First stages of silver electrodeposition in a deep eutectic solvent. Comparative behavior in aqueous medium

Composition effects of electrodeposited Cu-Ag nanostructured electrocatalysts for CO2 reduction

The electrochemical carbon dioxide reduction (CO2RR) on Cu-based catalysts is a promising strategy to store renewable electricity and produce valuable C2+ chemicals. We investigate the CO2RR on Cu-Ag nanostructures that have been electrodeposited in a green choline chloride and urea deep eutectic solvent (DES). We determine the electrochemically active surface area (ECSA) using lead underpotential deposition (UPD) to investigate the CO2RR intrinsic activity and selectivity. We show that the addition of Ag on electrodeposited Cu primarily suppresses the production of hydrogen and methane. While the production of carbon monoxide slightly increases, the partial current of the total C2+ products does not considerably increase. Despite that the production rate of C2+ is similar on Cu and Cu-Ag, the addition of Ag enhances the formation of alcohols and oxygenates over ethylene. We highlight the potential of metal electrodeposition from DES as a sustainable strategy to develop bimetallic Cu-based nanocatalysts for CO2RR.

Hygroscopicity of 1:2 Choline Chloride:Ethylene Glycol Deep Eutectic Solvent: A Hindrance to its Electroplating Industry Adoption

Deep eutectic solvents have been established as feasible metal electroplating solvent alternatives over traditional toxic aqueous plating baths. However, water, either added intentionally or unintentionally, can significantly influence the solvent’s physical properties and performance, thereby hindering its industry application. In this study, the hygroscopicity, or the ability to absorb moisture from the environment, of synthesized ethaline (1:2 choline chloride:ethylene glycol) was investigated. The kinematic viscosity, electrical conductivity, electrochemical window, and water content of ethaline were monitored over a 2-week period. Karl Fischer titration tests showed that ethaline exposed to the atmosphere displayed significant hygroscopicity compared to its unexposed counterpart. 1H NMR spectroscopy revealed that water vapor was readily absorbed at the surface due to the hydrophilic groups present in the ethaline molecule. Water uptake resulted in the decrease in viscosity, increase in electrical conductivity and narrowing of the electrochemical window of ethaline. Solution heating at 100°C removed the absorbed moisture and allowed the recovery of the solvent’s initial properties.

Molecular approach about the effect of water on the electrochemical behaviour of Ag+ ions in urea-choline chloride-water mixture

The water influence on electrochemical behaviour of Ag⁺ ions in urea and choline chloride mixture was investigated by cyclic voltammetry technique, while the molecular insights about the investigated systems were obtained from molecular dynamic (MD) simulation. The water content was variated from 0 up to 10% (v/v). Cyclic voltammetry technique showed that the peak potential for Ag⁺/Ag redox couples shifted in direction to more positive potentials with the gradual increase of water content in solution, indicating that the addition of water electrocatalyses the kinetics of the reduction of Ag⁺ ions. The MD simulations demonstrated that water molecules do not interact strongly with Ag⁺ ions but induce a small reduction in the number of urea molecules around of the ion and that the water molecules adjust to free spaces in the mixture.

Tailored electrocatalysts by controlled electrochemical deposition and surface nanostructuring

Controlled electrodeposition and surface nanostructuring are very promising approaches to tailor the structure of the electrocatalyst surface, with the aim to enhance their efficiency for sustainable energy conversion reactions. In this highlight, we first summarise different strategies to modify the structure of the electrode surface at the atomic and sub-monolayer level for applications in electrocatalysis. We discuss aspects such as structure sensitivity and electronic and geometric effects in electrocatalysis. Nanostructured surfaces are finally introduced as more scalable electrocatalysts, where morphology, cluster size, shape and distribution play an essential role and can be finely tuned. Controlled electrochemical deposition and selective engineering of the surface structure are key to design more active, selective and stable electrocatalysts towards a decarbonised energy scheme.

Morphology Modulation of Ionic Surfactant Micelles in Ternary Deep Eutectic Solvents

Deep eutectic solvents (DES) are potentially greener solvents obtained through the complexation of simple precursors which, among other applications, have been investigated in recent years for their ability to support the self-assembly of amphiphilic molecules. It is crucial to understand the factors which influence surfactant solubility and self-assembly with respect to the interaction of the surfactant molecule with the DES components. In this work, small-angle neutron scattering (SANS) has been used to investigate the micellization of cationic (C_nTAB) and anionic (SDS) surfactants in a ternary DES comprising choline chloride, urea, and glycerol, where the hydrogen bond donors are mixed in varying molar ratios. The results show that in each case either globular or rodlike micelles are formed with the degree of elongation being directly dependent on the composition of the DES. It is hypothesized that this composition dependence arises largely from the poor solubility of the counterions in the DES, especially at low glycerol content, leading to a tighter binding of the counterion to the micelle surface and giving rise to micelles with a high aspect ratio. This potential for accurate control over micelle morphology presents unique opportunities for rheology control or to develop templated syntheses of porous materials in DES, utilizing the solvent composition to tailor micelle shape and size, and hence the pore structure of the resulting material.

Single Atom Nucleation of Cobalt over Graphene Oxide: Theory and Experimental Study

Nucleation and growth mechanism of Co electrodeposition over graphene oxide (GO) was studied using cyclic voltammetry (CV) and chronoamperometry techniques. The studies were performed over an aqueous electrolyte containing 10 mM CoSO₄·7H₂O maintained at an initial pH of 2.5. CV studies established that the deposition mechanism was diffusion-controlled and irreversible. Chronoamperometry studies revealed the presence of three concurrent processes: an initial adsorption current, which indicated adatom layer formation, 3D nucleation and growth of Co islands over GO, and hydrogen evolution over the deposited Co nanoclusters. It was observed that the nucleation rate increased with increasing the overpotential (η) for deposition (from 2.71 × 10⁴ cm^-2 s^-1 at η = 0.35 V to 3.62 × 10⁶ cm^-2 s^-1 at η = 0.90 V). Application of the classical theory of nucleation over the chronoamperometry results suggested that the free energy of formation of the critical nucleus was lower than room temperature thermal energy. This indicated that the nucleation and growth process was not activation-controlled but rather a kinetically controlled process. Application of Milchev's atomistic theory revealed that every single atom of Co deposited over the GO sheet was a supercritical nucleus that could grow into a cluster irreversibly.

Catalyst-Electrolyte Interactions in Aqueous Reline Solutions for Highly Selective Electrochemical CO2 Reduction

Achieving high product selectivities is one challenge that limits viability of electrochemical CO₂ reduction (CO₂ R) to chemical feedstocks. Here, it was demonstrated how interactions between Ag foil cathodes and reline (choline chloride + urea) led to highly selective CO₂ R to CO with a faradaic efficiency of (96±8) % in 50 wt % aqueous reline at -0.884 V vs. the reversible hydrogen electrode (RHE), which is a 1.5-fold improvement over CO₂ R in KHCO₃ . In reline the Ag foil was roughened by (i) dissolution of oxide layers followed by (ii) electrodeposition of Ag nanoparticles back on cathode. This surface restructuring exposed low-coordinated Ag atoms, and subsequent adsorption of choline ions and urea at the catalyst surface limited proton availability in the double layer and stabilized key intermediates such as *COOH. These approaches could potentially be extended to other electrocatalytic metals and lower-viscosity deep eutectic solvents to achieve higher-current-density CO₂ R in continuous-flow cell electrolyzers.

Electrodeposition of Sn and Sn Composites with Carbon Materials Using Choline Chloride-Based Ionic Liquids

Nano carbons, such as graphene and carbon nanotubes, show very interesting electrochemical properties and are becoming a focus of interest in many areas, including electrodeposition of carbon–metal composites for battery application. The aim of this study was to incorporate carbon materials (namely oxidized multi-walled carbon nanotubes (ox-MWCNT), pristine multi-walled carbon nanotubes (P-MWCNT), and reduced graphene oxide (rGO)) into a metallic tin matrix. Formation of the carbon–tin composite materials was achieved by electrodeposition from a choline chloride-based ionic solvent. The different structures and treatments of the carbon materials will create metallic composites with different characteristics. The electrochemical characterization of Sn and Sn composites was performed using chronoamperometry, potentiometry, electrochemical impedance, and cyclic voltammetry. The initial growth stages of Sn and Sn composites were characterized by a glassy-carbon (GC) electrode surface. Nucleation studies were carried out, and the effect of the carbon materials was characterized using the Scharifker and Hills (SH) and Scharifker and Mostany (SM) models. Through a non-linear fitting method, it was shown that the nucleation of Sn and Sn composites on a GC surface occurred through a 3D instantaneous process with growth controlled by diffusion. According to Raman and XRD analysis, carbon materials were successfully incorporated at the Sn matrix. AFM and SEM images showed that the carbon incorporation influences the coverage of the surface as well as the size and shape of the agglomerate. From the analysis of the corrosion tests, it is possible to say that Sn-composite films exhibit a comparable or slightly better corrosion performance as compared to pure Sn films.

On the cobalt and cobalt oxide electrodeposition from a glyceline deep eutectic solvent

The electrodeposition of cobalt and cobalt oxides from a glyceline deep eutectic solvent is reported.

Electrodeposition in Ionic Liquids

Due to their attractive physico-chemical properties, ionic liquids (ILs) are increasingly used as deposition electrolytes. This review summarizes recent advances in electrodeposition in ILs and focuses on its similarities and differences with that in aqueous solutions. The electrodeposition in ILs is divided into direct and template-assisted deposition. We detail the direct deposition of metals, alloys and semiconductors in five types of ILs, including halometallate ILs, air- and water-stable ILs, deep eutectic solvents (DESs), ILs with metal-containing cations, and protic ILs. Template-assisted deposition of nanostructures and macroporous structures in ILs is also presented. The effects of modulating factors such as deposition conditions (current density, current density mode, deposition time, temperature) and electrolyte components (cation, anion, metal salts, additives, water content) on the morphology, compositions, microstructures and properties of the prepared materials are highlighted.

Facile preparation of a highly sensitive nonenzymatic glucose sensor based on multi-walled carbon nanotubes decorated with electrodeposited metals

Preparation of Ni/CuAg/MWCNT hybrid composite modified electrode: (a) bare, (b) MWCNT, (c) CuAg/MWCNT, and (d) Ni/CuAg/MWCNT modified electrodes.