Rapid growth of TiO2 nanotubes under the compact oxide layer: Evidence against the digging manner of dissolution reaction

Optimization of Photoelectrochemical Response on TiO2 Nanotube Arrays Treated by H3PO4 and Mechanism Analysis of the Slowing Down Effect during Preparation

The process control of anodization has been a hot topic for a long time. In this study, the addition of phosphoric acid to the traditional electrolyte changed the ion distribution on the reaction interface and the composition of the anion contamination layer so as to achieve the slowing down effect on anodization, the mechanism and theoretical model of which are also given in this paper. TiO2 is a common material in photoelectrocatalysis, but there are few studies on the photoelectrochemical performance of TiO2 nanotube arrays. The stability and rapidity of the photoelectrochemical response of TiO2 nanotube arrays prepared in phosphoric acid containing an electrolyte were effectively optimized in this study.

A comparative study of two-step anodization with one-step anodization at constant voltage

Two-step anodization has been widely used because it can produce highly self-organized anodic TiO₂nanotubes, but the differences in morphology and current-time curve of one-step anodization and two-step anodization are rarely reported. Here, one-step anodization and two-step anodization were conducted at different voltages. By comparing the FESEM image of anodic TiO₂nanotubes fabricated by one-step anodization and two-step anodization, it was found that the variation of morphology characteristics is same with voltage. The distinction of morphology and current-time curve between one-step anodization and two-step anodization at the same voltage were analyzed: the nanotube average growth rate and porosity of two-step anodization are greater than that of one-step anodization. In the current-time curve, the duration of stage I and stage II in two-step anodization are significantly shorter than one-step anodization. The traditional field-assisted dissolution theory cannot explain the three stages of the current-time curves and their physics meaning under different voltages in the same fluoride electrolyte. Here, the distinction between one-step anodization and two-step anodization was clarified successfully by the theories of ionic current and electronic current and oxygen bubble mould.

Understanding the influence of electrolyte aging in electrochemical anodization of titanium

Titania nanotubes or nanopores self-ordered on electrochemically anodized (EA) titanium have been widely applied towards photocatalysis, solar cells, purification and biomedical implants. As a result, significant research has been focused towards optimizing anodization to fabricate controlled, stable and reproducible nanostructures. Among these, the use of organic-based electrolyte, like ethylene glycol (with NH₄F and water), to anodize Ti has been widely applied and researched. Interestingly, among the various influencing EA factors, electrolyte aging (repeated EA using non-target Ti, prior to EA of target Ti substrate) has been underexplored, with only few studies aiming to optimize electrolyte aging and its influence on the nanostructures fabricated. Moreover, many research laboratories utilize electrolyte aging in Ti anodization, but this practice is seldom reported. In this extensive and pioneering review, we discuss and detail electrolyte aging in Ti anodization to fabricate controlled nanostructures, and its influence on nanostructure characteristics including morphology, chemistry, stability and application-specific performance. This review will inform future research aimed at optimizing electrolyte aging and Ti anodization to fabricate controlled nanostructures catering to specific application needs.

A review: research progress on the formation mechanism of porous anodic oxides

Owing to the great development potential of porous anodic oxides (PAO) in many fields, research on their formation mechanisms, fabrication processes and applications has a history of more than ten years. Although compared with research on the fabrication processes and applications of PAO, research on their formation mechanisms started late, several mainstream theories have been formed in the academic community, including the field-assisted dissolution (FAD) theory, the field-assisted ejection (FAE) theory, the self-organization theory, the ionic and electronic current theory and the oxygen bubble mould effect. This review will focus on summarizing the core views of the mainstream mechanisms mentioned above and comparing the explanations for some of their classical experimental phenomena.

Unraveling the six stages of the current-time curve and the bilayer nanotubes obtained by one-step anodization of Zr

The application and growth mechanism of anodic TiO2 nanotubes have been a hot topic in the last ten years, but the formation mechanism of anodic ZrO2 nanotubes has rarely been studied. In one-step constant voltage anodization of Al and Ti, the typical current-time curve has three stages. Moreover, the current-time curves of the three stages can last for 10 min or even 10 hours, resulting in a single layer of nanotubes with the same diameter due to the constant voltage in one-step anodization. However, in this paper, it was found for the first time that the three stages of the current-time curve appeared twice in succession during one-step constant voltage anodization of Zr for only 900 seconds, and bilayer nanotubes with increased diameter were obtained. This six-stage current-time curve cannot be explained by classical field-assisted dissolution and field-assisted flow or stress-driven mechanisms. Here, the formation mechanism and growth kinetics of bilayer ZrO2 nanotubes have been clarified rationally by the theories of ionic current, electronic current and oxygen bubble mold. The interesting results presented in this paper are of great significance for revealing the anodizing process of various metals and the formation mechanism of porous structures.

Plasmonic Spherical Nanoparticles Coupled with Titania Nanotube Arrays Prepared by Anodization as Substrates for Surface-Enhanced Raman Spectroscopy Applications: A Review

As surface-enhanced Raman spectroscopy (SERS) continues developing to be a powerful analytical tool for several probes, four important aspects to make it more accessible have to be addressed: low-cost, reproducibility, high sensibility, and recyclability. Titanium dioxide nanotubes (TiO₂ NTs) prepared by anodization have attracted interest in this field because they can be used as safe solid supports to deposit metal nanoparticles to build SERS substrate nanoplatforms that meet these four desired aspects. TiO₂ NTs can be easily prepared and, by varying different synthesis parameters, their dimensions and specific features of their morphology can be tuned allowing them to support metal nanoparticles of different sizes that can achieve a regular dispersion on their surface promoting high enhancement factors (EF) and reproducibility. Besides, the TiO₂ photocatalytic properties enable the substrate's self-cleaning property for recyclability. In this review, we discuss the different methodological strategies that have been tested to achieve a high performance of the SERS substrates based on TiO₂ NTs as solid support for the three main noble metal nanoparticles mainly studied for this purpose: Ag, Au, and Pt.

Evidence of oxygen bubbles forming nanotube embryos in porous anodic oxides

Anodic TiO2 nanotubes have been studied widely for two decades because of their regular tubular structures and extensive applications. However, the formation mechanism of anodic TiO2 nanotubes remains unclear, because it is difficult to find convincing evidence for popular field-assisted dissolution or field-assisted injection theories and the oxygen bubble model. Here, in a bid to find direct evidence that oxygen bubbles form nanotube embryos, a new method is applied to handle this challenge. Before nanotube formation, a dense cover layer was formed to make nanotubes grow more slowly. Many completely enclosed nanotube embryos formed by oxygen bubbles were found beneath the dense cover layer for the first time. The formation of these enclosed and hollow gourd-shaped embryos is convincing enough to prove that the nanotubes are formed by the oxygen bubble mold, similar to inflating a football, rather than by field-assisted dissolution. Based on the 'oxygen bubble model' and ionic current and electronic current theories, the formation and growth process of nanotube embryos is explained clearly for the first time. These interesting findings indicate that the 'oxygen bubble model' and ionic current and electronic current theories also apply to anodization of other metals.

Morphology and photoluminescence of nano-porous anodic alumina membranes obtained in oxalic acid at different anodization potentials

Porous Anodic alumina (PAA) with highly ordered pore geometry serves as an ideal template for future development of nanodevices. In the present work, PAA was prepared by varying anodization potential from 10 to 50 V in oxalic acid at 8 °C with a constant electrolyte concentration of 0.3 M. The influence of anodization potential on the structural and photoluminescence (PL) properties of PAA has been studied. The effect of anodization potential on the main pore characteristics of PAA such as pore diameter, interpore distance, pore density, porosity and circularity was studied. It was observed that circularity of PAA was nearly equal to one in the case of anodization potential of 40 V. Highest regularity ratio (RR) obtained for PAA formed in 40 V and it was calculated by WSxM software. It was noticed that with increasing anodization potential there is a slight change in PL spectra of PAA and shows a strong PL peak in blue region.