Mechanistic investigation of ciprofloxacin recovery by magnetite-imprinted chitosan nanocomposite: Isotherm, kinetic, thermodynamic and reusability studies

Photocatalytic degradation of antibiotics by N-doped carbon nanoflakes-nickel ferrite composite derived from algal biomass

This work reports the synthesis of nickel ferrite (NiFe) nanoparticles, N-doped mesoporous carbon nanoflakes (NCF) and novel nickel ferrite-carbon nanoflakes (NiFe@NCF) nanocomposite using solvothermal method. NCF was derived from a cyanobacterial consortium consisting of Anabaena, Lyngbya and Weistiellopsis, rich in carbon and nitrogen. The synthesized nanoparticles were used as heterogeneous photocatalyst for degradation of two harmful water pollutants, ciprofloxacin (CIP) and levofloxacin (LEV). 99.91% LEV and 98.86% CIP were degraded within 50 and 70 min of visible light irradiation using NiFe@NCF following pseudo first order kinetics. This improved efficiency of the nanocomposite may be attributed to its higher surface area, reduction of band gap (from 2.42 to 2.19 eV), more active sites as well as charge carrier mobility with decreasing agglomeration tendency of the magnetic nickel nanoparticles upon being embedded on NCF. N-doping improves light harvesting property, retards charge recombination and extends as well as delocalises ᴨ-conjugated system resulting in enhanced photocatalytic activity. The scavenging experiments and EPR analysis reveal that O2-• and •OH are the main active species taking part in the degradation process. The material performs well within a wide range of pH and can be effectively used up to 5 repetitive cycles. A feasible photocatalytic degradation mechanism of the antibiotics against NiFe@NCF nanocomposite is also put forwarded along with their possible degradation pathways from LCMS studies.

Chitosan hydrogels enriched with bioactive phloroglucinol for controlled drug diffusion and potential wound healing

We report a facile strategy to prepare chitosan (CS) hydrogels that eliminates the need for chemical crosslinking for advanced biomedical therapies. This approach gives controlled properties to the hydrogels by incorporating a natural bioactive phenolic compound, phloroglucinol (PG), into their microstructure. The adsorption of PG onto CS chains enhanced the hydrogels' antioxidant activity by up to 25 % and resulted in a denser, more entangled structure, reducing the pore size by 59 μm while maintaining porosity above 94 %. This allowed us to finely adjust pore size and swelling capacity. These structural properties make these hydrogels well-suited for wound healing dressings, promoting fibroblast proliferation and exhibiting excellent hemocompatibility. Furthermore, to ensure the versatility of these hydrogels, herein, we demonstrate their potential as drug delivery systems, particularly for dermal infections. The drug release can be controlled by a combination of drug diffusion through the swollen hydrogel and relaxation of the CS chains. In summary, our hydrogels leverage the synergistic effects of CS's antibacterial and antifungal properties with PG's antimicrobial and anti-inflammatory attributes, positioning them as promising candidates for biomedical and pharmaceutical applications, more specifically in advanced wound healing therapies with local drug delivery.

Carbon-Supported Nanocomposite Synthesis, Characterization, and Application as an Efficient Adsorbent for Ciprofloxacin and Amoxicillin

The existence of antibiotics in the environment has recently raised serious concerns about their possible hazards to human health and the water ecosystem. In the current study, an activated carbon-supported nanocomposite, AC-CoFe2O3, was synthesized by a coprecipitation method, characterized, and then applied to adsorb different drugs from water. The synthesized composites were characterized by using energy-dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, Brunauer-Emmett-Teller plots, and scanning electron microscopy. The adsorption of both Ciprofloxacin (Cipro) and Amoxicillin (Amoxi) antibiotics on the composite followed the pseudo-second-order kinetic model (R2 = 0.9981 and 0.9974 mg g-1 min-1, respectively). Langmuir isotherm was the best-fit model showing 312.17 and 217.76 mg g-1 adsorption capacities for Ciprofloxacin and Amoxicillin, respectively, at 333 K. The negative Gibbs free energy (ΔG°) specified the spontaneity of the method. The positive change in the enthalpy (ΔH) indicated that the adsorption process was assisted by higher temperatures. The different optimized parameters were pH, contact time, adsorbent weight, concentration, and temperature. The maximum adsorption of Cipro was found to be 98.41% at pH 12, while for Amoxi, it was 89.09% at pH 2 at 333 K. The drugs were then successfully determined from natural water samples at optimized conditions using these nanocomposites.

Emerging iron-based mesoporous materials for adsorptive removal of pollutants: Mechanism, optimization, challenges, and future perspective

Iron-based materials (IBMs) have shown promise as adsorbents due to their unique physicochemical properties. This review provides an overview of the different types of IBMs, their synthesis methods, and their properties. Results found in the adsorption of emerging contaminants to a wide range of IBMs are discussed. The IBMs used were evaluated in terms of their maximum uptake capacity, with special consideration given to environmental conditions such as contact time, solution pH, initial pollutant concentration, etc. The adsorption mechanisms of pollutants are discussed taking into account the results of kinetic, isotherm, thermodynamic studies, surface complexation modelling (SCM), and available spectroscopic data. A current overview of molecular modeling and simulation studies related to density functional theory (DFT), surface response methodology (RSM), and artificial neural network (ANN) is presented. In addition, the reusability and suitability of IBMs in real wastewater treatment is shown. The review concludes with the strengths and weaknesses of current research and suggests ideas for future research that will improve our ability to remove contaminants from real wastewater streams.

New chitosan-biochar composite derived from agricultural waste for removing sulfamethoxazole antibiotics in water

This study aims to develop a new chitosan-biochar composite derived from agricultural waste for removing sulfamethoxazole (SMX) antibiotics in water. Biochar was prepared from orange peel (OB) and spent coffee grounds (SCB). To fabricate chitosan-biochar composites, chitosan and biochar were crosslinked with glutaraldehyde. Results showed that pH, adsorbent dosage, time, temperature, and initial concentrations have a significant impact on the SMX adsorption. The adsorption data was better described by Langmuir (with good regression) than Freundlich model. The highest adsorption capacity (Q_max) of SMX on OB, SCB, CTS-OB, and CTS-SCB were 3.49, 7.65, 7.24, and 14.73 mg/g, respectively. The Freundlich constant (K_F) values for adsorption capacity were 1.66, 1.91, 2.57, and 5.57 (mg^1-nLⁿ/g), respectively, for OB, SCB, CTS-OB, and CTS-SCB. Ion exchange, π bonding, hydrogen bonding and pore filling, were proposed as dominant mechanisms of SMX removal process.

Adsorption of fluoroquinolone antibiotics onto ferrihydrite under different anionic surfactants and solution pH

To date, little information is available regarding the impacts of the widespread anionic surfactants on the adsorption behaviors of antibiotics onto typical iron oxides. Herein, we have investigated the effects of two typical surfactants (sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (SDBS)) on the adsorption of two widely used antibiotics (i.e., levofloxacin (LEV) and ciprofloxacin (CIP)) onto ferrihydrite. Results of kinetic experiments showed that the adsorption of antibiotics was well fitted by the pseudo-second-order kinetic models, indicating that the adsorption process might be controlled by chemisorption. The affinity of ferrihydrite toward CIP was greater than that toward LEV, which was ascribed to the higher hydrophobicity of CIP than LEV. Both surfactants enhanced antibiotic adsorption owing to SDS or SDBS molecules as bridge agents between ferrihydrite particles and antibiotics. Interestingly, the extent of the enhanced effects of surfactants on antibiotic adsorption declined as the background solution pH increased from 5.0 to 9.0, which was mainly due to the weaker hydrophobic interactions between antibiotics and the adsorbed surfactants on the iron oxide surfaces as well as the greater electrostatic repulsion between the anionic species of antibiotics and the negatively charged ferrihydrite particles at higher pH. Together, these findings emphasize the importance of widespread surfactants for illustrating the interactions between fluoroquinolone antibiotics and iron oxide minerals in the natural environment.

Recent advances in nanomaterials based sustainable approaches for mitigation of emerging organic pollutants

Emerging organic pollutants (EOPs) are a category of pollutants that are relatively new to the environment and recently garnered a lot of attention. The majority of EOPs includes endocrine-disrupting chemicals (EDCs), antibiotic resistance genes (ARGs), pesticides, dyes and pharmaceutical and personal care products (PPCPs). Exposure to contaminated water has been linked to an increase in incidences of malnutrition, intrauterine growth retardation, respiratory illnesses, liver malfunctions, eye and skin diseases, and fatalities. Consequently, there is a critical need for wastewater remediation technologies which are effective, reliable, and economical. Conventional wastewater treatment methods have several shortcomings that can be addressed with the help of nanotechnology. Unique characteristics of nanomaterials (NMs) make them intriguing and efficient alternative in wastewater treatment strategies. This review emphasis on the occurrence of divers emerging organic pollutants (EOPs) in water and their effective elimination via different NMs based methods with in-depth mechanisms. Furthermore, it also delves the toxicity assessment of NMs and critical challenges, which are crucial steps for practical implementations.

Adsorption of caffeine using steel wastes

Caffeine is the most widespread active pharmaceutical compound in the world, generally studied as a tracer of human pollution, since caffeine levels in surface water correlate with the anthropogenic load of domestic wastewater. This work investigated the use of different steel wastes named as SW-I, SW-II, SW-II, SW-IV, SW-V, and SW-VI in the adsorption of caffeine. These materials were pretreated and characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and point of zero charge. The samples are mainly composed of iron (hematite and magnetite). The caffeine adsorption test indicated that SW-VI (steel slag dust) is the most efficient and promising (removal around 51.68%) in relation to the other residues, which it was selected for further studies. Equilibrium time was reached within 96 h of contact between the adsorbent and the adsorbate, with removal of 84.00%, 81.09%, and 73.19% for the initial concentrations of 10 mg L-1, 20 mg L-1, and 30 mg L-1 of caffeine. The pseudo-first-order, pseudo-second-order, and Elovich models presented a good fit to the experimental data. However, the pseudo-first order model described better the experimental behavior. Adsorption isotherms were performed at three temperatures (298, 308, and 318 K). The maximum adsorption capacity was 17.46 ± 2.27 mg g-1, and experimental data were better fitted by the Sips isotherm. Values of ΔG° and parameters equilibrium of the models of Langmuir, Sips, and Temkin were calculated from the standard enthalpies and standard entropies estimated. The values of ΔG° were negative for the temperatures studied indicating that the adsorption process is viable and spontaneous. Negative values for ΔH° were also found, indicating that the process of caffeine adsorption by SW-VI is an exothermic process (0 to -40 kJ mol-1). Thus, the adsorption of caffeine by SW-VI is a physical process. The SW-VI material showed economic viability and promising for the adsorption of caffeine in aqueous media.

Chitosan-based Dy2O3/CuFe3O4 bio-nanocomposite development, characterization, and drug release kinetics

Chitosan (CS)/metal oxide (MO) nano-carriers have recently attracted attention due to their great integration into several biomedical applications. Herein, CS and dysprosium oxide based bio-nanocomposites (Dy₂O₃/CuFe₃O₄/CS) were prepared using a citrate sol-gel route for biomedical settings at large and drug delivery, in particular. The chemical structure, average crystallite size, and surface morphology of Dy₂O₃/CuFe₃O₄/CS bio-nanocomposites were characterized using spectroscopic techniques, including FT-IR, PXRD, and SEM. The prepared nano composite's drug loading or release kinetics were investigated by FT-IR, zeta potential (ZP), and ultraviolet-visible spectroscopy (UV-Vis). In the FT-IR spectrum, the peaks in the range of 800-400 cm^-1 confirmed the formation of meta-oxides, while amide bands at 1661 and 1638 cm^-1 revealed the existence of CS in the bio-nanocomposite. The peaks at 2θ = 35.46 and 28.5, 39.4 indicated the presence and chemical interaction of Dy₂O₃ and CuFe₃O_4, respectively. The crystallite size was <20 nm. The model drug used in the loading and in vitro release assays was ciprofloxacin hydrochloride. Ciprofloxacin's CF stretch caused a modest peak to be seen at 1082 cm^-1 and changed in zeta potential value from 7.90 mV to 8.88 mV endorsing that the drug had been loaded onto the nanomaterial. The loading efficiency (%) of CIP onto the composite was from 25 to 30 %, calculated from optical density measurements. Different kinetic models, such as zero-order, first-order, Higuchi, Hixon-Crowell, and Korsmeyer-Peppas, were determined to confirm the drug release mechanism. The percent (%) of drug release from the surface of Dy₂O₃/CuFe₃O₄/CS in PBS (pH 7.4), acidic (pH 2.2) and basic (pH 9.4) dissolution media were found to be 70, 28 and 20 %, respectively. Drug kinetics showed that mainly the release is fickian type followed "Fick's law of diffusion", slightly deviated from fickian release (dissolution-dependent system). Korsmeyer-Peppas (R² 0.9773, n < 0.4) and Higuchi's (R² 0.9846) models were the best for fitting controlled drug release data. The results revealed that the Dy₂O₃/CuFe₃O₄/CS bio-nanocomposite has good potential for a controlled drug delivery system.

Dual immobilization of magnetite nanoparticles and biosilica within alginate matrix for the adsorption of Cd(II) from aquatic phase

The adsorption of cadmium ions by magnetite (Fe3O4)@biosilica/alginate (MBA nano-hybrid) was the main aim of the present investigation. Herein, MBA nano-hybrid was synthesized via chemical precipitation technique. As-synthesized MBA nano-hybrid was characterized using FT-IR, FESEM and XRD analyzes. Based on the results, the maximum adsorption capacity of the adsorbent for the removal of Cd(II) was obtained at the initial pH of 7.0. At the initial Cd(II) concentration of 40 mg/L, increasing the reaction time to 180 min led to the Cd adsorption of 35.36 mg/g. Since the removal of Cd(II) after the reaction time of 60 min was insignificant, the reaction time of 60 min was considered as optimum reaction time for performing the experimental runs. According to the results, Langmuir isotherm and pseudo-second order kinetic models were the best fitted models with high correlation coefficients (R2 > 0.99). The results of thermodynamic study indicated exothermic (positive ΔH°) and spontaneous nature (negative ΔG°) of the adsorption of Cd(II) on the surface of MBA nano-hybrid. Negligible reduction in the adsorption capacity of the nano-hybrid was observed (16.57%) after fifth experimental runs, indicating high reusability potential of the as-synthesized nano-hybrid adsorbent.

Sustainable adsorptive removal of antibiotic residues by chitosan composites: An insight into current developments and future recommendations

During COVID-19 crisis, water pollution caused by pharmaceutical residuals have enormously aggravated since millions of patients worldwide are consuming tons of drugs daily. Antibiotics are the preponderance pharmaceutical pollutants in water bodies that surely cause a real threat to human life and ecosystems. The excellent characteristics of chitosan such as nontoxicity, easy functionality, biodegradability, availability in nature and the abundant hydroxyl and amine groups onto its backbone make it a promising adsorbent. Herein, we aimed to provide a comprehensive overview of recent published research papers regarding the removal of antibiotics by chitosan composite-based adsorbents. The structure, ionic form, optimum removal pH and λmax of the most common antibiotics including Tetracycline, Ciprofloxacin, Amoxicillin, Levofloxacin, Ceftriaxone, Erythromycin, Norfloxacin, Ofloxacin, Doxycycline, Cefotaxime and Sulfamethoxazole were summarized. The development of chitosan composite-based adsorbents in order to enhance their adsorption capacity, reusability and validity were presented. Moreover, the adsorption mechanisms of these antibiotics were explored to provide more information about adsorbate-adsorbent interactions. Besides the dominant factors on the adsorption process including pH, dosage, coexisting ions, etc. were discussed. Moreover, conclusions and future recommendations are provided to inspire for further researches.

Understanding the factors affecting adsorption of pharmaceuticals on different adsorbents - A critical literature update

Remediation of emerging pharmaceutically active compounds (PhACs) as micropollutants in wastewater is of foremost importance as they can cause extremely detrimental effects on life upon bioaccumulation and generation of drug-resistance microorganisms. Presently used physicochemical treatments, such as electrochemical oxidation, nanofiltration and reverse osmosis, are not feasible owing to high operating costs, incomplete removal of contaminants along with toxic by-products formation. Adsorption with the utilization of facile and efficient nanoparticulate adsorbents having distinctive properties of high surface area, excellent adsorption capacity, ability to undergo surface engineering and good regeneration displays great potential in this aspect along with the incorporation of nanotechnology for effective treatment. The application of such nanosorbents provides optimal performance under a wide range of physicochemical conditions, decreased secondary pollution with reduced mechanical stress along with excellent organic compound sequestration capacity, which in turn improves the quality of potable water in a sustainable way compared to current treatments. The present review intends to consolidate the range of factors that affect the process of adsorption of different PhACs on to various nanosorbents and also highlights the adsorption mechanism aiding in the retrieval.

Preparation of a Three-Dimensional Porous Graphene Oxide-Kaolinite-Poly(vinyl alcohol) Composite for Efficient Adsorption and Removal of Ciprofloxacin

Because of the widespread presence of antibiotics in water, soil, and other environments, they pose great potential risks to the environment, threatening human and animal health. In this study, graphene oxide-kaolinite homogeneous dispersion was prepared by simple liquid phase exfoliation. The three-dimensional (3D) porous graphene oxide-kaolinite-poly(vinyl alcohol) composites were prepared by the cross-linking of poly(vinyl alcohol) and the formation of ice crystals during the freezing-drying process. Three influencing factors [adsorbent dosage, ciprofloxacin (CIP) initial concentration, and time] of CIP adsorption and removal were systematically analyzed by the response surface method. The order of significance for response values (CIP removal rate) was adsorbent dosage > CIP initial concentration > time. The 3D porous material showed good adsorption capacity of CIP, the theoretical maximum adsorption capacity was 408.16 mg/g, and it had good recyclability. By Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy analysis, it was found the composite adsorbs CIP by hydrogen bonding and π-π interaction. In conclusion, the graphene oxide-kaolinite-poly(vinyl alcohol) porous composite is a good candidate for efficient antibiotic wastewater treatment.

A Removable Artificial Cell Wall for Withstanding Ciprofloxacin

The pollution of antibiotics in aquaculture environment is increasingly serious, and excessive antibiotics will kill the probiotics in aquaculture feed. How to improve the viability of probiotics in the antibiotics-contaminated environment is of significance. In this study, a new strategy for protecting Saccharomyces cerevisiae cells in situ against antibiotics is constructed based on cell surface engineering technology by putting on wearable protective layers for cells. The protective layer is constructed around cellular surface via the self-assembly of coacervate microdroplets that consist of carboxymethyl chitosan and carboxyl dextran. Without affecting the cell viability, the protective layer can grasp ciprofloxacin and decrease the contact of ciprofloxacin to cells and consequently improve the survival rate of cells when exposing to ciprofloxacin. This work highlights a facile strategy to establish removable artificial cell wall by biodegradable polysaccharides for improving the productivity of probiotics in antibiotic environments.

Synthesis and characterization of core-shell magnetic molecularly imprinted polymers for selective extraction of allocryptopine from the wastewater of Macleaya cordata (Willd) R. Br

A novel type of magnetic molecularly imprinted polymers (MMIP) as the solid-phase extraction sorbent was prepared, which can extract effectively the allocryptopine from the waster of Macleaya cordata (Willd) R. Br. In this study, MMIP was synthesized by using Fe₃ O₄ @SiO₂ , 4-vinyl-pyridine, ethylene glycol dimethacrylate, and allocryptopine, and these ingredients worked as magnetic core, functional monomer, cross-linker, and template, respectively. Concluded by the calculation of Gaussian 09 software, different ratio models of 4-vinyl-pyridine and allocryptopine were simulated, and the optimal ratio was 1:5 and the energy was -2205.34 kJ/mol. Transmission electron microscopy, vibration sample magnetometry, X-ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis were used to determine the morphology and structure of MMIP. Furthermore, the results of adsorption experiments indicated that MMIP had high selectivity, excellent recyclability, and good adsorption performance (9.86 mg/g, 298 K). The adsorption process was consistent with the Langmuir adsorption isotherm (R² > 0.98, 298 K) and pseudo-second-order kinetics model (R² > 0.99, 298 K). After six times adsorption-desorption experiments, the adsorption amount of MMIP only reduced to 8.5%. In the experiments of selective adsorption, MMIP has better adsorption properties for allocryptopine (ALL, C₂₁ H₂₃ NO₅ ) than those having the same functional group. The limit of detection (LOD) was 0.4 μg/mL. The relative standard deviation ranged from 0.09% to 0.72%. The recovery of allocryptopine in samples ranged from 93.60% to 106.19%. In addition, the synthesized complex had a certain adsorption effect on allocryptopine separating from the wastewater of Macleaya cordata (Willd) R. Br.

Antibiotics in wastewater from multiple sources and surface water of the Yangtze River in Chongqing in China

Antibiotic contamination attracts growing concerns because of their deleterious effects on the ecosystem and human health. In this study, 43 antibiotics in wastewater from a variety of sources and water of the Yangtze River in Chongqing City in western China were measured. Thirty compounds were detected, and their concentrations were highest in leachates from the municipal solid waste treatment facilities (landfills and incineration plants) with total concentrations of 3584-57,106 ng/L. The total concentrations in influents of municipal and industrial wastewater treatment plants (WWTPs) were comparable (401-7994 ng/L versus 640-8945 ng/L). The concentrations in raw sewage from swine farms (with a total of 10,219-39,195 ng/L) and poultry farms (1419-36,027 ng/L) were noticeably higher than those from other farms (54.0-5516 ng/L). Fluoroquinolones were the dominant antibiotics contributing over 50% in all the sources, and sulfonamides and imidazole fungicides contributed 3.2-34%, whereas tetracyclines and macrolides had minor contributions. The overall antibiotic removal rates were highest in solid waste treatment facilities (88% on average), comparable between municipal and industrial WWTPs (61%), and lowest in animal farms (39%). The mass loads to the investigated municipal WWTPs via influent wastewater ranged from 7.80 to 1531 kg/year (53.2-2482 μg/day per capital). The influent mass loads to the industrial WWTPs and farms were 3.7-50 kg/year and 0.9-5437 g/year, respectively. We estimated that the mass inventories of antibiotics from these sources to the environment via effluent discharges were approximately 2044 kg for municipal WWTPs, 61 kg for industrial WWTPs, and 34 kg for animal farms in the whole city. Antibiotic concentrations in the Yangtze River water were substantially low (< 492 ng/L, with a mean of 57.8 ng/L) suggesting dissipation during the movement.

Deep eutectic solvent as an efficient modifier of low-cost adsorbent for the removal of pharmaceuticals and dye

Waste from biomass was used to prepare a low-cost biochar-clay hybrid adsorbent. The hybrid adsorbent was synthesised by combining Kaolin with biomass (Vitex doniana), thereafter, modified with Deep Eutectic Solvent (DES). The materials were characterised using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectrometry (FTIR), Thermal gravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET), also, pHpzc of the materials were studied. The resultant adsorbents were used for both column and batch adsorption of organic pollutants; dye (Acid Blue 74; AB74) and pharmaceuticals (ciprofloxacin; CIP and acetaminophen; ACTE). Column adsorption capacity, effect of pollutant concentration and effect of flow rate were studied, also, the column was modelled using Thomas, Yoon-Nelson and Adams-Bohart model. Furthermore, batch adsorption experiments were performed, effect of change in pH, time, dose and concentration were studied. Batch adsorption data were fitted with isotherm and kinetic models. The experiment showed tremendous increase in adsorption capacity when the hybrid adsorbent (HYD) was modified with DES (HYD-DES). Acid Blue 74 on HYD-DES has the highest column sorption capacity followed by ciprofloxacin and acetaminophen. Adsorption was favoured at pH range of 2-10 for both AB74 and ACTE as there is no significant changes in the % removal performance, while adsorption was best at pH 6 and above for CIP. AB74 and CIP are best described by Langmuir isotherm, whereas ACTE adsorption was best explained by Freundlich isotherm equilibrium. The DES modified HYD has shown it can be effectively utilised as possible adsorbent for adsorbing organic dyes and pharmaceuticals.

Immobilization of Lipase A from Candida antarctica onto Chitosan-Coated Magnetic Nanoparticles

In this communication, lipase A from Candida antarctica (CALA) was immobilized by covalent bonding on magnetic nanoparticles coated with chitosan and activated with glutaraldehyde, labelled CALA-MNP, (immobilization parameters: 84.1% ± 1.0 for immobilization yield and 208.0 ± 3.0 U/g ± 1.1 for derivative activity). CALA-MNP biocatalyst was characterized by X-ray Powder Diffraction (XRPD), Fourier Transform Infrared (FTIR) spectroscopy, Thermogravimetry (TG) and Scanning Electron Microscope (SEM), proving the incorporation of magnetite and the immobilization of CALA in the chitosan matrix. Besides, the immobilized biocatalyst showed a half-life 8-11 times higher than that of the soluble enzyme at pH 5-9. CALA showed the highest activity at pH 7, while CALA-MNP presented the highest activity at pH 10. The immobilized enzyme was more active than the free enzyme at all studied pH values, except pH 7.