Sulfate radicals-based advanced oxidation processes for the degradation of pharmaceuticals and personal care products: A review on relevant activation mechanisms, performance, and perspectives

Hydroxylamine promoted degradation of organic contaminants using peroxydisulfate activated by Fe-alginate

To overcome the shortcomings of Fe(Ⅱ)/peroxydisulfate (PDS) system including the limited working pH range and large iron sludge production, a Fe-doped alginate (Fe-Alg) catalyst was prepared and combined with hydroxylamine (HA) to continuously activate PDS for the removal of organic pollutants in neutral condition. Due to the strong reductive capability of HA, it could significantly enhance the catalytic capability of Fe-Alg for PDS. The results of characterization suggested that Fe(Ⅲ)/Fe(Ⅱ) was evenly distributed in Alg through its complexation with carboxyl groups, and the reduction of Fe(Ⅲ) to Fe(Ⅱ) initiated by HA enabled Orange G (OG) to be continuously degraded in the Fe-Alg/HA/PDS system. The results of quenching experiments suggested that S O 4 ∙ - and HO• played a dominant role for OG removal in the Fe-Alg/HA/PDS process. The effect of influence factors (e.g. initial pH, HA concentration, Fe-Alg dose and PDS concentration) and water matrix components (i.e. S O 4 2 - , N O 3 - , Cl-, HC O 3 - and dissolved organic matters (DOM)) on the performance of Fe-Alg/HA/PDS system was systematically investigated. Other refractory organic contaminants, including diclofenac (DCF), sulfamethoxazole (SMX), oxytetracycline (OTC) and bisphenol AF (BPAF) were also efficiently eliminated in Fe-Alg/HA/PDS system, suggesting the feasibility of this system for the treatment of organic pollutants. This work provides a method to optimize Fe(Ⅱ)/PDS system and a novel process applied to degrade refractory pollutants.

LED-light-driven over ZnO/biochar nanocomposite for activation of peroxymonosulfate to enhanced photocatalytic removal of methyl orange dye in aqueous solutions

ABSTRACTOrganic dyes are stable and persistent toxic compounds in the aquatic environment that are refractory to decompose by removal methods such as physico-chemical, optical and biological. Their presence in the aquatic media threatens human and wildlife. Herein, ZnO nanoparticles (NPs) due to good chemical durability, low cost and good photocatalytic performance was anchored on biochar (ZnO@biochar) nanocomposites were synthesized towards activation of peroxymonosulfate (PMS) for the photocatalytic removal of methyl orange (MO) dye. Several methods were used to characterization of the nanocomposites including FESEM, XRD, PL, EDS, FT-IR spectroscopy, and N2 adsorption/desorption. The results of the techniques demonstrated that the well-dispersed ZnO NPs were loaded onto the biochar surface. According to the particle size distribution graph, the average particle size of 64 nm was obtained for the ZnO NPs. BET analyzes showed that pore volume, the specific surface area (SSA) and average pore size of the synthesized nanocomposite increased. The survey of effective operational parameters indicated that the highest photocatalytic activity for MO removal was in the pH 3 of solution, 5 ppm initial dye concentration, 30 mg ZnO/biochar nanocomposite, and 20 mg PMS dose under LED-50W lamp irradiation (97.03% in the reaction time of 80 min). During the process, the reduction of the total organic carbon (TOC) contents and chemical oxygen demand (COD) were observed. Moreover, the MO degradation kinetics under optimal operating conditions were determined. It is concluded that the ZnO@biochar nanocomposite/PMS process was an efficient degradation method for the decomposition of the dye pollutant.

Activation of persulfate with magnetic Fe3O4-municipal solid waste incineration bottom ash-derived zeolite core-shell materials for tetracycline hydrochloride degradation

A novel and environmentally friendly magnetic iron zeolite (MIZ) core-shell were successfully fabricated using municipal solid waste incineration bottom ash-derived zeolite (MWZ) coated with Fe3O4 and innovatively investigated as a heterogeneous persulfate (PS) catalyst. The morphology and structure composition of as-prepared catalysts were characterised, and it was proved that the core-shell structure of MIZ was successfully synthesised by coating Fe3O4 uniformly on the MWZ surface. The tetracycline hydrochloride (TCH) degradation experiment indicate that the optimum equimolar amount of iron precursors was 3 mmol (MIZ-3). Compared with other systems, MIZ-3 possessed a superior catalytic performance, and the degradation efficiency of TCH (50 mg·L-1) in the MIZ-3/PS system reached 87.3%. The effects of reaction parameters on the catalytic activity of MIZ-3, including pH, initial concentration of TCH, temperature, the dosage of catalyst, and Na2S2O8, were assessed. The catalyst had high stability according to three recycling experiments and the leaching test of iron ions. Furthermore, the working mechanism of the MIZ-3/PS system to TCH was discussed. The electron spin resonance (ESR) results demonstrated that the reactive radicals generated in the MIZ-3/PS system were sulphate radical (S O 4 - ∙ ) and hydroxyl radical (•OH). This work provided a novel strategy for TCH degradation under PS with a broad perspective on the fabrication of non-toxic and low-cost catalysts in practical wastewater treatment.

Enhanced degradation of reactive black 5 via persulfate activation by natural bornite: influencing parameters, mechanism and degradation pathway

Reactive black 5 (RBk5) is a refractory azo dye that constitutes a serious threat to the environment and humans. Herein, natural bornite (Nbo) was utilized to activate persulfate (PDS) for the RBk5 removal. The particle size of the Nbo catalyst was optimized and the RBk5 degradation rate constant that responded positively to the particle size of the Nbo catalyst was exhibited. Then, the operational factors affecting RBk5 removal were comprehensively investigated. With the addition of 1.5 g L-1 Nbo and 1.5 mM PDS, 99.05% of the RBk5 (20 mg L-1) was removed in 150 min compared with 0.46% removal with PDS only, which was caused by the additional reactive oxygen species (ROS) produced by the synergistic action of Fe-Cu bimetallic metal and reductive sulfur species. The Nbo catalyst presented high stability and reusability toward RBk5 removal. Identification of reactive oxygen species revealed that SO 4 ⋅ - , ·OH, O 2 ⋅ - and 1O2 collectively participated in RBk5 removal. Additionally, a possible degradation pathway for RBk5 was proposed, including cleavage of the azo, C-S and S-O bonds, hydroxylation, hydrolyzation, direct oxidation and other pathways. This work developed a highly effective and low-cost natural mineral-based bimetallic sulfide material for PDS activation for the degradation of contaminants and environmental remediation.

A review on recent advancements in the treatment of polyaromatic hydrocarbons (PAHs) using sulfate radicals based advanced oxidation process

Polyaromatic hydrocarbons (PAHs) are the most persistent compounds that get contaminated in the soil and water. Nearly 16 PAHs was considered to be a very toxic according US protection Agency. Though its concentration level is low in the environments but the effects due to it, is enormous. Advanced Oxidation Process (AOP) is an emergent methodology towards treating such pollutants with low and high molecular weight of complex substances. In this study, sulfate radical (SO4‾•) based AOP is emphasized for purging PAH from different sources. This review essentially concentrated on the mechanism of SO4‾• for the remediation of pollutants from different sources and the effects caused due to these pollutants in the environment was reduced by this mechanism is revealed in this review. It also talks about the SO4‾• precursors like Peroxymonosulfate (PMS) and Persulfate (PS) and their active participation in treating the different sources of toxic pollutants. Though PS and PMS is used for removing different contaminants, the degradation of PAH due to SO4‾• was presented particularly. The hydroxyl radical (•OH) mechanism-based methods are also emphasized in this review along with their limitations. In addition to that, different activation methods of PS and PMS were discussed which highlighted the performance of transition metals in activation. Also this review opened up about the degradation efficiency of contaminants, which was mostly higher than 90% where transition metals were used for activation. Especially, on usage of nanoparticles even 100% of degradation could be able to achieve was clearly showed in this literature study. This study mainly proposed the treatment of PAH present in the soil and water using SO4‾• with different activation methodologies. Particularly, it emphasized about the importance of treating the PAH to overcome the risk associated with the environment and humans due to its contamination.

Insight into the degradation of carbamazepine by electrochemical-pressure UV-activated peroxodisulphate process: kinetics, radicals, and degradation pathway

In this work, to improve the performance of peroxodisulphate-advanced oxidation, an electrochemical oxidation-assisted UV light-activated peroxodisulphate system (E/UV/PDS) was used to degrade carbamazepine. The degradation of carbamazepine by PDS, E/PDS, UV/PDS and E/UV/PDS systems was compared, and their synergistic effects were analysed. The influence of single factors, such as PDS addition, initial pH, DS voltage, target initial concentration, etc., on the degradation of the E/UV/PDS system was discussed, and the optimal degradation process parameters were given. The active substances were determined by free radical inhibition experiments, such as 1O2, SO 4 - ⋅ and ⋅ OH . It was proved that 1O2 contributes much more to the degradation of carbamazepine than SO 4 - ⋅ and ⋅ OH . The degradation pathway of carbamazepine was proposed. Finally, the degradation mechanism of carbamazepine in the E/UV/PDS system was speculated. The results indicate that the electrochemical combined with the E/UV/PDS system is of great potential application value in the removal of antibiotic drug pollution and environmental purification.

Role of biochar in superoxide-dominated dye degradation in catalyst-activated peroxymonosulphate process

In recent times, the application of biochar (BC) as an upcoming catalyst for the elimination of recalcitrant pollutants has been widely explored. Here, an iron loaded bamboo biochar activated peroxymonosulphate (PMS) process was tested for removing Congo red (CR) dye from water medium. The catalyst was synthesized using a green synthesis method using neem extracts and characterized using SEM, FTIR, and XRD. The effects of various operating parameters, including solution pH, catalyst dosage, and pollutant dosage, on dye degradation efficiency were examined. The results showed that at the optimized conditions of 300 mg L-1 PMS concentration, 200 mg L-1 catalyst dosage, and pH 6, about 89.7% of CR dye (initial concentration 10 ppm) was removed at 60 min of operation. Scavenging experiments revealed the significant contribution of O2•-, •OH, and 1O2 for dye degradation, with a major contribution of O2•-. The activation of PMS was mainly done by biochar rather than iron (loaded on biochar). The catalyst was highly active even after four cycles.

Development of persulfate-based advanced oxidation processes to remove synthetic azo dyes from aqueous matrices

Azo dyes are largely used in many industries and discharged in large volumes of their effluents into the aquatic environment giving rise to non-esthetic pollution and health-risk problems. Due to the high stability of azo dyes in ambient conditions, they cannot be abated in conventional wastewater treatment plants. Over the last fifteen years, the decontamination of dyeing effluents by persulfate (PS)-based advanced oxidation processes (AOPs) has received a great attention. In these methods, PS is activated to be decomposed into sulfate radical anion (SO4•-), which is further partially hydrolyzed to hydroxyl radical (•OH). Superoxide ion (O2•-) and singlet oxygen (1O2) can also be produced as oxidants. This review summarizes the results reported for the discoloration and mineralization of synthetic and real waters contaminated with azo dyes covering up to November 2023. PS activation with iron, non-iron transition metals, and carbonaceous materials catalysts, heat, UVC light, photocatalysis, photodegradation with iron, electrochemical and related processes, microwaves, ozonation, ultrasounds, and other processes is detailed and analyzed. The principles and characteristics of each method are explained with special attention to the operating variables, the different oxidizing species generated yielding radical and non-radical mechanisms, the addition of inorganic anions and natural organic matter, the aqueous matrix, and the by-products identified. Finally, the overall loss of toxicity or partial detoxification of treated azo dye solutions during the PS-based AOPs is discussed.

Piezoelectric catalytic driven advanced oxidation process using two-dimensional metal dichalcogenides for wastewater pollutants remediation

The public and society have increasingly recognized numerous grave environmental issues, including water pollution, attributed to the rapid expansion of industrialization and agriculture. Renewable energy-driven catalytic advanced oxidation processes (AOPs) represent a green, sustainable, and environmentally friendly approach to meet the demands of environmental remediation. In this context, 2D transition metal dichalcogenides (TMDCs) piezoelectric materials, with their non-centrosymmetric crystal structure, exhibit unique features. They create dipole polarization, inducing a built-in electric field that generates polarized holes and electrons and triggers redox reactions, thereby facilitating the generation of reactive oxygen species for wastewater pollutant remediation. A broad spectrum of 2D TMDCs piezoelectric materials have been explored in self-integrated Fenton-like processes and persulfate activation processes. These materials offer a more simplistic and practical method than traditional approaches. Consequently, this review highlights recent advancements in 2D TMDCs piezoelectric catalysts and their roles in wastewater pollutant remediation through piezocatalytic-driven AOPs, such as Fenton-like processes and sulfate radicals-based oxidation processes.

In situ synthesis of oxygen-doped carbon quantum dots embedded in MIL-53(Fe) for efficient degradation of oxytetracycline

Introducing carbon quantum dots (CQDs) into photocatalysts is believed to boost the charge transfer rate and reduce charge complexation. Doping heteroatoms such as N, S, or P enable CQDs to have an uplifting electron transfer capability. However, the application of oxygen-doped CQDs to improve the performance of photocatalysts has rarely been reported. Herein, a type of carbon-oxygen quantum dots (COQDs) was in situ embedded into MIL-53(Fe) to aid peroxydisulfate (PDS)-activated degradation of oxytetracycline (OTC) under visible light irradiation. The successful embedding of COQDs was confirmed by XRD, FT-IR, XPS, SEM, and TEM techniques. Photoelectrochemical testing confirmed its better performance. The prepared COQDs1/MIL-53(Fe) showed 88.2% decomposition efficiency of OTC in 60 min, which was 1.45 times higher than that of pure MIL-53(Fe). In addition, the performance of the material was tested at different pH, OTC concentrations, catalyst dosing, and PDS dosing. It was also subjected to cyclic testing to check stability. Moreover, free radical trapping experiments and electron paramagnetic resonance were conducted to explore the possible OTC deterioration mechanism. Our work provides a new idea for the development of MOFs for water treatment and remediation.

A Comprehensive Review on Modification of Titanium Dioxide-Based Catalysts in Advanced Oxidation Processes for Water Treatment

It has become necessary to develop effective strategies to prevent and reduce water pollution as a result of the increase in dangerous pollutants in water reservoirs. Consequently, there is a need to design new catalyst materials to promote the efficiency of advanced oxidation processes (AOPs) in the field of wastewater treatment plant to ensure the mineralization of trace organic contaminants. A notable approach gaining attention involves the coupling of sulfate radicals-based AOPs to photocatalysis or electrocatalysis processes, aiming to achieve the complete removal of refractory contaminants into water and carbon dioxide. Titanium dioxide as metal oxide has received great attention for its catalytic application in water purification. TiO2 catalysts offer a multitude of advantages in AOPs. They are characterized by their high photocatalytic activity under both ultraviolet and visible light, making them environmentally friendly due to the absence of toxic byproducts during oxidation. Their versatility is remarkable, finding utility in various AOPs, from photocatalysis to photo-Fenton processes. TiO2's durability ensures long-lasting catalytic activity, which is crucial for continuous treatment processes, and their cost-effectiveness is particularly advantageous. Furthermore, their chemical stability allows it to withstand varying pH conditions. However, the large band gap energy and low electrical conductivity hinder the catalytic reaction effectiveness. This review aims to examine various approaches to enhance the catalytic performance of titanium dioxide, with the objective of enabling more efficient water purification methods.

CoFe2O4 as a source of Co(II) ions for imidacloprid insecticide oxidation using peroxymonosulfate: Influence of process parameters and surface changes

Nanometric cobalt magnetic ferrite (CoFe2O4) synthesized by distinct methods was used for in situ chemical activation of peroxymonosulfate (PMS) under neutral conditions to oxidize imidacloprid (IMD) insecticide. The effect of CoFe2O4 load (0.125-1.0 g L-1) and PMS concentration (250-1000 μM) was investigated as well as the influence of phosphate buffer and Co(II) ions. PMS activation by Co(II) ions, including those leached from CoFe2O4 (>50 μg L-1), exhibited a strong influence on IMD oxidation and, apparently, without substantial contributions from the solid phase. Within the prepared solid materials (i.e., using sol-gel and co-precipitation methods), high oxidation rates (ca. 0.5 min-1) of IMD were attained in ultrapure water. Phosphate buffer had no significant influence on the IMD oxidation rate and level, however, its use and solution pH have shown to be important parameters, since higher PMS consumption was observed in the presence of buffered solutions at pH 7. IMD byproducts resulting from hydroxylation reactions and rupture of the imidazolidine ring were detected by mass spectrometry. At optimum conditions (0.125 g L-1 of CoFe2O4 and 500 μM of PMS), the CoFe2O4 nanoparticles exhibited an increase in the charge transfer resistance and an enhancement in the surface hydroxylation after PMS activation, which led to radical (HO● and SO4●-) and nonradical (1O2) species. The latter specie led to high levels of IMD oxidation, even in a complex water matrix, such as simulated municipal wastewater at the expense of one-order decrease in the IMD oxidation rate.

Antibiotic removal from synthetic and real aqueous matrices by peroxymonosulfate-based advanced oxidation processes. A review of recent development

The widespread use of antibiotics for the treatment of bacteriological diseases causes their accumulation at low concentrations in natural waters. This gives health risks to animals and humans since it can increase the damage of the beneficial bacteria, the control of infectious diseases, and the resistance to bacterial infection. Potent oxidation methods are required to remove these pollutants from water because of their inefficient abatement in municipal wastewater treatment plants. Over the last three years in the period 2021-September 2023, powerful peroxymonosulfate (PMS)-based advanced oxidation processes (AOPs) have been developed to guaranty the effective removal of antibiotics in synthetic and real waters and wastewater. This review presents a comprehensive analysis of the different procedures proposed to activate PMS-producing strong oxidizing agents like sulfate radical (SO4•-), hydroxyl radical (•OH, radical superoxide ion (O2•-), and non-radical singlet oxygen (1O2) at different proportions depending on the experimental conditions. Iron, non-iron transition metals, biochar, and carbonaceous materials catalytic, UVC, photocatalytic, thermal, electrochemical, and other processes for PMS activation are summarized. The fundamentals and characteristics of these procedures are detailed remarking on their oxidation power to remove antibiotics, the influence of operating variables, the production and detection of radical and non-radical oxidizing agents, the effect of added inorganic anions, natural organic matter, and aqueous matrix, and the identification of by-products formed. Finally, the theoretical and experimental analysis of the change of solution toxicity during the PMS-based AOPs are described.

Scientometric analysis of electrocatalysis in wastewater treatment: today and tomorrow

Electrocatalytic methods are valuable tools for addressing water pollution and scarcity, offering effective pollutant removal and resource recovery. To investigate the current status and future trends of electrocatalysis in wastewater treatment, a detailed analysis of 9417 papers and 4061 patents was conducted using scientometric methods. China emerged as the leading contributor to publications, and collaborations between China and the USA have emerged as the most frequent partnerships. Primary article co-citation clusters focused on oxygen evolution reaction and electrochemical oxidation, transitioning towards advanced oxidation processes ("persulfate activation"), and electrocatalytic reduction processes ("nitrate reduction"). Bifunctional catalysts, theoretical calculations, electrocatalytic combination technologies, and emerging contaminants were identified as current research hotspots. Patent analysis revealed seven types of electrochemical technologies, which were compared using SWOT analysis, highlighting electrochemical oxidation as prominent. The technological evolution presented the pathway of electro-Fenton to combined electrocatalytic technologies with biochemical processes, and finally to coupling with electrocoagulation. Standardized evaluation systems, waste resource utilization, and energy conservation were important directions of innovation in electrocatalytic technologies. Overall, this study provided a reference for researchers to understand the framework of electrocatalysis in wastewater treatment and also shed light on potential avenues for further innovation in the field.

Synthesis, characterization, and application of Cu-substituted LaNiO3 perovskites as photocatalysts and/or catalysts for persulfate activation towards pollutant removal

The presence of emerging contaminants in environmental aqueous matrices is an ever-growing problem, since conventional wastewater treatment methods fail to adequately remove them. Therefore, the application of non-conventional methodologies such as advanced oxidation processes is of great importance to tackle this modern problem. Photocatalysis as well as catalytic activation of persulfates are promising techniques in this field as they are capable of eliminating various emerging contaminants, and current research aims to develop new materials that can be utilized for both processes. In this light, the present study focused on the use of a simple sol-gel-combustion methodology to synthesize Cu-substituted LaNiO3 perovskite materials in an attempt to improve the photocatalytic and catalytic performance of pure LaNiO3, using molar ratios of Cu:Ni that have not been previously reported in the literature. The morphological, structural, and optical features of the synthesized materials were characterized by a series of analytical techniques (e.g., X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, diffuse reflectance spectroscopy, etc.). Also, their performance as photocatalysts, persulfate anion activators and simultaneously as photocatalysts/persulfate anion activators (hybrid) was evaluated by conducting laboratory-scale experiments using phenol (phenolics) as a model emerging contaminant. Interestingly, the results revealed that LaCu0.25Ni0.75O3 exhibited the best efficiency in all the applied processes, which was mainly attributed to the introduction of oxygen vacancies in the structure of the substituted material. The contribution of selected reactive species in the hybrid photocatalytic/catalytic experiments utilizing LaCu0.25Ni0.75O3 as a (photo)catalyst was investigated using appropriate scavengers, and the results suggested that singlet oxygen is the most dominant. Additionally, the stability of all synthesized perovskites was assessed by monitoring the concentration of the leached Cu and/or Ni cations at the end of every applied process. Finally, the reusability of LaCu0.25Ni0.75O3 was evaluated in three consecutive catalytic cycles using the hybrid experiment methodology, as this process demonstrated the best efficiency in terms of phenolics removal, and the results were rather promising.

Flowing Liquid-Based Triboelectric Nanogenerator Performance Enhancement with Functionalized Polyvinylidene Fluoride Membrane for Self-Powered Pulsating Flow Sensing Application

Pulsating flow, a common term in industrial and medical contexts, necessitates precise water flow measurement for evaluating hydrodynamic system performance. Addressing challenges in measurement technologies, particularly for pulsating flow, we propose a flowing liquid-based triboelectric nanogenerator (FL-TENG). To generate sufficient energy for a self-powered device, we employed a fluorinated functionalized technique on a polyvinylidene fluoride (PVDF) membrane to enhance the performance of FL-TENG. The results attained a maximum instantaneous power density of 50.6 µW/cm2, and the energy output proved adequate to illuminate 10 white LEDs. Regression analysis depicting the dependence of the output electrical signals on water flow revealed a strong linear relationship between the voltage and flow rate with high sensitivity. A high correlation coefficient R2 within the range from 0.951 to 0.998 indicates precise measurement accuracy for the proposed FL-TENG. Furthermore, the measured time interval between two voltage peaks precisely corresponds to the period of pulsating flow, demonstrating that the output voltage can effectively sense pulsating flow based on voltage and the time interval between two voltage peaks. This work highlights the utility of FL-TENG as a self-powered pulsating flow rate sensor.

Carbon and hydrogen isotopic evidence for atrazine degradation by electro-activated persulfate: Radical contributions and comparisons with heat-activated persulfate

The activation ways of persulfate (PS) were dominate for pollutant degradation and energy consumption. For the first time, this research compared electro-activated PS and heat-activated PS from the perspective of isotope fractionation, in order to "fingerprinted" and precisely interpretate reaction contributions and degradation pathways. As results, PS can be electrochemically activated with atrazine (ATZ) removal rates of 84.8% and 88.8% at pH 4 and 7. The two-dimensional isotope plots (ɅC/H) values were 6.20 at pH 4 and 7.46 at pH 7, rather different from that of SO4·- -dominated process with ɅC/H value of -4.80 at pH 4 and -23.0 at pH 7, suggesting the weak contribution of SO4·-. ATZ degradation by electro-activated PS was controlled by direct electron transfer (DET) and ·OH radical, and ·OHPS (derived from PS activation) played the crucial role with contributing rate of 63.2%-69.1%, while DET and ·OHBDD (derived from electrolysis of H2O) contributed to 4.5-7.9% and 23.0%-30.8%, respectively. This was different from heat activation of PS, of which the latter was dominated by SO4·- with contributions of 83.9%-100%. The discrepant dominating reactive oxygen species should be responsible for their different degradation capabilities and pathways. This research provided isotopic interpretations for differences of PS activation mode, and further efforts can be made to realize the selective degradation by enhancing the specific reaction process.

Effect of UV/peroxymonosulfate pretreatment on disinfection byproduct (DBP) formation during post-chlorination of humic acid

UV/peroxymonosulfate (UV/PMS) is a promising advanced oxidation technology in water treatment. This study aimed to investigate the impact of UV/PMS on humic acid (HA) and the influence of PMS dosage, pretreatment time, pH pretreatment, nitrate, nitrite, ammonium, and bicarbonate influencing factors on disinfection byproduct (DBP) formation during post-chlorination. With increased PMS dosage or pretreatment time, the UV/PMS treatment significantly reduced ultraviolet absorbance and increased mineralization. It altered the fractional constituent as humic substances were gradually transformed into building blocks and low-molecular-weight acids. However, most DBP formation increased initially and then decreased after subsequent chlorination. Rising nitrate or nitrite concentrations markedly promoted halonitromethane (HNM) formation. The presence of ammonia had a more significant impact on dichloroacetonitrile (DCAN) formation. Bicarbonate in UV/PMS pretreatment increased carbonated disinfection byproduct (C-DBP) formation, whereas it had a negligible impact on nitrogenous disinfection byproduct (N-DBP) formation. The present study revealed the impact of a series of influencing factors on DBP formation in UV/PMS reaction systems, providing comprehensive insights on applying UV/PMS in actual practice.

Removal of oxytetracycline from water by S-doped MIL-53(Fe): Synergistic effect of surface adsorption and persulfate activation

In this study, a novel catalyst based on MIL-53(Fe) was synthesized and modified through sublimed sulfur (S-MIL-53(Fe)) to induce a synergistic effect of surface adsorption and persulfate activation. The S-doped modification not only increased the surface area but also accelerated the electron transfer process of the iron cycle. The performance of the newly synthesized S-MIL-53(Fe) adsorptive catalyst was evaluated by chemical adsorption and peroxydisulfate (PDS) activated removal of an emerging pollutants, oxytetracycline (OTC). The S-MIL-53(Fe) adsorptive catalyst was able to adsorb 61.7% of OTC after 120 min, and the removal efficiency reached 84.8% within 5 min after PDS dosing. The boosting effect of sulfur on the system was confirmed by characterization analysis and experimental testing. Even after 7 cycles, the removal efficiency of S-MIL-53(Fe) (69.0%) for OTC remained superior to that of pure MIL-53(Fe) (25.1%). Additionally, the adsorption kinetics and adsorption isotherm model of the material were investigated. The possible OTC degrading process was proposed based on radical quenching and electron paramagnetic resonance (EPR). This study provides a feasible way to fabricate an S-doped MIL-53(Fe) adsorptive catalyst for the remediation of antibiotics-containing wastewater.

Degradation studies of bisphenol S by ultrasound activated persulfate in aqueous medium

The degradation of recalcitrant organic pollutants by sulphate radical (SO4•-) represents one of the most recent developments in oxidation-based water treatment. In most cases, persulfate (PS) acts as a precursor of sulphate radicals. This study employed ultrasound-activated PS to generate reactive species, facilitating the degradation of bisphenol S (BPS), a well-known contaminant of emerging concern (CECs). An ultrasound with a frequency of 620 kHz and 80 W power was utilised for the degradation studies. The applied oxidation system successfully resulted in the complete degradation of BPS in both pure and real environmental water samples. Additionally, the Chemical oxygen demand (COD) was reduced to an acceptable limit in both matrices, with a reduction of 85 % in pure water and 73 % in river water. The degradation was monitored by varying chemical parameters such as pH, inorganic ions, and organics concentration. The results indicate that under specific pH conditions, the degradation efficiency followed the order of pH 3 > 4 > 7 > 11. The presence of coexisting matrices suppressed the efficiency by scavenging the reactive species. Utilizing high-resolution mass spectrometry (HRMS) analysis, this study identified seven intermediate products during identified during the degradation of BPS. Furthermore, a comprehensive mechanism has been deduced for the transformation and degradation process. All the results presented in this study underscore the applicability of the US/PS system in the removal of CECs.

Efficient degradation of tetrabromobisphenol A using peroxymonosulfate oxidation activated by a novel nano-CuFe2O4@coconut shell biochar catalyst

In this study, a novel bimetallic complexation-curing nucleation-anaerobic calcination method was developed to synthesize a nano-CuFe2O4@coconut shell biochar (CuFe2O4@CSBC) catalyst to activate peroxymonosulfate for degradation of tetrabromobisphenol A (TBBPA). The reaction processes of the TBBPA on CuFe2O4@CSBC have been investigated using in situ characterization and metal leaching. The effects of initial reaction conditions and degradation mechanism were investigated. Greater than 99% degradation of TBBPA at 10 mg L-1 was achieved in 30 min under the condition of pH 11, a total organic carbon removal rate of up to 70.67% was achieved and the degradation efficiency was 90% after 5 cycles of CuFe2O4@CSBC use. The degradation was in a second-order reaction at a constant of 0.797 M-1 min-1 (R2 = 0.993). The degradation was attributed to the main active species (SO4·-≈·OH < 1O2), and the surface active site of CuFe2O4@CSBC was the key role. The degradation process involved three main degradation pathways. Path A: ·OH attacked the C-Br bonds (TBBPA→TriBBPA→DBBPA→MBBPA→BPA); Path B: Hydroxylation and decarboxylation; Path C: Dehydrocoupling of TBBPA. What's more, the practical application of the system was very positive, achieved >77% degradation in sewage and industrial wastewater.

Degradation of xanthene-based dyes by photoactivated persulfate: experimental and computational studies

Dyes are naked-eye detectable even at low concentration levels and can cause environmental damage when released into aquatic effluents; therefore, methods for removing the residual color from the aquatic media are always a current issue. In this paper, degradation of three xanthene dyes, Rhodamine B, Eosin Y, and Sodium Fluorescein, using photoactivated persulfate was evaluated at pH 3.0 and 11.0. The dyes' degradation followed a pseudo-first-order reaction. Although the solution is completely decolorized in 40 min at pH 3.0, achieving 75% mineralization requires a longer reaction time of 180 min. Furthermore, GC-MS analyses indicate that degradation products are mainly low-molecular weight acids, CO2 and H2O. Experiments carried out in dark and under UV irradiation showed substantial contribution of radical (SO4•- and HO•) and non-radical pathways to dye degradation in both pH. Additionally, to get more insights into the degradation pathways, HOMO-LUMO energy gaps of the dyes were calculated by DFT using MPW1PW91/MidiXo level of theory and, in general, the lower the bandgap, the faster the degradation. Fukui functions revealed that the preferential sites to radical attack were the xanthene or the benzoate portion depending on the pH, wherein attack to the xanthene ring provided better kinetic and mineralization results.

A co-precipitation route for the preparation of eco-friendly Cu-Al-layered double hydroxides with efficient tetracycline degradation

The construction of novel efficient catalysts for the treatment of organic pollutants in the aqueous environment is essential. The lamellar-like Cu-Al layered double hydroxides (CuAl-LDHs) with various mole ratios were synthesized by a simple route of co-precipitation, and the corresponding degradation characteristic was tested for the removal of tetracycline (TC) using PMS activation. The degradation efficiency of TC over CuAl-LDHs increased up to 93% within 10 min for the Cu/Al mole ratio of 3:1 and almost not changed at a higher mole ratio. For further calcining the optimal catalyst at 300 ℃, the degradation efficiency of TC was found to be increased to 96%. Sulfuric radicals and singlet oxygen were analyzed to be the main reason for the change in degradation characteristics, which was proved by radical quenching experiments and electron paramagnetic resonance technique. The parameters including PMS concentration, catalyst dosage, and reaction temperature on the TC degradation as well as the degradation mechanism for PMS activation were elaborated. The best proportion of CuAl-LDHs owned splendid stability and catalytic activity after reusing, which showed enormous potential in practical application.

Sequential treatment of landfill leachate by electrocoagulation/aeration, PMS/ZVI/UV and electro-Fenton: Performance, biodegradability and toxicity studies

This study presents a systematic study on sequential treatment of highly resistant landfill leachate by electrocoagulation (EC)/aeration, sulfate radical advanced oxidation process (SR-AOP) and electro-Fenton (EF). In case of SR-AOP, peroxymonosulfate (PMS) catalyzed by zero valent iron (ZVI) and ultraviolet irradiation (UV) system was developed. Treatment process was optimized in respect to COD removal. Analysis of results revealed that sequential application of EC/aeration, PMS/ZVI/UV, and EF processes provide an extraordinary performance and meet the environmental regulations. The source of iron for EF process was provided from previous process reducing the cost of sequential process. Separately, EC/aeration (inlet COD = 4040 mg/L), PMS/ZVI/UV (inlet COD = 1560 mg/L), and EF (inlet COD = 471 mg/L) removed 61, 69 and 82% of COD respectively. Overall, sequential processes of EC/aeration, PMS/ZVI/UV and EF could remove the COD, TOC and ammonia of the landfill leachate around 98%, 93% and 94%, respectively. The comparison of different sequences of following processes indicated that current configuration (EC/aeration-PMS/ZVI/UV-EF) could meet the discharge standards. Furthermore, humification degree was significantly improved after oxidative processes. Biodegradability study was also performed by means of BOD/COD, average oxidation state (AOS), and Zahn-Wellens test, and the best results associated with these indices were obtained 0.56, 2.37, and over 98%, respectively. Phytotoxicity of leachate was remarkably reduced and the final effluent can be considered as a non-phytotoxic wastewater.

Formation, toxicity, and mechanisms of halonitromethanes from poly(diallyl dimethyl ammonium chloride) during UV/monochloramine disinfection in the absence and presence of bromide ion

Bromide ion (Br^-) is known as a prevalent component in water environments, which exhibits significant impacts on halonitromethanes (HNMs) formation. This study was performed to explore and compare the formation, toxicity, and mechanisms of HNMs from poly(diallyl dimethyl ammonium chloride) (PDDACl) in the absence and presence of Br^- in the UV/monochloramine (UV/NH₂Cl) disinfection process. The results showed that chlorinated HNMs were found in the absence of Br^-, while brominated (chlorinated) HNMs and brominated HNMs were found in the presence of Br^-. Furthermore, the peaks of total HNMs were promoted by 2.0 and 2.4 times, respectively when 1.0 and 2.0 mg L^-1 Br^- were added. Also, the peaks of total HNMs were enhanced with the increase of the NH₂Cl dosage, which were reduced with the increase of pH. It should be noted that Br^- induced higher toxicity of HNMs, and the cytotoxicity and genotoxicity of HNMs with the addition of 2.0 mg L^-1 Br^- were 78.0 and 3.7 times those without the addition of Br^-, respectively. Meanwhile, both the reaction mechanisms of HNMs produced from PDDACl were speculated in the absence and presence of Br^-. Finally, different HNMs species and yields were discovered in these two real water samples compared to those in simulated waters. These findings of this work will be conducive to understanding the significance of Br^- affecting HNMs formation and toxicity in the disinfection process.

Pulsed versus direct current electrochemical co-catalytic peroxymonosulfate-based system: Elevated degradation and energy efficiency with enhanced oxidation mechanisms

In this work, the pulsed electrochemical (PE) system was investigated to activate peroxymonosulfate (PMS) with the addition of Fe(III) to achieve efficient degradation of sulfamethoxazole (SMX) with reduced energy consumption, in comparison with the direct current (DC) electrochemical system. The operational conditions of PE/PMS/Fe(III) system were optimized as 4 kHz pulse frequency, 50% duty cycle, and pH 3, at which 67.6% reduction of energy consumption and enhanced degradation performance were achieved compared to the DC/PMS/Fe(III) system. Results of electron paramagnetic resonance spectroscopy analysis and quenching and chemical probe experiment revealed the presence of ^•OH, SO₄^•-, and ¹O₂ in the system, with ^•OH being the dominant role. The concentrations of these active species were averagely 15 ± 1% higher in the PE/PMS/Fe(III) system than those of the DC/PMS/Fe(III) system. Identification of SMX byproducts was achieved based on high resolution mass spectrometry analysis to predict the degradation pathways. The SMX byproducts could eventually be eliminated by the PE/PMS/Fe(III) system with extended treatment time. Overall, the PE/PMS/Fe(III) system was demonstrated with high energy and degradation performance, and is appear to be an robust strategy for practical treatment of wastewater.

Degradation of tartrazine by Oxone® in the presence of cobalt based catalyst supported on pillared montmorillonite - Efficient technology even in extreme conditions

The catalytic degradation of hazardous organic contaminants in industrial wastewater is a promising technology. Reactions of tartrazine, the synthetic yellow azo dye, with Oxone® in the presence of catalyst in strong acidic condition (pH 2), were detected by using UV-Vis spectroscopy. In order to extend the applicability profile of Co-supported Al-pillared montmorillonite catalyst an investigation of Oxone® induced reactions were performed in extreme acidic environment. The products of the reactions were identified by liquid chromatography-mass spectrometry (LC-MS). Along with the catalytic decomposition of tartrazine induced by radical attack (confirmed as unique reaction path under neutral and alkaline conditions), the formation of tartrazine derivatives by reaction of nucleophilic addition was also detected. The presence of derivatives under acidic conditions slowed down the hydrolysis of tartrazine diazo bond in comparison to the reactions in neutral environment. Nevertheless, the reaction in acidic conditions (pH 2) is faster than the one conducted in alkaline conditions (pH 11). Theoretical calculations were used to complete and clarify the mechanisms of tartrazine derivatization and degradation, as well as to predict the UV-Vis spectra of compounds which could serve as predictors of certain reaction phases. ECOSAR program, used to estimate toxicological profile of compounds to aquatic animals, indicated an increase in the harmfulness of the compounds identified by LC-MS as degradation products from the reaction conducted for 240min. It could be concluded that an intensification of the process parameters (higher concentration of Oxone®, higher catalyst loading, increased reaction time, etc.) is needed in order to obtain only biodegradable products.

Degradation of atrazine by electroactivation of persulfate using FeCuO@C modified composite cathode: Synergistic activation mechanism

In sulfate radical-based advanced oxidation processes (SR-AOPs), high-efficiency and perdurable materials have drawn considerable interest for use as cathodes, which can effectively degrade refractory organic contaminants through the synergistic electro-activation and transition metal activation of persulfate (PS). Here, the FeCuO@C modified composite cathode (FeCuO@C/AGF) was synthesized via the solvothermal and thermal treatment method based on the CuFe-MOF-74 structure, and the electro-activation PS process (EC/FeCuO@C/AGF/PS) was developed to effectively remove atrazine (ATZ). The surface morphology, electrochemical characteristics, chemical composition, crystal structure, and electrode surface wettability of FeCuO@C/AGF were investigated. It was found that the proposed EC/FeCuO@C/AGF/PS process can successfully remove 100% of ATZ in 20 min at a low current density (2 mA cm^-2) and a low PS concentration (0.4 mM), and PS is successfully activated by combining the electrical and transition metal synergistic activation. The FeCuO@C/AGF cathode exhibits outstanding catalytic functionality over a broad pH range (2-9) and remains stable over five successive cycles. Additionally, the active species involved in the reaction as well as the potential ATZ degradation reaction mechanisms and pathways are discussed. Electrochemical oxidation is a process in which both radicals (SO₄^·-, ·OH, and O₂^·-) and non-radical (¹O₂) participate in the degradation of ATZ. The intermediates of the ATZ degradation process were studied upon the toxicity changing, and the toxicity of the intermediates was found to be reduced during degradation. These results present a novel approach toward the establishment of an effective and reliable electrode in SR-AOPs that can efficiently treat pesticide wastewater.

Promoted elimination of metronidazole in ferrous ions activated peroxydisulfate process by gallic acid complexation

We applied gallic acid (GA) as the complexing agent to stabilizing the regeneration of Fe²⁺ during the Fe²⁺/peroxydisulfate (PDS) Fenton-like reaction for promoting the removal of metronidazole (MTZ). This research evaluated the elimination of MTZ by optimizing the dose of GA and Fe²⁺ and pH condition. MTZ removal reached 83% at the GA: Fe²⁺ molar ratio of 1:1 (30 μM) and initial pH 5 and 6.2 after 120 min, and the kinetics showed two degradation phases (k_obs1 = 0.09636 for the rapid stage and k_obs2 = 0.01056 for the slow stage). The Fe²⁺ and GA complexes could expand the range of pH applicability and effectively stabilize the regeneration of Fe²⁺, which ultimately promoted the decontamination of MTZ. Sulfate radical (SO₄^.-), hydroxyl radicals, and singlet oxygen were proved to exist in this ternary system and contribute to MTZ removal, and SO₄^.- played the dominant role. Furthermore, the possible pathways and mechanisms for MTZ degradation were proposed, and the simulation result indicated that the toxicity of degradation intermediates of MTZ were declined. The GA assisted Fe²⁺/PDS system provided an improved promising advanced oxidation process for organic wastewater disposal.

A Comparison Study between Wood Flour and Its Derived Biochar for the Enhancement of the Peroxydisulfate Activation Capability of Fe3O4

In this study, both wood flour (WF) and wood flour-derived biochar (WFB) were used as supports for Fe3O4 to activate peroxydisulfate (PDS). The role of different carriers was investigated emphatically from the aspects of catalyst properties, the degradation kinetics of bisphenol A (BPA), the effects of important parameters, and the generation of reactive oxygen species (ROS). Results showed that both WF and WFB could serve as good support for Fe3O4, which could control the release of iron into solution and increase the specific surface areas (SSAs). The WFB/Fe3O4 had stronger PDS activation capability than WF/Fe3O4 mainly due to the larger SSA of WFB/Fe3O4 and the PDS activation ability of WFB. Both radical species (•OH and SO4•−) and non-radical pathways, including 1O2 and high-valent iron-oxo species, contributed to the degradation of BPA in the WFB/Fe3O4–PDS process. Moreover, the WFB/Fe3O4 catalyst also showed stronger ability to control the iron release, better reusability, and higher BPA mineralization efficiency than WF/Fe3O4.

The Potential of Spent Coffee Grounds @ MOFs Composite Catalyst in Efficient Activation of PMS to Remove the Tetracycline Hydrochloride from an Aqueous Solution

The efficient removal of Tetracycline Hydrochloride (TC) from wastewater, which is a difficult process, has attracted increasing attention. Aiming to synchronously achieve the goal of natural waste utilization and PMS activation, we have combined the MOFs material with waste coffee grounds (CG). The catalytic activity of the CG@ZIF-67 composite in the TC removal process was thoroughly evaluated, demonstrating that the TC removal rate could reach 96.3% within 30 min at CG@ZIF-67 composite dosage of 100 mg/L, PMS concertation of 1.0 mM, unadjusted pH 6.2, and contact temperate of 293.15 K. The ¹O₂ and ·SO₄^- in the CG@ZIF-67/PMS/TC system would play the crucial role in the TC degradation process, with ¹O₂ acting as the primary ROS. The oxygen-containing functional groups and graphite N on the surface of CG@ZIF-67 composite would play a major role in efficiently activating PMS and correspondingly degrading TC. In addition, the CG@ZIF-67/PMS/TC system could withstand a wide pH range (3-11). The application of CG in preparing MOF-based composites will provide a new method of removing emerging pollutants from an aqueous solution.