Comparison of activation media and pyrolysis temperature for activated carbons development by pyrolysis of potato peels for effective adsorption of endocrine disruptor bisphenol-A

Composites of sodium alginate based - Functional materials towards sustainable adsorption of benzene phenol derivatives - Bisphenol A/Triclosan

The present study evaluates the adsorption efficiency of low-cost carbonaceous adsorbents as fly ash (FA), saw dust biochar (SDB) (untreated and alkali - treated), live/dead pulverized white rot fungus Hypocrea lixii biomass encapsulated in sodium alginate (SA) against the commercially available activated carbon (AC) and graphene oxide (GO) SA beads for removal of benzene phenol derivatives - Bisphenol A (BPA)/triclosan (TCS). Amongst bi - and tri - composites SA beads, tri-composite beads comprising of untreated flyash - dead fungal biomass - sodium alginate (UFA - DB - SA) showed at par results with commercial composite beads. The tri - composite beads with point zero charge (Ppzc) of 6.2 was characterized using FTIR, XRD, surface area BET and SEM-EDX. The batch adsorption using tri - composite beads revealed removal of 93% BPA with adsorption capacity of 16.6 mg/g (pH 6) and 83.72% TCS with adsorption capacity of 14.23 mg/g (pH 5), respectively at 50 ppm initial concentration with 6 % adsorbent dose in 5 h. Freundlich isotherm favoring multilayered adsorption provided a better fit with r2 of 0.9674 for BPA and 0.9605 for TCS respectively. Intraparticle diffusion model showed adsorption of BPA/TCS molecules to follow pseudo - second order kinetics with boundary layer diffusion governed by first step of fast adsorption and intraparticle diffusion within pores by second slow adsorption step. Thermodynamic parameters (ΔH°, ΔS°, ΔG°) revealed adsorption process as exothermic, orderly and spontaneous. Methanol showed better desorbing efficiency leading to five cycles reusability. The phytotoxicity assay revealed increased germination rate of mung bean (Vigna radiata) seeds, sprinkled with post adsorbed treated water (0 h, 5 h and 7 h) initially spiked with 50 ppm BPA/TCS. Overall, UFA - DB - SA tri - composite beads provides a cost effective and eco - friendly matrix for effective removal of hydrophobic recalcitrant compounds.

Porous activated carbons derived from waste Moroccan pine cones for high-performance adsorption of bisphenol A from water

Porous-activated carbons (ACs) derived from Moroccan pine cones (PC) were synthesised by a two step-chemical activation/carbonisation method using phosphoric acid (PC-H) and zinc chloride (PC-Z) as activating agents and used for the adsorption of bisphenol A (BPA) from water. Several techniques (TGA/DTA, FT-IR, XRD, SEM and BET) were used to determine the surface area and pore characterisation and variations during the preparation of the adsorbents. The modification significantly increased the surface area of both ACs, resulting in values of 1369.03 m2 g-1 and 1018.86 m2 g-1 for PC-H and PC-Z, respectively. Subsequent adsorption tests were carried out, varying parameters including adsorbent dosage, pH, initial BPA concentration, and contact time. Therefore, the highest adsorption capacity was observed when the BPA molecules were in their neutral form. High pH values were found to be unfavourable for the removal of bisphenol A from water. The results showed that BPA adsorption kinetics and isotherms followed pseudo-second-order and Langmuir models. Thermodynamic studies indicated that the adsorption was spontaneous and endothermic. Besides, the regeneration of spent adsorbents demonstrated their reusability. The adsorption mechanisms can be attributed to physical adsorption, hydrogen bonds, electrostatic forces, hydrophobic interactions, and π-π intermolecular forces.

Bisphenol A adsorption using modified aloe vera leaf-wastes derived bio-sorbents from aqueous solution: kinetic, isotherm, and thermodynamic studies

Reactive-oxygen-species are produced more often in the body when bisphenol A (BPA), an endocrine-disrupting-substance, is present. In this investigation, bio-sorbents from an aqueous solution adapted from Aloe-vera were used to survey BPA removal. Aloe-vera leaf wastes were used to create activated carbon, which was then analyzed using Fourier transform infrared (FTIR), Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Thermogravimetric analysis (TGA), Zeta potential, and Brunauer-Emmett-Teller (BET) techniques. It was revealed that the adsorption process adheres to the Freundlich isotherm model with R2>0.96 and the pseudo-second-order kinetic model with R2>0.99 under ideal conditions (pH = 3, contact time = 45 min, concentration of BPA = 20 mg.L-1, and concentration of the adsorbent = 2 g.L-1). After five-cycle, the efficacy of removal was greater than 70%. The removal of phenolic-chemicals from industrial-effluent can be accomplished with the assistance of this adsorbent in a cost-effective and effective-approach.

Cellulose de-polymerization is selective for bioethanol refinery and multi-functional biochar assembly using brittle stalk of corn mutant

As lignocellulose recalcitrance principally restricts for a cost-effective conversion into biofuels and bioproducts, this study re-selected the brittle stalk of corn mutant by MuDR-transposon insertion, and detected much reduced cellulose polymerization and crystallinity. Using recyclable CaO chemical for biomass pretreatment, we determined a consistently enhanced enzymatic saccharification of pretreated corn brittle stalk for higher-yield bioethanol conversion. Furthermore, the enzyme-undigestible lignocellulose was treated with two-step thermal-chemical processes via FeCl2 catalysis and KOH activation to generate the biochar with significantly raised adsorption capacities with two industry dyes (methylene blue and Congo red). However, the desirable biochar was attained from one-step KOH treatment with the entire brittle stalk, which was characterized as the highly-porous nanocarbon that is of the largest specific surface area at 1697.34 m2/g and 2-fold higher dyes adsorption. Notably, this nanocarbon enabled to eliminate the most toxic compounds released from CaO pretreatment and enzymatic hydrolysis, and also showed much improved electrochemical performance with specific capacitance at 205 F/g. Hence, this work has raised a mechanism model to interpret how the recalcitrance-reduced lignocellulose is convertible for high-yield bioethanol and multiple-function biochar with high performance.

The application of P-modified biochar in wastewater remediation: A state-of-the-art review

Phosphorus modified biochar (P-BC) is an effective adsorbent for wastewater remediation, which has attracted widespread attention due to its low cost, vast source, unique surface structure, and abundant functional groups. However, there is currently no comprehensive analysis and review of P-BC in wastewater remediation. In this study, a detailed introduction is given to the synthesis method of P-BC, as well as the effects of pyrolysis temperature and residence time on physical and chemical properties and adsorption performance of the material. Meanwhile, a comprehensive investigation and evaluation were conducted on the different biomass types and phosphorus sources used to synthesize P-BC. This article also systematically compared the adsorption efficiency differences between P-BC and raw biochar, and summarized the adsorption mechanism of P-BC in removing pollutants from wastewater. In addition, the effects of P-BC composite with other materials (element co-doping, polysaccharide stabilizers, microbial loading, etc.) on physical and chemical properties and pollutant adsorption capacity of the materials were investigated. Some emerging applications of P-BC were also introduced, including supercapacitors, CO2 adsorbents, carbon sequestration, soil heavy metal remediation, and soil fertility improvement. Finally, some valuable suggestions and prospects were proposed for the future research direction of P-BC to achieve the goal of multiple utilization.

Removal ibuprofen from aqueous solution by a noval Al-modified biochar

With the increase of organic emissions in production and human life, the pollution control of organic is now an urgent problem in the environmental field. In this study, hydrothermal carbonization rice husk-loaded Al-modified biochar (Al-BC) was synthesized, and the results of scanning electron microscopy could be used to determine that Al oxide composite was loaded on the surface of the material. The specific surface area was 57.049 m2 g-1, pore volume was 0.254 cm3 g-1, and average pore diameter was 8.922 nm for BC and 109.617 m2 g-1, 0.215 cm3 g-1, and 3.969 nm for Al-BC, respectively. The control effects of these two adsorption materials on organic pollutant ibuprofen (IBU) under different pH conditions were also investigated. The research results show that the adsorption capacity of Al-BC (30.24-1.48 mg g-1) is better than BC (19.98-0.92 mg g-1) at pH from 2 to 11. Solution pH plays a crucial role in IBU adsorption from organic solution. The Langmuir fitting results show that at pH = 7, the saturated adsorption capacity of IBU on BC could reach up to 18.68 mg g-1; the adsorption capacity on Al-BC was 60.49 mg g-1. The thermodynamic parameters indicate that the adsorption is spontaneous, endothermic, and increased disorder. The adsorption material prepared in this study could provide a reference for organic pollution control in water.

Efficient Removal of Tetracycline and Bisphenol A from Water with a New Hybrid Clay/TiO2 Composite

New TiO₂ hybrid composites were prepared from kaolin clay, predried and carbonized biomass, and titanium tetraisopropoxide and explored for tetracycline (TET) and bisphenol A (BPA) removal from water. Overall, the removal rate is 84% for TET and 51% for BPA. The maximum adsorption capacities (q_m) are 30 and 23 mg/g for TET and BPA, respectively. These capacities are far greater than those obtained for unmodified TiO₂. Increasing the ionic strength of the solution does not change the adsorption capacity of the adsorbent. pH changes only slightly change BPA adsorption, while a pH > 7 significantly reduces the adsorption of TET on the material. The Brouers-Sotolongo fractal model best describes the kinetic data for both TET and BPA adsorption, predicting that the adsorption process occurs via a complex mechanism involving various forces of attraction. Temkin and Freundlich isotherms, which best fit the equilibrium adsorption data for TET and BPA, respectively, suggest that adsorption sites are heterogeneous in nature. Overall, the composite materials are much more effective for TET removal from aqueous solution than for BPA. This phenomenon is assigned to a difference in the TET/adsorbent interactions vs the BPA/adsorbent interactions: the decisive factor appears to be favorable electrostatic interactions for TET yielding a more effective TET removal.

The role of anthocyanin and kaolinite in modifying cabbage leaves biochar for removal of potentially toxic elements and pharmaceutical from aqueous solution

We investigated the feasibility of two novel engineered biochar composites by pyrolyzing cabbage leaves at 350 °C after pre-treating them with anthocyanin, followed by a post-treatment with kaolinite for the removal of two potentially toxic elements (copper and lead) and a pharmaceutical compound, metoprolol. Results showed that the Kaolinite-biochar composite (KB) exhibited the highest adsorption capacity, 188.67 and 48.07 mg/g for Pb and Cu at pH 5, and the anthocyanin-biochar composite (AB) exhibited the highest adsorption capacity: 41.15 mg/g for metoprolol at pH 6, compared to raw biochar respectively. The enhancement of the adsorption of heavy metal and metoprolol by KB and AB was due to an increase in certain oxygen functional groups, as confirmed by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) results. The pseudo-second order kinetic model, along with Langmuir isotherm model, best described the kinetic and the isotherms for Pb, Cu and metoprolol in KB and AB composites, respectively. FTIR, XPS, and zeta potential measurements indicated that the sorption mechanisms involved electrostatic interaction, ion exchange, and complexation for the metals, while electrostatic interaction, H-bonding, π-πinteraction, and hydrophobic bonding were postulated as the contributing mechanisms in the sorption process of metoprolol. Anthocyanin and kaolinite could potentially be considered as alternative sustainable materials for modifying raw biochar and remediating toxic elements and pharmaceuticals in aqueous media.

Different strengthening effects of amino and nitro groups on the bisphenol A adsorption of an aluminum metal-organic framework in aqueous solution

In recent years, metal-organic frameworks (MOFs) have been employed in numerous applications for adsorption. Researchers synthesize new MOFs by various methods, including the introduction of functional groups. In this study, three different aluminum-based MOFs (with non-functionalized, amino-functionalized, nitro-functionalized) were produced by hydrothermal synthesis and used for investigating typical endocrine disrupting chemicals (EDCs), namely for bisphenol A (BPA) adsorption. We used several methods to characterize the MOFs and conducted batch adsorption experiments to investigate their adsorption properties, and explore the influence of different functional groups on adsorption materials. The specific surface area of Al-MOF-NH₂ is 6 times larger than that of Al-MOF according to the N₂ adsorption and desorption isotherms of the material, that is, the BET of Al-MOF, Al-MOF-NH₂, and Al-MOF-NO₂ were 109.68, 644.03, and 146.60 m²/g. Note that although the same synthesis method is used, pore size is greatly changed because of the different functional groups. Al-MOF and Al-MOF-NO₂ have more mesopores, and Al-MOF-NH₂ is mainly microporous. The BPA adsorption capacities of Al-MOF, Al-MOF-NH₂, and Al-MOF-NO₂ were 46.43, 227.78, and 155.84 mg/L. The outcomes can also be explained by the improved adsorption performance from the addition of amino functional groups. In this research, the adsorption isotherms and adsorption kinetics of the three Al-MOFs for BPA were also investigated to explain the different adsorption properties of various functional groups. The results show that the amino-functionalized materials have remarkable characterization morphologies, uniform particle distributions, appropriate particle sizes, excellent specific surface areas, and superior adsorption effects.

Optimized fabrication of Cu-doped ZnO/calcined CoFe‒LDH composite for efficient degradation of bisphenol a through synergistic visible-light photocatalysis and persulfate activation: Performance and mechanisms

A novel magnetically separable Cu/ZnO/CoFe‒CLDH composite, whose synthesis was optimized using the Taguchi approach, was optimally synthesized by hydrothermally coupling Cu-doped ZnO and calcined CoFe-LDH. The synthesized Cu/ZnO/CoFe‒CLDH was applied to construct a synergistic process of integrating visible-light photocatalysis (VPC) with persulfate activation (PSA) and to degrade bisphenol A (BPA). Various characterizations proved that Cu/ZnO/CoFe‒CLDH possessed excellent physicochemical, optoelectronic and magnetic properties, thereby enhancing the catalytic performance. The Cu/ZnO/CoFe‒CLDH composite achieved highly efficient BPA degradation during the synergistic VPC‒PSA process, and its reaction rate constant (0.74 h^-1) was 6.17-, 4.11-, and 2.85-fold higher than that of Cu/ZnO, CoFe‒CLDH, and Cu/ZnO/CoFe‒CLDH (VPC only), respectively. Moreover, the effects of the catalyst dosage, initial pollutant concentration, solution pH, persulfate dosage and coexisting ions on BPA degradation were comprehensively investigated. Radical-trapping experiments revealed that the contributions of ·OH, SO₄·^‒, ·O₂^-, and ¹O₂ involved in BPA degradation. Based on the intermediates identified by LC/MS, the main BPA degradation pathways were determined, the overall trend of which reflects a decreasing ecotoxicity. This study verified the effectiveness of the synergistic VPC‒PSA process with Cu/ZnO/CoFe‒CLDH, which could be used as a new reference for removing organic micropollutants from water.

Adsorption of Cr(VI) by NaOH-modified microporous activated carbons derived from the wastes of Amaranthus retroflexus, Magnolia soulangeana, and Tanacetum Vulgar L.: mechanism, isotherms, and kinetic studies

The study was designed to synthesize microporous activated carbons from the wastes of three medicinal herbs by NaOH as an activator followed by pyrolysis. The prepared microporous activated carbons R. Weed (Amaranthus retroflexus Redroot pigweed modified with NaOH), S. Bod Magnolia soulangeana Soul-Bod treated with NaOH) and S. TY (Tanacetum Vulgar L. (Tansy) treated with NaOH) were deployed for dangerous Cr(VI) ion remediation from the aquatic system. The synthesized modified biosorbents were described by FT-IR, SEM, EDAX, and BET. Furthermore, it was found that biosorbent made from R. Weed seems to have a surface area of 588.155 m²/g and micropore volume of 0.331Cm³/g whereas biosorbent made from S. Bod and S. TY does have a surface area of 489.613 and 445.615 m²/g respectively. The effects of several variables such as pH, temperature, and contact time were explored. The kinetic studies were accomplished and it was noticed that equilibrium was confirmed at 6 min for R. Weed while at 8 and 10 min for S. Bod and S. TY respectively. The pertinence of different adsorption isotherms like Langmuir, Freundlich, and Temkin was explored. The optimum adsorption capacity for each adsorbent material in respect of monolayer coverage (Q_max) was calculated. The Q_max of Redroot pigweed (R. Weed), Soul-Bod (S. Bod), and Tansy (S. TY) biosorbents were 326.62, 181.69, and 108.14 mg/g respectively. The adsorption kinetics was described using pseudo-first-order and pseudo-second-order equations. Furthermore, it was found that each adsorbent material followed the pseudo-second-order kinetics which affirmed the chemosorption nature of adsorption. The thermodynamic variables that include ΔG, ΔH, and ΔS were determined for each adsorbent material. Moreover, the manufactured R. Weed biosorbent seems to have high recyclability. It will remediate Cr(VI) ions with a maximum remediation efficiency of up to 81% during six cycles of regeneration.

Full-Chain FeCl3 Catalyzation Is Sufficient to Boost Cellulase Secretion and Cellulosic Ethanol along with Valorized Supercapacitor and Biosorbent Using Desirable Corn Stalk

Cellulosic ethanol is regarded as a perfect additive for petrol fuels for global carbon neutralization. As bioethanol conversion requires strong biomass pretreatment and overpriced enzymatic hydrolysis, it is increasingly considered in the exploration of biomass processes with fewer chemicals for cost-effective biofuels and value-added bioproducts. In this study, we performed optimal liquid-hot-water pretreatment (190 °C for 10 min) co-supplied with 4% FeCl₃ to achieve the near-complete biomass enzymatic saccharification of desirable corn stalk for high bioethanol production, and all the enzyme-undigestible lignocellulose residues were then examined as active biosorbents for high Cd adsorption. Furthermore, by incubating Trichoderma reesei with the desired corn stalk co-supplied with 0.05% FeCl₃ for the secretion of lignocellulose-degradation enzymes in vivo, we examined five secreted enzyme activities elevated by 1.3-3.0-fold in vitro, compared to the control without FeCl₃ supplementation. After further supplying 1:2 (w/w) FeCl₃ into the T. reesei-undigested lignocellulose residue for the thermal-carbonization process, we generated highly porous carbon with specific electroconductivity raised by 3-12-fold for the supercapacitor. Therefore, this work demonstrates that FeCl₃ can act as a universal catalyst for the full-chain enhancement of biological, biochemical, and chemical conversions of lignocellulose substrates, providing a green-like strategy for low-cost biofuels and high-value bioproducts.

Synthesis of Activated Porous Carbon from Red Dragon Fruit Peel Waste for Highly Active Catalytic Reduction in Toxic Organic Dyes

In this study, an alternative precursor for production of biomass-derived activated carbon was introduced using dragon fruit (Hylocereus costaricensis) peels. Chemical activators such as FeCl3, MgCl2, ZnCl2 were used in the thermal carbonization process to convert carbon into porous carbon (PC). However, heteroatom-doped PC catalysts including N-, B-, and P-doped carbon catalysts in the field of dye removal is highly desirable. Several approaches (XRD, FE-SEM/TEM, XPS, FT-IR, EDS, and elemental mapping) were employed to examine the surface morphology, surface properties, and elemental composition of the PC catalyst. The catalytic activity of metal-free PC catalyst was demonstrated for methylene blue (MB), crystal violet (CV), and Nile blue (NB) in a mild environment The corresponding rate constant (kapp) values were estimated as 0.2473, 0.3248, and 0.3056 min−1, respectively, for MB, CV, and NB, which were significantly greater than those of numerous reports. It exhibited the best catalytic activity and recyclability. Moreover, the approach proposed here could create new opportunities for the remediation of organic dyes in lakes and industrial wastewater.

Enhanced adsorption of aqueous chlorinated aromatic compounds by nitrogen auto-doped biochar produced through pyrolysis of rubber-seed shell

The adsorption of chlorinated aromatic compounds (CACs) on pristine biochar was often limited. Surface modification can greatly improve the adsorption capacity of biochar. In this work, by pyrolysis activation of rubber-seed shell wastes, nitrogen auto-doped biochar (RSS-NBC) was synthesized and used for purifying CACs-containing wastewater. Systematic characterization results showed that after proper treatment, the as-prepared RSS-NBC had high specific surface area, abundant surface oxygen- and nitrogen-containing functional groups, and nano-scale pore structure. Batch adsorption experiments were conducted with using three typical CACs probing pollutants, i.e. 1,2-dichlorobenzene (1,2-DCB), 2,4-dichlorophenol (2,4-DCP) and 2,4-dichlorobenzoic acid (2,4-DCBA). The adsorption experiments results showed that the maximum adsorption amounts of 1, 2-DCB, 2,4-DCP, and 2,4-DCBA could reach 2284, 1921, and 1142 mg/g at 298.15 K. Moreover, 90% of the equilibrium adsorption amount can be reached within 0.5 h. The adsorption kinetic results showed that the adsorption processes of the three CACs followed the pseudo-second-order rate model and were dominated by chemisorption. Also, the adsorption isotherms of 1, 2-DCB and 2, 4-DCP belonged to the Freundlich model and were valid for multilayer adsorption, while the adsorption of 2,4-DCBA followed Langmuir model and single-layer adsorption. The thermodynamics data indicated that the spontaneous adsorption process of 1, 2-DCB and 2, 4-DCP was endothermic while that of 2,4-DCBA was exothermic. After 5 cycles of adsorption-regeneration, the removal efficiency of RSS-NBC particles still remained more than 80% for the three typical CACs, indicating that it could be reused as an effective and retrievable adsorbent in the treatment of CACs-containing effluents.

Machine learning approaches to predict the photocatalytic performance of bismuth ferrite-based materials in the removal of malachite green

This study focuses on the potential capability of numerous machine learning models, namely CatBoost, GradientBoosting, HistGradientBoosting, ExtraTrees, XGBoost, DecisionTree, Bagging, light gradient boosting machine (LGBM), GaussianProcess, artificial neural network (ANN), and light long short-term memory (LightLSTM). These models were investigated to predict the photocatalytic degradation of malachite green from wastewater using various NM-BiFeO₃ composites. A comprehensive databank of 1200 data points was generated under various experimental conditions. The ten input variables selected were the catalyst type, reaction time, light intensity, initial concentration, catalyst loading, solution pH, humic acid concentration, anions, surface area, and pore volume of various photocatalysts. The MG dye degradation efficiency was selected as the output variable. An evaluation of the performance metrics suggested that the CatBoost model, with the highest test coefficient of determination (0.99) and lowest mean absolute error (0.64) and root-mean-square error (1.34), outperformed all other models. The CatBoost model showed that the photocatalytic reaction conditions were more important than the material properties. The modeling results suggested that the optimized process conditions were a light intensity of 105 W, catalyst loading of 1.5 g/L, initial MG dye concentration of 5 mg/L and solution pH of 7. Finally, the implications and drawbacks of the current study were stated in detail.

Evaluation of Biological Pretreatment of Wormwood Rod Reies with White Rot Fungi for Preparation of Porous Carbon

In this work, the wormwood rod residues are pretreated with white rot fungi as the precursor to preparing porous carbon following a simple carbonization and activation process (denoted herein as FWRA sample). The FWRA sample possesses abundant hierarchical pores structure with high specific surface area (1165.7 m² g^-1) and large pore volume (1.02 cm³ g^-1). As an electrode for supercapacitors, the FWRA sample offers a high specific capacitance of 443.2 F g^-1 at 0.5 A g^-1 and superb rate ability holding a specific capacitance of 270 F g^-1 at 100 A g^-1 in 6 M KOH electrolyte. The corresponding symmetrical capacitor has a superb cyclic stability with a low specific capacitance decay rate of 0.4% after 20,000 cycles at 5 A g^-1 in 1 M Na₂SO₄ electrolyte. Moreover, measurements revealed that when used as adsorbent, the FWRA sample is ideal for removing methyl orange (MO) from water, exhibiting a superior adsorption ability of 260.8 mg g^-1. Therefore, this study is expected to provide a simple and environmentally friendly technique for the generation of value-added and functional porous carbon materials from Chinese medicinal herbal residues, thus offering promising candidates for broad application areas.

Alternative activated/KOH adsorbent for phenol adsorption: experimental, industrial case study and mass transfer interpretation

Removal of phenol from wastewater is essential to achieve permitted concentrations according to the recommendations of USEPA. The adsorption capacity of phenol in activated adsorbent with KOH of Enterolobium contortisiliquum (TAC) was evaluated at different temperatures. The Langmuir isotherm represented the equilibrium data of this study. Thermodynamic process was endothermic, spontaneous, and reversible. The mass transfer parameters ranged from K_E 0.68 to 0.96 × 10^-3 (cm s^-1), Ds 8.95 to 14.35 × 10^-9 (cm² s^-1), and Dp 5.023 × 10^-8 (cm² s^-1). The PVSDM model represented the adsorption kinetics. Intraparticle diffusion limits the mass transfer process Biot > 100. The two-stage process minimized the total amount of TAC required to achieve the permitted specification of phenol concentration in wastewater from different industrial sectors. TAC showed significant performance in the removal of phenol from wastewater.

Ultrathin porous carbon nanosheet as an efficient adsorbent for the removal of bisphenol A: The overlooked role of topological defects

Carbon-based materials are emerging as a type of inexpensive and efficient adsorbent, although their genuine adsorption site is still debatable. Herein, we present a novel approach for designing and constructing an ultra-thin defect-rich hierarchically porous carbon nanosheet (ZG-C). The ZG-C sample demonstrated a high adsorption capacity for bisphenol A (BPA) (602.2 mg/g) along with a fast adsorption process (20 min), and stable reusability (the decline efficiency was 9.14% after five consecutive cycles). Based on comprehensive experiments and a number of characterizations, the high adsorption capacity of ZG-C for BPA was connected with the hierarchical porous structure of ZG-C and multiple intrinsic defects of ZG-C. The results of density functional theory (DFT) further demonstrated that topological defects played an indispensable role in promoting adsorption, and its adsorption energy (-0.595 eV) for BPA was much higher than that of other intrinsic defects. This study not only provides an innovative and simple strategy for preparing hierarchically porous carbon-based adsorbent with abundant intrinsic defects for the efficient removal of BPA, but also significantly contributes to the understanding of the application of carbon-based materials to remove bisphenols.

Biochar application strategies for polycyclic aromatic hydrocarbons removal from soils

Polycyclic aromatic hydrocarbons (PAHs) are known as a hazardous group of pollutants in the soil which causes many challenges to the environment. In this study, the potential of biochar (BC), as a carbonaceous material, is evaluated for the immobilization of PAHs in soils. For this purpose, various bonding mechanisms of BC and PAHs, and the strength of bonds are firstly described. Also, the effect of impressive criteria including BC physicochemical properties (such as surface area, porosity, particle size, polarity, aromaticity, functional group, etc., which are mostly the function of pyrolysis temperature), number of rings in PAHs, incubation time, and soil properties, on the extent and rate of PAHs immobilization by BC are explained. Then, the utilization of BC in collaboration with biological tools which simplifies further dissipation of PAHs in the soil is described considering detailed interactions among BC, microbes, and plants in the soil matrix. The co-effect of BC and biological remediation has been authenticated by previous studies. Moreover, recent technologies and challenges related to the application of BC in soil remediation are explained. The implementation of a combined BC-biological remediation method would provide excellent prospects for PAHs-contaminated soils.

Biosorption of V(V) onto Lantana camara biochar modified by H3PO4: Characteristics, mechanism, and regenerative capacity

Biochar has been widely recognized as an environmentally efficient adsorbent for removing heavy metals. However, considering the weak adsorption performance of the original biochar to the oxygen-containing anion, the adsorption of vanadium by biochar has rarely been investigated. This study proposes that H₃PO₄ activated biochar made from an invasive plant species growing near mines is a novel material to be investigated for V(V) recovery and reuse. As a noxious, invasive plant, Lantana camara L. (LC) has become widely naturalized around the world. Biochar was prepared from LC by pyrolysis at different conditions (200 °C, 350 °C, 500 °C, and 650 °C). The adsorption effect of biochar with and without P pretreatment on V(V) in aqueous solution was compared. The results show that biochar prepared from LC impregnated with H₃PO₄ (MLBC) had the highest adsorption capacity at 500 °C, and the maximal adsorption capacity fitted by Langmuir model was 77.38 mg g^-1, which was considerably higher than that of untreated biochar (LBC, 5.89 mg g^-1). The adsorption procedure was substantially fitted by the Langmuir isotherm and the pseudo-second-order kinetic. Additionally, the interaction of V(V) on MLBC is pH-dependent, and slightly acidic conditions are more favorable for adsorption. The characterization results indicated that electrostatic interaction, complexation reaction, and redox reaction were the primary mechanisms. After three cycles of adsorption, the final maximal adsorption capacity of MLBC remained at 76.03% of that of the virgin sample, demonstrating that MLBC had a recyclable capability to eliminate and restore V(V) from aqueous solutions.

A Study on Machine Learning Methods' Application for Dye Adsorption Prediction onto Agricultural Waste Activated Carbon

The adsorption of dyes using 39 adsorbents (16 kinds of agro-wastes) were modeled using random forest (RF), decision tree (DT), and gradient boosting (GB) models based on 350 sets of adsorption experimental data. In addition, the correlation between variables and their importance was applied. After comprehensive feature selection analysis, five important variables were selected from nine variables. The RF with the highest accuracy (R² = 0.9) was selected as the best model for prediction of adsorption capacity of agro-waste using the five selected variables. The results suggested that agro-waste characteristics (pore volume, surface area, agro-waste pH, and particle size) accounted for 50.7% contribution for adsorption efficiency. The pore volume and surface area are the most important influencing variables among the agro-waste characteristics, while the role of particle size was inconspicuous. The accurate ability of the developed models’ prediction could significantly reduce experimental screening efforts, such as predicting the dye removal efficiency of agro-waste activated carbon according to agro-waste characteristics. The relative importance of variables could provide a right direction for better treatments of dyes in the real wastewater.

Adsorption performance of modified agricultural waste materials for removal of emerging micro-contaminant bisphenol A: A comprehensive review

This review is an attempt to assess the adsorption performance of different green adsorbents derived from agricultural waste materials (AWMs) that were used for the elimination of bisphenol A (BPA) from aqueous matrices. Different processes including grafting, polymerization, activation and chemical treatment have been applied to functionalize and modify agricultural waste materials for the purposes of increasing their adsorptive performances toward BPA. The highest reported adsorption capacity of adsorbent from agricultural waste for the uptake of BPA is the highly microporous carbon adsorbent derived from Argan nut shell (1408 mg g^-1). Hydrogen bonding, hydrophobic and π-π interactions were reported in most studies as the main mechanisms governing the adsorption of BPA onto agricultural waste adsorbents. Equilibrium isotherm and kinetic studies for the uptake of BPA onto agricultural waste adsorbents were best described by Langmuir/Freundlich model and pseudo-second order model, respectively. Despite the effective elimination of BPA by various agricultural waste adsorbents, an appropriate selection of elution solvent is important for effective desorption of BPA from spent adsorbent. To date, ethanol, diethyl ether-methanol, methanol-acetic acid, mineral acids and sodium hydroxide are the most eluents applied for desorption of BPA molecules loaded onto AW-adsorbents. Looking toward the future, studies on the agricultural waste adsorbents based on polymers, activated carbons, nanoparticles and highly microporous carbons should be mostly considered by the researchers toward removing BPA. These future studies should be performed both in laboratory, pilot and industrial scales, and also should report the sustainable techniques for disposal of the spent AW-adsorbents after lose their adsorption performance on BPA.

Enhanced uranium removal from acidic wastewater by phosphonate-functionalized ordered mesoporous silica: Surface chemistry matters the most

The removal of uranium species from aqueous phases using non-hazardous chemicals is still an open challenge, and remediation by adsorption is a prosperous strategy. Among the most crucial concerns regarding the design of an efficient material as adsorbent are, except the cost and the green character, the feasibility to be stable and effective under acidic pH, and to selectively adsorb the desired metal ion (e.g. uranium). Herein, we present a phosphonate functionalized ordered mesoporous silica (OMS-P), prepared by a one-step co-condensation synthesis. The physicochemical features of the material were determined by HR-TEM, XPS, EDX, N₂ sorption, and solid NMR, while the surface zeta potential was also measured. The removal efficiency was evaluated at two different temperatures (20 and 50 °C) in acidic environment to avoid interferences like solid phase formation or carbonate complexation and the adsorption isotherms, including data fitting with Langmuir and Freundlich models and thermodynamic parameters are presented and discussed. The high and homogeneous dispersion of the phosphonate groups within the entire silica's structure led to the greatest reported up-todays capacity (345 mg/g) at pH = 4, which was achieved in less than 10 min. Additionally, OMS-P showed that the co-presence of other polyvalent cation like Eu(III) did not affect the efficiency of adsorption, which occurs via inner-sphere complex formation. The comparison to the non-functionalized silica (OMS) revealed that the key feature towards an efficient, stable, and selective removal of the U(VI) species is the specific surface chemistry rather than the textural and structural features. Based on all the results and spectroscopic validations of surface adsorbed U(VI), the main interactions responsible for the elevated uranium removal were proposed.

Ultrasound-assisted magnetic solid-phase extraction of polycyclic aromatic hydrocarbons and nitrated polycyclic aromatic hydrocarbons from water samples with a magnetic polyaniline modified graphene oxide nanocomposite

A novel magnetic graphene oxide nanocomposite modified with polyaniline (Fe₃O₄@GO-PANI) was synthesized and applied for the magnetic solid-phase extraction of polycyclic aromatic hydrocarbons (PAHs) (i.e. fluorene, phenanthrene and pyrene) and nitrated polycyclic aromatic hydrocarbons (N-PAHs) (i.e. 2-nitrofluorene, 9-nitroanthracene, 1-nitropyrene and 3-nitrofluoranthene) prior to their determination by gas chromatography-mass spectrometry. The prepared nanomaterial was characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform-infrared spectroscopy. The main experimental parameters affecting the extraction and desorption steps of the MSPE procedure were investigated and optimized. Under optimum conditions, coefficients of determination (r²) ranged between 0.9970 and 0.9995, limits of detection (LODs, S/N = 3) ranged between 0.04-0.05 ng mL^-1 for PAHs and 0.01-0.11 ng mL^-1 for N-PAHs, while the relative standard deviation for intra-day and inter-day repeatability were lower than 10.0% for PAHs and N-PAHs. The method was successfully applied to the analysis of tap, mineral and river water samples. Relative recoveries in spiked water samples ranged between from 91.6 to 114% and from 92.3 to 110% for PAHs and N-PAHs, respectively. The proposed method is simple, rapid, sensitive and the Fe₃O₄@GO-PANI sorbent can be reused for at least 15 times without significant decrease in extraction recovery.

Urgently reveal longly hidden toxicant in a familiar fabrication process of biomass-derived environment carbon material

Biomass-derived N-doped carbon (BNC) is an important environmental material and widely used in the fields of water purification and soil remediation. However, the toxicant in the commonly used synthesis process of BNC materials have been largely ignored. Herein, we firstly report the presence of a highly toxic by-product (KCN) in the activation process of BNC materials consequential of the carbothermal reduction reaction. Because this carbothermal reduction reaction also regulates the N-doping and pore development of BNC materials, the KCN content directly relates with the properties of BNC material properties. Accordingly, a high KCN content (∽ 611 mg) can occur in the production process of per g BNC material with high specific surface area (∽ 3600 m²/g). Because the application performance of BNC material is determined by the surface area and available N doping, therefore, production of a BNC material with high performance entails high risk. Undoubtedly, this study proves a completely new risk recognition on a familiar synthesis process of biomass-based material. And, strict protective device should be taken in fabrication process of biomass-derived carbon material.

Production of modified sunflowers seed shells for the removal of bisphenol A

In this present study, an abundant, available lignocellulosic biomass, sunflower seed shells, SSS, was used as a precursor to prepare an effective eco-adsorbent by treatment with H2SO4. A study of the surface characteristics of raw and acid-treated SSS (ACS) has shown that the addition of H2SO4 greatly affected the physicochemical properties of the obtained eco-adsorbent, improving the BET surface area from 6.106 to 27.145 m2 g-1 and surface oxygen-rich functional groups. Batch experiments were performed to assess the removal efficiency of a phenolic compound, bisphenol A (BPA), on the adsorbents. Several parameters were evaluated and are discussed (contact time, pollutant concentration, adsorbent dosage, and pH), determining that the adsorption efficiency of BPA onto SSS was notably improved, from 20.56% to 87.81% when a sulfuric acid solution was used. Different canonical and stochastic isotherm models were evaluated to predict the experimental behaviour. A dynamic study was performed based on the models of reaction kinetics and those of mass transfer. The results showed that the adsorption kinetics of BPA obey the fractal like-kinetic model of Hill for all experimental conditions. The equilibrium data are well suited to the Hill-Sips isotherm model with a determination coefficient >0.999. The kinetic modelling also indicates that the adsorption processes of BPA onto ACS are exothermic and proceed through a physical mechanism. A mass transfer study, using simplified models, proved that the process is controlled by intraparticle and film resistances to mass transfer of the BPA.

Clay-activated carbon adsorbent obtained by activation of spent bleaching earth and its application for removing Pb(II) ion

BE/C-A750-1/1 is prepared by carbonizing SBE and then activating with KOH. BE/C-A750-1/1 has good adsorption capacity for Pb(II), and the adsorption capacity for Pb(II) is 206.65 mg/g. The harmful effects of coexisting cations are listed in ascending order: K⁺ < Na⁺ < Mg²⁺. Adsorption and desorption studies show that the adsorption capacity of BE/C-A750-1/1 for Pb(II) after adsorption and desorption 3 times is 183.62 mg/g. The adsorption mechanism mainly includes electrostatic attraction, ion exchange, physical adsorption, and chemical complexation. This suggests that activated BE/C may be a promising candidate for removing Pb(II) from industrial wastewater. Clay/carbon nanocomposites were prepared by carbonizing and activating the spent bleaching earth served as adsorbents for the efficient removal of Pb(II) from wastewater.

Current State of Porous Carbon for Wastewater Treatment

Porous materials constitute an attractive research field due to their high specific surfaces; high chemical stabilities; abundant pores; special electrical, optical, thermal, and mechanical properties; and their often higher reactivities. These materials are currently generating a great deal of enthusiasm, and they have been used in large and diverse applications, such as those relating to sensors and biosensors, catalysis and biocatalysis, separation and purification techniques, acoustic and electrical insulation, transport gas or charged species, drug delivery, and electrochemistry. Porous carbons are an important class of porous materials that have grown rapidly in recent years. They have the advantages of a tunable pore structure, good physical and chemical stability, a variable specific surface, and the possibility of easy functionalization. This gives them new properties and allows them to improve their performance for a given application. This review paper intends to understand how porous carbons involve the removal of pollutants from water, e.g., heavy metal ions, dyes, and organic or inorganic molecules. First, a general overview description of the different precursors and the manufacturing methods of porous carbons is illustrated. The second part is devoted to reporting some applications such using porous carbon materials as an adsorbent. It appears that the use of porous materials at different scales for these applications is very promising for wastewater treatment industries.

Methylene blue adsorption by timbaúva (Enterolobium contortisiliquum)-derived materials

Liquid effluents from various dyeing industries often have a high concentration of dyes that diffuse into river systems and can be toxic and non-degradable in the environment. In this study, the potential of the use of timbaúva seed husks in the preparation of four adsorbents tested in the removal of methylene blue was analyzed: in natura, chemically activated material (q_max = 1.24 ± 0.04 mg g^-1), carbonized (q_max = 1.96 ± 0.03 mg g^-1), and activated carbon (q_max = 1.983 ± 0.04 mg g^-1). The adsorbents were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and CHN elemental analysis to assist in the proposed dye adsorption mechanism in the adsorbents tested. In the adjustment of the kinetic parameters, the pseudo-second order model was predominant by the statistical analysis of the ARE and R². The carbonized samples were better adjusted to Langmuir isotherms. The removal efficiency of the methylene blue dye in aqueous solutions at the concentrations and conditions studied was 86.78%. The coal from the seed husks of timbaúva has shown excellent performance in adsorption of the methylene blue dye and, therefore, can have technological application.

Preparation of sludge-based hydrochar at different temperatures and adsorption of BPA

This study sought a new way to utilize sludge as a low cost and efficient adsorbent. Preparation of sludge adsorbent by hydrothermal carbonization was done at different temperatures (160-250 °C). Various characterization techniques were used in this study including elemental analysis, Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS). The adsorption performance of the organic matter was analyzed by adsorption experiments with the endocrine disruptor bisphenol A (BPA). Results showed that as the hydrothermal temperature increased, the solid yield of hydrochar decreased from 84.73% to 55.19%, and the maximum specific surface area was 11.9 m²/g. Elemental analysis showed that the hydrochar contains more aromatic carbon than the raw sludge. It was found using the FT-IR and XPS that the hydrochar retains a large amount of oxygen-containing functional groups on the surface after hydrothermal treatment. Hydrochar can be used as an organic-pollutant adsorbent in water; it has a good adsorption effect on BPA and the removal rate can reach 96%. The adsorbed hydrochar can be hydrothermally retreated and returned to the sewage treatment plant for reuse.

Adsorption characteristics and mechanism of norfloxacin in water by γ-Fe2O3@BC

Using waste pomelo peel as raw material, pomelo peel-based biochar (BC) was prepared by pyrolysis at 400 °C, and the pomelo peel-based biochar was prepared by loading γ-Fe₂O₃ onto the surface of the pomelo peel-based biochar by unlimited oxygen chemical precipitation. The results showed that the pomelo peel biochar loaded with γ-Fe₂O₃ had higher specific surface area and larger pore volume. The load of γ-Fe₂O₃ gives γ-Fe₂O₃@BC excellent magnetic separation ability, and its magnetic saturation intensity is as high as 30.60 emu/g. BC and γ-Fe₂O₃@BC were applied to remove norfloxacin (NOR) from a water body. It was found that the adsorption of NOR by both of them followed the pseudo-second-order kinetic model. The adsorption isotherm mainly conforms to the Sips model, and the adsorption process of NOR is a spontaneous endothermic reaction. The pH and ionic strength have a great influence on the adsorption of NOR by BC and γ-Fe₂O₃@BC, and they play a role mainly by influencing the morphology of NOR in water. The adsorption mechanism showed that cation exchange and hydrogen bonding were the main forces for BC to adsorb NOR. Moreover, the γ-Fe₂O₃ particles enhanced the hydrophobicity of the pomelo peel-based biochar, making the hydrophobicity become the main force for the adsorption of NOR by the γ-Fe₂O₃@BC. The adsorption-desorption experiment showed that after four cycles of recycling, the adsorption capacity of γ-Fe₂O₃@BC for NOR was still up to 61.43% of the initial adsorption capacity, and it had a good recycling property.

Preparation and characterization of activated carbons obtained from the waste materials impregnated with phosphoric acid(V)

In the paper spent coffee grounds were used as a precursor to obtain activated carbons. The raw material was impregnated with phosphoric acid(V) at the different impregnations ratios: 0.5, 1, 1.5, 2. Carbonization was carried out according to two procedures differing in activation atmosphere (N2 or CO2). The obtained activated carbons were characterized on the basis of low-temperature nitrogen adsorption/desorption, thermal analysis, potentiometric titration method, X-ray diffraction, Raman spectroscopy and scanning electron microscopy. Carbons obtained according to procedure 2 (activation in CO2) were characterized by better developed porosity, e.g. surface (SBET to 720.9 m2/g) and pore volume (Vp to 0.334 cm3/g). All obtained carbons had surface acidic (mainly carboxyl) groups and exhibited the amorphous structure. The thermal analysis showed that the obtained materials were thermally stable up to the temperature ~ 420 °C.

Adsorption Characteristics and Mechanism of Bisphenol A by Magnetic Biochar

In this paper, biochar (BC) was prepared from discarded grapefruit peel and modified to prepare magnetic biochar (MBC). Physical and chemical properties of BC and MBC were characterized, and the results showed that the type of iron oxide loaded by MBC was γ-Fe₂O₃. Compared with BC, MBC has a larger specific surface area and pore volume, with more oxygen-containing functional groups on the surface. BC and MBC were used to adsorb and remove endocrine-disrupting chemical (EDC) bisphenol A (BPA) from simulated wastewater. The results showed that the adsorption kinetics and adsorption isotherm of BPA adsorption by BC and MBC were mainly in accordance with the pseudo-second-order kinetics model and the Langmuir model. This indicates that the adsorption of BPA on BC and MBC is mainly a chemically controlled monolayer adsorption. Adsorption thermodynamics show that BC and MBC adsorption of BPA is a spontaneous exothermic reaction, and lowering the temperature is conducive to the adsorption reaction. The effect of solution pH on the adsorption of BPA by both was significant. The optimum pH for BC and MBC to absorb BPA was 6 and 3, respectively. The concentration of Na⁺ in the range of 0–0.10 mol·L⁻¹ can promote the adsorption of BPA to MBC. MBC loaded with γ-Fe₂O₃ not only has excellent magnetic separation ability, but can also reach about 80% of the initial adsorption capacity after four cycles of adsorption. By analyzing the adsorption mechanism, it was found that the H-bond and the π–π electron donor–acceptor interaction (EDA) were the main forces for BC and MBC to adsorb BPA.

Confined Red Phosphorus in Edible Fungus Slag-Derived Porous Carbon as an Improved Anode Material in Sodium-Ion Batteries

Red phosphorus (RP) as the anode material for the sodium-ion battery (SIB) possesses a high energy density, but the poor electronic conductivity and huge volume change during Na⁺ insertion/extraction restrict its application. In this work, the edible fungus slag-derived porous carbon (PC) is adopted as a carbon matrix to combine with RP to form PC@RP composites through a facile vaporization-condensation approach. The conductive porous carbon architecture improves the transfer of electron and Na⁺ in the composite. The robust carbon framework together with the chemical bonding between PC and RP effectively buffer the huge volumetric change of RP. As a result, the PC@RP composite material delivers a specific capacity of 655.1 mA h g^-1 at 0.1 A g^-1 with a capacity retention of 87% after 100 charging/discharging cycles. In particular, the full SIB assembled with P2-Na_2/3Ni_1/3Mn_1/3Ti_1/3O₂ as the cathode material and PC@RP as the anode material exhibits a specific capacity of 77.3 mA h g^-1 (based on the mass of cathode material) at 0.5 C, and 85% capacity is retained after 100 charging/discharging cycles.

Edible fungus slag derived nitrogen-doped hierarchical porous carbon as a high-performance adsorbent for rapid removal of organic pollutants from water

In this work, agricultural waste edible fungus slag derived nitrogen-doped hierarchical porous carbon (EFS-NPC) was prepared by a simple carbonization and activation process. Owing to the biodegradation and infiltrability of hyphae, this EFS-NPC possessed an ultra-high specific surface area (3342 m²/g), large pore volume (1.84 cm³/g) and abundant micropores and mesopores. The obtained EFS-NPC could effectively adsorb bisphenol A (BPA) with the maximal adsorption capacity of 1249 mg/g and the removal process reached 89.9% of the equilibrium uptake in the first 0.5 h. Besides, the EFS-NPC showed much better removal performance towards 2,4-dichlorophenol (2,4-DCP) and methylene blue (MB) than commercial activated carbons (Norit RO 0.8 and DARCO granular activated carbon). Furthermore, adsorption isotherms, thermodynamics and kinetics researches indicated that the adsorption process of BPA was monolayer, exothermic and spontaneous. This research has given evidence that the low-cost EFS-NPC can serve as a high-efficient adsorbent for removing organic contaminants from water.

Production and characterisation of activated carbon and carbon nanotubes from potato peel waste and their application in heavy metal removal

Herein, activated carbon (AC) and carbon nanotubes (CNTs) were synthesised from potato peel waste (PPW). Different ACs were synthesised via two activation steps: firstly, with phosphoric acid (designated PP) and then using potassium hydroxide (designated PK). The AC produced after the two activation steps showed a surface area as high as 833 m2 g-1 with a pore volume of 0.44 cm3 g-1, where the raw material of PPW showed a surface area < 4 m2 g-1. This can help aid and facilitate the concept of the circular economy by effectively up-cycling and valorising waste lignocellulosic biomass such as potato peel waste to high surface area AC and subsequently, multi-walled carbon nanotubes (MWCNTs). Consequently, MWCNTs were prepared from the produced AC by mixing it with the nitrogen-based material melamine and iron precursor, iron (III) oxalate hexahydrate. This produced hydrophilic multi-wall carbon nanotubes (MWCNTs) with a water contact angle of θ = 14.97 °. Both AC and CNT materials were used in heavy metal removal (HMR) where the maximum lead absorption was observed for sample PK with a 84% removal capacity after the first hour of testing. This result signifies that the synthesis of these up-cycled materials can have applications in areas such as wastewater treatment or other conventional AC/CNT end uses with a rapid cycle time in a two-fold approach to improve the eco-friendly synthesis of such value-added products and the circular economy from a significant waste stream, i.e., PPW. Graphical abstract .

A Review of Chemicals to Produce Activated Carbon from Agricultural Waste Biomass

The choice of activating agent for the thermochemical production of high-grade activated carbon (AC) from agricultural residues and wastes, such as feedstock, requires innovative methods. Overcoming energy losses, and using the best techniques to minimise secondary contamination and improve adsorptivity, are critical. Here, we review the importance and influence of activating agents on agricultural waste: how they react and compare conventional and microwave processes. In particular, adsorbent pore characteristics, surface chemistry interactions and production modes were compared with traditional methods. It was concluded that there are no best activating agents; rather, each agent reacts uniquely with a precursor, and the optimum choice depends on the target adsorbent. Natural chemicals can also be as effective as inorganic activating agents, and offer the advantages that they are usually safe, and readily available. The use of a microwave, as an innovative pyrolysis approach, can enhance the activation process within a duration of 1–4 h and temperature of 500–1200 °C, after which the yield and efficiency decline rapidly due to molecular breakdown. This study also examines the biomass milling process requirements; the influence of the dielectric properties, along with the effect of washing; and experimental setup challenges. The microwave setup system, biomass feed rate, product delivery, inert gas flow rate, reactor design and recovery lines are all important factors in the microwave activation process, and contribute to the overall efficiency of AC preparation. However, a major issue is a lack of large-scale industrial demonstration units for microwave technology.

Optimized synthesis of a core-shell structure activated carbon and its adsorption performance for Bisphenol A

The presence of endocrine disrupting chemicals (EDCs) in the environmental water poses a serious threat which requires strong practical solutions. The existing activated carbon-based adsorbents exhibit a number of limitations hindering for their use in adsorption in an aquatic environment. In this work, a controlled technique was used to make a protected Core-Shell structure Activated Carbon (CSAC) material with a smaller size (0.82 cm), thinner shell thickness (0.083 cm) and high mechanical strength (2.41 MPa). The experimental results demonstrated that the sizes of shell precursors used for preparing the ceramic shell had a pronounced influence on the produced material. The shell was prepared by using a mixture of kaolinite (400 mesh) and coal fly ash (100 mesh). The pellet activated carbon core was synthesized by a pelletizing method using powder activated carbon (92%) mixed with the binder (8%) from cassava splinters. The kinetic study evidenced that the performance of the material fitted better for pseudo-second-order kinetic and the intraparticle diffusion. Furthermore, the maximum amount of Bisphenol A (BPA) adsorption by CSAC fitting to Langmuir model was 28.5 mg g^-1. The BPA adsorption by CSAC was an endothermic process. Therefore, this material could be applied in the remediation of various aquatic EDCs.

Graphene Oxide Based Magnetic Nanocomposites with Polymers as Effective Bisphenol-A Nanoadsorbents

Magnetic graphene oxide was impregnated with polymers for the preparation of nanocomposite adsorbents to be examined for the adsorptive removal of a typical endocrine disruptor, bisphenol–A (BPA) from aqueous solutions. The polymers used were polystyrene, chitosan and polyaniline. The nanocomposites prepared were characterized for their structure, morphology and surface chemistry. The nanocomposites presented an increase adsorptive activity for BPA at ambient conditions, compared to pure magnetic oxide, attributed to the synergistic effect of the polymers and the magnetic graphene oxide. The increased adsorption of BPA exhibited by the nanocomposites with chitosan and polyaniline could be attributed to the contribution of amine groups.

Preparation of mesoporous activated carbon from date stones for the adsorption of Bemacid Red

This work concerns the elimination of the organic pollutant; Bemacid Red (BR), a rather persistent dye present in wastewater from the textile industry in western Algeria, by adsorption on carbon from an agricultural waste in the optimal conditions of the adsorption process. An active carbon was synthesized by treating an agro-alimentary waste, the date stones that are very abundant in Algeria, physically and chemically. Sample after activation (SAA) with phosphoric acid was highly efficient for the removal of BR. The characterization of this porous material has shown a specific surface area that exceeds 900 m²/g with the presence of mesopores. The iodine value also indicates that the activated carbon obtained has a large micro porosity. The reduction of the infrared spectroscopy (FTIR) bands reveals that the waste has been synthesized and activated in good conditions. Parameters influencing the adsorption process have been studied and optimized, such as contact time, adsorbent mass, solution pH, initial dye concentration and temperature. The results show that for a contact time of 60 min, a mass of 0.5 g and at room temperature, the adsorption rate of the BR by the SAA is at its maximum. Pseudo-first-order, pseudo-second-order and intraparticle diffusion models were studied to analyse adsorption kinetics. The result shows the adsorption kinetic is best with the pseudo-second-order model. In this study, Langmuir, Freundlich and Temkin isotherms were investigated for adsorption of BR onto SAA. The Freundlich and Temkin isotherms have the highest correlations coefficients. The suggested adsorption process involves multilayer adsorption with the creation of chemical bonds. The mechanism of adsorption of BR by SAA is spontaneous and exothermic, and the Gibbs free energy values confirm that the elimination of the textile dye follows a physisorption.

Removal of bisphenol A by Fe-impregnated activated carbons

A commercial wood-based activated carbon and the oxidized counterpart were impregnated with iron. The two Fe-impregnated carbons were prepared and characterized for their iron content, textural characteristics, surface chemistry, and their performance for bisphenol A adsorption. Batch adsorption experiments were conducted to study the effect of pH, ionic strength, kinetics, and thermodynamic equilibrium. Equilibrium adsorption data were described by both Langmuir and Freundlich isotherms. The iron impregnated activated carbon and the oxidized impregnated activated carbon presented maximum adsorption capacities of 785.65 and 469.78 mg/g, respectively, while adsorption followed second-order rate kinetics for both impregnated carbons. According to the thermodynamic parameters (ΔΗο, ΔSo, ΔGo), the adsorption is a spontaneous, exothermic, and physical process. Fenton-driven experiments conducted at different molar ratios of [H₂O₂]/[BPA] showed efficient degradation of BPA in spent Fe-impregnated carbons up to 82-95%, with traces of hydroxylated products.

JF, Fernández Hincapie JJ. Preparación y Caracterización de Carbones Activados a partir de un Carbón Mineral de la Cuenca del Cesar (Colombia)

En este trabajo se prepararon carbones activados a partir de un carbón bituminoso, mediante procesos de activación física y química. La activación física con vapor de agua (H2O) se realizó a temperaturas de 700 y 800°C y la activación química utilizando ZnCl2 0.2 N a 600, 700 y 800°C. Los carbones activados se caracterizaron mediante diferentes técnicas, como punto de carga cero (PZC), espectroscopia infrarroja (IR, DRIFT), área superficial y microscopia electrónica de barrido (SEM-EDX). Se obtuvieron carbones activados microporosos con áreas superficiales hasta de 351 m2/g con un volumen de poro de 0.15 cm3/g y un tamaño promedio de poro de 19.4 Å. El carbón activado de mayor área superficial fue apto para la remoción del azul de metileno cuya isoterma de adsorción se ajusta al modelo de Langmuir y la cinética de adsorción se ajusta al modelo pseudo-segundo orden y de difusión intraparticular.