Influence of graphene oxide and biochar on anaerobic degradation of petroleum hydrocarbons

Biochar enhanced the stability of toluene removal in extracted groundwater amended with nitrate under microaerobic conditions

Groundwater pollution caused by the leakage of petroleum and various fuel oils is becoming a serious environmental problem. In this study, carbon-based materials including biochar and hydrochar were applied to investigate the effects of additives on the toluene removal in the extracted groundwater under microaerobic condition with the addition of nitrate. Biochar and hydrochar could adsorb toluene, and thus enhance the toluene removal in the system. The toluene removal efficiency was 8.2-8.9 mg/(g·h) at the beginning, and then decreased with time in the control and the hydrochar treatment, while it remained the stable values in the biochar treatment, owing to the fact that biochar could reduce the NO3--N loss by partial denitrification. Moreover, biochar could prompt the growth of toluene-degrading bacteria including Thauera, Rhodococcus, Ideonella and Denitratisoma, which had the capability of denitrification. However, hydrochar could stimulated the growth of denitrifiers without toluene-degrading capacity including Candidatus Competibacter and Ferrovibrio, which might play a key role in the partial denitrification of the system. The findings are helpful for developing remediation techniques of contaminated groundwater.

Assessment of co-contaminated soil amended by graphene oxide: Effects on pollutants, microbial communities and soil health

Graphene oxide (GOx) is a nanomaterial with demonstrated capacity to remove metals from water. However, its effects on organic pollutants and metal(loid)s present in polluted soils when used for remediation purposes have not been extensively addressed. Likewise, few studies describe the effects of GOx on edaphic properties and soil biology. In this context, here we assessed the potential of GOx for remediating polluted soil focusing also on different unexplored effects of GOx in soil. To achieve this, we treated soil contaminated with concurrent inorganic (As and metals) and organic pollution (TPH and PAHs), using GOx alone and in combination with nutrients (N and P sources). In both cases increased availability of As and Zn was observed after 90 days, whereas Cu and Hg availability was reduced and the availability of Pb and the concentration of organic pollutants were not significantly affected. The application of GOx on the soil induced a significant and rapid change (within 1 week) in microbial populations, leading to a transient reduction in biodiversity, consistent with the alteration of several soil properties. Concurrently, the combination with nutrients exhibited a distinct behaviour, manifesting a more pronounced and persistent shift in microbial populations without a decrease in biodiversity. On the basis of these findings, GOx emerges as a versatile amendment for soil remediation approaches.

Environmental biotechnology and the involving biological process using graphene-based biocompatible material

Biotechnology is a promising approach to environmental remediation but requires improvement in efficiency and convenience. The improvement of biotechnology has been illustrated with the help of biocompatible materials as biocarrier for environmental remediations. Recently, graphene-based materials (GBMs) have become promising materials in environmental biotechnology. To better illustrate the principle and mechanisms of GBM application in biotechnology, the comprehension of the biological response of microorganisms and enzymes when facing the GBMs is needed. The review illustrated distinct GBM-microbe/enzyme composites by providing the GBM-microbe/enzyme interaction and the determining factors. There are diverse GBM modifications for distinct biotechnology applications. Each of these methods and applications depends on the physicochemical properties of GBMs. The applications of these composites were mainly categorized as pollutant adsorption, anaerobic digestion, microbial fuel cells, and organics degradation. Where information was available, the strategies and mechanisms of GBMs in improving application efficacies were also demonstrated. In addition, the biological response, from microbial community changes, extracellular polymeric substances changes to biological pathway alteration, may become important in the application of these composites. Furthermore, we also discuss challenges facing the environmental application of GBMs, considering their fate and toxicity in the ecosystem, and offer potential solutions. This research significantly enhances our comprehension of the fundamental principles, underlying mechanisms, and biological pathways for the in-situ utilization of GBMs.

Nano-bioremediation: an eco-friendly and effective step towards petroleum hydrocarbon removal from environment

Global concern about petroleum hydrocarbon pollution has intensified and gained scientific interest due to its noxious nature, high persistence in environmental matrices, and low degradability. One way to address this is by combining remediation techniques that could overcome the constraints of traditional physio-chemical and biological remediation strategies. The upgraded concept of bioremediation to nano-bioremediation in this direction offers an efficient, economical, and eco-friendly approach to mitigate petroleum contaminants. Here, we review the unique attributes of different types of nanoparticles and their synthesis procedures in remediating various petroleum pollutants. This review also highlights the microbial interaction with different metallic nanoparticles and their consequential alteration in microbial as well as enzymatic activity which expedites the remediating process. Besides, the latter part of the review explores the application of petroleum hydrocarbon degradation and the application of nano supports as immobilizing agents for microbes and enzymes. Further, the challenges and the future prospects of nano-bioremediation have also been discussed.

Construction and function of a high-efficient synthetic bacterial consortium to degrade aromatic VOCs

Aromatic volatile organic compounds (VOCs) are a type of common pollution form in chemical contaminated sites. In this study, seven aromatic VOCs such as benzene, toluene, ethylbenzene, chlorobenzene, m-xylene, p-chlorotoluene and p-chlorotrifluorotoluene were used as the only carbon source, and four strains of highly efficient degrading bacteria were screened from the soil of chemical contaminated sites, then the synthetic bacterial consortium was constructed after mixing with an existing functional strain (Bacillus benzoevorans) preserved in the laboratory. After that, the synthetic bacterial consortium was used to explore the degradation effect of simulated aromatic VOCs polluted wastewater. The results showed that the functional bacterium could metabolize with aromatic VOCs as the only carbon source and energy. Meanwhile, the growth of the synthetic bacterial consortium increased with the additional carbon resources and the alternative of organic nitrogen source. Ultimately, the applicability of the synthetic bacterial consortium in organic contaminated sites was explored through the study of broad-spectrum activity.

Comparison of the accelerating effect of graphene oxide and graphene on anaerobic transformation of bisphenol F by Pseudomonas sp. LS

It was found that bisphenol F (BPF) could be anaerobically transformed to 4,4-dihydroxybenzophenone using nitrate as an electron acceptor by Pseudomonas sp. LS. However, BPF removal was a slow process under anaerobic conditions. In the present study, effects of graphene oxide (GO) and graphene on the anaerobic transformation of BPF were studied in detail. Results showed that GO (2-10 mg/L) and graphene (2-20 mg/L) could increase the anaerobic biotransformation rate of BPF. For GO-mediated system, GO was partially reduced, and then the reduced GO (rGO) as an electron mediator increased biotransformation rate of BPF. Further analysis showed that the promoting effect of 10 mg/L GO was over 1.5-fold higher compared with that of 10 mg/L graphene. BPF could be transformed using GO as an electron acceptor. GO and graphene was also used as nutrient scaffolds to promote cell growth via adsorbing proteins. Moreover, GO was a better cell growth promoter than graphene. These studies indicated that GO played more roles and exhibited a better accelerating effect on anaerobic removal of BPF compared with graphene.

Progress and prospects of applying carbon-based materials (and nanomaterials) to accelerate anaerobic bioprocesses for the removal of micropollutants

Carbon-based materials (CBM), including activated carbon (AC), activated fibres (ACF), biochar (BC), nanotubes (CNT), carbon xenogels (CX) and graphene nanosheets (GNS), possess unique properties such as high surface area, sorption and catalytic characteristics, making them very versatile for many applications in environmental remediation. They are powerful redox mediators (RM) in anaerobic processes, accelerating the rates and extending the level of the reduction of pollutants and, consequently, affecting positively the global efficiency of their partial or total removal. The extraordinary conductive properties of CBM, and the possibility of tailoring their surface to address specific pollutants, make them promising as catalysts in the treatment of effluents containing diverse pollutants. CBM can be combined with magnetic nanoparticles (MNM) assembling catalytic and magnetic properties in a single composite (C@MNM), allowing their recovery and reuse after the treatment process. Furthermore, these composites have demonstrated extraordinary catalytic properties. Evaluation of the toxicological and environmental impact of direct and indirect exposure to nanomaterials is an important issue that must be considered when nanomaterials are applied. Though the chemical composition, size and physical characteristics may contribute to toxicological effects, the potential toxic impact of using CBM is not completely clear and is not always assessed. This review gives an overview of the current research on the application of CBM and C@MNM in bioremediation and on the possible environmental impact and toxicity.

Insight into SO4(-II)- dependent anaerobic methane oxidation in landfill: Dual-substrates dynamics model, microbial community, function and metabolic pathway

In anaerobic landfill, SO42- could serve as electron receptor for methane oxidation. In theory, concentrations of both methane and SO42- should be related to methane oxidation rate. However, the dynamics process has yet to be discovered, and the understanding of metabolic pathways of the sulfate-dependent anaerobic methane oxidation (S-DAMO) process in landfill remains limited. In this study, S-DAMO dynamics was investigated by observing the CH4 oxidation rates under different CH4/ SO42-counter-gradients. The CH4-SO42- dual-substrate model based on MichaeliseMenten equation was got (maximum substrate degradation rate Vmax [22.9 ± 1.31] µmol/[kg·d], half-saturation constants [Formula: see text] , and [Formula: see text] ). High-throughput sequencing analysis indicated Methanobacterials, Methanosarcinales, and Soil Crenarchaeotic were the main functional microorganisms for S-DAMO in landfill. The metabolic pathway of S-DAMO was speculated as the reverse methanogenesis pathway through Phylogenetic Investigation of Communities by Reconstruction of Unobserved States (PICRUST) analysis, while methanogenesis was the methyl nutrition way based on methanol. The enzymes related to the carbon and sulfur cycles and their relative abundances in the microcosms were analyzed to graph the methane metabolic pathway and the sulfur metabolic pathway. The findings provide important parameters for CH4 mitigation in landfills, and give a new insight for understanding S-DAMO metabolic pathway in landfill.

The dosage-effect of biochar on anaerobic digestion under the suppression of oily sludge: Performance variation, microbial community succession and potential detoxification mechanisms

This study investigated the dosage-effect of biochar on the suppressed mesophilic digestion of oily sludge (OS) containing naphthalene (recalcitrant compound) and starch (easily bioavailable substrate). Methanogenesis was inhibited in control with OS, where biomethane yield (63.33 mL/gVS) was obviously lower than theoretical yield (260.55 mL/gVS). With adding optimal dose of biochar (0.60 g/gVS OS), the highest CH₄ yield (138.41 mL/gVS) was 2.19 times of control. Meanwhile, the efficiencies of hydrolysis, acidogenesis and acetogenesis were significantly enhanced. However, excessive biochar (4.80 g/gVS OS) caused negative effects with methanogenic efficiency diminished by 32.5% and lag phase prolonged by 5.72 h. Dissolved organic matter (DOM) analysis showed that humic acid-like and fulvic acid-like components percentages of fluorescence regional integration were decreased because of the adsorption of biochar. In addition, biochar mediating interspecies electron transfer selectively enriched electroactive fermentation bacteria (Clostridium and Bacteroides) and acetoclastic Methanosaeta, which was responsible for promoting mesophilic digestion performance. The functional genes related to metabolism and environmental information processing were potentially activated by biochar. Above results indicate that moderate biochar application may mitigate the bio-toxicity suppression of OS, which help to provide a promising pathway for reinforcing oily wastes bio-treatment.

GO/iron series systems enhancing the pH shock resistance of anaerobic systems for sulfate-containing organic wastewater treatment

In this study, the effect of pH shock during the treatment of sulfate-containing organic wastewater was investigated using an anaerobic fermentation system reinforced with graphene oxide (GO)/iron series systems. The results show that the anaerobic system with the GO/iron series systems exhibited enhanced resistance to pH shock. Among them, the GO/Fe⁰ system had the strongest resistance to pH shock, the systems of GO/Fe₃O₄ and GO/Fe₂O₃ followed close behind, while the blank system performed the worst. After pH shock, the COD_Cr removal rate, SO₄²⁻ removal rate, and gas production of the GO/Fe⁰ group were significantly improved compared with those of the control group by 51.0%, 65.3%, and 34.6%, respectively, while the accumulation of propionic acid was the lowest. Further, detailed microbial characterization revealed that the introduction of the GO/iron series systems was beneficial to the formation of more stable anaerobic co-metabolic flora in the system, and the relative abundance of Geobacter, Clostridium, Desulfobulbus and Desulfovibrio increased after acidic and alkaline shock.

In this paper, we studied the pH shock resistance mechanism of GO/iron series from the perspectives of the treatment effect, changes in effluent pH and VFA, and microbial co-metabolic stability, providing a reference for the practical application.

Anaerobic bacterial responses to carbonaceous materials and implications for contaminant transformation: Cellular, metabolic, and community level findings

Carbonaceous materials (CM) enhance the abundance and activity of bacteria capable of persistent organic (micro)pollutant (POP) degradation. This review synthesizes anaerobic bacterial responses to minimally modified CM in non-fuel cell bioremediation applications at three stages: attachment, metabolism, and biofilm genetic composition. Established relationships between biological behavior and CM surface properties are identified, but temporal relationships are not well understood, making it difficult to connect substratum properties and "pioneer" bacteria with mature microorganism-CM systems. Stark differences in laboratory methodology at each temporal stage results in observational, but not causative, linkages as system complexity increases. This review is the first to critically examine relationships between material and cellular properties with respect to time. The work highlights critical knowledge gaps that must be addressed to accurately predict microorganism-CM behavior and to tailor CM properties for optimized microbial activity, critical frontiers in establishing this approach as an effective bioremediation strategy.

The anaerobic oxidation of methane in paddy soil by ferric iron and nitrate, and the microbial communities involved

The anaerobic oxidation of methane (AOM) mediated by microorganisms is a key process in the reduction of methane emissions, and AOM-coupled electron acceptors have been shown to regulate methane emissions into the atmosphere in marine systems. Paddy fields are a significant source of methane and account for 20% of global methane emissions, but the effect of electron acceptors on the methane emission process in flooded paddy fields has been poorly characterized. This study aimed to determine whether the electron acceptors ferric iron and nitrate, and biochar, acting as an electron shuttle, can regulate the AOM process in paddy soil, with or without interaction between biochar and these two electron acceptors. We also aimed to characterize which microorganisms are actively involved. Here, we added ¹³C-labeled CH₄ (¹³CH₄) into anaerobic microcosms to evaluate the role of electron acceptors by measuring the methane oxidation rate and the enrichment of ¹³C-labeled CO₂ (¹³CO₂). We then combined DNA-stable isotope probing with amplicon sequencing to study the active microorganisms. We found for the first time that, in addition to nitrate, ferric iron can also effectively promote AOM in paddy soil. However, there was no significant effect of biochar. Ferric iron-dependent AOM was mainly carried out by iron-reducing bacteria (Geobacter, Ammoniphilus and Clostridium), and nitrate-dependent AOM was mainly by nitrate-reducing bacteria (Rhodanobacter, Paenibacillus and Planococcus). Our results demonstrate that the AOM process, regulated by the electron acceptors ferric iron and nitrate, can alleviate methane emission from paddy soil. The potentially active microorganisms related to electron acceptor reduction may be crucial for this methane sink and deserve further research.

Trends in the development of innovative nanobiocatalysts and their application in biocatalytic transformations

The ever-growing demand for cost-effective and innocuous biocatalytic transformations has prompted the rational design and development of robust biocatalytic tools. Enzyme immobilization technology lies in the formation of cooperative interactions between the tailored surface of the support and the enzyme of choice, which result in the fabrication of tremendous biocatalytic tools with desirable properties, complying with the current demands even on an industrial level. Different nanoscale materials (organic, inorganic, and green) have attracted great attention as immobilization matrices for single or multi-enzymatic systems. Aiming to unveil the potentialities of nanobiocatalytic systems, we present distinct immobilization strategies and give a thorough insight into the effect of nanosupports specific properties on the biocatalysts' structure and catalytic performance. We also highlight the development of nanobiocatalysts for their incorporation in cascade enzymatic processes and various types of batch and continuous-flow reactor systems. Remarkable emphasis is given on the application of such nanobiocatalytic tools in several biocatalytic transformations including bioremediation processes, biofuel production, and synthesis of bioactive compounds and fine chemicals for the food and pharmaceutical industry.

Anaerobic degradation of xenobiotic organic contaminants (XOCs): The role of electron flow and potential enhancing strategies

In groundwater, deep soil layer, sediment, the widespread of xenobiotic organic contaminants (XOCs) have been leading to the concern of human health and eco-environment safety, which calls for a better understanding on the fate and remediation of XOCs in anoxic matrices. In the absence of oxygen, bacteria utilize various oxidized substances, e.g. nitrate, sulphate, metallic (hydr)oxides, humic substance, as terminal electron acceptors (TEAs) to fuel anaerobic XOCs degradation. Although there have been increasing anaerobic biodegradation studies focusing on species identification, degrading pathways, community dynamics, systematic reviews on the underlying mechanism of anaerobic contaminants removal from the perspective of electron flow are limited. In this review, we provide the insight on anaerobic biodegradation from electrons aspect - electron production, transport, and consumption. The mechanism of the coupling between TEAs reduction and pollutants degradation is deconstructed in the level of community, pure culture, and cellular biochemistry. Hereby, relevant strategies to promote anaerobic biodegradation are proposed for guiding to an efficient XOCs bioremediation.

Enhanced treatment performance of phenol wastewater and membrane antifouling by biochar-assisted EMBR

Biochar-assisted EMBR (BC-assisted EMBR) was built to enhance treatment performance of phenol wastewater and membrane antifouling. BC-assisted EMBR significantly increased phenol degradation efficiency, owing to combined effects of biodegradation, adsorption and electro-catalytic degradation. Meanwhile, BC-assisted EMBR obviously mitigated membrane fouling. The coupling effect of BC and voltage led to the lower N-acyl-homoserine lactones (AHLs) and bound extracellular polymeric substances (bound EPS) contents around and on membrane surface. Protein (PN)/polysaccharide (PS) in bound EPS was decreased, led to the increase of negative charge and decrease of hydrophobicity of sludge, which abated bound EPS adsorption on membrane surface. Microbial community analyses revealed that the coupling effect of BC and voltage could enrich phenol-degraders (e.g., Comamonas), electron transfer genus (Phaselicystis), and biopolymer-degraders (Phaselicystis and Tepidisphaera) in BC-assisted EMBR and on its membrane surface, while decrease biofilm-former (e.g., Acinetobacter) and bound EPS-producer (Devosia), which was beneficial to promote phenol treatment and mitigate membrane fouling.

Interaction of graphene-family nanomaterials with microbial communities in sequential batch reactors revealed by high-throughput sequencing

The accelerated development and application of graphene-family nanomaterials (GFNs) have increased their release to various environments and converged in wastewater treatment plants (WWTPs). However, little is known about the interactions between GFNs and microbes in WWTPs. In this study, the interaction of graphene oxide (GO) or graphene (G) at different concentrations with microbial communities in sequential batch reactors was investigated. Transmission electron microscopy and Raman spectroscopy analyses showed that the structures of GFNs were obviously changed, which suggested GFNs could be degraded by some microbes. Significantly higher DNA concentration and lower cell number in high-concentration GO group were detected by DNA leakage test and qPCR analysis, which confirmed the microbial toxicity of GO. The chemical oxygen demand and ammonia nitrogen removals were significantly affected by G and GO with high concentrations. Further, high-throughput sequencing confirmed the composition and dynamic changes of microbial communities under GFNs exposure. Saccharibacteria genera incertae sedis (12.55-28.05%) and Nakamurella (20.45-29.30%) were the predominant genera at two stages, respectively. FAPROTAX suggested 12 functional groups with obvious changes related to the biogeochemical cycle of C, N and S. Molecular ecological network analysis showed that the networks were more complex in the presence of GFNs, and the increased negative interactions reflected more competition relationships in microbial communities. This study is the first to report the effect of GFNs on network of microbial communities, which provides in-depth insights into the complex and highlights concerns regarding the risk of GFNs to WWTPs.

Effects of biochar on the phenol treatment performance and microbial communities shift in sequencing batch reactors

The extensive application of biochar (BC) attracts concerns regarding its environmental effect. Wastewater treatment systems are potential BC recipients; however, the impacts of BC on these systems are still unclear. In this study, effects of BC on the phenol treatment performance and shift in microbial communities in sequencing batch reactor (SBR) were investigated. The phenol degradation rates were enhanced in all BC-treated SBRs during the whole operation due to promotion of key enzymes involved in phenol degradation. The decrease in abundance of intracellular reactive oxygen species (ROS) in SBRs indicated that BC protected microorganisms by ameliorating phenol toxicity, leading to a decrease in the secretion of extracellular polymeric substances (EPS). The functional groups, protein (C=O, -CO-NH), polysaccharide (C-OH, C-O-C, C-O), and nucleic acids (O-P-O) associated bonds of EPS decreased or disappeared in BC-treated SBRs. Miseq sequencing revealed significant decrease in bacterial diversity and remarkable changes in the bacterial community structure in BC-treated SBRs. Abundances of Comamonas and Cupriavidus increased significantly upon BC exposure, which contributed to phenol degradation. Treatment with relatively high BC dosage exhibited considerable inhibition on Thauera. Canonical correspondence analysis (CCA) indicated that the shift in abundances of these genera was closely associated with BC dosage. This study suggested that BC exerted protective effects on sludge microbes of phenol wastewater treatment systems, while it affected the bacterial community structure and diversity at test concentrations. Thus, this study elucidates the comprehensive effects of BC on wastewater treatment process.