Contact forces in several TKA designs during squatting: A numerical sensitivity analysis

Internal rotational patellar resection and patella alta induced patellar maltracking in total knee arthroplasty: intraoperative measurement of the patellofemoral pressure

BACKGROUND

Anterior knee pain due to patellar maltracking following total knee arthroplasty (TKA) reduces patients' satisfaction. This study aimed to determine the patellofemoral pressure (PFP) in patients with favorable patellar tracking (FT) and impaired patellar tracking (IT) following TKA, the factors causing patellar maltracking, and the effect of lateral retinacular release (LRR) on patients with IT.

METHODS

Forty-four patients with varus knee osteoarthritis undergoing cruciate-retaining TKA were enrolled. After component implantation, patients with a separation of ≥ 2 mm of the patellar medial facet from the medial femoral trochlea throughout knee range of motion were classified into the IT group; meanwhile, the others were classified into the FT group. PFP was measured intraoperatively in three phases: (1) with the resurfaced patella (RP); (2) with the resurfaced patella and knee (RPK); and (3) when LRR was performed in IT (post-LRR). The PFPs at 0°, 90°, 120°, and 135° knee flexion were compared between FT and IT using the Mann-Whitney U test. Pairwise comparison of the PFP in IT between RPK and post-LRR was performed using the Wilcoxon signed-rank test. Correlations between PFP and pre- and postoperative radiographic parameters, such as hip-knee-ankle angle, lateral distal femoral angle, medial proximal tibial angle, anterior femoral offset, Insall-Salvati ratio (ISR), patellar tilt, and patellar resection angle (PRA), were evaluated using Spearman's rank correlation coefficients.

RESULTS

High lateral PFP in the knee flexion position led to patellar maltracking. Patients with IT (n = 24) had higher lateral and lower medial PFP than did patients with FT (n = 20) at 90°, 120°, and 135° knee flexion in RP and RPK. LRR in IT reduced the lateral PFP in the knee flexion position. PRA and ISR were correlated with the lateral PFP at no less than 90° in RP and RPK.

CONCLUSIONS

This study demonstrated that internal rotational patellar resection, which resulted in a thick medial patellar remnant and a thin lateral counterpart, and patella alta were the causative factors of high lateral PFP, which induced patellar maltracking after TKA. Surgeons should avoid internal rotational patellar resection to achieve FT and perform LRR in patients with patellar maltracking.

Enhancing the Unicompartmental Knee Arthroplasty Safety via Finite Element Analysis of Coronary Plane Alignment: A Case Report

Although Oxford unicompartmental knee arthroplasty is often used to successfully treat patients with knee osteoarthritis isolated at the medial compartment, we present a case of fracture just below the tibial keel caused by either a shift in medial loading position or an increased amount of tibial osteotomy. Finite element analysis was used to determine which factor was more important. First, a 3D-surface model of the patient's tibia and the implant shape were created using computed tomography-Digital Imaging and Communications in Medicine (CT-DICOM) data taken preoperatively. The finite element analysis found that following unicompartmental knee arthroplasty, the cortical stress (normal, 5.8 MPa) on the medial tibial metaphyseal cortex increased as the load point moved medially (3 and 12 mm medially: 7.0 and 10.7 MPa, respectively) but was mild with increased tibial bone resection (2 and 6 mm lower: 6.1 and 6.5 MPa, respectively). Implanting the femoral component more medially than the preoperative plan increases stresses in the medial cortex of the tibia and may cause fractures.

Finite element analysis in the optimization of posterior-stabilized total knee arthroplasty

Posterior-stabilized total knee arthroplasty (PS-TKA) is associated with high rates of satisfaction and functional recovery. This is notably attributed to implant optimization in terms of design, choice of materials, positioning and understanding of biomechanics. Finite elements analysis (FEA) is an assessment technique that contributed to this optimization by ensuring mechanical results based on numerical simulation. By close teamwork between surgeons, researchers and engineers, FEA enabled testing of certain clinical impressions. However, the methodological features of the technique led to wide variations in the presentation and interpretation of results, requiring a certain understanding of numerical and biomechanical fields by the orthopedic community. The present study provides an up-to-date review, aiming to address the following questions: what are the principles of FEA? What is the role of FEA in studying PS design in TKA? What are the key elements in the literature for understanding the role of FEA in PS-TKA? What is the contribution of FEA for understanding of tibiofemoral and patellofemoral biomechanical behavior? What are the limitations and perspectives of digital simulation and FEA in routine practice, with a particular emphasis on the "digital twin" concept? LEVEL OF EVIDENCE: V, expert opinion.

Validation of a novel finite-element model for evaluating patellofemoral forces and stress during squatting after posterior-stabilized total knee arthroplasty

INTRODUCTION

Several studies have documented the relationship between patellofemoral pain and patient dissatisfaction after total knee arthroplasty (TKA). However, few computer simulations have been designed to evaluate the patellofemoral joint during flexion. The aim of this study was to validate a new computational simulation, driven by forces and moments, and to analyze patellofemoral reaction forces and stress under squat loading conditions after TKA implantation.

HYPOTHESIS

This computational simulation of a squat using a model driven by forces and moments is comparable to in vitro and in silico data from the literature.

MATERIAL AND METHODS

We developed a finite element model of the lower limb after implantation of a fixed-bearing posterior-stabilized TKA. To simulate squat loading conditions when standing on both legs, an initial load of 130N was applied to the center of the femoral head. Quadriceps force, patellofemoral contact force and Von Mises stress on the patellar implant, tibiofemoral contact forces and pressure on the tibial insert, and post-cam contact force were evaluated from 0° to 100° of knee flexion.

RESULTS

Quadriceps force increased during flexion, up to 6 times the applied load. Von Mises stress on patellar implant increased up to 16MPa at 100° flexion. Tibiofemoral contact forces increased up to 415 N medially and 339 N laterally, with 64% distributed medially on the tibial insert. Post-cam contact started slightly before 70° of flexion.

DISCUSSION

In this simulation, tibiofemoral, patellofemoral and post-cam contact forces, and pressure distribution on the tibial insert were consistent with various published studies. This agreement suggests that computational simulation driven by forces and moments can reproduce squat loading conditions during knee flexion after TKA, without experimental kinematic data used to drive the simulation.

CONCLUSION

This study represents an initial step towards validating tibiofemoral and patellofemoral mechanical behavior under squat conditions, from this computational simulation driven by forces and moments. This model will help us better understand the influence of various implantation techniques on patellofemoral forces and stress during flexion.

LEVEL OF EVIDENCE

IV, biomechanical computational study.

Patella height influences patellofemoral contact and kinematics following cruciate-retaining total knee replacement

The role of patella height is discussed controversially in total knee arthroplasty (TKA). Therefore, this computational study aims to systematically analyze the biomechanical effect of different patella heights on patellofemoral (PF) forces and kinematics after cruciate-retaining (CR) TKA. We implemented a CR bicondylar TKA with a dome patellar button in a validated dynamic musculoskeletal multibody model of a male human knee joint. Retropatellar dynamics (contact force [N], shear force [N], patellar shift [mm], tilt [°], and rotation [°]) were evaluated during dual-limb squat motion (flexion from 0° to 90°) with simulated active muscle forces and the effects of different patella heights (Blackburne-Peel [BP] ratio of 0.39, 0.49, 0.65, 0.85, 1.01, and 1.1 were systematically examined). As active knee flexion increased, PF contact force also increased. Patella alta (BP = 1.1) resulted in higher PF contact forces compared to normal patella height (BP = 0.65) by up to 16%. Contrarily, patella baja was associated with decreased PF forces by 7%. Compared to patella baja (BP = 0.39), patella alta (BP = 1.1) considerably increased the contact force by up to 25%. Different patellar heights mainly affected PF shear forces during early knee flexion. Concerning PF kinematics, patella alta (BP = 1.1) yielded a greater lateral tilt of more than 4° and higher patellar rotation by up to 3° during deep knee flexion, compared to normal patella height (BP = 0.65). Our computational study indicates that patella alta is associated with the highest PF contact and shear force after the implantation of a CR bicondylar TKA. This should be considered in PF disorders following TKA.

Finite element analysis of malposition in bi-unicompartmental knee arthroplasty

PURPOSE

Bi-unicompartmental knee arthroplasty is a less invasive treatment than a total one, great advantage for the patient but more difficult for the surgeon because of the lower visibility during surgery; this can therefore lead to eventual small errors in cutting angles during the procedure. The aim of this study is to investigate the effects of these slight angle variations in terms of anterior-posterior slope for the lateral tibial tray.

METHODS

The geometries of the bones were acquired and uncemented fixed bearing metal-back UKAs virtually implanted in a finite elements environment. The lateral component was implanted in six different antero-posterior slope configurations (from - 5° to + 5° respect to medial component). Material properties for implant, bones and soft tissues were taken from the literature. A vertical compressive force of 2000 N was applied in full-extended configuration on the femur. Von Mises stress distribution in proximal tibia, load/pressure/contact area repartitions between the medial and lateral compartments was extracted as outputs.

RESULTS

Outcomes for 0° and - 3° configurations are acceptable, but the - 2° of slope configuration achieved the best ones in terms of stress on proximal tibia, load repartition, contact pressure distribution and shear component. Drastically different results are found for the  ± 5° configurations, presenting a level of unbalancing often associated with weak stability and failure over time.

CONCLUSIONS

Slight errors can happen during the surgery: performing the cut aiming to slightly posterior slopes during the surgery helps to minimize the chances of obtaining positive slopes that could lead to an unstable implant.

Tibial sagittal and rotational alignment reduce patellofemoral stresses in posterior stabilized total knee arthroplasty

Patellofemoral joint complications remain an important issue in total knee arthroplasty. We compared the patellofemoral contact status between cruciate-retaining and posterior-stabilized designs with varying degrees of tibial sagittal and rotational alignment using a computer simulation to ensure proper alignments in total knee arthroplasty. Knee kinematics, patellofemoral contact force and quadriceps force were computed using a musculoskeletal modeling program (LifeMOD/KneeSIM 2010; LifeModeler, Inc., San Clemente, California) during a weight-bearing deep knee bend. Two different posterior tibial slope (PTS)s (3° and 7°) and five different tibial tray rotational alignments (neutral, internal 5° and 10°, and external 5° and 10°) were simulated. Patellofemoral contact area and stresses were next computed using finite element analysis. The patellofemoral contact force for the posterior-stabilized design was substantially lower than the cruciate-retaining design after post-cam contact because of increasing femoral roll-back. Neutral rotational alignment of the tibial component resulted in smaller differences in patellofemoral contact stresses between cruciate-retaining and posterior-stabilized designs for PTSs of 3° or 7°. However, the patellar contact stresses in the cruciate-retaining design were greater than those in posterior-stabilized design at 120° of knee flexion with PTS of 3° combined with internal rotation of the tibial component. Our study provides biomechanical evidence implicating lower PTSs combined with internal malrotation of the tibial component and the resultant increase in patellofemoral stresses as a potential source of anterior knee pain in cruciate-retaining design.

Biomechanical Analysis of the Use of Stems in Revision Total Knee Arthroplasty

Adequate fixation is fundamental in revision total knee arthroplasty; consequently, surgeons must determine the correct set-up for each patient, choosing from numerous stem solutions. Several designs are currently available on the market, but there are no evidence-based quantitative biomechanical guideline yet. Therefore, several stems were designed and analyzed using a previously-validated finite-element model. The following parameters were studied: stem design characteristics (length and shape), added features (straight/bowed stem), fixation technique, and effect of slots/flutes. Bone stress and Risk of Fracture (RF) were analyzed in different regions of interest during a squat (up to 120°). For the femoral stem, the results indicated that all parameters influenced the bone stress distribution. The maximum von Mises stress and RF were always located near the tip of the stem. The long stems generated stress-shielding in the distal bone. Regarding the tibial stem, cemented stems showed lower micromotions at the bone-tibial tray interface and at the stem tip compared to press-fit stems, reducing the risk of implant loosening. The results demonstrated that anatomical shapes and slots reduce bone stress and risk of fracture, whereas flutes have the opposite effect; no relevant differences were found in this regard when alternating cemented and press-fit stem configurations. Cemented tibial stems reduce antero-posterior micromotions, preventing implant loosening.

Techniques to determine knee joint contact forces during squatting: A systematic review

This review article provides an overview of techniques used to determine human knee joint contact forces during squatting. The main two approaches are experimental and theoretical. Thigh calf contact has a significant effect on knee forces and should not be neglected. In this study, data were searched electronically and organized by techniques to find knee joint contact force during squatting theoretically and experimentally. There was a large variation in peak tibiofemoral (CV = 0.45) and patellofemoral (CV = 0.38) contact forces predicted theoretically. However, very little variation was observed between peak tibiofemoral contact forces (CV = 0.12) measured in vivo experimentally but measured knee joint force is available up to a limited knee flexion angle. There was a reduction in knee joint contact forces due to thigh calf contact. Literature of knee joint contact force prediction theoretically during squatting incorporating thigh calf contact force is very limited.

Bicompartmental, medial and patellofemoral knee replacement might be able to maintain unloaded knee kinematics

INTRODUCTION

Unicompartmental knee arthroplasty (UKA) and total knee arthroplasty (TKA) are standard procedures for treating knee joint arthritis. Neither UKA nor TKA seems to be optimally suited for patients with bicompartmental osteoarthritis that affects only the medial and patellofemoral compartments. A bicompartmental knee arthroplasty (BKA) was designed for this patient group. This study aimed to compare the effectiveness of a BKA and TKA in restoring the kinematics of the knee joint.

MATERIALS AND METHODS

In this in vitro study, three types of knee arthroplasties (BKA, posterior cruciate ligament-retaining, and posterior cruciate ligament-resecting TKA) were biomechanically tested in six freshly frozen human cadaveric specimens. Complete three-dimensional kinematics was analyzed for each knee arthroplasty during both passive and loaded conditions in a validated knee kinematics rig. Infrared motion capture cameras and retroreflective markers were used for recording data.

RESULTS

No significant differences could be found between the three types of arthroplasties. However, similar kinematic changes between BKA and a native knee joint were documented under passive conditions. However, in a weight-bearing mode, a significant decrease in femoral rotation during the range of motion was found in arthroplasties compared to the native knee, probably caused by contraction of the quadriceps femoris muscle, which leads to a decrease in the anterior translation of the tibia.

CONCLUSIONS

Kinematics similar to that of the natural knee can be achieved by BKA under passive conditions. However, no functional advantage of BKA over TKA was detected, which suggests that natural knee kinematics cannot be fully imitated by an arthroplasty yet. Further prospective studies are required to determine the anatomic and design factors that might affect the physiologic kinematics.

Kinematics and kinetics comparison of ultra-congruent versus medial-pivot designs for total knee arthroplasty by multibody analysis

Nowadays, several configurations of total knee arthroplasty (TKA) implants are commercially available whose designs resulted from clinical and biomechanical considerations. Previous research activities led to the development of the so-called medial-pivot (MP) design. However, the actual benefits of the MP, with respect to other prosthesis designs, are still not well understood. The present work compares the impact of two insert geometries, namely the ultra-congruent (UC) and medial-pivot (MP), on the biomechanical behaviour of a bicondylar total knee endoprosthesis. For this purpose, a multibody model of a lower limb was created alternatively integrating the two implants having the insert geometry discretized. Joint dynamics and contact pressure distributions were evaluated by simulating a squat motion. Results showed a similar tibial internal rotation range of about 3.5°, but an early rotation occurs for the MP design. Furthermore, the discretization of the insert geometry allowed to efficiently derive the contact pressure distributions, directly within the multibody simulation framework, reporting peak pressure values of 33 MPa and 20 MPa for the UC and MP, respectively. Clinically, the presented findings confirm the possibility, through a MP design, to achieve a more natural joint kinematics, consequently improving the post-operative patient satisfaction and potentially reducing the occurrence of phenomena leading to the insert loosening.

Quantifying Asymmetry between Medial and Lateral Compartment Knee Loading Forces using Acoustic Emissions

OBJECTIVE

Osteoarthritis is the most common type of knee arthritis that can be affected by excessive and compressive loads and can affect one or more compartments of the knee: medial, lateral, and patellofemoral. The medial compartment tends to be the most vulnerable to injuries and research suggests that a better understanding of the medial to lateral load distribution conditions could provide insights to the quantitative usage of knee compartments in activities of daily life.

METHODS

To that end, we present a novel method to quantify the directional bias of asymmetry between the medial and lateral compartment knee joint load by recording knee acoustical emissions and analyzing them using a deep neural network in a subject independent model. We placed four miniature contact microphones on the medial and lateral sides of the patella on both the left and right leg. We compared the handcrafted audio features with the automated features extracted from the convolutional autoencoder which is an unsupervised model that learns the comprehensive representation of the input to determine whether these automated features can better represent the signals characteristic in regard to the structural asymmetry of the knee joint. The input to the convolutional auto encoder (CAE) is a time-frequency representation and different types of these images such as spectrogram and scalogram are compared. We also compared the multi-sensor fusion approach with the performance of a single sensor to determine the robustness of using multiple sensors.

RESULTS

Using a representation learning based approach, we developed a subject independent classification model capable of classifying the asymmetry of the medial and lateral joint load across subjects (accuracy = 83%).

CONCLUSION

The result indicates that wavelet coherence which is the time-frequency correlation of two signals using a wavelet transform yields the best accuracy.

SIGNIFICANCE

These findings suggest that acoustic signals could potentially quantify the direction of medial to lateral load distribution which would broaden the implications for wearable sensing technology for monitoring cartilage health and factors responsible for cartilage breakdown and assessing appropriate rehabilitation exercises without overloading on one side.

[Biomechanical research on effects of pseudo-patella baja on stress of patellofemoral joint after total knee arthroplasty]

Objective

To investigate biomechanical effects of pseudo-patella baja on stress of patellofemoral joint after total knee arthroplasty (TKA) by using finite element analysis (FEA).

Methods

A series of CT and MRI of the left knee joint of two healthy volunteers and three-dimensional (3D) scanned data of TKA prosthesis were taken, and the 3D models of knee before and after TKA were established. The finite element model of pseudo-patella baja, normal patella, and alta patella after TKA were constructed by Insall-Salvafi (IS) ratio and Blackburne-Peel (BP) ratio. The load was applied along the direction of quadriceps femoris. After testing the validity of the finite element model, the high contact stress of patellofemoral joint was measured on the von Mise stress nephogram of pseudo-patella baja, normal patella, and alta patella after TKA when the knee flexion was 30°, 60°, and 90°. The average contact area was calculated according to two volunteers' data.

Results

On the finite element model of the normal patella after TKA with knee flexion 30°, 475 N pressure was applied along the direction of quadriceps femoris. The contact stress of patellofemoral joint was (1.29±0.41) MPa, which was similar to the results reported previously. The finite element model was valid. The von Mise stress nephogram showed that the stress mainly focused on the medial patellofemoral articular surface during knee flexion, and the contact point gradually moved up with the knee flexion deepened. The stress on the medial and lateral patellofemoral articular surface increased with the knee flexion deepened but decreased with the increase of patellar height. The effects of patellar height and knee flexion on the high contact stress of patellofemoral joint were similar among the finite element models after TKA based on the data of two volunteers. The high contact stress of patellofemoral joint increased with the knee flexion deepened in the same patellar height models ( P<0.05), but decreased with the increase of patellar height in the same knee flexion models ( P<0.05). The high contact stress of patellofemoral joint of pseudo-patella baja model was significantly higher than normal and alta patella models ( P<0.05). The average contact area of patellofemoral joint of pseudo-patella baja was bigger than normal and alta patella models with the knee flexion deepened.

Conclusion

The pseudo-patella baja after TKA has an important effect on the biomechanics of patellofemoral joint. Reserving the joint line and avoiding the occurrence of pseudo-patella baja can decrease the risk of anterior knee pain, patellar arthritis, and other complications caused by the increasing of contact stress of patellofemoral joint.

Total Knee Replacement: Subject-Specific Modeling, Finite Element Analysis, and Evaluation of Dynamic Activities

This study presents a semi-automatic framework to create subject-specific total knee replacement finite element models, which can be used to analyze locomotion patterns and evaluate knee dynamics. In recent years, much scientific attention was attracted to pre-clinical optimization of customized total knee replacement operations through computational modeling to minimize post-operational adverse effects. However, the time-consuming and laborious process of developing a subject-specific finite element model poses an obstacle to the latter. One of this work's main goals is to automate the finite element model development process, which speeds up the proposed framework and makes it viable for practical applications. This pipeline's reliability was ratified by developing and validating a subject-specific total knee replacement model based on the 6th SimTK Grand Challenge data set. The model was validated by analyzing contact pressures on the tibial insert in relation to the patient's gait and analysis of tibial contact forces, which were found to be in accordance with the ones provided by the Grand Challenge data set. Subsequently, a sensitivity analysis was carried out to assess the influence of modeling choices on tibial insert's contact pressures and determine possible uncertainties on the models produced by the framework. Parameters, such as the position of ligament origin points, ligament stiffness, reference strain, and implant-bone alignment were used for the sensitivity study. Notably, it was found that changes in the alignment of the femoral component in reference to the knee bones significantly affect the load distribution at the tibiofemoral joint, with an increase of 206.48% to be observed at contact pressures during 5° internal rotation. Overall, the models produced by this pipeline can be further used to optimize and personalize surgery by evaluating the best surgical parameters in a simulated manner before the actual surgery.

Large medial proximal tibial angles cause excessively medial tibiofemoral contact forces and abnormal knee kinematics following open-wedge high tibial osteotomy

BACKGROUND

Recurrent varus deformity and poor outcome sometimes occur following open-wedge high tibial osteotomy, but the mechanism remains unclear. The hypothesis of this study was that an excessively large medial proximal tibial angle with lateral joint surface inclination can worsen postoperative knee biomechanics.

METHODS

A computer-simulated knee model was validated based on a volunteer knee. Osteotomy models with medial proximal tibial angles ranging from 90° to 97° in 1° increments were developed. Varus alignment correction of the distal femur was performed in each model to maintain identical coronal alignment passing through a point 62.5% lateral to the tibial plateau. The peak tibiofemoral contact forces and knee kinematics were compared in each model during walking and squatting.

FINDINGS

All the osteotomy models demonstrated higher peak contact forces on the lateral tibiofemoral joints than on the medial tibiofemoral joints during walking. However, larger medial proximal tibial angles caused excessive increases in medial tibiofemoral contact forces, and the dominant tibiofemoral contact forces shifted to the medial side. Increased medial proximal tibial angles also caused progressive medial collateral ligament tension in knee flexion, but partial medial collateral ligament release effectively reduced medial tibiofemoral contact forces. Models with large medial proximal tibial angles showed nonphysiological roll-forward of the lateral femoral condyle during squatting and no screw-home movement around knee extension.

INTERPRETATION

Excessively large medial proximal tibial angles following open-wedge high tibial osteotomy resulted in increased medial tibiofemoral contact forces and abnormal knee kinematics during knee flexion due to medial joint line elevation and ligament imbalance.

Posterior tibial slope and anterior post-cam contact can change knee kinematics in extension in bi-cruciate stabilized total knee arthroplasty

Aims

This study aims to investigate the effects of posterior tibial slope (PTS) on knee kinematics involved in the post-cam mechanism in bi-cruciate stabilized (BCS) total knee arthroplasty (TKA) using computer simulation.

Methods

In total, 11 different PTS (0° to 10°) values were simulated to evaluate the effect of PTS on anterior post-cam contact conditions and knee kinematics in BCS TKA during weight-bearing stair climbing (from 86° to 6° of knee flexion). Knee kinematics were expressed as the lowest points of the medial and lateral femoral condyles on the surface of the tibial insert, and the anteroposterior translation of the femoral component relative to the tibial insert.

Results

Anterior post-cam contact in BCS TKA was observed with the knee near full extension if PTS was 6° or more. BCS TKA showed a bicondylar roll forward movement from 86° to mid-flexion, and two different patterns from mid-flexion to knee extension: screw home movement without anterior post-cam contact and bicondylar roll forward movement after anterior post-cam contact. Knee kinematics in the simulation showed similar trends to the clinical in vivo data and were almost within the range of inter-specimen variability.

Conclusion

Postoperative knee kinematics in BCS TKA differed according to PTS and anterior post-cam contact; in particular, anterior post-cam contact changed knee kinematics, which may affect the patient’s perception of the knee during activities.

Cite this article: Bone Joint Res 2020;9(11):761–767.

Change in knee biomechanics during squat and walking induced by a modification in TKA size

The purpose of this study is to analyze the effects of TKA under-dimensioning during daily activities. A regular ("control") size and an undersized design of the same fixed bearing asymmetric PS prosthesis were analyzed during walking and squat using finite element analysis. The two models showed similar internal-external rotations and antero-posterior displacements during both activities. Slightly higher displacements, wider contact areas and lower contact pressure were found in the control size. Post-cam engagement angles were similar on both sizes. Changes in TKA size slightly affected knee kinematics and kinetics, with post-cam related differences leading to minor changes in kinetic patterns.

Development and validation of an in-silico virtual testing rig for analyzing total knee arthroplasty performance during passive deep flexion: A feasibility study

The use of in-silico finite element (FE) models has become more common in orthopedic applications and in the design of biomedical devices, since they can provide results comparable to in vitro experiments while maintaining lower cost. The main downside of this kind of analysis is the high computing time, as it can reach hours or even days to complete; this limitation makes it then not suitable for time-sensitive applications, such as probabilistic analyses or helping clinicians in surgical pre-planning or intra-operative setting. In-silico multibody (MB) simulations, on the other hand, are significantly faster than FE simulations (considering each component of the model as a rigid body); although deformability of each model component is a necessary feature in some applications (e.g. simulation of implant-bone micromotions), several outputs of interest in orthopedic applications, such as implant kinematics and contact forces, do not require a fully deformable model. Therefore, this feasibility study aimed to develop a MB model of a human knee joint implanted with a Total Knee Arthroplasty; a 10 second flexion movement up to 105° was then simulated and the results compared with validated FE models results (under similar boundary conditions) from literature, to perform a preliminary validation in terms of kinematic and kinetic results between the two methods. The agreement and relatively low computing time obtaining with this approach represent a promising starting point for subsequent studies and applications of such techniques in the clinical field.

Length of anterior cruciate ligament affects knee kinematics and kinetics using a musculoskeletal computer simulation model

Introduction

The tension of anterior cruciate ligament (ACL) graft has an important role in antero-posterior (AP) and rotational stability of the knee. The purposes of this study were to analyze the kinematics and kinetics of normal knee models with loose and tight ACL tension, and to evaluate the effect of the tension of ACL on knee kinematics and kinetics.

Materials and methods

Slack and tight ACL models were constructed in a musculoskeletal computer simulation. The effect of ACL tension on kinematics, and femorotibial contact force during various activities was analyzed.

Results

During stair descent activity in the slack ACL models, the lateral femoral condyles were positioned posterior, and more external rotation of the femur was observed in comparison with the normal model. The contact forces at the lateral compartment in the tight models increased during all activities, and the tension of the medial collateral ligament (MCL) in the slack models increased during the stair descent activity, compared with the normal knee model.

Conclusion

AP and rotational instability and excessive MCL tension were observed in the ACL slack knees especially during stair descent movement, whereas the tibiofemoral contact force of the lateral compartment increased in the tight ACL knees.

High congruency MB insert design: stabilizing knee joint even with PCL deficiency

PURPOSE

PCL management and choice of insert design and mobility in total knee arthroplasty are still debated in the literature. Consequently, the purpose of this study was to analyze the biomechanics of a fixed and a mobile bearing total knee arthroplasty with conventional and ultra-congruent insert during walking and squat activities, using finite element analysis, and to check the performance in a knee with healthy and deficient PCL.

METHODS

The study was based on an already validated and published knee model. Fixed bearing and mobile bearing cruciate-retain designs were selected for this study. Implant kinematics and kinetics were calculated, following previously experimental tests, during a walking cycle and a loaded squat in a knee with intact and with deficient PCL.

RESULTS

Mobile bearing design, due to its higher congruency, was able to complete the task in intact and deficient PCL conditions, with similar internal-external femoral rotation and with a slight higher anterior translation of the one of the intact knees. Such outcomes were also in agreement with the results of different experimental studies of native knee specimens under similar boundary conditions. Contrariwise, fixed bearing design was able to accomplish the task only in healthy PCL conditions.

CONCLUSION

Results demonstrated how the high congruency of the mobile bearing design is able to guarantee proper knee stability and kinematics even when the PCL is deficient. Instead, the fixed bearing insert, with lower congruency, is not able, in the absence of the PCL, to stabilize the joint inducing irregular kinematic pattern and component dislocation. Surgeons will have to consider these findings to guarantee the best outcome for the patient and the related change in stability in case of PCL deficiency.

Musculoskeletal Multibody Simulation Analysis on the Impact of Patellar Component Design and Positioning on Joint Dynamics after Unconstrained Total Knee Arthroplasty

Patellofemoral (PF) disorders are considered a major clinical complication after total knee replacement (TKR). Malpositioning and design of the patellar component impacts knee joint dynamics, implant fixation and wear propagation. However, only a limited number of studies have addressed the biomechanical impact of the patellar component on PF dynamics and their results have been discussed controversially. To address these issues, we implemented a musculoskeletal multibody simulation (MMBS) study for the systematical analysis of the patellar component’s thickness and positioning on PF contact forces and kinematics during dynamic squat motion with virtually implanted unconstrained cruciate-retaining (CR)-TKR. The patellar button thickness clearly increased the contact forces in the PF joint (up to 27%). Similarly, the PF contact forces were affected by superior–inferior positioning (up to 16%) and mediolateral positioning (up to 8%) of the patellar button. PF kinematics was mostly affected by the mediolateral positioning and the thickness of the patellar component. A medialization of 3 mm caused a lateral patellar shift by up to 2.7 mm and lateral patellar tilt by up to 1.6°. However, deviations in the rotational positioning of the patellar button had minor effects on PF dynamics. Aiming at an optimal intraoperative patellar component alignment, the orthopedic surgeon should pay close attention to the patellar component thickness in combination with its mediolateral and superior–inferior positioning on the retropatellar surface. Our generated MMBS model provides systematic and reproducible insight into the effects of patellar component positioning and design on PF dynamics and has the potential to serve as a preoperative analysis tool.

EVALUATING THE EFFECTS OF EXPERIMENTAL SETTINGS DURING ISO 7206-4 ENDURANCE AND PERFORMACE TESTS: A FINITE ELEMENT ANALYSIS

ISO 7206-4:2010 is used to determine the endurance properties and performance of stemmed femoral components of hip prosthesis. Experimental set-ups are allowed for tolerances with respect to the desired settings. The effects of the acceptable accuracies are not known nowadays. For this reason, this study aims at evaluating how and how much the precision of the experimental settings can affect the outputs under ISO 7206-4:2010 boundaries. Thus, a finite element model was first defined and verified against experimental test. Then, a sensitivity analysis involving accepted variations for potting level, angle in the frontal plane, angle in the lateral plane and material in use for the cement block, was performed. The results of sensitivity analysis show that both stress and deformation outputs were affected up to 100[Formula: see text]MPa and 0.5[Formula: see text]mm, respectively, for varus configurations. The material properties of the cement block had a main effect on the displacement of the head. The collected information through the performed sensitivity analysis on the verified model against experimental test has a double benefit. It supports the understanding of the potential effects during the experimental set-ups and it is also helpful in case of determining ranges for verification of developed numerical models.

Classical target coronal alignment in high tibial osteotomy demonstrates validity in terms of knee kinematics and kinetics in a computer model

PURPOSE

The purpose of this study was to determine the ideal coronal alignment under dynamic conditions after open-wedge high tibial osteotomy (OWHTO). It was hypothesised that, although the classical target alignment was based on experimental evidence, it would demonstrate biomechanical validity.

METHODS

Musculoskeletal computer models were analysed with various degrees of coronal correction in OWHTO during gait and squat, specifically with the mechanical axis passing through points at 40%, 50%, 60%, 62.5%, 70%, and 80% of the tibial plateau from the medial edge, defined as the weight-bearing line percentage (WBL%). The peak load on the lateral tibiofemoral (TF) joint, the medial collateral ligament (MCL), and anterior cruciate ligament (ACL) tensions, and knee kinematics with or without increased posterior tibial slope (PTS) were evaluated.

RESULTS

The classical alignment with WBL62.5% achieved sufficient load on the lateral TF joint and maintained normal knee kinematics after OWHTO. However, over-correction with WBL80% caused an excessive lateral load and non-physiological kinematics. Increased WBL% resulted in increased MCL tension due to lateral femoral movement against the tibia. With WBL80%, abnormal contact between the medial femoral condyle and the medial intercondylar eminence of the tibia occurred at knee extension. The screw-home movement around knee extension and the TF rotational angle during flexion were reduced as WBL% increased. Increased PTS was associated with increased ACL tension and decreased TF rotation angle because of ligamentous imbalance.

CONCLUSIONS

The classical target alignment demonstrated validity in OWHTO, and over-correction should be avoided as it negatively impacts clinical outcome.

LEVEL OF EVIDENCE

IV.

Analysis of Biomechanical Differences Between Condylar Constrained Knee and Rotating Hinged Implants: A Numerical Study

BACKGROUND

Different levels of constraint for total knee arthroplasty can be considered for revision surgeries. While prior studies have assessed the clinical impact and patient outcomes of condylar constrained knee (CCK) and rotating hinged (RTH) implants, nowadays little is known about the biomechanical effects induced by different levels of constraint on bone stress and implant micromotions.

METHODS

CCK and RTH implant models were analyzed using a previously validated numerical model. Each system was investigated during a squat and a lunge motor task. The force in the joint, the bone and implant stresses, and micromotions in this latter were analyzed and compared among designs.

RESULTS

Different activities induced similar bone stress distributions in both implants. The RTH implant induces mostly high stress compared to the CCK implant, especially in the region close to tip of the stem. However, in the proximal tibia, the stresses achieved with the CCK implant is higher than the one calculated for the RTH design, due to the presence of the post-cam system. Accordingly, the condylar constrained design shows higher implant micromotions due to the greater torsional constraint.

CONCLUSION

Different levels of constraint in revision arthroplasty were always associated with different biomechanical outputs. RTH implants are characterized by higher tibial stress especially in the region close to the stem tip; condylar implants, instead, increase the proximal tibial stress and therefore implant micromotions, as a result of the presence of the post-cam mechanism. Surgeons will have to consider these findings to guarantee the best outcome for the patient and the related change in the bone stress and implant fixation induced by different levels of constrain in a total knee arthroplasty.

Impact of tibial baseplate malposition on kinematics, contact forces and ligament tensions in TKA: A numerical analysis

PURPOSE

Malposition of implant components in total knee arthroplasty (TKA) has consequences on tibiofemoral kinematics, contact forces and ligament tensions. To evaluate the impact of tibial baseplate malpositioning in the same knee, we conducted a computer simulation.

METHODS

An established weight-bearing finite element model of a fixed bearing TKA was used for the computer simulation. To evaluate the influence of tibial baseplate malposition, calculations were consecutively performed in neutral position, at 3° and 6° of internal and external rotation and at 3 mm and 6 mm of medial and lateral translation.

RESULTS

The highest effect of malposition was observed for ligament tensions, with a tendency of a greater influence for the 6 mm translation compared to 6° of rotation. Changes in contact forces and tibiofemoral kinematics were according to the alterations of ligament tensions. The highest ligament tension, contact force and femoral roll-back were registered for 6 mm medialization of the tibial baseplate.

DISCUSSION

Tibial baseplate malposition effects ligament tensions, tibiofemoral contact forces and kinematics and has a risk of unfavorable clinical results due to postoperative pain, reduced range of motion, instability and a higher rate of early loosening. Therefore, surgeons should aim for a neutral position of the tibial baseplate.

Neuro-musculoskeletal flexible multibody simulation yields a framework for efficient bone failure risk assessment

Fragility fractures are a major socioeconomic problem. A non-invasive, computationally-efficient method for the identification of fracture risk scenarios under the representation of neuro-musculoskeletal dynamics does not exist. We introduce a computational workflow that integrates modally-reduced, quantitative CT-based finite-element models into neuro-musculoskeletal flexible multibody simulation (NfMBS) for early bone fracture risk assessment. Our workflow quantifies the bone strength via the osteogenic stresses and strains that arise due to the physiological-like loading of the bone under the representation of patient-specific neuro-musculoskeletal dynamics. This allows for non-invasive, computationally-efficient dynamic analysis over the enormous parameter space of fracture risk scenarios, while requiring only sparse clinical data. Experimental validation on a fresh human femur specimen together with femur strength computations that were consistent with literature findings provide confidence in the workflow: The simulation of an entire squat took only 38 s CPU-time. Owing to the loss (16% cortical, 33% trabecular) of bone mineral density (BMD), the strain measure that is associated with bone fracture increased by 31.4%; and yielded an elevated risk of a femoral hip fracture. Our novel workflow could offer clinicians with decision-making guidance by enabling the first combined in-silico analysis tool using NfMBS and BMD measurements for optimized bone fracture risk assessment.

Patellar bone strain after total knee arthroplasty is correlated with bone mineral density and body mass index

Patella-related complications after total knee arthroplasty (TKA) remain a major clinical concern. Previous studies have suggested that increased postoperative patellar bone strain could be related to such complications, but there is limited knowledge on patellar strain after TKA. The objective of this study was to predict patellar bone strain after TKA and evaluate correlations with various preoperative data. Fourteen TKA patients with a minimum follow-up of one year were included in this study. Using preoperative CT datasets, preoperative planning, and postoperative X-rays, a method is presented to generate patient-specific finite element models after virtual TKA. Patellar kinematics and forces were predicted during a squat movement, and patellar bone strain was evaluated at 60° of knee flexion. Strain varied greatly among patients, but was strongly negatively correlated (r = -0.85, p < 0.001) with bone mineral density (BMD) and moderately positively (r  = 0.54, p  =  0.05) with body mass index (BMI). The BMI/BMD ratio explained 87% of strain, and should be further investigated as a potential risk factor for clinical complications. This study represents a preliminary step towards the identification of patients at risk of patellar complications after TKA.

Effect of tibial component alignment on knee kinematics and ligament tension in medial unicompartmental knee arthroplasty

Objectives

Unicompartmental knee arthroplasty (UKA) is one surgical option for treating symptomatic medial osteoarthritis. Clinical studies have shown the functional benefits of UKA; however, the optimal alignment of the tibial component is still debated. The purpose of this study was to evaluate the effects of tibial coronal and sagittal plane alignment in UKA on knee kinematics and cruciate ligament tension, using a musculoskeletal computer simulation.

Methods

The tibial component was first aligned perpendicular to the mechanical axis of the tibia, with a 7° posterior slope (basic model). Subsequently, coronal and sagittal plane alignments were changed in a simulation programme. Kinematics and cruciate ligament tensions were simulated during weight-bearing deep knee bend and gait motions. Translation was defined as the distance between the most medial and the most lateral femoral positions throughout the cycle.

Results

The femur was positioned more medially relative to the tibia, with increasing varus alignment of the tibial component. Medial/lateral (ML) translation was smallest in the 2° varus model. A greater posterior slope posteriorized the medial condyle and increased anterior cruciate ligament (ACL) tension. ML translation was increased in the > 7° posterior slope model and the 0° model.

Conclusion

The current study suggests that the preferred tibial component alignment is between neutral and 2° varus in the coronal plane, and between 3° and 7° posterior slope in the sagittal plane. Varus > 4° or valgus alignment and excessive posterior slope caused excessive ML translation, which could be related to feelings of instability and could potentially have negative effects on clinical outcomes and implant durability.

Cite this article: K. Sekiguchi, S. Nakamura, S. Kuriyama, K. Nishitani, H. Ito, Y. Tanaka, M. Watanabe, S. Matsuda. Bone Joint Res 2019;8:126–135. DOI: 10.1302/2046-3758.83.BJR-2018-0208.R2.

Asymmetric polyethylene inserts promote favorable kinematics and better clinical outcome compared to symmetric inserts in a mobile bearing total knee arthroplasty

PURPOSE

This study aims at comparing the effects of symmetric and asymmetric designs for the polyethylene insert currently available and also for mobile bearing total knee arthroplasty (TKA). The investigation was performed both clinically and biomechanically through finite element analysis.

METHODS

303 patients, with a mobile bearing TKA, were analyzed retrospectively. All patients received the same femoral and tibial components; for the insert, 151 patients received a symmetric design (SD) and 152 an asymmetric design (AD). Additionally, a 3D finite element model of a lower leg was developed, resurfaced with the same TKAs and analysed during gait and squat activities. TKA kinematics, and bone-stresses were investigated for the two insert solutions.

RESULTS

After surgery, patients' average flexion improved from 105°, with 5° of preoperative extension deficit, to 120° (AD-group) and 115° (SD-group) at the latest follow-up. There was no postoperative extension deficit. No pain affected the AD-group, while an antero-lateral pain was reported in some patients of the SD-group. Patients of the AD-group presented a better ability to perform certain physical routines. Biomechanically, the SD induced higher tibial-bone stresses than the AD. Both designs replicated similar kinematics, comparable to literature. However, SD rotates more on the tray, reducing the motion between femoral and polyethylene components, while AD permits greater insert rotation.

CONCLUSION

The biomechanical analysis justifies the clinical findings. TKA kinematics is similar for the two designs, although the asymmetric solution shows less bone stress, thus resulting as more suitable to be cemented, avoiding lift-off issues, inducing less pain. Clinically, and biomechanically, an asymmetric mobile bearing insert could be a valid alternative to symmetric mobile bearing insert.

LEVEL OF EVIDENCE

Case-control study retrospective comparative study, III.

Impact of intraoperative adjustment method for increased flexion gap on knee kinematics after posterior cruciate ligament-sacrificing total knee arthroplasty

BACKGROUND

In general, the flexion gap is larger than the extension gap with posterior cruciate ligament-sacrificing total knee arthroplasty. Several methods compensate for an excessive flexion gap, but their effects are unknown. The purpose of this study was to compare three methods to compensate for an increased flexion gap.

METHODS

In this study, squatting in knees with excessive (4 mm) and moderate (2 mm) flexion gaps was simulated in a computer model. Differences in knee kinematics and kinetics with joint line elevation, setting the femoral component in flexion, and using a larger femoral component as compensatory methods were investigated.

FINDINGS

The rotational kinematics during flexion with setting the femoral component in flexion were opposite to those in the other models. Using a larger femoral component resulted in the most physiological motion. The peak anterior translation was 10 mm in the joint line elevation model compared with approximately 6 mm in the other models. In the joint line elevation model, patellofemoral contact stress was excessively increased at 90° of knee flexion. In contrast, tibiofemoral contact stress was higher during knee extension with setting the femoral component in flexion due to anterior impingement. There were few differences in the effect of the three compensatory methods with a moderate flexion gap.

INTERPRETATION

A larger femoral component should be used to compensate for an excessive flexion gap because it has less negative impact on posterior cruciate ligament-sacrificing total knee arthroplasty, whereas any compensation method might be acceptable for a moderate flexion gap.

Biomechanical Analysis of Augments in Revision Total Knee Arthroplasty

Augments are a common solution for treating bone loss in revision total knee arthroplasty and industry is providing to surgeons several options, in terms of material, thickness and shapes. Actually, while the choice of the shape and the thickness is mainly dictated by the bone defect, no proper guidelines are currently available to select the optimal material for a specific clinical situation. Nevertheless, different materials could induce different bone responses and, later, potentially compromise implant stability and performances. Therefore, in this study, a biomechanical analysis is performed by means of finite element modelling about existing features for augment designs. Based upon a review of available products at present, the following augments features were analyzed: position (distal/proximal and posterior), thickness (5, 10 and 15 mm) and material (bone cement, porous and solid metal). For all analyzed configurations, bone stresses were investigated in different regions and compared among all configurations and the control model for which no augments were used. Results show that the use of any kind of augment usually induces a change in bone stresses, especially in the region close to the bone cut. The porous metal presents result very close to cement ones; thus it could be considered as a good alternative for defects of any size. Solid metal has the least satisfying results inducing the highest changes in bone stress. The results of this study demonstrate that material stiffness of the augment should be as close as possible to bone properties for allowing the best implant performances.

Comparison of Kinematics in Cruciate Retaining and Posterior Stabilized for Fixed and Rotating Platform Mobile-Bearing Total Knee Arthroplasty with respect to Different Posterior Tibial Slope

Reconstructed posterior tibial slope (PTS) plays a significant role in kinematics restoration after total knee arthroplasty (TKA). However, the effect of increased and decreased PTS on prosthetic type and design has not yet been investigated. We used a finite element model, validated using in vitro data, to evaluate the effect of PTS on knee kinematics in cruciate-retaining (CR) and posterior-stabilized (PS) fixed TKA and rotating platform mobile-bearing TKA. Anterior-posterior tibial translation and internal-external tibial rotation were investigated for PTS ranging from -3° to 15°, with increments of 1°, for three different designs of TKA. Tibial posterior translation and external rotation increased as the PTS increased in both CR and PS TKAs. In addition, there was no remarkable difference in external rotation between CR and PS TKAs. However, for the mobile-bearing TKA, PTS had less effect on the kinematics. Based on our computational simulation, PTS is the critical factor that influences kinematics in TKA, especially in the CR TKA. Therefore, the surgeon should be careful in choosing the PTS in CR TKAs.

Sensitivity analysis of the material properties of different soft-tissues: implications for a subject-specific knee arthroplasty

Introduction

While developing a subject-specific knee model, different kinds of data-inputs are required. If information about geometries can be definitely obtained from images, more effort is necessary for the in vivo properties. Consequently, such information are recruited from the literature as common habit. However, the effects of the combined sources still need to be evaluated.

Methods

This work aims at developing an intact native subject-specific knee model for performing a sensitivity analysis on soft-tissues. The impacts on the biomechanical outputs were analysed during a daily activity for which articular knee kinetics and kinematics were compared among the different configurations. Prior to the sensitivity analysis, experimental and literature data were checked for the model reliability.

Results

Average values of mixed sources allowed the agreement with experimental data for personalized outputs. From the sensitivity analysis, knee kinematics did not significantly change in the selected ranges of properties for the soft-tissues (in rotation less than 0.5°), while contact stresses were greatly affected, especially for the articular cartilage (with differences in the results more than 100%).

Conclusion

In conclusion, during the development of a personalized knee model, the selection of the correct material properties is fundamental because wrong values could highly affect the numerical results.

Level of evidence

III a.

Assessment of patient functional performance in different knee arthroplasty designs during unconstrained squat

Background

In this paper, squat named by Authors unconstrained because performed without constrains related to feet position, speed, knee maximum angle to be reached, was tested as motor task revealing differences in functional performance after knee arthroplasty. It involves large joints ranges of motion, does not compromise joint safety and requires accurate control strategies to maintain balance.

Methods

Motion capture techniques were used to study squat on a healthy control group (CTR) and on three groups, each characterised by a specific knee arthroplasty design: a Total Knee Arthroplasty (TKA), a Mobile Bearing and a Fixed Bearing Unicompartmental Knee Arthroplasty (respectively MBUA and FBUA). Squat was analysed during descent, maintenance and ascent phase and described by speed, angular kinematics of lower and upper body, the Center of Pressure (CoP) trajectory and muscle activation timing of quadriceps and biceps femoris.

Results

Compared to CTR, for TKA and MBUA knee maximum flexion was lower, vertical speed during descent and ascent reduced and the duration of whole movement was longer. CoP mean distance was higher for all arthroplasty groups during descent as higher was, CoP mean velocity for MBUA and TKA during ascent and descent.

Conclusions

Unconstrained squat is able to reveal differences in the functional performance among control and arthroplasty groups and between different arthroplasty designs. Considering the similarity index calculated for the variables showing statistically significance, FBUA performance appears to be closest to that of the CTR group.

Level of evidence

III a.

Varus femoral and tibial coronal alignments result in different kinematics and kinetics after total knee arthroplasty

PURPOSE

Abnormal knee motion under various conditions has been described after total knee arthroplasty (TKA). However, differences in kinematics and kinetics of knees with varus femoral versus varus tibial alignment have not been evaluated. It was hypothesized that varus femoral and tibial alignments have the same impact on knee motion.

METHODS

A musculoskeletal computer simulation was used. Femoral and tibial alignment in the coronal plane was each varied from neutral to 5° of varus in 1° increments. Lift-off, defined as an intercomponent distance of >2 mm, and tibiofemoral contact forces were evaluated during gait up to 60° of knee flexion. Knee kinematics and contact stresses were also examined during squat, with up to 130° of knee flexion.

RESULTS

During gait, lift-off occurred readily with more than 3° of varus tibial alignment and slight lateral joint laxity. In contrast, lift-off did not occur with varus femoral or tibial alignment of up to 5° during squat. Peak medial contact forces with varus femoral alignment were approximately twice those observed with varus tibial alignment. The lowest points of the femoral condyles moved internally with varus femoral alignment, contrary to the kinematics with neutral or varus tibial alignment. On the other hand, there was femoral medial sliding and edge loading against the tibia in mid-flexion with varus tibial alignment.

CONCLUSION

Varus femoral alignment affects the non-physiological rotational movement of the tibiofemoral joint, whereas varus tibial alignment causes medial-lateral instability during mid-flexion. Varus femoral and tibial alignments might lead to post-TKA discomfort and unreliability.

In vivo kinematics of knee replacement during daily living activities: Condylar and post-cam contact assessment by three-dimensional fluoroscopy and finite element analyses

In total knee replacement, the investigation on the exact contact patterns at the post-cam in implanted patients from real in vivo data during daily living activities is fundamental for validating implant design concepts and assessing relevant performances. This study is aimed at verifying the restoration of natural tibio-femoral condylar kinematics by investigating the post-cam engagement at different motor tasks. An innovative validated technique, combining three-dimensional fluoroscopic and finite element analyses, was applied to measure joint kinematics during daily living activities in 15 patients implanted with guided motion posterior-stabilized total knee replacement. Motion results showed physiological antero-posterior translations of the tibio-femoral condyles for every motor task. However, high variability was observed in the position of the calculated pivot point among different patients and different motor tasks, as well as in the range of post-cam engagement. Physiological tibio-femoral joint rotations and contacts at the condyles were found restored in the present knee replacement. Articular contact patterns experienced at the post-cam were found compatible with this original prosthesis design. The present study reports replaced knee kinematics also in terms of articular surface contacts, both at the condyles and, for the first time, at the post-cam. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:1396-1403, 2017.

Superior-inferior position of patellar component affects patellofemoral kinematics and contact forces in computer simulation

BACKGROUND

Anterior knee pain has been reported as a major postoperative complication after total knee arthroplasty, which may lead to patient dissatisfaction. Rotational alignment and the medial-lateral position correlate with patellar maltracking, which can cause knee pain postoperatively. However, the superior-inferior position of the patellar component has not been investigated. The purpose of the current study was to investigate the effects of the patellar superior-inferior position on patellofemoral kinematics and kinetics.

METHODS

Superior, central, and inferior models with a dome patellar component were constructed. In the superior and inferior models, the position of the patellar component translated superiorly and inferiorly, respectively, by 3mm, relative to the center model. Kinematics of the patellar component, quadriceps force, and patellofemoral contact force were calculated using a computer simulation during a squatting activity in a weight-bearing deep knee bend.

FINDINGS

In the inferior model, the flexion angle, relative to the tibial component, was the greatest among all models. The inferior model showed an 18.0%, 36.5%, and 22.7% increase in the maximum quadriceps force, the maximum medial patellofemoral force, and the maximum lateral patellofemoral force, respectively, compared with the superior model.

INTERPRETATION

Superior-inferior positions affected patellofemoral kinematic and kinetics. Surgeons should avoid the inferior position of the patellar component, because the inferior positioned model showed greater quadriceps and patellofemoral force, resulting in a potential risk for anterior knee pain and component loosening.

Biomechanical Effects of Different Varus and Valgus Alignments in Medial Unicompartmental Knee Arthroplasty

BACKGROUND

Medial unicompartmental tibial components are not always positioned following neutral mechanical alignment and a tibial varus alignment of 3° has been suggested based on several clinical follow-up studies. However, no biomechanical justification is currently available to confirm the suitability of different alignment positions.

METHODS

This study aims at quantifying the effects on bone stresses, load distribution, ligament strains, and polyethylene insert stress distribution induced by a possible varus/valgus alignment in medial unicompartmental knee arthroplasty, ranging from 6° of varus to 6° of valgus, developing and using a validated patient-specific finite element model.

RESULTS

Results demonstrate that both neutral mechanical and 3° of varus alignment induce lower stress distributions than valgus or a higher varus alignment for which higher values, up to 40%, are achieved for the polyethylene stress. When a unicompartmental knee arthroplasty is implanted, a mismatch in the stiffness of the joint is introduced, changing the load distribution from medial to lateral for all configurations with respect to the native configuration. However, slight differences are noticeable among the different configurations with a maximum of 190 N and 90 N for the lateral and the medial side, respectively.

CONCLUSION

Neutral mechanical or 3° of varus alignment present similar biomechanical outputs in the bone, collateral ligament strain, and on the polyethylene insert. A 6° varus alignment or changes in valgus alignment were always associated with more detrimental effects.

Fixation techniques and stem dimensions in hinged total knee arthroplasty: a finite element study

INTRODUCTION

No evidence-based guidelines are available to determine the appropriate stem length, and whether or not to cement stems in revision total knee arthroplasty (TKA). Therefore, the objective of this study was to compare stresses and relative movement of cemented and uncemented stems of different lengths using a finite element analysis.

MATERIALS AND METHODS

A finite element model was created for a synthetic tibia. Two stem lengths (95 and 160 mm) and two types of fixation (cemented or press fit) of a hinged TKA were examined. The average compressive stress distribution in different regions of interest, as well as implant micromotions, was determined and compared during lunge and squat motor tasks.

RESULTS

Both long and short stems in revision TKA lead to high stresses, primarily in the region around the stem tip. The presence of cement reduces the stresses in the bone in every region along the stem. Short stem configurations are less affected by the presence of cement than the long stem configuration. Press-fit stems showed higher micromotions compared to cemented stems.

CONCLUSIONS

Lowest stresses and micromotion were found for long cemented stems. Cementless stems showed more micromotion and increased stress levels especially at the level of the stem tip, which may explain the clinical phenomenon of stem-end pain following revision knee arthroplasty. These findings will help the surgeon with optimal individual implant choice.

ARE MRIs NECESSARY TO DEVELOP SUBJECT-SPECIFIC CARTILAGE AND MENISCI GEOMETRIES FOR SUBJECT-SPECIFIC KNEE MODELS?

Native subject-specific knee geometries are usually based on CT and MRI images reconstruction. Unfortunately, while the definition of bone geometries using CTs is quite consistent, MRIs are often hardly readable, due to the usual lower resolution, and the final shape of cartilage and menisci is not consequently detailed enough. Moreover, further smoothing techniques, necessary to efficiently use these structures for numerical modeling, could result in bad interfaces and/or geometry inaccuracies. In this study a CAD-based approach to generate 3D cartilages and menisci geometries, avoiding the use of MRIs, was proposed and tested versus the traditional methods that use MRIs segmentation. The femoral, tibial and patellar cartilage layers were generated as offset from the bone geometries, the menisci were obtained by an extrusion based on tibia borders. Such geometries were compared to the reconstructions obtained from MRIs of healthy knee specimens. Overlapping the resulting geometries with the ones traditionally reconstructed, volumes differ from 2% to 14%. By using the new methodology, the geometries are obtained in 75% less time. The CAD-based methods shown in this pilot study is able to generate faster and accurate subject-specific knee cartilage layers and menisci geometries and can be suitable to be applied for numerical modeling.

Knee kinetics and kinematics: What are the effects of TKA malconfigurations?

PURPOSE

Total knee arthroplasty (TKA) is a very successful surgical procedure. However, implant failures and patient dissatisfaction still persist. Sometimes surgeons are not able to understand and explain these negative performances because the patient's medical images "look good", but the patient "feels bad". Apart from radiograph imaging and clinical outcome scores, conventionally used follow-up methods are mainly based on the analysis of knee kinematics. However, even if kinematics remains close to the "normal" range of motion, the patient may still complain about pain and functional limitations. To provide more insight into this paradox, a better quantitative understanding of TKA mechanics must be developed. For this purpose, improved techniques for clinical follow-up, combining kinetics and kinematics analysis, should be introduced to help surgeons to assess and understand TKA performance.

METHODS

An analysis on four TKA designs was performed, and the changes in kinematics and in kinetics induced by several implant configurations (simulating implant malalignment and different knee anatomy) were compared. More specifically, analysed tibio-femoral and patello-femoral contact forces and tibio-femoral kinematics were analysed during a squat task up to 120°.

RESULTS

The results from this study show that contact forces (with changes up to 67 %) are more heavily affected by malconfigurations than kinematics, for which maximum deviations are of the order of 5 mm or 5°, similar to the simulated surgical errors. The results present a similar trend for the different designs.

CONCLUSIONS

The results confirm the hypothesis that kinematics is not the only and also not the most relevant parameter to predict or explain knee function after TKA. In the future, techniques to analyse knee kinetics should be integrated in the clinical follow-up.

How accurate and reproducible are the identification of cruciate and collateral ligament insertions using MRI?

BACKGROUND

At present, increasing the accuracy of identification of knee ligament insertions is fundamental in developing accurate patient-specific three-dimensional (3D) models for preoperative planning surgeries, designing patient-specific instrumentation or implants, and conducting biomechanical analyses. The accuracy and reproducibility of magnetic resonance imaging (MRI) scans in identifying cruciate and collateral ligament insertions have not been investigated thus far, despite their wide use. This study aimed to define and validate a method for this purpose.

METHODS

First, the femur and tibia bones were oriented. Then, the sites of cruciate and collateral ligament insertions were identified. The inter- and intra-class correlation coefficients (ICCs) were calculated after multiple operators were applied to the images of different patients. The effect of the quality of the available MRI scans on the accuracy of identifying ligament insertions was also investigated. Moreover, non-expert operators were also found to be capable of performing the procedure after a video tutorial, and its efficacy was tested.

RESULTS

The mean intra-observer variability was always <1.5mm for all landmarks, whereas the mean inter-observer variability was always <2.5mm except for the medial collateral ligament localized on the tibia (6.7mm). The ICCs showed good results, up to 0.99. A lower image quality had no noticeable effect on the procedure for identifying cruciate ligaments. Video tutorials were found to improve the ICCs up to 45%.

CONCLUSIONS

This procedure is suitable for the univocal and accurate identification of cruciate and lateral collateral ligaments on MRI scans.

CLINICAL RELEVANCE

This study demonstrates that MRI scans are highly suited to identifying cruciate ligament insertions.

All-polyethylene tibial components generate higher stress and micromotions than metal-backed tibial components in total knee arthroplasty

PURPOSE

Most total knee arthroplasty tibial components are metal-backed, but an alternative tibial component made entirely of polyethylene (all-polyethylene design) exists. While several clinical studies have shown that all-poly design performs similarly to the metal-backed, the objective of this study is to perform a biomechanical comparison.

METHODS

Loads, constraints and geometries during a squat activity at 120° of flexion were obtained from a validated musculoskeletal model and applied to a finite element model. Stresses in the tibia and micromotions at the bone-implant interface were evaluated for several implant configurations: (1) three different thicknesses of the cement penetration under the baseplate (2, 3 and 4 mm), (2) the presence or absence of a cement layer around the stem of the tibial tray and (3) three different bone conditions (physiological, osteopenic and osteoporotic bone).

RESULTS

All-polyethylene tibial components resulted in significantly higher (p < 0.001) and more uneven stress distributions in the cancellous bone under the baseplate (peak difference: +128.4 %) and fivefold increased micromotions (p < 0.001). Performance of both implant designs worsened with poorer bone quality with peaks in stress and micromotion variations of +40.8 and +54.0 %, respectively (p < 0.001). Performance improvements when the stem was cemented were not statistically significant (n.s.).

CONCLUSION

The metal-backed design showed better biomechanical performance during a squat activity at 120° of flexion compared to the all-polyethylene design. These results should be considered when selecting the appropriate tibial component for a patient, especially in the presence of osteoporotic bone or if intense physical activity is foreseen.

A new graphical method to display data sets representing biomechanical knee behaviour

Background

When researchers describe data from their studies, there is no rule defining the best way to represent results. Therefore, collecting and explaining results from personal research or understanding data from publications is not always straightforward. These issues are even worse in fields such as biomedical engineering, where researchers from different backgrounds, usually engineers and surgeons, need to interact and exchange information. For these reasons, the purpose of this study is to introduce and illustrate an innovative method to represent, concisely and intuitively, biomechanical knee behavior, called KneePrints.

Methods

To test the KneePrints method, a huge amount of data from previously published sensitivity analyses were used and represented both with conventional techniques and with this new graphical method. Then, a survey has been distributed among different international specialists in the orthopedic field, such as surgeons and researchers. In the survey, interviewees were asked to select the favorite method that addressed to be the most effective to show the same results.

Results

Collecting the outcomes from the survey, the KneePrints method resulted to be more effective than standard graphs, such as tables and histograms. KneePrints method has been selected to be clearer in representing outputs and more immediate in results understanding independently from the occupation of the interviewees by the survey. The general preference for the KneePrints is 63 %, up to 74 % being surgeons’ choice.

Conclusions

The innovative KneePrints method has been endorsed to be effective in representing and making more understandable knee joint outputs. This method can be extended also to other topics.

Deviations From Optimal Alignment in TKA: Is There a Biomechanical Difference Between Femoral or Tibial Component Alignment?

Restoration of neutral mechanical alignment is one of the prerequisites for long-term TKA survival. This study aimed to investigate the effect of deviations from neutral alignment on bone and implant stress and on ligament strain. Using a previously validated finite element model, a neutrally aligned TKA model was compared to 3 different varus and valgus configurations induced by tibial or by femoral component only and by both component simultaneously. Each model underwent a 2500 N vertical load simulating the peak walking force. Varus and valgus alignment increased polyethylene and bone stress, and altered ligament strains, as compared to the neutral aligned model. Changes in alignment of the tibial component were always associated with more detrimental effects compared to the one of the femoral component.

Effect of component mal-rotation on knee loading in total knee arthroplasty using multi-body dynamics modeling under a simulated walking gait

Mal-rotation of the components in total knee arthorplasty (TKA) is a major cause of postoperative complications, with an increased propensity for implant loosening or wear leading to revision. A musculoskeletal multi-body dynamics model was used to perform a parametric study of the effects of the rotational mal-alignments in TKA on the knee loading under a simulated walking gait. The knee contact forces were found to be more sensitive to variations in the varus-valgus rotation of both the tibial and the femoral components and the internal-external rotation of the femoral component in TKA. The varus-valgus mal-rotation of the tibial or femoral component and the internal-external mal-rotation of the femoral component with a 5° variation were found to affect the peak medial contact force by 17.8-53.1%, the peak lateral contact force by 35.0-88.4% and the peak total contact force by 5.2-18.7%. Our findings support the clinical observations that a greater than 3° internal mal-rotation of the femoral component may lead to unsatisfactory pain levels and a greater than 3° varus mal-rotation of the tibial component may lead to medial bone collapse. These findings determined the quantitative effects of the mal-rotation of the components in TKA on the contact load. The effect of such mal-rotation of the components of TKA on the kinematics would be further addressed in future studies.

Posterior tibial slope and femoral sizing affect posterior cruciate ligament tension in posterior cruciate-retaining total knee arthroplasty

BACKGROUND

During cruciate-retaining total knee arthroplasty, surgeons sometimes encounter increased tension of the posterior cruciate ligament. This study investigated the effects of femoral size, posterior tibial slope, and rotational alignment of the femoral and tibial components on forces at the posterior cruciate ligament in cruciate-retaining total knee arthroplasty using a musculoskeletal computer simulation.

METHODS

Forces at the posterior cruciate ligament were assessed with the standard femoral component, as well as with 2-mm upsizing and 2-mm downsizing in the anterior-posterior dimension. These forces were also determined with posterior tibial slope angles of 5°, 7°, and 9°, and lastly, were measured in 5° increments when the femoral (tibial) components were positioned from 5° (15°) of internal rotation to 5° (15°) of external rotation.

FINDINGS

Forces at the posterior cruciate ligament increased by up to 718N with the standard procedure during squatting. The 2-mm downsizing of the femoral component decreased the force at the posterior cruciate ligament by up to 47%. The 2° increment in posterior tibial slope decreased the force at the posterior cruciate ligament by up to 41%. In addition, posterior cruciate ligament tension increased by 11% during internal rotation of the femoral component, and increased by 18% during external rotation of the tibial component.

INTERPRETATION

These findings suggest that accurate sizing and bone preparation are very important to maintain posterior cruciate ligament forces in cruciate-retaining total knee arthroplasty. Care should also be taken regarding malrotation of the femoral and tibial components because this increases posterior cruciate ligament tension.

Kinematic alignment produces near-normal knee motion but increases contact stress after total knee arthroplasty: A case study on a single implant design

BACKGROUND

Kinematically aligned total knee arthroplasty (TKA) is of increasing interest because this method might improve postoperative patient satisfaction. In kinematic alignment the femoral component is implanted in a slightly more valgus and internally rotated position, and the tibial component is implanted in a slightly more varus and internally rotated position, than in mechanical alignment. However, the biomechanics of kinematically aligned TKA remain largely unknown. The aim of this study was to compare the kinematics and contact stresses of mechanically and kinematically aligned TKAs.

METHODS

A musculoskeletal computer simulation was used to determine the effects of mechanically or kinematically aligned TKA. Knee kinematics were examined for mechanically aligned, kinematically aligned, and kinematically aligned outlier models. Patellofemoral and tibiofemoral contact forces were measured using finite element analysis.

RESULTS

Greater femoral rollback and more external rotation of the femoral component were observed with kinematically aligned TKA than mechanically aligned TKA. However, patellofemoral and tibiofemoral contact stresses were increased in kinematically aligned TKA.

CONCLUSIONS

These findings suggest that kinematically aligned TKA produces near-normal knee kinematics, but that concerns for long-term outcome might arise because of high contact stresses.