Adsorption and release of ampicillin antibiotic from ordered mesoporous silica

Preparation and characterization of biochar from four different solid wastes and its ampicillin adsorption performance

The integration of biochar (BC) production from organic waste with ampicillin (AMP), an emerging pollutant, adsorption is a novel and promising treatment approach. In this study, peanut shells, coffee grounds, digestates, and oyster shells were used for BC production. Among these, the use of anaerobic digestate from food waste fermentation to produce extracts for antibiotic adsorption is relatively unexplored. The pyrolysis temperature was determined using thermogravimetric analysis (TGA) and the materials were characterized with BET, SEM, FTIR, and XRD. The TGA results indicate that PSB, CRB, and DSB underwent pyrolysis involving cellulose, hemicellulose, and lignin, whereas OSB underwent crystal formation. Characterization revealed that DSB has more functional groups, a superior mesoporous structure, appropriate O/C ratio, and trace amounts of calcite crystals, which are favorable for AMP adsorption. Adsorption experiments demonstrate that all four materials adhere to the Freundlich and Langmuir isotherm and Elovich kinetic models, indicating predominant physical adsorption, with some chemical adsorption also present. Thermodynamic studies demonstrate that BC is spontaneous during adsorption and is a heat-absorbing reaction. DSB exhibits the strongest AMP adsorption. A 53.81 mg g-1 adsorbance was obtained at a dosage of 150 mg, pH = 2, and 60 °C. This study introduces innovative approaches for managing waste types and provides data to support the selection of suitable solid wastes for the preparation of BC with excellent adsorption properties. Furthermore, it lays the groundwork for future studies aimed at enhancing the AMP treatment efficacy.

Enhancing the antibacterial activity of ampicillin loaded into chitosan/starch nanocomposites against AMR Staphylococcusaureus

Ampicillin (Amp), an antibiotic, is widely used to treat bacterial infections in humans and livestock, but recently the rate of resistance has increased rapidly. The aim of this work was to enhancing the antibacterial effect of this compound against AMR Staphylococcus aureus via loading Amp into chitosan/starch nanocomposites by spray drying technique. The results showed that the different ratio of chitosan gel and starch gel used in preparing the nanocomposites can affect its properties and performance. The size distribution of the nanocomposite particles was ranging from 122.0 to 816.9 nm. The zeta potential values of the nanocomposites range from +29.47 to +93.07 mV, indicating the stability of the particles and their tendency to repel each other. Ampicillin was loaded into the chitosan/starch nanocomposites with encapsulation efficiency of 70.7-77.3 %, then their releasing and antibacterial effect against AMR S. aureus were investigated. The results indicated that antibacterial activity of chitosan/starch nanocomposites loaded ampicillin was much higher than ampicillin alone. Chitosan/starch nanocomposites loaded ampicillin at concentration 5.0 μg/mL inhibited 88.6 % growth of S. aureus to a similar extent as 7.5 μg/mL of ampicillin alone. Additionally, at same 7.5 μg/mL ampicillin concentration, the nanocomposites loaded ampicillin showed a higher inhibitory rate (93.27 %) compared to ampicillin alone (88.96 %) over a 12 h-period. Especially, the antibacterial activity of chitosan/starch nanocomposites loaded ampicillin still maintained their effectiveness over 48 h (95.43 %) while those the ampicillin decreased down to 85.76 %. This research highlights the potential of using the chitosan/starch nanocomposites as nanocarriers for ampicillin to enhance its antibacterial activity against AMR Staphylococcus aureus. This approach could be a promising strategy to combat antimicrobial resistance.

Specific buffer effects on the formation of BSA protein corona around amino-functionalized mesoporous silica nanoparticles

The effect of buffer species on biomolecules and biomolecule-nanoparticle interactions is a phenomenon that has been either neglected, or not understood. Here, we study the formation of a BSA protein corona (PC) around amino-functionalized mesoporous silica nanoparticles (MSN-NH2) in the presence of different buffers (Tris, BES, cacodylate, phosphate, and citrate) at the same pH (7.15) and different concentrations (10, 50, and 100 mM). We find that BSA adsorption is buffer specific, with the adsorbed amount of BSA being 4.4 times higher in the presence of 100 mM Tris (184 ± 3 mg/g) than for 100 mM citrate (42 ± 2 mg/g). That is a considerable difference that cannot be explained by conventional theories. The results become clearer if the interaction energies between BSA and MSN-NH2, considering the electric double layer (EEDL) and the van der Waals (EvdW) terms, are evaluated. The buffer specific PC derives from buffer specific zeta potentials that, for MSN-NH2, are positive with Tris and negative with citrate buffers. A reversed sign of zeta potentials can be obtained by considering polarizability-dependent dispersion forces acting together with electrostatics to give the buffer specific outcome. These results are relevant not only to our understanding of the formation of the PC but may also apply to other bio- and nanosystems in biological media.

Mesoporous silica nanospheres-mediated insecticide and antibiotics co-delivery system for synergizing insecticidal toxicity and reducing environmental risk of insecticide

Mesoporous silica nanoparticles (MSNs) are efficient carriers of drugs, and are promising in developing novel pesticide formulations. The cotton aphids Aphis gossypii Glover is a world devastating insect pest. It has evolved high level resistance to various insecticides thus resulted in the application of higher doses of insecticides, which raised environmental risk. In this study, the MSNs based pesticide/antibiotic delivery system was constructed for co-delivery of ampicillin (Amp) and imidacloprid (IMI). The IMI@Amp@MSNs complexes have improved toxicity against cotton aphids, and reduced acute toxicity to zebrafish. From the 16S rDNA sequencing results, Amp@MSNs, prepared by loading ampicillin to the mesoporous of MSNs, greatly disturbed the gut community of cotton aphids. Then, the relative expression of at least 25 cytochrome P450 genes of A. gossypii was significantly suppressed, including CYP6CY19 and CYP6CY22, which were found to be associated with imidacloprid resistance by RNAi. The bioassay results indicated that the synergy ratio of ampicillin to imidacloprid was 1.6, while Amp@MSNs improved the toxicity of imidacloprid by 2.4-fold. In addition, IMI@Amp@MSNs significantly improved the penetration of imidacloprid, and contributed to the amount of imidacloprid delivered to A. gossypii increased 1.4-fold. Thus, through inhibiting the relative expression of cytochrome P450 genes and improving penetration of imidacloprid, the toxicity of IMI@Amp@MSNs was 6.0-fold higher than that of imidacloprid. The greenhouse experiments further demonstrated the enhanced insecticidal activity of IMI@Amp@MSNs to A. gossypii. Meanwhile, the LC50 of IMI@Amp@MSNs to zebrafish was 3.9-fold higher than that of IMI, and the EC50 for malformation was 2.8-fold higher than IMI, respectively, which indicated that the IMI@Amp@MSNs complexes significantly reduced the environmental risk of imidacloprid. These findings encouraged the development of pesticide/antibiotic co-delivery nanoparticles, which would benefit pesticide reduction and environmental safety.

Hydrophilic and hydrophobic drug release from core (polyvinylpyrrolidone)-sheath (ethyl cellulose) pressure-spun fibers

A core-sheath structure is one of the methods developed to overcome the challenges often faced when using monolithic fibers for drug delivery. In this study, fibers based on polyvinylpyrrolidone (core) and ethyl cellulose (sheath) were successfully produced using a novel core-sheath pressure-spinning process. For comparison, these two polymers were also processed into as blend fibers. All samples were then investigated for their performances in releasing water-soluble ampicillin (AMP) and poorly water-soluble ibuprofen (IBU) model drugs. Scanning electron,digital and confocal microscopy confirmed that fibers with a core-sheath structure were successfully made. Fourier transform infrared spectroscopy showed the success of the pressure-spinning technique in encapsulating AMP/IBU in all fiber samples. Compared to blend fibers, the core-sheath fibers had better performance in encapsulating both water-soluble and poorly water-soluble drugs. Moreover, the core-sheath structure was able to reduce the initial burst release and provided a better sustained release profile than the blend fiber analog. In conclusion, the pressure-spinning method was capable of producing core-sheath and blend fibers that could be used for the loading of either hydrophilic or hydrophobic drugs for controlled drug delivery systems.

Insights on the Synthesis of Al-MCM-41 with Optimized Si/Al Ratio for High-Performance Antibiotic Adsorption

Studies indicate that approximately two-thirds of the rivers of the world are contaminated by pharmaceutical compounds, especially antibiotics and hormones. Data reported by the World Health Organization (WHO, 2015) revealed an increase of 65% in antibiotic consumption between 2000 and 2015, with a worldwide increase of 200% expected up to 2030. Environmental contamination by antibiotics and their metabolites can cause the alteration of bacterial genes, leading to the generation of superbacteria. In this work, adsorption was explored as a strategy to mitigate antibiotic contamination, proposing the use of the Al-MCM-41 mesoporous material as an efficient and high-capacity adsorbent. Evaluation of the influence of the synthesis parameters enabled understanding of the main variables affecting the adsorption capacity of Al-MCM-41 for the removal of a typical antibiotic, amoxicillin (AMX). It was found that the adsorbent composition and specific surface area were the main factors that should be optimized in order to obtain the highest AMX removal capacity. Using statistical tools, the best Si/Al ratio in Al-MCM-41 was found to be 10.5, providing an excellent AMX uptake of 132.2 mg per gram of adsorbent. The Si/Al ratio was the most significant factor affecting the adsorption. The cation-π interactions increased with an increase of the Al content, while the interactions involving silanols (Yoshida H-bonding and dipole-dipole hydrogen bridges) decreased.

Molecular-scale insights into confined clindamycin in nanoscale pores of mesoporous silica

Clindamycin is an antibiotic used to treat a variety of bacterial infections. The sustained release of clindamycin from the drug carrier is an important strategy to prolong the effective antibacterial duration. In this work, the microstructure and dynamics of clindamycin confined into the nanopores of mesopore silica with different pore sizes were studied using molecular dynamics simulation. It is found that there is a layering behavior for clindamycin distribution as a function of distance from the pore surface to the pore center with preferred location near the surface of the nanopore. The radial distribution function between carbonyl oxygen and the silanol groups shows the highest intensity of the first peak with the preferred orientation of carbonyl oxygen pointing toward the pore surface, which suggests the strong interaction between the carbonyl oxygen and the silanol groups on the pore surface. The higher local diffusion coefficients for the clindamycin molecules near the pore surface can be found. In addition, the presence of water can lead to the shift of clindamycin distribution away from the surface and promote the local diffusion of clindamycin near the pore surface. The information in this work will provide the microscopic understanding for the design of the drug carriers for the controlled release of clindamycin.

Intestinal Villi-Inspired Mathematically Base-Layer Engineered Microneedles (IMBEMs) for Effective Molecular Exchange during Biomarker Enrichment and Drug Deposition in Diversified Mucosa

The mucosa-interfacing systems based on bioinspired engineering design for sampling/drug delivery have manifested crucial potential for the monitoring of infectious diseases and the treatment of mucosa-related diseases. However, their efficiency and validity are severely restricted by limited contact area for molecular transfer and dissatisfactory capture/detachment capability. Herein, inspired by the multilayer villus structure of the small intestine that enables high nutrient absorption, a trigonometric function-based periodic pattern was fabricated and integrated on the base layer of the microneedle patch, exhibiting a desirable synergistic effect with needle tips for deep sample enrichment and promising molecular transfer, significantly improving the device-mucosa bidirectional interaction. Moreover, mathematical modeling and finite element analysis were adopted to visualize and quantify the microcosmic molecular transmission process, guiding parameter optimization in actual situation. Encouragingly, these intestinal villi-inspired mathematically base-layer engineered microneedles (IMBEMs) have demonstrated distinguished applicability among mucosa tissue with varying surface curvatures, tissue toughness, and local environments, and simultaneously, have gained favorable support from healthy volunteers receiving preliminary test of IMBEMs patches. Overall, validated by numerous in vitro and in vivo tests, the IMBEMs were confirmed to act as a promising candidate to facilitate mucosa-based sampling and topical drug delivery, indicating highly clinical translation potential.

Effect of molecular structure on the adsorption behavior of sulfanilamide antibiotics on crumpled graphene balls

Since the 1930s, sulfonamide(SA)-based antibiotics have served as important pharmaceuticals, but their widespread detection in water systems threatens aquatic organisms and human health. Adsorption via graphene, its modified form (graphene oxide, GO), and related nanocomposites is a promising method to remove SAs, owing to the strong and selective surface affinity of graphene/GO with aromatic compounds. However, a deeper understanding of the mechanisms of interaction between the chemical structure of SAs and the GO surface is required to predict the performance of GO-based nanostructured materials to adsorb the individual chemicals making up this large class of pharmaceuticals. In this research, we studied the adsorptive performance of 3D crumpled graphene balls (CGBs) to remove 10 SAs and 13 structural analogs from water. The maximum adsorption capacity qm of SAs on CGB increased with the number of (1) aromatic rings; (2) electron-donating functional groups; (3) hydrogen bonding acceptor sites. Furthermore, the CGB surface displayed a preference for homocyclic relative to heterocyclic aromatic structures. A leading mechanism, π-π electron-donor-acceptor interaction, combined with hydrogen bonding, explains these trends. We developed a multiple linear regression model capable of predicting the qm as a function of SA chemical structure and properties and the oxidation level of CGB. The model predicted the adsorptive behaviors of SAs well with the exception of a chlorinated/fluorinated SA. The insights afforded by these experiments and modeling will aid in tailoring graphene-based adsorbents to remove micropollutants from water and reduce the growing public health threats associated with antibiotic resistance and endocrine-disrupting chemicals.

Multimodal-Driven Magnetic Microrobots with Enhanced Bactericidal Activity for Biofilm Eradication and Removal from Titanium Mesh

Modern micro/nanorobots can perform multiple tasks for biomedical and environmental applications. Particularly, magnetic microrobots can be completely controlled by a rotating magnetic field and their motion powered and controlled without the use of toxic fuels, which makes them most promising for biomedical application. Moreover, they are able to form swarms, allowing them to perform specific tasks at a larger scale than a single microrobot. In this work, they developed magnetic microrobots composed of halloysite nanotubes as backbone and iron oxide (Fe₃ O₄ ) nanoparticles as magnetic material allowing magnetic propulsion and covered these with polyethylenimine to load ampicillin and prevent the microrobots from disassembling. These microrobots exhibit multimodal motion as single robots as well as in swarms. In addition, they can transform from tumbling to spinning motion and vice-versa, and when in swarm mode they can change their motion from vortex to ribbon and back again. Finally, the vortex motion mode is used to penetrate and disrupt the extracellular matrix of Staphylococcus aureus biofilm colonized on titanium mesh used for bone restoration, which improves the effect of the antibiotic's activity. Such magnetic microrobots for biofilm removal from medical implants could reduce implant rejection and improve patients' well-being.

Endogenous NO-release multi-responsive hollow mesoporous silica nanoparticles for drug encapsulation and delivery

Novel multi-responsive drug delivery vehicles (CDs/PNVCL@HMSNs) were prepared by grafting amino-terminated poly (N-vinyl caprolactam) (PNVCL-NH₂) and amino-rich carbon dots (CDs) on the surface of aldehyde-functionalized HMSNs (HMSNs-CHO) via Schiff base reaction. The CDs were prepared from L-arginine and their surfaces were rich in guanidine. Doxorubicin (DOX) was loaded into the nanoparticles to form drug loaded vehicles (CDs/PNVCL@HMSNs-DOX) and the drug loading efficiency was 58.38%. The drug release behaviors of CDs/PNVCL@HMSNs-DOX showed temperature and pH responsiveness due to the poly (N-vinyl caprolactam) (PNVCL) and Schiff base bond. The high concentration of NO released in high concentration H₂O₂ of tumor site could induce tumor cells apoptosis. The multi-responsive CDs/PNVCL@HMSNs are intriguing drug carriers, which combine drug delivery and NO release in one.

Virus Inactivation Based on Optimal Surfactant Reservoir of Mesoporous Silica

SARS-CoV-2 (severe acute respiratory syndrome coronavirus 2) caused a pandemic in 2019 and reaffirmed the importance of environmental sanitation. To prevent the spread of viral infections, we propose the application of a mesoporous silica (MS)-based virus-inactivating material. MS is typically synthesized using a micellar surfactant template; hence, the intermediate before removal of the surfactant template is expected to have a virus-inactivating activity. MS-CTAC particles filled with cetyltrimethylammonium chloride (CTAC), a cationic surfactant with an alkyl chain length of 16, were used to test this hypothesis. Plaque assays revealed that the MS-CTAC particles inactivated the enveloped bacteriophage φ6 by approximately 4 orders of magnitude after a contact time of 10 min. The particles also indicated a similar inactivation effect on the nonenveloped bacteriophage Qβ. In aqueous solution, CTAC loaded on MS-CTAC was released until the equilibrium concentration of loading and release on MS was reached. The released CTAC acted on viruses. Thus, MS is likely a good reservoir for the micellar surfactant. Surfactant readsorption also occurred in the MS particles, and the highest retention rate was observed when micellar surfactants with alkyl chain lengths appropriate for the pore size were used. The paper containing MS-CTAC particles was shown to maintain stable viral inactivation for at least three months in a typical indoor environment. Applying this concept to indoor wallpaper and air-conditioning filters could contribute to the inactivation of viruses in aerosols. These findings open possibilities for mesoporous materials with high surface areas, which can further develop into virus inactivation materials.

Various hydrogen bonds make different fates of pharmaceutical contaminants on oxygen-rich nanomaterials

Various hydrogen bonds, especially charge-assisted hydrogen bond (CAHB), is considered as one of vital mechanisms affecting the environmental behavior and risk of pharmaceutical contaminants (PCs). Herein the sorption/desorption of three PCs including clofibric acid (CA), acetaminophen (ACT), and sulfamerazine (SMZ) on three Oxygen-rich (O-rich) nanoparticles (nano-silica: Nano-SiO₂, nano-alumina: Nano-Al₂O₃, and oxidized carbon nanotubes: O-CNTs) were investigated to explore the effect of various hydrogen bonds with different strengths on environmental behaviors of PCs. The results indicated that although solvent-assisted CAHB, solvent-uninvolved CAHB, and ordinary hydrogen bond (OHB) all played a crucial role in sorption of PCs on three O-rich nanomaterials, they showed significantly different effects on the desorption behaviors of PCs from three sorbents. Compared with OHB (hysteresis index ≤0.0766), the stronger CAHB (hysteresis index ≥0.1981) between PCs and O-rich nanoparticles having comparable pK_a with PCs, caused obvious desorption hysteresis of PCs, resulting in their better immobilization on O-rich nanomaterials. The FTIR characterization found that both solvent-assisted and solvent-uninvolved CAHB formation resulted in a new characteristic peak appeared in the high frequency (3660 cm^-1 for Nano-SiO₂, 3730 cm^-1 for Nano-Al₂O₃, and 3780 cm^-1 for O-CNTs). Also, density functional theory (DFT) calculation verified that the smaller |ΔpK_a| between PCs and O-rich sorbents, the shorter bond length, and the larger bond angle resulted in the stronger hydrogen bond formed, thereby leading to the greater immobilization of PCs. These results provide in-depth understanding of the environmental behavior and risk of PCs, and light new idea for designed materials to control PCs pollution in the environment.

Mesoporous silica SBA-15 composite for the delivery of amoxicillin against S. aureus skin infection

By subcutaneous injection of an amoxicillin-loaded nanocomposite, the skin bacterial infection of mice was well alleviated, and wound recovery was improved.

Stimuli-responsive nanoparticle-nanofiber hybrids for drug delivery and photodynamic therapy

Hybrid nanomaterials possess integrated multi-components to syncretize various properties and functions within a single entity. Owing to this synergistic effect, they promise efficient anti-cancer therapy. In line with this target, we produced stimuli-responsive nanoparticle-nanofiber hybrids (NNHs) via embedding photoresponsive natural melanin nanoparticles (MNPs) within a biocompatible polycaprolactone (PCL) nanofiber matrix. Electrospinning was performed to produce monolithic and core-shell structured NNHs using a single and a coaxial nozzle. The NNHs were upgraded to drug delivery systems by model hydrophilic drug-ampicillin (amp)-loading. The drug release results showed that monolithic PCL meshes displayed a burst release, whereas nanohybrid formation with MNPs improved the release profile toward Fickian diffusion. Core-shell NNH presented a more sustained drug release profile than its MNP-free replica and monolithic NNH because its encapsulating shell layer hindered the diffusion of the drug. The photodynamic therapy accompanied by UV-A-irradiation on monolithic and core-shell NNHs yielded up to 34 % and 37 % malignant melanoma cell death. Moreover, this study proved the potency of MNPs-enhanced NNHs in drug delivery and photodynamic therapy applications. Even so, more efforts should be concerted to unlock unknown features of the NNHs, which have the power to advance emerging areas, including but not limited to material science, biosensing, and theranostics.

Nanoplatforms for Irinotecan Delivery Based on Mesoporous Silica Modified with a Natural Polysaccharide

Natural compounds are an important source of beneficial components that could be used in cancer therapy along with well-known cytostatic agents to enhance the therapeutic effect while targeting tumoral tissues. Therefore, nanoplatforms containing mesoporous silica and a natural polysaccharide, ulvan, extracted from Ulva Lactuca seaweed, were developed for irinotecan. Either mesoporous silica-ulvan nanoplatforms or irinotecan-loaded materials were structurally and morphologically characterized. In vitro drug release experiments in phosphate buffer solution with a pH of 7.6 emphasized the complete recovery of irinotecan in 8 h. Slower kinetics were obtained for the nanoplatforms with a higher amount of natural polysaccharide. Ulvan extract proved to be biocompatible up to 2 mg/mL on fibroblasts L929 cell line. The irinotecan-loaded nanoplatforms exhibited better anticancer activity than that of the drug alone on human colorectal adenocarcinoma cells (HT-29), reducing their viability to 60% after 24 h. Moreover, the cell cycle analysis proved that the irinotecan loading onto developed nanoplatforms caused an increase in the cell number trapped at G0/G1 phase and influenced the development of the tumoral cells.

Au/Ti Synergistically Modified Supports Based on SiO2 with Different Pore Geometries and Architectures

New photocatalysts were obtained by immobilization of titanium and gold species on zeolite Y, hierarchical zeolite Y, MCM-48 and KIT-6 supports with microporous, hierarchical and mesoporous cubic structure. The obtained samples were characterized by X-ray diffraction (XRD), N2-physisorption, scanning and transmission electron microscopy (SEM/TEM), diffuse reflectance UV–Vis spectroscopy (DRUV-Vis), X-ray photoelectron spectroscopy (XPS), Raman and photoluminescence spectroscopy. The photocatalytic properties were evaluated in degradation of amoxicillin (AMX) from water, under UV (254 nm) and visible light (532 nm) irradiation. The higher degradation efficiency and best apparent rate constant were obtained under UV irradiation for Au-TiO2-KIT-6, while in the visible condition for the Au-TiO2-MCM-48 sample containing anatase, rutile and the greatest percent of Au metallic clusters were found (evidenced by XPS). Although significant values of amoxicillin degradation were obtained, total mineralization was not achieved. These results were explained by different reaction mechanisms, in which Au species act as e− trap in UV and e− generator in visible light.

Use of Photocatalytically Active Supramolecular Organic–Inorganic Magnetic Composites as Efficient Route to Remove β-Lactam Antibiotics from Water

Considerable efforts have been made in recent years to identify an optimal treatment method for the removal of antibiotics from wastewaters. A series of supramolecular organic-inorganic magnetic composites containing Zn-modified MgAl LDHs and Cu-phthalocyanine as photosensitizers were prepared with the aim of removing β-lactam antibiotics from aqueous solutions. The characterization of these materials confirmed the anchorage of Cu-phthalocyanine onto the edges of the LDH lamellae, with a negligible part inserted in the interlayer space. The removal of the β-lactam antibiotics occurred via concerted adsorption and photocatalytic degradation. The efficiency of the composites depended on (i) the LDH: magnetic nanoparticle (MP) ratio, which was strongly correlated with the textural properties of the catalysts, and (ii) the phthalocyanine loading in the final composite. The maximum efficiency was achieved with a removal of ~93% of the antibiotics after 2 h of reaction.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.

Evaluation of efficiency and capacity of thermal, chemical and ultrasonic regeneration of tetracycline exhausted activated carbon

Emerging pollutants have received increasing attention because of their potential environmental risks. As conventional treatment processes are not able to completely remove emerging pollutants, such as drugs, for example, the adsorption process is considered a complementary treatment. However, after some time of use, the adsorbent solids used in this type of process become saturated and there may be a higher demand for replacement of these materials, resulting in a large amount of solid waste. In this context, the objective of this study was to evaluate regeneration techniques of adsorbent solid depleted with emerging tetracycline pollutant. For this, tests were performed using three regenerative methods - thermal, chemical and ultrasonic, where through them were analyzed the influence of temperature, type of solvent and sonification time, respectively. Virgin, saturated and regenerated solids were characterized by their physical structure, micro and mesopore distribution and scanning electron microscopy. For all techniques employed, the regeneration efficiency reached values ⁣⁣above 85%. Thermal treatments at 200°C, 100% methanol solution, 100% deionized water with 60 °C heating and ultrasonic treatment at 5 and 20 minutes were chosen as the most viable methods for the study of adsorption/desorption cycles. Compared to the others, the heat treatment at 200°C remained with consistent results until the sixth cycle, presenting a regenerative capacity of 90%. Therefore, it has been selected as the most suitable regenerative agent, ensuring that CAG can be regenerated and used repeatedly in the treatment of tetracycline contaminated waters.

APTES-Modified SBA-15 as a Non-Toxic Carrier for Phenylbutazone

Improvement of the bioavailability of poorly soluble medicinal substances is currently one of the major challenges for pharmaceutical industry. Enhancing the dissolution rate of those drugs using novel methods allows to increase their bioavailability. In recent years, silica-based mesoporous materials have been proposed as drug delivery systems that augment the dissolution rate. The aim of this study was to analyse the influence of phenylbutazone adsorption on SBA-15 on its dissolution rate. Moreover, we examined the cytotoxicity of the analyzed silica. The material was characterized by SEM, TEM, DSC, ¹H-NMR, XRD, and FT-IR. The phenylbutazone did not adsorb on unmodified SBA-15, while the adsorption on APTES-modified SBA-15 resulted in 50.43 mg/g of loaded phenylbutazone. Phenylbutazone adsorbed on the APTES-modified SBA-15 was then released in the hydrochloric acidic medium (pH 1.2) and phosphate buffer (pH 7.4) and compared to the dissolution rate of the crystalline phenylbutazone. The release profiles of the amorphous form of adsorbed phenylbutazone are constant in different pH, while the dissolution rate of the crystalline phenylbutazone depends on the pH. The cytotoxicity assays were performed using the Caco-2 cell line. Our results indicate that the analyzed material ensured phenylbutazone adsorption in an amorphous state inside the mesopores and increased its dissolution rate in various pH levels. Furthermore, the cytotoxicity assay proved safety of studied material. Our study demonstrated that APTES-modified SBA-15 can serve as a non-toxic drug carrier that improves the bioavailability of phenylbutazone.

Obtention of biochar-Fe/Ce using Punica granatum with high adsorption of ampicillin capacity

This research presents the obtaining of a biochar (CB) from the use of pomegranate peel (Punica granatum) conditioned with iron and cerium nanoparticles (C-Fe/Ce), as well as its characterization by SEM (Scanning Electronic Microscopy), FTIR (Fourier Transform Infrared Spectrometry), TGA (Thermogravimetric analysis), EDS (Energy Dispersive Spectroscopy), XPS (X-Ray Photoelectron Spectroscopy) and evaluation of the adsorption capacity of ampicillin (AMP) in aqueous phase at 20, 30 and 40 °C. The maximum adsorption capacity for CB was 18.97 mg g-1 and for C-Fe/Ce, 27.61 mg g-1 at pH of 7, observing that with increasing temperature, the sorption capacity decreases in both materials, the experimental data was fitted to various mathematical models and the best fit was the pseudo-second order model for the kinetics, whilst for the adsorption isotherms the best fit was with the Langmuir model, indicating that the adsorption process is carried out in a monolayer on a homogeneous surface, through a chemisorption process. According to the thermodynamic parameters this process is carried out through an exothermic reaction. The results obtained indicate that both materials are suitable for the removal of AMP in the aqueous phase and that they can be reused up to 5 times.

Thermally-treated MgO/nanocrystalline cellulose immobilized onto a Santa Barbara-16 mesoporous SiO2 template for the sequestration of antibiotics from polluted water

Clean technologies using functional materials as adsorbents for removing antibiotics from polluted water are of great interest, especially for water scarce sub-African countries.

Activated carbon derived from Azolla filiculoides fern: a high-adsorption-capacity adsorbent for residual ampicillin in pharmaceutical wastewater

In this study, the effectiveness of activated carbon prepared from the Azolla filiculoides fern (ACAF) in order to remove ampicillin from aqueous solution was examined. The preparation of the ACAF was performed through chemical and physical activation processes with the presence of ZnCl2 and at a temperature of 450 °C. The ACAF yield was 44.7% of the fresh Azolla filiculoides. The results obtained from the characterization study indicate that the prepared ACAF has excellent surface and internal properties to be used as an adsorbent. The surface area, porosity, and pore volume were estimated to be 716.4 m2/g, 51.2%, and 0.621 cm3/g, respectively. The functional groups in ACAF that were responsible for the adsorption of ampicillin molecules were detected using FTIR analyses. The maximum efficiency (96.84%) and uptake (114.3 mg/g) of ACAF to remove ampicillin were achieved under the following conditions: ACAF dose = 0.8 g/L, pH = 7, concentration of ampicillin = 100 mg/L, contact time = 60 min, and temperature = 45 °C. It was found that the kinetic and isotherm data matched the pseudo-second-order and Langmuir models with high precision values, respectively. Considering the thermodynamics of the adsorption, the endothermic and spontaneous nature of the ampicillin adsorption onto ACAF was approved. The ampicillin adsorption capacity by ACAF was not significantly affected by the presence of different concentrations of NaNO3 competitor ion. The considerably higher adsorption capacity of the ACAF for ampicillin (114.3 mg/g) than other previously used adsorbents with excellent regeneration level (five cycles) depicts the superior performance of ACAF in the adsorption systems.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s13399-021-01962-4.

Response surface methodology optimizing the adsorptive removal of azithromycin using mesoporous silica SBA-15: Mechanism, thermodynamic, equilibrium, and kinetics modeling studies

The objective of this research was to study an effective adsorbent for removing azithromycin (AZT) from industrial wastewater. AZT is an antibiotic used for many diseases remedy, but it is a pollutant to our environment; therefore, its residual should be removed from wastewater. The mesoporous SBA-15 silica as an efficient adsorbent was prepared by the hydrothermal method. The surface of mesoporous SBA-15 plays a significant role in the removal process; therefore, the characterization of the adsorbent was accomplished by several techniques. The batch system has been used, and the effect of four essential variables: pH (3-10), drug concentration (20-200 mg L^-1), sorbent weight (0.2-2 g L^-1), and temperature (20-40 °C) were investigated on the AZT removal efficiency by response surface methodology (RSM). The isotherm results were found to be in proper compliance with the isotherm model of Freundlich. In the kinetics part of this study, the experimental outcomes were fitted to the equation model of pseudo-second-order. The calculation of thermodynamic parameters shows that the removal process is spontaneous and endothermic. Upon the results, the vast surface area, the active functional groups, reusability, stability, and inexpensively make the mesoporous SBA-15 a suitable candidate for removal of AZT and similar antibiotics.

Fabrication of pH-responsive nanoparticles for high efficiency pyraclostrobin delivery and reducing environmental impact

In this work, a pH-responsive pesticide delivery system using mesoporous silica nanoparticles (MSNs) as the porous carriers and coordination complexes of Cu ions and tannic acid (TA-Cu) as the capping agent was established for controlling pyraclostrobin (PYR) release. The results showed the loading capacity of PYR@MSNs-TA-Cu nanoparticles for pyraclostrobin was 15.7 ± 0.5% and the TA-Cu complexes deposited on the MSNs surface could protect pyraclostrobin against photodegradation effectively. The nanoparticles had excellent pH responsive release performance due to the decomposition of TA-Cu complexes under the acid condition, which showed 8.53 ± 0.37%, 82.38 ± 1.67% of the encapsulated pyraclostrobin were released at pH 7.4, pH 4.5 after 7 d respectively. The contact angle and adhesion work of PYR@MSNs-TA-Cu nanoparticles on rice foliage were 86.3° ± 2.7° and 75.8 ± 3.1 mJ/m² after 360 s respectively, indicating that TA on the surface of the nanoparticles could improve deposition efficiency and adhesion ability on crop foliage. The control effect of PYR@MSNs-TA-Cu nanoparticles against Rhizoctonia solani with 400 mg/L of pyraclostrobin was 85.82% after 7 d, while that of the same concentration of pyraclostrobin EC was 53.05%. The PYR@MSNs-TA-Cu nanoparticles did not show any phytotoxicity to the growth of rice plants. Meanwhile, the acute toxicity of PYR@MSNs-TA-Cu nanoparticles to zebrafish was decreased more than 9-fold compared with that of pyraclostrobin EC. Thus, pH-responsive PYR@MSNs-TA-Cu nanoparticles have great potential for enhancing targeting and environmental safety of the active ingredient.

Adsorption and Release of Sulfamethizole from Mesoporous Silica Nanoparticles Functionalised with Triethylenetetramine

Mesoporous silica nanoparticles (MSN) were synthesised and functionalised with triethylenetetramine (MSN-TETA). The samples were fully characterised (transmission electron microscopy, small angle X-ray scattering, Fourier transform infrared spectroscopy, thermogravimetric analysis, zeta potential and nitrogen adsorption/desorption isotherms) and used as carriers for the adsorption of the antimicrobial drug sulphamethizole (SMZ). SMZ loading, quantified by UV-Vis spectroscopy, was higher on MSN-TETA (345.8 mg g-1) compared with bare MSN (215.4 mg g-1) even in the presence of a lower surface area (671 vs. 942 m2 g-1). The kinetics of SMZ adsorption on MSN and MSN-TETA followed a pseudo-second-order model. The adsorption isotherm is described better by a Langmuir model rather than a Temkin or Freundlich model. Release kinetics showed a burst release of SMZ from bare MSN samples (k1 = 136 h-1) in contrast to a slower release found with MSN-TETA (k1 = 3.04 h-1), suggesting attractive intermolecular interactions slow down SMZ release from MSN-TETA. In summary, the MSN surface area did not influence SMZ adsorption and release. On the contrary, the design of an effective drug delivery system must consider the intermolecular interactions between the adsorbent and the adsorbate.

Recent Advances Toward the Use of Mesoporous Silica Nanoparticles for the Treatment of Bacterial Infections

It is a fact that the use of antibiotics is inducing a growing resistance on bacteria. This situation is not only the consequence of a drugs’ misuse, but a direct consequence of a widespread and continuous use. Current studies suggest that this effect could be reversed by using abandoned antibiotics to which bacteria have lost their resistance, but this is only a temporary solution that in near future would lead to new resistance problems. Fortunately, current nanotechnology offers a new life for old and new antibiotics, which could have significantly different pharmacokinetics when properly delivered; enabling new routes able to bypass acquired resistances. In this contribution, we will focus on the use of porous silica nanoparticles as functional carriers for the delivery of antibiotics and biocides in combination with additional features like membrane sensitizing and heavy metal-driven metabolic-disrupting therapies as two of the most interesting combination therapies.

Lactose-Gated Mesoporous Silica Particles for Intestinal Controlled Delivery of Essential Oil Components: An In Vitro and In Vivo Study

Mesoporous silica microparticles functionalized with lactose for the specific release of essential oil components (EOCs) in the small intestine are presented. In vitro and in vivo intestinal models were applied to validate the microparticles (M41-EOC-L), in which the presence of lactase acts as the triggering stimulus for the controlled release of EOCs. Among the different microdevices prepared (containing thymol, eugenol and cinnamaldehyde), the one loaded with cinnamaldehyde showed the most significant Caco-2 cell viability reduction. On the other hand, interaction of the particles with enterocyte-like monolayers showed a reduction of EOCs permeability when protected into the designed microdevices. Then, a microdevice loaded with cinnamaldehyde was applied in the in vivo model of Wistar rat. The results showed a reduction in cinnamaldehyde plasma levels and an increase in its concentration in the lumen of the gastrointestinal tract (GIT). The absence of payload release in the stomach, the progressive release throughout the intestine and the prolonged stay of the payload in the GIT-lumen increased the bioavailability of the encapsulated compound at the site of the desired action. These innovative results, based on the specific intestinal controlled delivery, suggest that the M41-payload-L could be a potential hybrid microdevice for the protection and administration of bioactive molecules in the small intestine and colon.

Lipid-Polymer Hybrid Nanoparticles Enhance the Potency of Ampicillin against Enterococcus faecalis in a Protozoa Infection Model

Enterococcus faecalis (E. faecalis) biofilms are implicated in endocarditis, urinary tract infections, and biliary tract infections. Coupled with E. faecalis internalization into host cells, this opportunistic pathogen poses great challenges to conventional antibiotic therapy. The inability of ampicillin (Amp) to eradicate bacteria hidden in biofilms and intracellular niches greatly reduces its efficacy against complicated E. faecalis infections. To enhance the potency of Amp against different forms of E. faecalis infections, Amp was loaded into Lipid-Polymer hybrid Nanoparticles (LPNs), a highly efficient nano delivery platform consisting of a unique combination of DOTAP lipid shell and PLGA polymeric core. The antibacterial activity of these nanoparticles (Amp-LPNs) was investigated in a protozoa infection model, achieving a much higher multiplicity of infection (MOI) compared with studies using animal phagocytes. A significant reduction of total E. faecalis was observed in all groups receiving 250 μg/mL Amp-LPNs compared with groups receiving the same concentration of free Amp during three different interventions, simulating acute and chronic infections and prophylaxis. In early intervention, no viable E. faecalis was observed after 3 h LPNs treatment whereas free Amp did not clear E. faecalis after 24 h treatment. Amp-LPNs also greatly enhanced the antibacterial activity of Amp at late intervention and boosted the survival rate of protozoa approaching 400%, where no viable protozoa were identified in the free Amp groups at the 40 h postinfection treatment time point. Prophylactic effectiveness with Amp-LPNs at a concentration of 250 μg/mL was exhibited in both bacteria elimination and protozoa survival toward subsequent infections. Using protozoa as a surrogate model for animal phagocytes to study high MOI infections, this study suggests that LPN-formulated antibiotics hold the potential to significantly improve the therapeutic outcome in highly complicated bacterial infections.

Adsorption, desorption and coadsorption behaviors of sulfamerazine, Pb(II) and benzoic acid on carbon nanotubes and nano-silica

In this study, nano-silica (Nano-SiO₂), oxidized (O-CNTs) and graphitized multi-walled carbon nanotubes (G-CNTs) were applied as model adsorbents to study the adsorption, desorption and coadsorption behaviors of sulfamerazine (SMR), Pb(II) and benzoic acid (BA). The results showed that charge assisted H-bond (CAHB) formation played an important role in adsorption of SMR and BA on O-riched nanomaterials. The adsorption capacities of Pb(II) on CNTs were 21.46- 26.77 times higher than that on Nano-SiO₂, which was mainly attributed to surface complexation and cation-π interaction. The fraction of Pb²⁺ adsorbed in the inside channel of CNTs should not be ignored. In coexisting systems, the absolute sorption inhibition of the SMR (ΔQ_e^SMR) was compared with the amount of competitor adsorbed. Competitive sorption was observed as indicated by adding Pb(II) decreased adsorption of SMR on Nano-SiO₂ (ΔQ_e^SMR > 0), but hardly affected SMR adsorption on CNTs (ΔQ_e^SMR ≈ 0) which was attributed to cation-π interaction. In addition, CAHB formed between SMR and Nano-SiO₂ (ΔpK_a ≈ 4.34) was weaker than that formed between SMR and O-CNTs (ΔpK_a ≈ 3.15), which also consequently resulted in stronger competition of Pb(II) to SMR on Nano-SiO₂ than that on O-CNTs. Moreover, coexisting BA increased adsorption of SMR on Nano-SiO₂ and G-CNTs (ΔQ_e^SMR < 0), but did not result in an apparent competition on SMR adsorption by O-CNTs (ΔQ_e^SMR ≈ 0). These results emphasize that the environmental behaviors of a certain pollutant should be assessed carefully by considering the presence of other pollutants.

Determination of optimal operating parameters for tetracycline removal by adsorption from synthetic and real aqueous solutions

Among all emerging contaminants, pharmaceutical compounds as tetracycline (TC) can cause potential environmental impact in water quality. In this work, the removal of TC drug on activated carbon from aqueous solution was studied and the best operating parameters were obtained. In addition, a real aqueous matrix was enriched with TC and the optimized conditions were applied to study the adsorption process efficiency. For this, the influence of pH, contact time between phases and dosage of adsorbent solid was evaluated. The investigation of kinetics, equilibrium and thermodynamic was also performed. The adsorbent material was characterized by SEM analysis and N₂ adsorption/desorption isotherms to confirm its properties. Batch experiments showed that the most suitable experimental conditions for adsorption in aqueous solution were: pH 4.0, contact time 90 min and dosage of adsorbent solid 30 g.L^-1. Under these conditions, it was possible to obtain 92.7% of TC removal with predominance of a spontaneous, favorable and endothermic chemisorption process. Adsorption experiments with real aqueous matrix provided 99.4% TC removal. These results show the potential of adsorption as a wastewater treatment applied to remove emerging pollutants as TC from real aqueous contaminated water.

Amino Functionalized Micro-Mesoporous Hybrid Particles for the Sustained Release of the Antiretroviral Drug Tenofovir

The sustained release of an antiretroviral agent to women mucosa has been proved as an excellent strategy to reduce the sexual transmission of HIV. Hybrid micro-mesoporous particles have been synthesized and functionalized with a silane coupling agent followed by loading the antiretroviral tenofovir. It has been observed that the disposition of the silane molecule on the surface of the particles determines the interaction mechanism with the antiretroviral molecule loaded independently on the surface area of the particles. In this sense, available and free amino groups are required to achieve a smart pH-responsive material, a condition that is only achieved in those materials containing a silane chemisorbed monolayer. Moreover, the modulation of the release kinetics attributed to the presence of the silane monolayer covering the mesopores has been confirmed by fitting the releasing curves to the first order and Weibull models. The developed micro-mesoporous particles have been demonstrated to be excellent smart-release vehicles for antiviral agents and can be safely used in polymer mucoadhesive vaginal gels.

Physical, Thermal, and Antibacterial Effects of Active Essential Oils with Potential for Biomedical Applications Loaded onto Cellulose Acetate/Polycaprolactone Wet-Spun Microfibers

New approaches to deal with the growing concern associated with antibiotic-resistant bacteria are emerging daily. Essential oils (EOs) are natural antimicrobial substances with great potential to mitigate this situation. However, their volatile nature, in their liquid-free form, has restricted their generalized application in biomedicine. Here, we propose the use of cellulose acetate (CA)/polycaprolactone (PCL) wet-spun fibers as potential delivery platforms of selected EOs to fight infections caused by Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). Twenty EOs were selected and screened for their minimal inhibitory concentration (MIC), using the antibiotic ampicillin as positive control. The cinnamon leaf oil (CLO), cajeput oil (CJO), and the clove oil (CO) were the most effective EOs, against the Gram-positive (MIC < 22.38 mg/mL) and the Gram-negative (MIC < 11.19 mg/mL) bacteria. Uniform microfibers were successfully wet-spun from CA/PCL with an averaged diameter of 53.9 ± 4.5 µm, and then modified by immersion with CLO, CJO and CO at 2 × MIC value. EOs incorporation was confirmed by UV-visible spectroscopy, Fourier-transformed infrared spectroscopy, and thermal gravimetric analysis. However, while microfibers contained ampicillin at MIC (control) after the 72 h modification, the CLO, CO and CJO-loaded fibers registered ≈ 14%, 66%, and 76% of their MIC value, respectively. Data showed that even at small amounts the EO-modified microfibers were effective against the tested bacteria, both by killing bacteria more quickly or by disrupting more easily their cytoplasmic membrane than ampicillin. Considering the amount immobilized, CLO-modified fibers were deemed the most effective from the EOs group. These results indicate that CA/PCL microfibers loaded with EOs can be easily produced with increased antibacterial action, envisioning their use as scaffolding materials for the treatment of infections.

Assessment of ampicillin removal efficiency from aqueous solution by polydopamine/zirconium(iv) iodate: optimization by response surface methodology

Polydopamine/zirconium(iv) iodate was prepared by incorporating polydopamine into zirconium iodate gel and studied as an effective adsorbent for ampicillin. In order to characterize the prepared composite, FTIR, XRD, TGA-DTA, SEM and TEM were used. The effects of experimental variables on ampicillin removal were examined using response surface methodology. The optimum conditions for ampicillin removal were 7, 130 min, 20 mg/20 mL and 50 mg L-1 for pH, contact time, adsorbent dose and initial ampicillin concentration, respectively. Under the optimum conditions, the maximum ampicillin removal percentage was found to be 99.12%. The Langmuir isotherm and pseudo-second-order kinetic models explained the removal process more appropriately. The maximum adsorption capacity at 303 K was 100.0 mg g-1. Thermodynamic study revealed that the ampicillin adsorption was spontaneous and endothermic in nature. The reusability of the prepared material was also explored.

Preparation and characterisation of silica-based nanoparticles for cisplatin release on cancer brain cells

In the present work, the preparation, characterisation, and efficiency of two different silica nanostructures as release vehicles of Cisplatin are reported. The 1-hexadeciltrimethyl-ammonium bromide templating agent was used to obtain mesoporous silica nanoparticles which were later loaded with Cisplatin. While sol-gel silica was very fast prepared using an excess of acetic acid during the hydrolysis-condensation reactions of tetraethylorthosilicate and at the same time the Cisplatin was added. Several physicochemical techniques including spectroscopies, electronic microscopy, X-ray diffraction, N2 adsorption-desorption were used to characterise the silica nanostructures. An in vitro Cisplatin release test was carried out using artificial cerebrospinal fluid. Finally, the toxicity of all silica nanostructures was tested using the C6 cancer cell line. The spectroscopic results showed the suitable stabilisation of Cisplatin into the two different silica nanostructures. A large surface area was obtained for the mesoporous silica nanoparticles, while low areas were obtained in the silica nanoparticles. Cisplatin was released faster from mesoporous silica channels than from inside of aggregates nanoparticles silica. Cisplatin alone, as well as, cisplatin released from both silica nanostructures exerted a toxic effect on cancer cells. In contrast, both silica structures without the drug did not exert any toxic effect.

Antibacterial Effect of Thymol Loaded SBA-15 Nanorods Incorporated in PCL Electrospun Fibers

For the effective management of infected chronic wounds, the incorporation of antimicrobial drugs into wound dressings can increase their local availability at the infection site. Mesoporous silicon dioxide SBA-15 is an excellent drug carrier with tunable drug release kinetics. In this work, synthesized SBA-15 loaded with the natural antimicrobial compound thymol (THY) was incorporated into polycaprolactone (PCL) electrospun nanofibers to obtain an advanced wound dressing. Rod-shaped particles with internal parallel channels oriented along the longitudinal axis (diameter: 138 ± 30 nm, length: 563 ± 100 nm) were loaded with 70.8 wt.% of THY. Fiber mats were prepared using these particles as nanofillers within polycaprolactone (PCL) electrospun fibers. The resulting mats contained 5.6 wt.% of THY and more than half of this loading was released in the first 7 h. This release would prevent an initial bacterial colonization and also inhibit or eliminate bacterial growth as in vitro shown against Staphylococcus aureus ATCC 25923. Minimal inhibitory concentration (MIC: 0.07 mg/mL) and minimal bactericidal concentration (MBC: 0.11 mg/mL) of released THY were lower than the amount of free THY required, demonstrating the benefit of drug encapsulation for a more efficient bactericidal capacity due to the direct contact between mats and bacteria.

Ali S, Salerno M, Eldin MSM. Effective Elimination of Contaminant Antibiotics Using High-Surface-Area Magnetic-Functionalized Graphene Nanocomposites Developed from Plastic Waste

The presence of pharmaceutical residues in aquatic environments represents a risk for the equilibrium of the ecosystem and may seriously affect human safety itself in the long term. To address this issue, we have synthesized functional materials based on highly-reduced graphene oxide (HRGO), sulfonated graphene (SG), and magnetic sulfonated graphene (MSG). The method of synthesis adopted is simple and inexpensive and makes use of plastic bottle waste as the raw material. We have tested the fabricated materials for their adsorption efficiency against two model antibiotics in aqueous solutions, namely Garamycin and Ampicillin. Our tests involved the optimization of different experimental parameters of the adsorption process, such as starting antibiotic concentration, amount of adsorbent, and time. Finally, we characterized the effect of the antibiotic adsorption process on common living organisms, namely Escherichia coli DH5α (E. coli DH5α) bacteria. The results obtained demonstrate the efficiency of the method in addressing the issue of the emergence of antibiotic-resistant bacteria, which will help in preventing changes in the ecosystem.

Reactive Adsorption of Parabens on Synthesized Micro- and Mesoporous Silica from Coal Fly Ash: pH Effect on the Modification Process

Parabens are widely used as preservatives in food, pharmaceutical, and cosmetic products. These compounds are known for their estrogen agonist activity. This research investigates the synthesis of micro- and mesoporous silica from coal fly ash at different pH values (13, 11, 9, and 7) as well as its use as an adsorbent for the removal of parabens. The materials were characterized, and X-ray fluorescence (XRF) analysis revealed that the fly ash acid treatment reduced the presence of aluminum, iron, and calcium oxides and also that silica synthesized at lower pH values (7 and 9) showed a higher SiO₂ content. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses revealed microporous silica formation for silica synthesized at pH 13 and mesoporous silica at pH 7, 9, and 11. Adsorption tests were performed with materials, and FA-AT7 showed a higher adsorption capacity. The effect of factors (A) adsorbent mass, (B) initial paraben concentration, and (C) agitation rate on the adsorption process was studied for the FA-AT7 adsorbent using a factorial experimental design. Standardized Pareto charts revealed a negative effect of factor A, positive effect of factor B, and negative interaction effects of factors A-B for all studied parabens. Isotherms and multicomponent kinetic studies were performed. A linear type-III isotherm was obtained, and adsorption equilibrium was reached at approximately 10 min.