Fast and efficient phosphate removal on lanthanum-chitosan composite synthesized by controlling the amount of cross-linking agent

Lanthanum-calcium bimetallic-modified attapulgite- chitosan hydrogel beads for efficient phosphate removal from water: Performance evaluation, mechanistic and life cycle assessment

Phosphorus is a critical factor in the control of eutrophication. We developed a three-dimensional porous, bimetallic-modified adsorbent La-Ca-CS/ATP to remove excess phosphate from water. Langmuir model showed that the theoretical adsorption capacity of La-Ca-CS/ATP was up to 123 mg P/g. The amount of La and Ca leached by La-Ca-CS/ATP was small, and the adsorption of 36.08 mg P/g was maintained during the five cycles of La-Ca-CS/ATP. The La-Ca-CS/ATP adsorption mechanism mainly involved surface precipitation, ligand exchange, electrostatic attraction, and inner-sphere complexation. Molecular dynamics demonstrated that La and Ca had complementary effects on binding sites and energy barriers within the range of 0.5-0.7 nm and 1.2-2 nm, enhancing the adsorption effect of La-Ca-CS/ATP. The life cycle assessment results showed that adding calcium could help reduce the environmental impact of lanthanum and chitosan. The production of La-Ca-CS/ATP adsorbed 73.88 P mg/g and emitted 24.73 kg CO2 eq, which was less than other adsorbents.

A novel sponge composite of chitosan-sodium tripolyphosphate-melamine for anionic dye Orange II removal

Since the potential carcinogenic, toxic and non-degradable dyes trigger serious environmental contamination by improper treatment, developing novel adsorbents remains a major challenge. A novel high efficiency and biopolymer-based environmental-friendly adsorbent, chitosan‑sodium tripolyphosphate-melamine sponge (CTS-STPP-MS) composite, was prepared for Orange II removing with chitosan as raw material, sodium tripolyphosphate as cross-linking agent. The composite was carefully characterized by SEM, EDS, FT-IR and XPS. The influence of crosslinking conditions, dosage, pH, initial concentration, contacting time and temperature on adsorption were tested through batch adsorption experiments. CTS-STPP-MS adsorption process was exothermic, spontaneous and agreed with Sips isotherm model accompanying the maximum adsorption capacity as 948 mg∙g-1 (pH = 3). Notably, the adsorption performance was outstanding for high concentration solutions, with a removal rate of 97 % in up to 2000 mg∙L-1 OII solution (100 mg sorbent dosage, 50 mL OII solution, pH = 3, 289.15 K). In addition, the adsorption efficiency yet remained 97.85 % after 5 repeated adsorption-desorption cycles. The driving force of adsorption was attributed to electrostatic attraction and hydrogen bonds which was proved by adsorption results coupled with XPS. Owing to the excellent properties of high-effective, environmental-friendly, easy to separate and regenerable, CTS-STPP-MS composite turned out to be a promising adsorbent in contamination treatment.

Simultaneous removal of phosphate and tetracycline using LaFeO3 functionalised magnetic biochar by obtained ultrasound-assisted sol-gel pyrolysis: Mechanisms and characterisation

Excessive phosphate and tetracycline (TC) contaminants pose a serious risk to human health and the ecological environment. As such exploring the simultaneous adsorption of phosphate and TC is garnering increasing attention. In this study, an efficient lanthanum ferrate magnetic biochar (FLBC) was synthesised from crab shells using an ultrasound-assisted sol-gel method to study its performance and mechanisms for phosphate and TC adsorption in aqueous solutions in mono/bis systems. According to the Langmuir model, the developed exhibited a maximum adsorption capacity of 65.62 mg/g for phosphate and 234.1 mg/g for TC (pH:7.0 ± 0.1, and 25 °C). Further, it exhibited high resistance to interference and pH suitability. In practical swine wastewater applications, whereby the concentrations of phosphate and TC are 37 and 19.97 mg/L, respectively, the proposed material demonstrated excellent performance. In addition, electrostatic adsorption, chemical precipitation and ligand exchange were noted to be the main mechanisms for phosphate adsorption by FLBC, whereas hydrogen bonding and π-π interaction were the main adsorption mechanisms for TC adsorption. Therefore, this study successfully prepared a novel and efficient adsorbent for phosphate and TC.

Recent advances in removal of inorganic anions from water by chitosan-based composites: A comprehensive review

Chitosan is a modified natural carbohydrate polymer that has been found in the exoskeletons of crustaceans (e.g., lobsters, shrimps, krill, barnacles, crayfish, etc.), mollusks (octopus, oysters, squids, snails), algae (diatoms, brown algae, green algae), insects (silkworms, beetles, scorpions), and the cell walls of fungi (such as Ascomycetes, Basidiomycetes, and Phycomycetes; for example, Aspergillus niger and Penicillium notatum). However, it is mostly acquired from marine crustaceans such as shrimp shells. Chitosan-based composites often present superior chemical, physical, and mechanical properties compared to single chitosan by incorporating the benefits of both counterparts in the nanocomposites. The tunable surface chemistry, abundant surface-active sites, facilitation synthesize and functionalization, good recyclability, and economic viability make the chitosan-based materials potential adsorbents for effective and fast removal of a broad range of inorganic anions. This article reviews the different types of inorganic anions and their effects on the environment and human health. The development of the chitosan-based composites synthesis, the various parameters like initial concentration, pH, adsorbent dosage, temperature, the mechanism of adsorption, and regeneration of adsorbents are discussed in detail. Finally, the prospects and technical challenges are emphasized to improve the performance of chitosan-based composites in actual applications on a pilot or industrial scale.

Polymer-based nanocomposite adsorbents for resource recovery from wastewater

Developing mitigation mechanisms for eutrophication caused by the uncontrolled release of nutrients is in the interest of the scientific community. Adsorption, being operationally simple and economical with no significant secondary pollution, has proven to be a feasible technology for resource recovery. However, the utility of adsorption often lies in the availability of effective adsorbents. In this regard, polymer-based nanocomposite (PNC) adsorbents have been highly acclaimed by researchers because of their high surface area, multiple functional groups, biodegradability, and ease of large-scale production. This review paper elaborates on the functionality, adsorption mechanisms, and factors that affect the adsorption and adsorption-desorption cycles of PNC adsorbents toward nutrient resources. Moreover, this review gives insight into the application of recovered nutrient resources in soil amendment.

Recovery of Phosphate(V) Ions from Water and Wastewater Using Chitosan-Based Sorbents Modified-A Literature Review

Over the past two decades, there has been increasing interest in the use of low-cost and effective sorbents in water treatment. Hybrid chitosan sorbents are potential materials for the adsorptive removal of phosphorus, which occurs in natural waters mainly in the form of orthophosphate(V). Even though there are numerous publications on this topic, the use of such sorbents in industrial water treatment and purification is limited and controversial. However, due to the explosive human population growth, the ever-increasing global demand for food has contributed to the consumption of phosphorus compounds and other biogenic elements (such as nitrogen, potassium, or sodium) in plant cultivation and animal husbandry. Therefore, the recovery and reuse of phosphorus compounds is an important issue to investigate for the development and maintenance of a circular economy. This paper characterizes the problem of the presence of excess phosphorus in water reservoirs and presents methods for the adsorptive removal of phosphate(V) from water matrices using chitosan composites. Additionally, we compare the impact of modifications, structure, and form of chitosan composites on the efficiency of phosphate ion removal and adsorption capacity. The state of knowledge regarding the mechanism of adsorption is detailed, and the results of research on the desorption of phosphates are described.

Optimization of Removal of Phosphate from Water by Adsorption Using Biopolymer Chitosan Beads

The need for clean water is the most basic human right. Water scarcity will be one important environmental problem of all countries in the future. Phosphate is a harmful matter for public health and the environment. In this study, the removal of phosphate from water by chitosan, which is an environmentally friendly material, was investigated. Chitosan adsorbent spheres were prepared for phosphate separation from water by adsorption, which is a feasible method. The effects of phosphate concentration, adsorbent dosage, and operation time on the removal were investigated. The removal increased with acid concentration and adsorbent amount. The maximum adsorption capacity of chitosan beads is 87.26 mg/g. Adsorption behavior of the chitosan beads were examined by Langmuir and Freundlich isotherms and pseudo-first and second-order kinetic models. The adsorption process was optimized by the response surface method (RSM). Trial version of Design Expert® 12.0 was used in the study. It has been understood as a result of the RSM statistical analysis that higher phosphate removal values would be obtained by increasing the amount of adsorbent. ANOVA analysis showed that adsorbent dosage had the biggest effect on removal of phosphate using chitosan beads prepared for adsorption.

Sustainable Multi-Network Cationic Cryogels for High-Efficiency Removal of Hazardous Oxyanions from Aqueous Solutions

It is still a challenge to develop advanced materials able to simultaneously remove more than one pollutant. Exclusive cationic composite double- and triple-network cryogels, with adequate sustainability in the removal of Cr₂O₇^2- and H₂PO₄^- oxyanions, were developed in this work starting from single-network (SN) sponges. Chitosan (CS), as the only polycation originating from renewable resources, and poly(N,N-dimethylaminoethylmethacrylate) (PDMAEMA) and polyethyleneimine (PEI), as synthetic polycations, were employed to construct multi-network cationic composite cryogels. The properties of the composites were tailored by the cross-linking degree of the first network (SN5 and SN20, which means CS with 5 or 20 mole % of glutaraldehyde, respectively) and by the order of the successive networks. FTIR, SEM-EDX, equilibrium water content and compressive tests were used in the exhaustive characterization of these polymeric composites. The sorption performances towards Cr₂O₇^2- and H₂PO₄^- anions were evaluated in batch mode. The pseudo-first-order, pseudo-second-order (PSO) and Elovich kinetics models, and the Langmuir, Freundlich and Sips isotherm models were used to interpret the experimental results. The adsorption data were the best fitted by the PSO kinetic model and by the Sips isotherm model, indicating that the sorption mechanism was mainly controlled by chemisorption, irrespective of the structure and number of networks. The maximum sorption capacity for both oxyanions increased with the increase in the number of networks, the highest values being found for the multi-network sponges having SN5 cryogel as the first network. In binary systems, all sorbents preferred Cr₂O₇^2- ions, the selectivity coefficient being the highest for TN sponges. The high sorption capacity and remarkable reusability, with only a 4-6% drop in the sorption capacity after five sorption-desorption cycles, recommend these composite cryogels in the removal of two of the most dangerous pollutants represented by Cr₂O₇^2- and H₂PO₄^-.

Polymer-based nanocomposite adsorbents for resource recovery from wastewater

Adsorption is alternative technique for recovery of nutrient resources with no/less secondary pollution. PNC adsorbents are effective for removal and recovery of nutrient resources, and reusing nutrients as fertilizer could prevent eutrophication.

Phosphate Removal from Wastewater by Magnetic Amorphous Lanthanum Silicate Alginate Hydrogel Beads

It is of both fundamental and practical importance to develop effective adsorbents for removing phosphate from aqueous solutions continuously. In this study, magnetic amorphous lanthanum silicate alginate hydrogel beads (MALS-B) were prepared and used for phosphate removal. Mesoporous silica materials with highly ordered and hexagonal channel structures were synthesized from natural mineral rectorite (REC) at room temperature. On this basis, amorphous lanthanum silicate (ALS) was synthesized by theone-pot method using a silicon source from REC and a commercial lanthanum source. Further, MALS-B were synthesized from sodium alginate (SA) with ALS and Fe3O4 as the incorporated adsorbable and magnetic nanoparticles via a simple cross-linking method in CaCl2 solution. The synthesized hydrogel beads were characterized by various techniques. ALS and Fe3O4 existed relatively independently in MALS-B, where ALS provided adsorption sites and Fe3O4 provided magnetism. They played a synergistic role in phosphate removal. The saturation magnetization value of MALS-B was 17.38 emu/g, enabling theirfacile separation from aqueous solutions after phosphate adsorption. MALS-B exhibited a preferable adsorption capacity of 40.14 mg P/g for phosphorus compared to other hydrogel beads based on adsorption experiments. More significantly, MALS-B exhibited excellent selectivity for phosphate in aqueous solutions with various interfering ions and possessed a high affinity to phosphate in a wide pH range. MALS-B showed the treatment volume of 480 BV when effluent phosphate concentration was below 0.5 mg/L in fixed-bed column adsorption. The adsorption mechanism was also revealed. Our work demonstrates that MALS-B can serve as a promising adsorbent for continuous phosphate adsorption.

Cost-effective phosphorus removal from aqueous solution by a chitosan/lanthanum hydrogel bead: Material development, characterization of uptake process and investigation of mechanisms

Excessive phosphorus is one of the main reasons leading to eutrophication that causes severe ecosystem imbalance and negative human health impacts. In this study, several chitosan (CS)/lanthanum (La) hydrogel beads were first synthesized and tested for phosphorus removal. The stable cross-linked CS/La hydrogel bead prepared with the optimized conditions of 10 wt% La/CS and 1.5 mL of 5% glutaraldehyde demonstrated exceptional performance in the removal. It removed phosphate effectively from an aqueous solution in the pH range from 2 to 7. The complete phosphate uptake was achieved at contact time of 6 h under the completely mixing batch condition. The experimental maximum adsorption capacity of 107.7 mg g^-1 was observed at solution pH 4. The phosphate adsorption was well described by the Freundlich isotherm and the intraparticle surface diffusion model. Furthermore, the adsorbent was effectively regenerated and reused in a five-cycle adsorption-desorption operation. The removal of phosphate can be attributed to electrostatic attraction and ion exchange. Moreover, the bead was capable of removing heavy metals: copper, zinc and lead. This adsorbent may be served as a cost-effective material for the treatment of phosphorus-contaminated water so as to minimize the occurrence of eutrophication.

Chitosan based adsorbents for the removal of phosphate and nitrate: A critical review

The tremendous development in the industrial sector leads to discharging of the several types of effluents containing detrimental contaminants into water sources. Lately, the proliferation of toxic anions particularly phosphates and nitrates onto aquatic systems certainly depreciates the ecological system and causes a deadly serious problem. Chitosan (Cs) is one of the most auspicious biopolymer adsorbents that are being daily developed for removing of various contaminants from polluted water. This is due to its unparalleled benefits involving biocompatibility, non-toxicity, facile modifications and low-cost production. Nevertheless, chitosan displays considerable drawbacks including low adsorption capacity, low surface area and lack of reusability. Therefore, few findings have been established regarding the aptitude of modified chitosan-based adsorbents towards phosphate and nitrate anions. This review elaborates an overview for the current advances of modified chitosan based-adsorbent for phosphate and nitrate removal, in specific multivalent metals-modified chitosan, clays and zeolite-modified chitosan, magnetic chitosan and carbon materials-modified chitosan. The efforts that have been executed for enriching their adsorption characteristics as well as their possible adsorption mechanisms and reusability were well addressed. Besides, the research conclusions for the optimum adsorption conditions were also discussed, along with emphasizing the foremost research gaps and future potential trends that could motivate further research and innovation to find best solutions for water treatment problems facing the world.

Facile synthesis of Zr(IV)-crosslinked carboxymethyl cellulose/carboxymethyl chitosan hydrogel using PEG as pore-forming agent for enhanced phosphate removal

Zr(IV)-crosslinked carboxymethyl cellulose/carboxymethyl chitosan hydrogels were prepared using polyethylene glycol (PEG) as pore-forming agent. The hydrogels exhibited porous structure and the pore size increased with the PEG content. The obtained hydrogels were used as adsorbents for removal of phosphate from aqueous solutions. The hydrogel prepared with most amount of PEG displayed largest adsorption amount of phosphate. This result might be attributed to improvement of surface area and pore volume caused by introduction of PEG, which could boost exposure of adsorption sites in the hydrogel and enhance the diffusion of phosphate into interior of the hydrogel. The phosphate adsorption achieved equilibrium within 400 min and the removal process followed pseudo-second-order kinetic model. The maximum adsorption capacity was reached at pH = 2.0, and the adsorption capacity gradually increased with temperature. In the presence of coexisting anions, SO₄^2- ions exerted much more negative effect on phosphate adsorption than Cl^- and NO₃^- ions. The phosphate adsorption mechanism was related to electrostatic interaction, ligand exchange and ion exchange. Moreover, the hydrogel exhibited relatively stable adsorption capacity after six adsorption/desorption cycles. The present study presented a facile method for preparing an excellent hydrogel adsorbent for phosphate removal from aqueous solutions.