc, electrostatic attraction between the fluoride anions and the positively charged adsorbent could justify the adsorption mechanism. Fittings of experimental data have evidenced that the adsorption kinetics were of pseudo-second order whereas the adsorption isotherms were of Langmuir type. The chemical precipitation of calcium fluoride was also revealed to occur upon release of Ca²⁺ from partial dissolution of CaCO₃ in acidic conditions.

Frontiers of Membrane Desalination Processes for Brackish Water Treatment: A Review

Climate change, population growth, and increased industrial activities are exacerbating freshwater scarcity and leading to increased interest in desalination of saline water. Brackish water is an attractive alternative to freshwater due to its low salinity and widespread availability in many water-scarce areas. However, partial or total desalination of brackish water is essential to reach the water quality requirements for a variety of applications. Selection of appropriate technology requires knowledge and understanding of the operational principles, capabilities, and limitations of the available desalination processes. Proper combination of feedwater technology improves the energy efficiency of desalination. In this article, we focus on pressure-driven and electro-driven membrane desalination processes. We review the principles, as well as challenges and recent improvements for reverse osmosis (RO), nanofiltration (NF), electrodialysis (ED), and membrane capacitive deionization (MCDI). RO is the dominant membrane process for large-scale desalination of brackish water with higher salinity, while ED and MCDI are energy-efficient for lower salinity ranges. Selective removal of multivalent components makes NF an excellent option for water softening. Brackish water desalination with membrane processes faces a series of challenges. Membrane fouling and scaling are the common issues associated with these processes, resulting in a reduction in their water recovery and energy efficiency. To overcome such adverse effects, many efforts have been dedicated toward development of pre-treatment steps, surface modification of membranes, use of anti-scalant, and modification of operational conditions. However, the effectiveness of these approaches depends on the fouling propensity of the feed water. In addition to the fouling and scaling, each process may face other challenges depending on their state of development and maturity. This review provides recent advances in the material, architecture, and operation of these processes that can assist in the selection and design of technologies for particular applications. The active research directions to improve the performance of these processes are also identified. The review shows that technologies that are tunable and particularly efficient for partial desalination such as ED and MCDI are increasingly competitive with traditional RO processes. Development of cost-effective ion exchange membranes with high chemical and mechanical stability can further improve the economy of desalination with electro-membrane processes and advance their future applications.

Photocatalytic-persulfate- oxidation for diclofenac removal from aqueous solutions: Modeling, optimization and biotoxicity test assessment

In this paper, the influence of several aquatic factors (the nature of catalyst, the initial pH and the initial concentration of the pollutant) on the photocatalytic degradation of diclofenac (DFC), one of the most widely prescribed anti-inflammatory non-steroidal drug, was studied. Also, in order to examine the intensification process, the variation of the photocatalytic DFC degradation in the presence of sodium persulfate (PPS) was analyzed. It was found that, compared to titanium dioxide (TiO₂), the zinc oxide (ZnO) photocatalyst performed exceptionally well, with a 96.13% DFC degradation efficiency after 150 min. The photodegradation of DFC by ZnO catalyst fitted well the Langmuir-Hinshelwood kinetic model. The maximum efficiency is 97.27% for simulated solar-UVA/ZnO/PPS and 77% for simulated solar-UVA/ZnO. In order to determine the optimal conditions leading to the maximization of DFC removal, an artificial neural network (ANN) modeling approach combined with genetic algorithm (GA) was applied. The best ANN determined had a correlation of 0.999 and it was further used in the process optimization where a 99.7% degradation efficiency was identified as the optimum under the following conditions: DFC initial concentration 37,9 mg L^-1, pH 5,88 and PPS initial concentration 500 mg L^-1. The effectiveness of the process and the toxicity of the pharmaceutical pollutants and their by-products were also evaluated and confirmed by the biological tests using liver and kidney of Mus musculus mice.

Submerged nanofiltration without pre-treatment for direct advanced drinking water treatment

Membrane fouling is a major challenge toward achieving direct nanofiltration (NF) treatment of surface water. This study aimed to evaluate the potential of the novel submerged flat-sheet NF membrane module to achieve low fouling propensity and high separation performance during the direct filtration of surface water. Laboratory-scale NF tests showed that the transmembrane pressure (TMP) increased only by 10 kPa over 24 d during the direct treatment of river and dam water. The NF system showed high (>80%) and stable rejection of color and organics, as well as low and variable conductivity rejection (28-47%). The rejection of negatively charged trace organic chemicals (TOrCs) was >50%, while that of uncharged or positively charged TOrCs was <50%. Another NF test that was conducted at a drinking water treatment plant showed negligible membrane fouling with a TMP increase of 3 kPa over 35 d. Separation performance of the NF system remained high: total organic carbon (TOC) removal was >70%, which was greater than the conventional rapid sand filtration system with powdered activated carbon and intermediate chlorine doses (TOC removal = 20-60%). Overall, this study demonstrated high water quality and stable system operation of the submerged flat-sheet NF system during direct treatment of surface water.

Removal of Naturally Occurring Strontium by Nanofiltration/Reverse Osmosis from Groundwater

Removal of naturally occurring strontium (Sr) from groundwater is vital as excessive exposure may lead to bone growth problems in children. Nanofiltration/reverse osmosis (NF/RO) is commonly used in groundwater treatment due to the high effectiveness and simple maintenance of these pressure driven membrane processes. In this research, a pilot-scale NF/RO system was used to desalinate a natural groundwater sample containing high Sr concentration (10.3 mg/L) and “old” groundwater organic matter (70.9 mg/L) from Esilalei in northern Tanzania to understand the removal of strontium by NF/RO. The impact of applied pressure (10–15 bar) and groundwater pH (3–12) on the membrane performance including permeate flux, strontium and total organic carbon (TOC) flux and removal was investigated. Increasing applied pressure was found to enhance the flux by increasing the driving force and enhance Sr and TOC removal by dilution effect (water flux higher than Sr passage). The alkaline pH caused severe flux decline likely due to membrane fouling and scaling, while it slightly enhanced Sr removal of RO membranes, but weakened the TOC removal. In contrast, acidic and neutral pH of groundwater enhanced TOC removal. These findings suggest that appropriately high applied pressure and acidic pH condition of groundwater are recommended to apply to the NF/RO membrane system in groundwater desalination to achieve better membrane performance.

Removal of fluoride from water using activated carbon fibres modified with zirconium by a drop-coating method

Metal-modified carbon materials have been widely used for fluoride removal, but the traditional impregnation by soaking method suffers from low loading of metals and substantial use of chemicals. This study proposed a new approach to prepare zirconium modified activated carbon fibres (Zr-ACF) by a drop-coating method. Using the same amount of chemicals, the drop-coating method yielded a 5.5 times higher fluoride adsorption capacity than the soaking method due to more effective loading of Zr(IV) onto ACF. The effects of various preparation conditions, including the addition of a complexing agent (oxalic acid) and Zr/ACF mass ratio (0.2-1), were investigated. Zr-ACF prepared by drop-coating was characterised by SEM and BET, and the functional groups involved in the anchoring of Zr(IV) on ACF and the adsorption of fluoride onto Zr-ACF were identified by FTIR and XPS. Adsorption experiments at pH between 3 and 11 revealed that ion exchange and electrostatic attraction were the main adsorption mechanisms at different pH levels. Co-existing anions such as CO₃^2-, HCO₃^- and Cl^- had an insignificant negative impact (<5%) on fluoride adsorption capacity while SO₄^2- decreased fluoride adsorption capacity by 11.5%. The adsorption kinetics followed the pseudo-second-order model. The adsorption isotherms followed the Langmuir isotherm model with a maximum fluoride adsorption capacity of 28.50 mg/L at 25 °C, which was higher than other carbon-based materials in the literature. The remarkable improvement of adsorption capacity and reduced chemical consumption demonstrate that Zr-ACF prepared by drop-coating is a promising adsorbent for fluoride removal.

Removal of fluoride in membrane-based water and wastewater treatment technologies: Performance review

The presence of excess fluoride in aqueous media above local environmental standards (e.g., the U.S. Environmental Protection Agency (EPA) standard of 4 mg/L) affects the health of aquatic life. Excess fluoride in drinking water above the maximum contaminant level (e.g., the World Health Organization (WHO) standard of 1.5 mg/L) also affects the skeletal and nervous systems of humans. Fluoride removal from aqueous solutions is difficult using conventional electrochemical, precipitation, and adsorption methods owing to its ionic size and reactivity. Thus, new technologies have been introduced to reduce the fluoride concentration in industrial wastewater effluents and various drinking water sources. Membrane technology is one of the newer technologies found to be very effective in significantly reducing fluoride to desired standards levels; however, it has received less attention than other technologies because it is perceived as a costly process. This study critically reviewed the performance of various membrane process and compared it with effluent and zero liquid discharge (ZLD) standards. The performance review has been conducted with the consideration of the theoretical background, rejection mechanisms, technical viability, and parameters affecting flux and rejection performance. This review includes membrane systems investigated for the defluoridation process but operated under pressure (i.e., reverse osmosis [RO] and nanofiltration [NF]), temperature gradients (i.e., membrane distillation [MD]), electrical potential gradients (i.e., electrodialysis [ED] and Donnan dialysis [DD]), and concentration differences (i.e., forward osmosis [FO]). Moreover, the study also addressed the advantages, limitations, & applicable conditions of each membrane based defluoridation process.

The adsorption characteristics of fluoride on commercial activated carbon treated with quaternary ammonium salts (Quats)

Commercial activated carbon was treated with six quaternary ammonium salts (Quats), namely, hexyltrimethylammonium (HTMA), octyltrimethylammonium (OTMA), decyltrimethylammonium (DCTMA), dodecyltrimethylammonium (DDTMA), Tetradecyltrimethylammonium (TDTMA), and hexadecyltrimethylammoium (HDTMA) as to enhance the fluoride adsorption capacity. In batch mode experiments, fluoride adsorption onto the Quats-treated activated carbon decreased dramatically with increase in solution pH. Fluoride removal by the Quats-treated activated carbons was closely related to the Quats chain length at less-than critical micelle concentration (CMC). Multi-site adsorption isotherm described fluoride adsorption characteristics well. Results showed that activated carbon treated with DDTMA exhibited the best fluoride adsorption density among all Quats investigated. DDTMA-treated activated carbons exhibited two-fold increase in the fluoride adsorption capacity compared to the untreated activated carbon. Results of regeneration, by alkaline desorption and/or Quats re-loading, showed fluoride-laden activated carbons have high reusability. DDTMA increased the positive surface charge of the activated carbon that enhanced fluoride adsorption. DDTMA-treated activated carbon was promising for fluoride removal from water with much enhanced removal capacity.

Source apportionment of environmentally persistent free radicals (EPFRs) in PM2.5 over Xi'an, China

Environmentally persistent free radicals (EPFRs) have recently attracted considerable attention as a new type of environmental risk substance due to their potential health effects. However, the sources and contributions of EPFRs in PM_2.5 are not yet clear. Therefore, this study reports the sources of EPFRs in PM_2.5 based on chemical analysis and positive matrix factorization (PMF). Daily PM_2.5 samples (116) were collected in Xi'an city from April 4 to December 29, 2017, and were quantitatively analyzed for EPFRs and other chemical constituents. The PMF model revealed contributions from five main sources of EPFRs in PM_2.5 (dust sources, coal combustion, secondary nitrates, industrial emissions and motor vehicle emissions). Coal combustion, motor vehicle emissions and dust sources are the top three contributors to EPFRs (76.12% in total). Coal combustion is highly important for PM_2.5 (35.10%) and EPFRs (16.75%). A high dust source contribution to EPFRs in spring may be due to dust storm events. Motor vehicle emissions are the top contributor to EPFRs, with a mean percentage of 32.13%. Secondary nitrates barely contributes to EPFRs (3.42%), indicating an EPFR origin from primary emissions rather than secondary inorganic reactions. Industrial emissions contribute less to PM_2.5 (4.31%) than to EPFRs (11.71%), which implies that fossil fuels contains many high-molecular-weight organics that could emit EPFRs. Integrating the PMF results with meteorological data revealed that atmospheric pollutants emitted in Xi'an city center could be transported to the sampling site by southern winds. These results suggest the need for further studies on the public health effects of EPFRs and can be used to help formulate source control measures to reduce the potential health risks posed by EPFRs in PM_2.5.

Fluoride contamination, health problems and remediation methods in Asian groundwater: A comprehensive review

In low concentration, fluoride is considered a necessary compound for human health. Exposure to high concentrations of fluoride is the reason for a serious disease called fluorosis. Fluorosis is categorized as Skeletal and Dental fluorosis. Several Asian countries, such as India, face contamination of water resources with fluoride. In this study, a comprehensive overview on fluoride contamination in Asian water resources has been presented. Since water contamination with fluoride in India is higher than other Asian countries, a separate section was dedicated to review published articles on fluoride contamination in this country. The status of health effects in Asian countries was another topic that was reviewed in this study. The effects of fluoride on human organs/systems such as urinary, renal, endocrine, gastrointestinal, cardiovascular, brain, and reproductive systems were another topic that was reviewed in this study. Different methods to remove fluoride from water such as reverse osmosis, electrocoagulation, nanofiltration, adsorption, ion-exchange and precipitation/coagulation were introduced in this study. Although several studies have been carried out on contamination of water resources with fluoride, the situation of water contamination with fluoride and newly developed technology to remove fluoride from water in Asian countries has not been reviewed. Therefore, this review is focused on these issues: 1) The status of fluoride contamination in Asian countries, 2) health effects of fluoride contamination in drinking water in Asia, and 3) the existing current technologies for defluoridation in Asia.