Boron-doped diamond electrode: Preparation, characterization and application for electrocatalytic degradation of m-dinitrobenzene

Effects of anode materials on nitrate reduction and microbial community in a three-dimensional electrode biofilm reactor with sulfate

Graphite rod corrosion and peeling are serious problems in three-dimensional electrode biofilm reactors (3D-BERs). In this study, titanium rods, titanium suboxide-coated titanium rods and graphite rods were used as anodes to investigate the effect of anodic materials on the electrochemical and bioelectrochemical reduction of nitrate and sulfate. The results showed that the reactor with the titanium suboxide-coated titanium rod anode (3D-ER-T) exhibited a stable NO3--N removal efficiency (46%-95%) with a current range of 160-320 mA in the electrochemical reduction process. In the bioelectrochemical reduction, the removal efficiencies of NO3--N and SO42- and nitrogen selectivity in the 3D-BER with titanium suboxide-coated titanium rod anode (3D-BER-T) were higher than those in the 3D-BER with titanium suboxide-coated graphite rod anode (3D-BER-G). The removal efficiencies of NO3--N and SO42- and nitrogen selectivity were 92%, 43% and 86%, respectively, in 3D-BER-T under 320 mA and HRT 12 h. Anode materials affected the microbial community. Hydrogenophaga and Dethiobacter were the dominant bacteria in 3D-BER-T, while OPB41 and Sulfurospirillum were dominant in 3D-BER-G. Nitrate and sulfate were effectively removed in 3D-BER-T by the synergistic work of electrochemical reduction, bioelectrochemical reduction and indirect electrochemical reduction. The resupply/reserve mode of the electron donor promoted the load of shock resistance of 3D-BER-T via the sulfur cycle. Titanium suboxide coating could significantly enhance the anti-corrosion ability of matrix anodes.

Efficient electrochemical degradation of X-GN dye wastewater using porous boron-doped diamond electrode

Surface porous Ti substrates were obtained by electrodeposition-hot melt-alkali etching. Porous-Ti/BDD and flat-Ti/BDD electrodes were prepared for comparative study. The results of SEM, Raman, and XRD analyses show that the BDD films of these two electrodes had good uniformity and stable quality. The electrochemical window (EW) and electrochemical-active surface area (EASA) of the porous-Ti/BDD electrode is as high as 4.21 V and 22.78 cm² (11.39 cm²/cm²), respectively. Furthermore, the electrochemical catalytic performance and degradation mechanism of porous-Ti/BDD electrode as the anode were studied by the electrolysis of Active Orange dye X-GN (X-GN), and the optimal electrochemical degradation operating parameters were obtained. The results show that when the degradation time was 50 min, the X-GN was completely decolorized. The TOC removal rate reached 69.24%, and the energy consumption was 5.62 kWh m^-3. The contribution rate of •OH and SO₄^•- was calculated to be 91.40% and 1.26% by radical quenching experiments, respectively, indicating that the active substances in the degradation system were mainly •OH and SO₄^•-. The high specific surface characteristics of porous-Ti/BDD electrode enhanced its electrochemical oxidation advantages, and it showed a high degradation efficiency and low energy consumption for the treatment of X-GN simulated wastewater.

Progress in Preparation and Application of Titanium Sub-Oxides Electrode in Electrocatalytic Degradation for Wastewater Treatment

To achieve low-carbon and sustainable development it is imperative to explore water treatment technologies in a carbon-neutral model. Because of its advantages of high efficiency, low consumption, and no secondary pollution, electrocatalytic oxidation technology has attracted increasing attention in tackling the challenges of organic wastewater treatment. The performance of an electrocatalytic oxidation system depends mainly on the properties of electrodes materials. Compared with the instability of graphite electrodes, the high expenditure of noble metal electrodes and boron-doped diamond electrodes, and the hidden dangers of titanium-based metal oxide electrodes, a titanium sub-oxide material has been characterized as an ideal choice of anode material due to its unique crystal and electronic structure, including high conductivity, decent catalytic activity, intense physical and chemical stability, corrosion resistance, low cost, and long service life, etc. This paper systematically reviews the electrode preparation technology of Magnéli phase titanium sub-oxide and its research progress in the electrochemical advanced oxidation treatment of organic wastewater in recent years, with technical difficulties highlighted. Future research directions are further proposed in process optimization, material modification, and application expansion. It is worth noting that Magnéli phase titanium sub-oxides have played very important roles in organic degradation. There is no doubt that titanium sub-oxides will become indispensable materials in the future.

Nano-Structured Carbon: Its Synthesis from Renewable Agricultural Sources and Important Applications

Carbon materials are versatile in nature due to their unique and modifiable surface and ease of production. Nanostructured carbon materials are gaining importance due to their high surface area for application in the energy, biotechnology, biomedical, and environmental fields. According to their structures, carbon allotropes are classified as carbon nanodots, carbon nanoparticles, graphene, oxide, carbon nanotubes, and fullerenes. They are synthesized via several methods, including pyrolysis, microwave method, hydrothermal synthesis, and chemical vapor deposition, and the use of renewable and cheaper agricultural feedstocks and reactants is increasing for reducing cost and simplifying production. This review explores the nanostructured carbon detailed investigation of sources and their relevant reports. Many of the renewable sources are covered as focused here, such as sugar cane waste, pineapple, its solid biomass, rise husk, date palm, nicotine tabacum stems, lapsi seed stone, rubber-seed shell, coconut shell, and orange peels. The main focus of this work is on the various methods used to synthesize these carbon materials from agricultural waste materials, and their important applications for energy storage devices, optoelectronics, biosensors, and polymer coatings.

Comparative electrochemical oxidation of the secondary effluent of petrochemical wastewater with electro-Fenton and anodic oxidation with supporting electrolytes

Electro-Fenton (EF) oxidation has high oxidation abilities and is widely used in the treatment of biorefractory and chemically refractory organic wastewater. However, it generates a large amount of iron sludge, which limits large-scale application. In this work, the comparative study of EF oxidation and anodic oxidation (AO) of the secondary effluent of petrochemical wastewater using boron doped diamond anode is carried out. In EF oxidation, the effects of Fe²⁺ concentration, pH value, and current density are investigated. The optimal conditions consist of the following: Fe²⁺ concentration of 1.5 mmol·L^-1, pH of 4, and current density of 10 mA·cm^-2. In AO process, the effect of adding SO42-, Cl^-, NO3-, PO43-, and CO32- is investigated; the optimal conditions can be obtained by adding a Na₂SO₄ solution (0.075 mol·L^-1). When compared with AO, although EF oxidation has a higher treatment efficiency, its energy consumption is higher, and the generated effluent (with 155 g of iron sludge·m^-3) dramatically increases the post-treatment cost, thereby limiting its large-scale application. For AO with Na₂SO₄ solution (0.075 mol·L^-1) and a COD removal efficiency of 70%, the corresponding treatment time is 1.34 h and the energy consumption is 2.44 kWh·m^-3.

Low-coherence photonic method of electrochemical processes monitoring

We present an advanced multimodality characterization platform for simultaneous optical and electrochemical measurements of ferrocyanides. Specifically, we combined a fiber-optic Fabry–Perot interferometer with a three-electrode electrochemical setup to demonstrate a proof-of-principle of this hybrid characterization approach, and obtained feasibility data in its monitoring of electrochemical reactions in a boron-doped diamond film deposited on a silica substrate. The film plays the dual role of being the working electrode in the electrochemical reaction, as well as affording the reflectivity to enable the optical interferometry measurements. Optical responses during the redox reactions of the electrochemical process are presented. This work proves that simultaneous opto-electrochemical measurements of liquids are possible.

Co/Sm-modified Ti/PbO2 anode for atrazine degradation: Effective electrocatalytic performance and degradation mechanism

In this work, Ti/PbO₂-Co-Sm electrode has been successfully prepared using electrodeposition and further applied for the electrocatalysis of atrazine (ATZ) herbicide wastewater. As expected, Ti/PbO₂-Co-Sm electrode displays highest oxygen evolution potential, lowest charge transfer resistance, longest service lifetime and most effective electrocatalytic activity compared with Ti/PbO₂, Ti/PbO₂-Sm and Ti/PbO₂-Co electrodes. Orthogonal and single factor experiments are designed to optimize the condition of ATZ degradation. The maximum degradation efficiency of 92.6% and COD removal efficiency of 84.5% are achieved in electrolysis time 3 h under the optimum condition (current density 20 mA cm^-2, Na₂SO₄ concentration 8.0 g L^-1, pH 5 and temperature 35 °C). In addition, Ti/PbO₂-Co-Sm electrode exhibits admirable recyclability in degradation progress. The degradation of ATZ is accomplished by indirect electrochemical oxidation and ∙OH is tested as the main active substance in ATZ oxidation. The possible degradation mechanism of ATZ has been proposed according to the degradation intermediates detected by LC-MS. This research suggests that Ti/PbO₂-Co-Sm is a promising electrode for ATZ degradation.

Thermal decomposition based fabrication of dimensionally stable Ti/SnO2-RuO2 anode for highly efficient electrocatalytic degradation of alizarin cyanin green

In this work, Ti/SnO₂-RuO₂ dimensionally stable anode has been successfully fabricated via thermal decomposition method and further used for highly efficient electrocatalytic degradation of alizarin cyanin green (ACG) dye wastewater. The morphology, crystal structure and composition of Ti/SnO₂-RuO₂ electrode are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray fluorescence spectroscopy (XRF), respectively. The result of accelerated life test suggests that as-prepared Ti/SnO₂-RuO₂ anode exhibits excellent electrochemical stability. Some parameters, such as reaction temperature, initial pH, electrode spacing and current density, have been investigated in detail to optimize the degradation condition of ACG. The results show that the decolorization efficiency and chemical oxygen demand removal efficiency of ACG reach up to 80.4% and 51.3% after only 40 min, respectively, under the optimal condition (reaction temperature 25 °C, pH 5, electrode spacing 1.0 cm and current density 3 mA cm^-2). Furthermore, the kinetics analysis reveals that the process of electrocatalytic degradation of ACG follows the law of quasi-first-order kinetics. The excellent electrochemical activity demonstrates that the Ti/SnO₂-RuO₂ electrode presents a favorable application prospect in the electrochemical treatment of anthraquinone dye wastewater.

Fabrication of Co/Pr co-doped Ti/PbO2 anode for efficiently electrocatalytic degradation of β-naphthoxyacetic acid

The existence of β-naphthoxyacetic acid (BNOA) pesticide in water system has aroused serious environmental problem because of its potential toxicity for humans and organisms. Therefore, exploiting an efficient method without secondary pollution is extremely urgent. Herein, a promising Ti/PbO₂-Co-Pr composite electrode has been successfully fabricated through simple one-step electrodeposition for efficiently electrocatalytic degradation of BNOA. Compared with Ti/PbO₂, Ti/PbO₂-Co and Ti/PbO₂-Pr electrodes, Ti/PbO₂-Co-Pr electrode with smaller pyramidal particles possesses higher oxygen evolution potential, excellent electrochemical stability and outstanding electrocatalytic activity. The optimal degradation condition is assessed by major parameters including temperature, initial pH, current density and Na₂SO₄ concentration. The degradation efficiency and chemical oxygen demand removal efficiency of BNOA reach up to 94.6% and 84.6%, respectively, under optimal condition (temperature 35 °C, initial pH 5, current density 12 mA cm^-2, Na₂SO₄ concentration 8.0 g L^-1 and electrolysis time 3 h). Furthermore, Ti/PbO₂-Co-Pr electrode presents economic energy consumption and superior repeatability. Finally, the possible degradation mechanism of BNOA is put forward according to the main intermediate products identified by liquid chromatography-mass spectrometer. The present research paves a new path to degrade BNOA pesticide wastewater with Ti/PbO₂-Co-Pr electrode.

Conductive diamond: synthesis, properties, and electrochemical applications

This review summarizes systematically the growth, properties, and electrochemical applications of conductive diamond.

Ti/PbO2-Sm2O3 composite based electrode for highly efficient electrocatalytic degradation of alizarin yellow R

In this work, a novel Ti/PbO₂-Sm₂O₃ composite electrode with high electrocatalytic activity is successfully fabricated via simple electrodeposition method and further investigated for electrochemical degradation of alizarin yellow R (AYR) wastewater. The test results of X-ray diffraction, field-emission scanning electron microscopy and energy-dispersive X-ray spectroscopy confirm that Sm₂O₃ is successfully composited with PbO₂. The coating of Ti/PbO₂-Sm₂O₃ composite electrode stacked by typical pyramid-like micro-particles exhibits smooth and compact surface morphology which is conducive to enhancing the corrosion resistance of electrode. Furthermore, electrochemical performance tests indicate that Ti/PbO₂-Sm₂O₃ composite electrode has advantages of higher oxygen evolution potential, lower charge transfer resistance and longer lifetime over Ti/PbO₂ electrode. Electrolyte concentration, plate space, initial pH and cell voltage are assessed to optimize the degradation condition of AYR. The results show that COD removal efficiency and degradation efficiency of AYR on Ti/PbO₂-Sm₂O₃ composite electrode reach up to 79.90% and 80.00% under the optimal conditions (Na₂SO₄ electrolyte concentration 9.0 g L^-1, plate space 3.0 cm, initial pH 5, cell voltage 3.0 V and electrolysis time 150 min), respectively. The degradation of AYR follows pseudo-first-order reaction kinetics, and a plausible mineralization pathway of AYR is proposed on the basis of the identification of major intermediate products. These results suggest that Ti/PbO₂-Sm₂O₃ composite electrode is a promising candidate for electrocatalytic degradation of AYR wastewater.