Experimental evidence of the kinetic performance achievable with columns packed with new 1.9μm fully porous particles of narrow particle size distribution

Evaluation of multi-solvent size exclusion chromatography columns packed with sub-2 μm particles for the characterization of synthetic polymers

With the recent development of small particle stationary-phases and dedicated instrumentation, the combination of size-exclusion chromatography (SEC) with ultra-high performance liquid chromatography (UHPLC) technology has been realized. It opened up a new polymer analysis technique called UHP-SEC. Although high resolution and fast analysis can be achieved, the multi-solvent suitability for a given column was limited to either organic or aqueous eluents. In this work, the capability of novel SEC columns (AdvanceBio SEC columns) packed with 1.9 μm particles for the characterization of synthetic polymers in organic solvents as well as the multi-solvent compatibility for organic and aqueous eluents have been demonstrated. About six times faster separation for both polystyrene (PS) and polyethylene glycol (PEG) with good peak shape and repeatability were achieved in comparison with standard SEC columns at comparable resolution. Especially for PEG, in contrast to other SEC columns, this column could provide close-to-accurate determination of molecular weights with tetrahydrofuran (THF) as mobile phase. Good reproducibility was obtained after switching several times from water to THF and vice versa with RSD% in retention times less than 0.5 %. Different samples such as polyols, isocyanates and additives can also be analyzed for molecular weight and distribution or composition determination. Volume overload, especially with injection volumes higher than 10 µL needs to be considered. This new column offers a powerful choice for oligomer and polymer analysis with both aqueous and organic mobile phase. Ultimately, hyphenating SEC columns to various detectors can enable more information regarding chemical composition, molecular weight, concentration, and structure.

Dimethyl carbonate as a green alternative to acetonitrile in reversed-phase liquid chromatography. Part I: Separation of small molecules

Nowadays, environmental problems are drawing the attention of governments and international organisations, which are therefore encouraging the transition to green industrial processes and approaches. In this context, chemists can help indicate a suitable direction. Beside the efforts focused on greening synthetic approaches, currently also analytical techniques and separations are under observation, especially those employing large volumes of organic solvents, such as reversed-phase liquid chromatography (RPLC). Acetonitrile has always been considered the best performing organic modifier for RPLC applications, due to its chemical features (complete miscibility in water, UV transparency, low viscosity etc); nevertheless, it suffers of severe shortcomings, and most importantly, it does not fully comply with Environmental, Health and Safety (EHS) requirements. For these reasons, alternative greener solvents are being investigated, especially easily available alcohols. In this work, chromatographic performance of the most common solvents used in reversed-phase chromatography, i.e., acetonitrile, ethanol and isopropanol, have been compared to a scarcely used solvent, dimethyl carbonate (DMC). The analytes of interest were two small molecules, caffeine and paracetamol, whose kinetics and retention behaviour obtained with the four solvents have been compared, and all contributions to band broadening have been assessed. Results about kinetic performance are very promising, indicating that a small amount (7 % v/v) of DMC is able to produce the same efficiency as a 2.5-times larger ACN volume (18 % v/v), and larger efficiency than alcohols. This paper reports, for the first time, fundamental studies concerning the mass transfer phenomena when DMC is used as an organic solvent in RPLC, and, together with the companion paper, represents the results of a research whose final aim was to discover whether DMC is suitable for chromatographic applications both in linear and preparative conditions.

Open tubular liquid chromatography: Recent advances and future trends

Nano-liquid chromatography (nanoLC) is gaining significant attention as a primary analytical technique across various scientific domains. Unlike conventional high-performance LC, nanoLC utilizes columns with inner diameters (i.ds.) usually ranging from 10 to 150 μm and operates at mobile phase flow rates between 10 and 1000 nl/min, offering improved chromatographic performance and detectability. Currently, most exploration of nanoLC has focused on particle-packed columns. Although open tubular LC (OTLC) can provide superior performance, optimized OTLC columns require very narrow i.ds. (< 10 μm) and demand challenging instrumentation. At the moment, these challenges have limited the success of OTLC. Nevertheless, remarkable progress has been made in developing and utilizing OTLC systems featuring narrow columns (< 2 μm). Additionally, significant efforts have been made to explore larger columns (10-75 μm i.d), demonstrating practical applicability in many situations. Due to their perceived advantages, interest in OTLC has resurged in the last two decades. This review provides an updated outlook on the latest developments in OTLC, focusing on instrumental challenges, achievements, and advancements in column technology. Moreover, it outlines selected applications that illustrate the potential of OTLC for performing targeted and untargeted studies.

Experimental diffusivity of energetic compounds determined by peak parking

Diffusivities of several explosive compounds, as well as other complex organic compounds were experimentally derived using a peak parking methodology. High performance liquid chromatography (HPLC) with stop flow 'parking' was used to experimentally determine diffusivity based on band broadening associated with chemical diffusion within the HPLC column. This research builds on prior methods by determining an obstruction factor through comparing benzene diffusion in methanol in a C18 column to the previously published capillary column. The method is useful for structures not easily described by computational chemistry methods or for solvents that do not have association coefficients in published diffusivity models. Using the peak parking method, diffusivities (cm²/s) ranged from 6.29 × 10^-7 to 1.06 × 10^-6 for hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 4.82 × 10^-5 to 1.26 × 10^-4 for 3-nitro-1,2,4-triazol-5-one (NTO), 1.63 × 10^-5 to 7.20 × 10^-6 for nitroguanidine (NQ), 7.07 × 10^-6 to 2.09 × 10^-5 for pyrimidine-2-carboxylic acid, and 1.02 × 10^-6 to 2.27 × 10^-6 for streptomycin. Compared to diffusivities estimated computationally, the empirical diffusivities reported herein estimated by two different methods have percent differences averaging 142%, 174%, 27%, 85%, and 33% for RDX, NTO, NQ, pyrimidine-2-carboxylic acid, and streptomycin, respectively. NTO had experimental diffusivities greater than the computational values, while RDX and streptomycin had experimental diffusivities lower than computational values.

Pattern-Type Separation of Triacylglycerols by Silver Thiolate×Non-Aqueous Reversed Phase Comprehensive Liquid Chromatography

Triacylglycerols (TAGs), as the main components of edible oils and animal fats, are responsible for the nutritional value, organoleptic features and technological properties of foods; each lipid matrix shows a unique TAG profile which can serve as fingerprint to ensure the quality and authenticity of food products. The high complexity of many foodstuffs often makes untargeted elucidation of TAG components a challenging task; thus, more efficient separation techniques may be mandatory. In this research, the TAG profile of a borage (Borago officinalis) seed oil was obtained by two-dimensional comprehensive liquid chromatography (LC×LC), by the coupling of silver thiolate and octadecylsilica monodisperse materials. A total 94 TAG compounds were identified by ion trap-time of flight detection, using atmospheric pressure ionization, with the degree of unsaturation varying from 0 to 9, and partition values ranging from 36 to 56. The group-type separation afforded by this analytical approach may be useful to quickly fingerprint TAG components of oil samples.

Performance of functionalized monolithic silica capillary columns with different mesopore sizes using radical polymerization of octadecyl methacrylate

We report on the possibility to enhance the phase ratio and retention factor in silica monoliths. According to pioneering work done by Núñez et al. [1], this enhancement is pursued by applying a stationary phase layer via radical polymerization with octadecyl methacrylate (ODM) as an alternative to the customary octadecylsilylation (C18-derivatization). The difference in band broadening, retention factor and separation selectivity between both approaches was compared. Different hydrothermal treatment temperatures for the column preparation were applied to produce monolithic silica structures with three different mesopore sizes (resp. 10, 13, and 16 nm, as determined by argon physisorption) while maintaining similar domain size (sum of through-pore and skeleton size). It has been found that the columns with the poly(octadecyl methacrylate)-phase (ODM columns) provided a 60 to 80% higher retention factor in methanol-water mixture compared to the octadecylsilylated (ODS) columns produced by starting from similar silica backbone structures. In acetonitrile-water mixture, the enhancement is smaller (15 to 30% times higher), yet significant. By adjusting the fabrication conditions (for both the preparation of the monolithic backbones and the surface functionalization), the achieved retention factors (up k = 4.89 for pentylbenzene in 80:20% (v/v) methanol/water) are obviously higher than obtained in the pioneering study on ODM monoliths of Núñez et al. [1], and column clogging could be completely avoided. In addition, also separation efficiencies were significantly higher than shown in Ref. [1], with plate heights as low as 5.8 μm. These plate heights are however inferior to those observed on the ODS-modified sister columns. The difference can be explained by the slower intra-skeleton diffusion displayed by the ODM-modified columns, in turn caused by the larger obstruction to diffusion originating from the thicker stationary phase layer.

Reduction of the extra-column band dispersion by a slow transport and splitting of a sample band in isocratic reversed-phase liquid chromatography

Sample introduction method was studied to reduce the extra-column effect in reversed-phase HPLC. Slow transport of a sample band (SToSB) in the pre-column space followed by the introduction of the band into the column at a near-optimum flow rate resulted in larger plate counts for a 1.0 mmID, 5 cm long column as much as 1.4-1.6 times for solutes with a retention factor (k) of 0.5-1.8 compared to a conventional elution method. Further reduction of the extra-column effect was possible by orthogonally splitting the sample band (SplSB) by flow switching during its slow transport followed by the introduction of the leading part of the band into the column. In this case, increased plate counts of up to 2-3 times for solutes with k of 0.5-1.8 were observed for a 1.0 mmID, 5 cm column. The sample introduction method, SToSB in the injector and the pre-column tube of a few μL, was found to reduce the extra-column band variance by 0.4-0.5 μL² for an UHPLC system with the extra-column volume (V_extra) of ca. 4.6 μL and the system variance (σ_extra²) of 1.1 μL² at flow rate of 100 μL/min, while SToSB and subsequent SplSB were found to be more effective, reducing σ_extra² by about 0.8 μL². With an UHPLC instrument with V_extra of about 10 μL and σ_extra² of ca. 3.6 μL² at flow rate of 300 μL/min, 1.4-2.1 times as many plate counts were observed with SToSB and SplSB compared to the normal elution method for early-eluting solutes with k=0.25-1.7 for a column, 2.1 mmID, 5 cm long. With this UHPLC instrument, SToSB and/or SplSB resulted in the reduction of σ_extra² by 1.2-2.2 μL².

Mass transfer kinetics on modern Whelk-O1 chiral stationary phases made on fully- and superficially-porous particles

In this work, a detailed study of mass transfer properties of trans-stilbene oxide (TSO) enantiomers on two Whelk-O1 chiral stationary phases (CSPs) has been performed. The CSPs were prepared by using both fully-porous silica particles of 2.5 μm particle diameter and superficially-porous ones of 2.6 μm particle diameter as base materials. By combining stop-flow and dynamic measurements in normal-phase conditions, the different contributions to mass transfer have been estimated. The study of intraparticle diffusion has revealed that the adsorption of both enantiomers is localized (i.e., characterized by absence of surface diffusion). The determination of thermodynamic binding constants (measured through adsorption isotherms) supports this finding.

Three approaches to improving performance of liquid chromatography using contour maps with pressure, time, and number of theoretical plates

Attempts to improve HPLC performance often focus on increasing the speed or separation performance. In this article, both the flow rate and column length are optimized as separation conditions, while observing the number of theoretical plates and hold-up time with isocratic elutions. In addition, the upper pressure limit must be simultaneously considered as the boundary condition. Approaches based on the optimal velocity (Opt.) are often adopted; but the kinetic performance limit (KPL) in Desmet's method can also be utilized for three-dimensional graphing with axes of pressure, time, and number of theoretical plates. Here, two approaches involving pressure increase are introduced, beginning with the condition of optimal linear velocity: one aimed at greater speed and the other at higher resolution. Coefficients of pressure-application are derived to measure the effectiveness of the intermediate conditions between the Opt. and KPL methods. In the third approach, the hold-up time is extended while maintaining a fixed pressure. Coefficients of time-extension are also derived, to determine the effectiveness to improve the separation performance.

Shedding light on mechanisms leading to convex-upward van Deemter curves on a cellulose tris(4-chloro-3-methylphenylcarbamate)-based chiral stationary phase

An unusual convex-upward van Deemter curve was observed for the more retained enantiomer of a chiral sulfoxide (2-(benzylsulfinyl)benzamide) on a cellulose tris(4-chloro-3-methylphenylcarbamate)-based chiral stationary phase (CSP), prepared on silica particles of 1000 Å pore size. In contrast, the firstly eluted enantiomer of the same molecule exhibited the traditional convex-downward van Deemter curve. A detailed kinetic and thermodynamic investigation has revealed that this unusual phenomenon, which however has already been observed in chiral chromatography, originates when the adsorption of the compound is very strong and the solid-phase diffusion negligible. Experimentally, the intraparticle diffusion of the more retained enantiomer of the sulfoxide was found to be one order of magnitude smaller than that of the first eluted one. Overall, this translates into very little longitudinal diffusion (b-term of van Deemter curve) accompanied by high solid-liquid mass transfer resistance (c-term). Finally the comparison with another, differently-substituted chiral sulfoxide (whose enantiomers both exhibit traditional van Deemter curve behavior) has allowed to correlate these findings to the specific characteristics of the molecule.

Detailed efficiency analysis of columns with a different packing quality and confirmation via total pore blocking

We report on a systematic study involving columns with a clearly different efficiency (4 distinct quality groups) obtained by packing the columns that were C₁₈ bonded and endcapped with a different carbon loading. Using B-term analysis (via peak parking) and theoretical models to estimate the magnitude of the C_m- and C_s-term contributions, it could be concluded that the difference in efficiency among the groups was entirely due to a difference in eddy dispersion. As such, the columns provided an ideal testing ground to verify how well the total pore blocking (TPB)-method can be used to probe differences in packing heterogeneity. In agreement with earlier literature observations, it turns out the TPB-method is much more sensitive to packing heterogeneities than the eddy dispersion (H_eddy)-contribution measured under open-pore conditions via B- and C- term subtraction. Typically, differences in H_eddy on the order of 0.1-0.5μm translate into a difference on the order of 0.5-2μm in the TPB mode. This confirms the TPB as a powerful technique to make very sensitive measurements of the homogeneity of packed beds.

The Way to Ultrafast, High-Throughput Enantioseparations of Bioactive Compounds in Liquid and Supercritical Fluid Chromatography

Until less than 10 years ago, chiral separations were carried out with columns packed with 5 or 3 μm fully porous particles (FPPs). Times to resolve enantiomeric mixtures were easily larger than 30 min, or so. Pushed especially by stringent requirements from medicinal and pharmaceutical industries, during the last years the field of chiral separations by liquid chromatography has undergone what can be defined a “true revolution”. With the purpose of developing ever faster and efficient method of separations, indeed, very efficient particle formats, such as superficially porous particles (SPPs) or sub-2 μm FPPs, have been functionalized with chiral selectors and employed in ultrafast applications. Thanks to the use of short column (1–2 cm long), packed with these extremely efficient chiral stationary phases (CSPs), operated at very high flow rates (5–8 mL/min), resolution of racemates could be accomplished in very short time, in many cases less than 1 s in normal-, reversed-phase and HILIC conditions. These CSPs have been found to be particularly promising also to carry out high-throughput separations under supercritical fluid chromatography (SFC) conditions. The most important results that have been recently achieved in terms of ultrafast, high-throughput enantioseparations both in liquid and supercritical fluid chromatography with particular attention to the very important field of bioactive chiral compounds will be reviewed in this manuscript. Attention will be focused not only on the latest introduced CSPs and their applications, but also on instrumental modifications which are required in some cases in order to fully exploit the intrinsic potential of new generation chiral columns.

Enantioselective ultra high performance liquid and supercritical fluid chromatography: The race to the shortest chromatogram

The ever-increasing need for enantiomerically pure chiral compounds has greatly expanded the number of enantioselective separation methods available for the precise and accurate measurements of the enantiomeric purity. The introduction of chiral stationary phases for liquid chromatography in the last decades has revolutionized the routine methods to determine enantiomeric purity of chiral drugs, agrochemicals, fragrances, and in general of organic and organometallic compounds. In recent years, additional efforts have been placed on faster, enantioselective analytical methods capable to fulfill the high throughput requirements of modern screening procedures. Efforts in this field, capitalizing on improved chromatographic particle technology and dedicated instrumentation, have led to highly efficient separations that are routinely completed on the seconds time scale. An overview of the recent achievements in the field of ultra-high-resolution chromatography on column packed with chiral stationary phases, both based on sub-2 μm fully porous and sub-3 μm superficially porous particles, will be given, with an emphasis on very recent studies on ultrafast chiral separations.

Future perspectives in high efficient and ultrafast chiral liquid chromatography through zwitterionic teicoplanin-based 2-μm superficially porous particles

With the aim of pushing forward the limits of high efficient and ultrafast chiral liquid chromatography, a new Chiral Stationary Phase (CSP) has been prepared by covalently bonding the teicoplanin selector on 2.0μm Superficially Porous Particles (SPPs). An already validated bonding protocol, which permits to achieve teicoplanin-based CSPs exhibiting zwitterionic behaviour, has been employed to prepare not only the 2.0μm version of the CSP but also two other analogous CSPs based, respectively, on 2.7μm SPPs and 1.9μm Fully Porous Particles (FPPs). The kinetic performance of these CSPs has been compared through the analysis of both van Deemter curves and kinetic plots by employing in-house packed columns of 4.6mm internal diameter and different lengths (20, 50 and 100mm). In particular on the columns packed with 2.0μm SPPs, extremely large efficiencies were observed for both achiral (>310,000 theoretical plates/meter, N/m; h_r: 1.61) and chiral compounds (>290,000 N/m; h_r: 1.72) in HILIC conditions. Thanks to their efficiency and enantioselectivity, these CSPs were successfully employed in ultrafast chiral separations. As an example, the enantiomers of haloxyfop were baseline resolved in about 3s, with a resolution higher than 2.0, (flow rate: 8mL/min) on a 2cm long column packed with the 2.0μm chiral SPPs.

Recent advances in capillary ultrahigh pressure liquid chromatography

In the twenty years since its initial demonstration, capillary ultrahigh pressure liquid chromatography (UHPLC) has proven to be one of most powerful separation techniques for the analysis of complex mixtures. This review focuses on the most recent advances made since 2010 towards increasing the performance of such separations. Improvements in capillary column preparation techniques that have led to columns with unprecedented performance are described. New stationary phases and phase supports that have been reported over the past decade are detailed, with a focus on their use in capillary formats. A discussion on the instrument developments that have been required to ensure that extra-column effects do not diminish the intrinsic efficiency of these columns during analysis is also included. Finally, the impact of these capillary UHPLC topics on the field of proteomics and ways in which capillary UHPLC may continue to be applied to the separation of complex samples are addressed.

Recent advancements and future directions of superficially porous chiral stationary phases for ultrafast high-performance enantioseparations

This review focuses on the use of superficially porous particles (SPPs) as chiral stationary phases for ultra-high performance liquid enantioseparations.