Low-cost and open-source strategies for chemical separations

Open-Source Absorbance Detector with Multiple Deep UV-LEDs for On-Capillary Multiwavelength Detection at a Single Point

On-capillary ultraviolet photometric detection (UV-PD) in a multiwavelength mode provides comprehensive analytical information. However, achieving single-point multiwavelength UV-PD for capillary-scale instruments typically requires high-cost and complex devices. This study presents the development of a cost-effective, open-source absorbance detector for on-capillary multiwavelength detection. The detector employs three deep UV light-emitting diodes emitting at 235, 255, and 278 nm as light sources, each coupled with its own photodetector for independent detection channels. The components are housed using 3D-printed parts, with an Arduino board used for data acquisition. Three individual optical paths, formed by three slits (60 μm width ×1 mm length), surround the measured capillary and converge at the same detection point. The detector demonstrates simultaneous multiwavelength detection of medicines for both HPLC and CE. This development represents an advancement in portable, low-cost analytical instrumentation, with broad implications for various fields of application.

Emerging Areas in Undergraduate Analytical Chemistry Education: Microfluidics, Microcontrollers, and Chemometrics

Analytical chemistry is a fast-paced field with frequent introduction of new techniques via research labs; however, incorporation of new techniques into academic curricula lags their adoption in research and industry. This review describes the recent educational literature on microfluidics, microcontrollers, and chemometrics in the undergraduate analytical chemistry curriculum. Each section highlights opportunities for nonexpert faculty to get started with these techniques and more advanced implementations suitable for experienced practitioners. While the addition of new topics to any curriculum brings some opportunity costs, student engagement with cutting edge techniques brings many benefits, including enhanced preparation for graduate school and professional careers and development of transferable skills, such as coding. Formal assessment of student outcomes is encouraged to promote broader adoption of these techniques.

Compact contactless conductometric, ultraviolet photometric and dual-detection cells for capillary electrophoresis via additive manufacturing

The growing demand for tailored detectors in capillary electrophoresis (CE), addressing tasks like field deployment or dual-detection analysis, emphasizes the necessity for compact detection cells. In this work, we propose cost-effective and user-friendly additive manufacturing (3D-printing) approaches to produce such miniaturized detection cells suitable for a range of CE applications. Firstly, capacitively-coupled contactless conductivity detection (C4D) cells of different sizes are fabricated by casting low-melting-point alloy into 3D-printed molds. Various designs of Faraday shields are integrated within the cells and compared. A mini-C4D cell (9.5×7.0×7.5 mm3) is produced, with limits of detection for alkaline cations ranging from 8-12 μM in a short-capillary based CE application. Secondly, ultraviolet photometric (UV-PD) detection cells are fabricated using 3D printing. These cells feature two narrow slits with a width of 60 μm, which are positioned along the path of incident and transmission light to facilitate collimation. A deep UV-LED (235 nm or 255 nm) is employed as the light source, and black resin is determined to be the optimal material for 3D printing the UV-PD cell, owing to its superior UV light absorption capabilities. The UV-PD cell is connected to the LED and photodetector through two optical fibers, making it easy to switch the light source and detector. The effective pathlength and stray light percentage for detecting on a 75 μm id capillary are 74 μm and 0.5 %, respectively. Thirdly, a dual-detection cell that combined C4D and UV-PD at a single detection point is proposed. The performance of direct detection by C4D and indirect detection by UV-PD is compared for detecting organic acids. The strategies for developing cost-effective compact detection cells facilitate the versatile integration of multiple detection methods in CE analysis.

An open source 3D printed autosampler for capillary electrophoresis

BACKGROUND

In-house built capillary electrophoresis (CE) systems represent a significant share of laboratory instrumentation. In most of these instruments, sample injection is effected manually with low to moderate precision and requires skilled operators. Although few automated samplers have been previously developed, typically only one sample at a time can be injected. If a series of samples is to be analyzed, manual intervention is required. In the present work, we developed and constructed a fully automated, open source, CE autosampler, able to handle up to 14 different samples that can be used as a modular component of any in-house built CE instrument.

RESULTS

An inexpensive, 3D printed, open source, autosampler for CE was developed. The autosampler consists of two parts: an injection unit with carousel containing sample and electrolyte vials and a flushing unit, containing a miniature pressure/vacuum pump. The autosampler is operated by an Arduino Mega microcontroller and an Arduino code written in the laboratory. The injection sequence is entered through a keypad and LCD display by the user. The instrument can operate autonomously for extended periods of time. It was used for fully automated analysis and/or calibration of up to 14 samples with excellent injection repeatability reaching less than 2.7% RSD for peak areas. The sampler performance was tested with two independently built CE instruments, a CE system with contactless conductivity detection (C4D) and a CE system with laser induced fluorescence (LIF) detector.

SIGNIFICANCE AND NOVELTY

A novel, 3D printed, Arduino-based autosampler for CE was developed. The autosampler allows autonomous hydrodynamic injection of up to 14 different samples with fully programmable injection sequence, including capillary flushing and high voltage and data acquisition control. It provides the missing instrumental sampling setup for laboratory made CE instruments. It can be simply constructed based on the open-source blueprints in any laboratory and be a useful and time-saving add-on to any modular CE instrument.

An open-source smart fraction collector for isocratic preparative liquid chromatography

Preparative liquid chromatography is a technique for separating complex samples or isolating pure compounds from complex extracts. It involves eluting samples through a packed column and selectively collecting or isolating the separated bands in a sequence of fractions. Depending on the column length and the sample complexity, a large number of fractions may be obtained, making fraction collection a laborious and time-consuming process. Manual fraction collection is also tedious, error-prone, less reproducible, and susceptible to contamination. Several commercial and lab-made solutions are available for automated fraction collection, but most systems do not synchronize with the instrument detector and collect fractions at fixed volumes or time intervals. We have assembled a low-cost Arduino-based smart fraction collector that can record the signal from the UV-vis detector of the chromatography instrument and enable the automated selective collection of the targeted bands. The system consists of a robot equipped with position sensors and a 3-way solenoid valve that switches the column effluent between the waste or collection positions. By proper programming, an Arduino board records the detector response and actuates the solenoid valve, the position sensors, and the stepper motors to collect the target chromatographic bands.

Closed-loop Control Systems for Pumps used in Portable Analytical Systems

The demand for accurate control of the flowrate/pressure in chemical analytical systems has given rise to the adoption of mechatronic approaches in analytical instruments. A mechatronic device is a synergistic system which combines mechanical, electronic, computer and control components. In the development of portable analytical devices, considering the instrument as a mechatronic system can be useful to mitigate compromises made to decrease space, weight, or power consumption. Fluid handling is important for reliability, however, commonly utilized platforms such as syringe and peristaltic pumps are typically characterized by flow/pressure fluctuations and slow responses. Closed loop control systems have been used effectively to decrease the difference between desired and realized fluidic output. This review discusses the way control systems have been implemented for enhanced fluidic control, categorized by pump type. Advanced control strategies used to enhance the transient and the steady state responses are discussed, along with examples of their implementation in portable analytical systems. The review is concluded with the outlook that the challenge in adequately expressing the complexity and dynamics of the fluidic network as a mathematical model has yielded a trend towards the adoption of experimentally informed models and machine learning approaches.

Three-in-One Detector by 3D Printing: Simultaneous Contactless Conductivity, Ultraviolet Absorbance, and Laser-Induced Fluorescence Measurements for Capillary Electrophoresis

We describe a 3-in-1 detector for simultaneous contactless conductivity (C⁴D), ultraviolet absorbance (UV-AD), and laser-induced fluorescence (LIF) measurements on a single detection point for capillary electrophoresis (CE). A key component of the detector was a rectangular detector head that was assembled with four 3D-printed parts. Two parts covering the detector head to function as a Faraday cage were fused deposition modeling printed using an electrically conductive material. The other two parts in between the conductive parts were stereolithography (SLA) printed with high-resolution (50 μm) constructions on the surface. After assembling the two SLA printed parts, several cavities were built with the surface constructions. Two electrodes and a Faraday shield for C⁴D were cast by injecting molten Wood's metal into the cavities. For UV-AD, a slit (100 μm width) was created by putting together two grooves (50 μm depth) on the surface of the SLA printed parts. A 255 nm UV-LED was used as the light source. The effective path length and stray light for a 50 μm id capillary were 39 μm and 13%, which were superior to those of other reported 3D-printed AD detectors. Confocal LIF detection was conducted by using an objective lens to focus the laser on the capillary via a through-hole. The detector was used to detect model analytes, including inorganic and organic ions, and fluorescein isothiocyanate labeled amino acids in a signal-run CE separation. In detecting fluorescein, LODs were 1.3 μM (C⁴D), 2.0 μM (UV-AD), and 1 nM (LIF). The calibration ranges covered from 0.01 μM to 500 μM.

Miniaturized open-source 2LabsToGo screening of lactose-free dairy products and saccharide-containing foods

The open-source 2LabsToGo system is the only one in its nature. It combines in one miniaturized instrument all relevant steps normally performed in a chemical and biological laboratory. For the first time, the applicability of the 2LabsToGo system was studied for screening 17 food products. As examples, saccharides were analyzed in eight products of different matrix complexity, and the absence of lactose was studied in nine lactose-free dairy products. Derivatization including homogeneous reagent application and plate heating via the 2LabsToGo system was explored for saccharide detection, and its performance was investigated. The visual detection sensitivity of lactose was comparable to previous studies. The precision of lactose in milk matrix (%RSD 4.6%) as well as the coefficient of determination of the calibration function (0.9995) were highly satisfying. The obtained lactose content of milk (4.5%) was plausible. Screening eight saccharide-containing food samples showed the saccharides in agreement with the expectations for the respective food product. The lactose content of nine different lactose-free dairy products was proven to be below the 0.1% lactose limit value. As proof-of-principle and for verification, these screening results obtained with the miniaturized 2LabsToGo system were reproduced using conventional state-of-the-art instrumentation, which led to the same results. However, instrumental costs were comparably low for the 2LabsToGo system. The application of the new 2LabsToGo system was successfully shown for saccharide screening, which is attractive to the field of quality control or official food control.

2LabsToGo─Recipe for Building Your Own Chromatography Equipment Including Biological Assay and Effect Detection

A complete recipe for building your own chromatography equipment from readily available materials is introduced. It combines sample separation (chemistry laboratory) with biological effect detection (biology laboratory). This hyphenation of two disciplines is necessary for prioritizing important compounds in complex samples. Among the thousands of compounds therein, it is often not clear which compounds are the important ones. On the same separation surface, additional detection of biological effects enables and guides substance prioritization. The newly developed open-source 2LabsToGo system for chemical and biological analysis is completely solvent-resistant and, due to miniaturization, environmentally friendly regarding the consumption of materials. It produces comparable results but is 10 times more compact (26 cm × 31 cm × 34 cm), 10 times lighter (6.8 kg), and 55 times less expensive (€ 1717) than current sophisticated commercial devices. As a proof of concept of the first 2LabsToGo system, the quality of different water samples was analyzed since clean water is becoming increasingly rare. In water, most of the thousands of substance signals or features can neither be identified nor classified toxicologically. However, methods that exploit this hyphenated strategy provide answers to such essential safety issues. Drinking or tap water did not show bioactive or toxic compounds, which was expected, whereas biogas or landfill water samples did. The hyphenated 2LabsToGo strategy is affordable and extremely useful for all laboratories with limited equipment but pressing challenges. It is ready to be used in various analytical tasks and applications.

Development of an Automatable Affinity Purification Process for DNA-Encoded Chemistry

DNA-encoded library technologies require high-throughput, compatible, and well automatable platforms for chemistry development, building block rehearsal, and library synthesis. An affinity-based process using Watson-Crick interactions was developed that enables purification of DNA-tagged compounds from complex reaction mixtures. The purification relies on a single-stranded DNA-oligonucleotide, called capture strand, which was covalently coupled to an agarose matrix and to which a DNA-compound conjugate from a DNA-encoded library (DEL) reaction can be reversibly annealed to. The thus-formed DNA duplex tolerated surprisingly stringent washing conditions with multiple solvents to remove excess reactants and reagents. The tolerated solvents included aqueous buffers, aqueous EDTA solutions to remove metal ions, aqueous mixtures of organic solvents, and even pure organic solvents. The purified DNA-conjugate was eluted with aqueous ammonia and could be used for reaction analysis or for instance in DNA-encoded library synthesis. The lab equipment for purification was tailored for automation with open-source hardware and constructed by 3D printing.

Low-Cost 3D-Printed Reactionware for the Determination of Fatty Acid Content in Edible Oils using a Base-Catalyzed Transesterification Method in Continuous Flow

A low-cost flow system was designed, manufactured, and tested to perform automated base-catalyzed transesterification of triacylglycerols to determine the fatty acid content in edible oils. In combination with traditional gas chromatographic analysis (GC-FID), this approach provides a semi-automated process that requires minimal manual intervention. The main flow system components, namely syringe pumps, connectors (i.e., flangeless fittings), and reactors, were manufactured using 3D-printing technology, specifically fused deposition modeling (FDM). By fine-tuning 3D-printer settings, high-quality leak-tight fittings with standard threading were manufactured in polypropylene (PP), which reduced the overall cost of the flow system significantly. Due to the enhanced reactivity in flow, lower catalyst concentrations (≤ 1.5 wt.%) were needed compared to traditional batch reactions (5 wt.%). The suitability of the automated flow method was determined by comparing results with the certified fatty acid content in sunflower seed oil from Helianthus annuus. Acceptable levels of accuracy (relative errors < 5%) and precision (RSD values ≤ 0.02%) were achieved. The mostly 3D-printed flow system was successfully used to determine the fatty acid content of sunflower and other commercial edible oils, namely avocado oil, canola oil, extra virgin olive oil, and a canola and olive oil blend. Linoleic acid (C18:2) was the major component in sunflower oil, whereas all other oils consisted mainly of oleic acid (C18:1). The fatty acid content of the edible oils was comparable to certified and literature values.

Capillary Electrophoresis as a Monitoring Tool for Flow Composition Determination

Flow analysis is the science of performing quantitative analytical chemistry in flowing streams. Because of its efficiency and speed of analysis, capillary electrophoresis (CE) is a prospective method for the monitoring of a flow composition withdrawn from various processes (e.g., occurring in bioreactors, fermentations, enzymatic assays, and microdialysis samples). However, interfacing CE to a various flow of interest requires further study. In this paper, several ingenious approaches on interfacing flow from various chemical or bioprocesses to a capillary electrophoresis instrument are reviewed. Most of these interfaces can be described as computer-controlled autosamplers. Even though most of the described interfaces waste too many samples, many interesting and important applications of the devices are reported. However, the lack of commercially available devices prevents the wide application of CE for flow analysis. On the contrary, this fact opens up a potential avenue for future research in the field of flow sampling by CE.

[Multimaterial 3D-printed contactless conductivity/laser-induced fluorescence dual-detection cell for capillary electrophoresis]

Dual detection, which simultaneously employs two complementary detection methods, is a useful approach to enhance the selectivity and sensitivity of capillary electrophoresis (CE). Through dual detection, multiple classes of analytes with different structural and chemical characteristics can be sensitively detected using a single CE method. In addition, the comigrating peaks can be distinguished by comparing the signal outputs of two detectors with different selectivities. Typically, dual detection is achieved by coupling two detectors in series along a capillary. However, in this approach, it is inconvenient to evaluate the signal outputs of the two detectors. The two detectors present differences in their corresponding effective capillary lengths and dead volumes of the detection cell. Therefore, detectors that combine two or three detection methods in a single detection point are proposed to address this issue. In this work, to fabricate a combined detector in a simple and low-cost manner, multimaterial 3D printing technology is employed. A two-in-one detection cell that combines capacitively coupled contactless conductivity detection (C4D) and confocal laser-induced fluorescence (LIF) detection was fabricated by 3D printing functional materials. In 3D printing, conductive composite polylactic acid (PLA, Proto-pasta) filaments and normal nonconductive PLA filaments were employed. The conductive material was used to build a C4D shielding layer that was electrically grounded. The nonconductive PLA was used as an electrical insulator placed between the shielding layer and C4D electrodes, which were two stainless-steel tubes (0.4 mm i.d. and 5 mm length). To embed the electrodes into the nonconductive material, a "print-pause-print" approach was applied. After building two chambers for housing electrodes using nonconductive PLA, the 3D printing was paused, following which the two electrodes were manually installed. Printing was then resumed, and the remaining part was built. The two electrodes were 2 mm apart, and the gap between them was filled with a conductive material for shielding to eliminate stray capacitance. A through-hole (1 mm i.d.) was placed between the middle conductive shielding layer for LIF detection. The size of the detection cell was 60 mm×29 mm×7.2 mm. The cell was screwed onto an XYZ stage to precisely align the light path of LIF detection, which was realized using a TriSep TM-2100LIF detector equipped with a 473 nm laser. C4D detection was achieved using a TraceDec detector equipped with a ChipCE adaptor. The two-in-one detector was coupled with a lab-made CE system that had a flow-through injection interface. Use of the detection cell allows the simultaneous detection of inorganic cations and fluorescein isothiocyanate (FITC)-labeled amino acids. The C4D excitation frequency and buffer concentration were then optimized. A mixture of 10 mmol/L 3-(N-morpholino)propanesulfonic acid (MOPS) and 10 mmol/L bis(2-hydroxyethyl)amino-tris(hydroxymethyl)methane (Bis-Tris) was selected as the background electrolyte as a compromise of C4D signal-to-noise ratio (S/N) and separation efficiencies of amino acids. The C4D excitation frequency was set to 77 kHz with S/N=233±8 for 200 μmol/L Na +. The baseline separation of Na+, K+, Li+, FITC, fluorescein, histidine (His), lysine (Lys), tryptophan (Trp), phenylalanine (Phe), alanine (Ala), and glycine (Gly) was achieved with a 25 μm i.d.×365 μm o.d.×45 cm (35 cm effective length) capillary and -10 kV separation voltage. The limits of detection (LODs) of C 4D for Na+, K+, and Li+were 2.2, 2.0, and 2.6 μmol/L, respectively. The LODs of LIF for fluorescein and FITC were 7.6 and 1.7 nmol/L, respectively. The relative standard deviations (RSDs) of the two detection methods were within the range of 0.3%-4.5% (n=3). The r 2 of the calibration curves was ≥0.9904. Thus, 3D printing technology is a simple and low-cost approach to implement complex designs, including those that are difficult to fabricate by traditional "workshop" technologies.

Catalytic Oxygenation-Mediated Extraction as a Facile and Green Way to Analyze Volatile Solutes

Sparging-based methods have long been used to liberate volatile organic compounds (VOCs) from liquid sample matrices prior to analysis. In these methods, a carrier gas is delivered from an external source. Here, we demonstrate "catalytic oxygenation-mediated extraction" (COME), which relies on biocatalytic production of oxygen occurring directly in the sample matrix. The newly formed oxygen (micro)bubbles extract the dissolved VOCs. The gaseous extract is immediately transferred to a separation or detection system for analysis. To start COME, dilute hydrogen peroxide is injected into the sample supplemented with catalase enzyme. The entire procedure is performed automatically-after pressing a "start" button, making a clapping sound, or triggering from a smartphone. The pump, valves, and detection system are controlled by a microcontroller board. For quality control and safety purposes, the reaction chamber is monitored by a camera linked to a single-board computer, which follows the enzymatic reaction progress by analyzing images of foam in real time. The data are instantly uploaded to the internet cloud for retrieval. The COME apparatus has been coupled on-line with the gas chromatography electron ionization mass spectrometry (MS) system, atmospheric pressure chemical ionization (APCI) MS system, and APCI ion-mobility spectrometry system. The three hyphenated variants have been tested in analyses of complex matrices (e.g., fruit-based drinks, whiskey, urine, and stored wastewater). In addition to the use of catalase, COME variants using crude potato pulp or manganese(IV) dioxide have been demonstrated. The technique is inexpensive, fast, reliable, and green: it uses low-toxicity chemicals and emits oxygen.

Robotized Noncontact Open-Space Mapping of Volatile Organic Compounds Emanating from Solid Specimens

Analysis of volatile organic compounds (VOCs) is normally preceded by sample homogenization and solvent extraction. This methodology does not provide spatial resolution of the analyzed VOCs in the examined matrix. Here, we present a robotized pen-shaped probe for open-space sampling and mapping of VOCs emanating from solid specimens (dubbed "PENVOC"). The system combines vacuum-assisted suction probe, mass spectrometry, and robotic handling of the probe. The VOCs are scavenged from the sample surface by a gentle hydrodynamic flow of air sustained by a vacuum pump. The sampled gas is transferred to the proximity of corona discharge in an atmospheric pressure chemical ionization source of a tandem mass spectrometer. The PENVOC has been attached to a robotic arm to enable unattended scanning of flat surfaces. The specimens can be placed away from the mass spectrometer during the scan. The robotized PENVOC has been characterized using chemical standards (benzaldehyde, limonene, 2-nonanone, and ethyl octanoate). The limits of detection are in the range from 2.33 × 10^-5 to 2.68 × 10^-4 mol m^-2. The platform has further been used for mapping of VOCs emanating from a variety of specimens: flowers, glove exposed to smoke, fuel stains, worn medical face mask, worn clothing, cheese, ham, and fruits. The chemical maps show unique distributions of the VOCs on the scanned surfaces. Obtaining comparable results (VOC maps) using other techniques (e.g., repetitive headspace sampling prior to offline analysis) would be time-consuming. The presented mapping technique may find applications in environmental, forensic, and food science.