A non-enzymatic hydrogen peroxide sensor based on vertical NiO nanosheets supported on the graphite sheet

CO2-plasma surface treatment of graphite sheet electrodes for detection of chloramphenicol, ciprofloxacin and sulphanilamide

Graphite sheet (GS) electrodes are flexible and versatile substrates for sensing electrochemical; however, their use has been limited to incorporate (bio)chemical modifiers. Herein, we demonstrated that a cold (low temperature) CO2 plasma treatment of GS electrodes provides a substantial improvement of the electrochemical activity of these electrodes due to the increased structural defects on the GS surface as revealed by Raman spectroscopy (ID/IG ratio), and scanning electron microscopy images. XPS analyses confirmed the formation of oxygenated functional groups at the GS surface after the plasma treatment that are intrinsically related to the substantial increase in the electron transfer coefficient (K0 values increased from 1.46 × 10-6 to 2.09 × 10-3 cm s-1) and with reduction of the resistance to charge transfer (from 129.8 to 0.251 kΩ). The improved electrochemical activity of CO2-GS electrodes was checked for the detection of emerging contaminant species, such as chloramphenicol (CHL), ciprofloxacin (CIP) and sulphanilamide (SUL) antibiotics, at around + 0.15, + 1.10 and + 0.85 V (versus Ag/AgCl), respectively, by square wave voltammetry. Limit of detection values in the submicromolar range were achieved for CHL (0.08 μmol L-1), CIP (0.01 μmol L-1) and SFL (0.11 μmol L-1), which enabled the sensor to be successfully applied to natural waters and urine samples (recovery values from 85 to 119%). The CO2-GS electrode is highly stable and inexpensive ($0.09 each sensor) and can be easily inserted in portable 3D printed cells for environmental on-site analyses.

Copper and Nickel Microsensors Produced by Selective Laser Reductive Sintering for Non-Enzymatic Glucose Detection

In this work, the method of selective laser reductive sintering was used to fabricate the sensor-active copper and nickel microstructures on the surface of glass-ceramics suitable for non-enzymatic detection of glucose. The calculated sensitivities for these microsensors are 1110 and 2080 μA mM⁻¹·cm⁻² for copper and nickel, respectively. Linear regime of enzymeless glucose sensing is provided between 0.003 and 3 mM for copper and between 0.01 and 3 mM for nickel. Limits of glucose detection for these manufactured micropatterns are equal to 0.91 and 2.1 µM for copper and nickel, respectively. In addition, the fabricated materials demonstrate rather good selectivity, long-term stability and reproducibility.

Porous carbon-NiO nanocomposites for amperometric detection of hydrazine and hydrogen peroxide

A hydrothermal route is reported for the preparation of a composite consisting of sheet-like glucose-derived carbon and nickel oxide nanoparticles. The nanocomposites were prepared at different annealing temperatures and exploited as electrode materials for amperometric (i-t) determination of hydrazine (N₂H₄) and hydrogen peroxide (H₂O₂) at trace levels. The performances of the sensors were assessed by cyclic voltammetry and amperometry detection using a rotating disk electrode (RDE) technique. The modified electrode annealed at ca. 300 °C was found to exhibit the best electrocatalytic performance in terms of sensitive and selective detection of N₂H₄ and H₂O₂ even in the presence of interfering species. The electrode is inexpensive, robust, easy to prepare in large batches, highly stable, and has a low overpotential. H₂O₂ can be sensed, best at a working voltage of typically 0.13 V vs Ag/AgCl; rotationg speed 1200 rpm) over a wide concentration range (0.01 to 3.9 µM) with a detection limit of 1.5 nM. N₂H₄ can be sensed, best at a working voltage of typically 0.0 V within the concentration range from 0.5 μM to 12 mM with an excellent detection limit of 1.5 µM. Thus, this cost-effective and robust modified electrode, which may be readily prepared in large batch quantity, represents a practical platform for industrial sensing. Graphical abstract Schematic of the hydrothermal method for synthesis of carbon and nickel oxide nanoparticle composites (GCD/NiO-150, GCD/NiO-300, and GCD/NiO-450). The composite was used for the electro-oxidation of hydrazine (N₂H₄) and hydrogen peroxide (H₂O₂) by cyclic voltammetry and amperometry (i-t).

In situ laser-induced codeposition of copper and different metals for fabrication of microcomposite sensor-active materials

We report one-step in situ laser-induced synthesis of the conductive copper microstructures doped with iron, zinc, nickel, and cobalt with highly developed surface area. It was observed that the presence of chlorides of the aforementioned metals in the solutions used in our experiments increases the deposition rate and the amount of copper in the resulting deposits; it also leads to the deposit miniaturization. The laser deposition from solutions containing cobalt (II) chloride of concentration more than 0.003 M results in fabrication of copper microelectrode with better electrochemical properties than those deposited from solutions containing chlorides of other metals of the same concentration. Moreover, copper microelectrode doped with cobalt has demonstrated good reproducibility and long-run stability as well as sensitivity and selectivity towards determination of hydrogen peroxide (limit of detection-0.2 μM) and d-glucose (limit of detection-2.2 μM). Thus, in this article we have shown the opportunity to manufacture two-phase microcomposite materials with good electrical conductivity and electrochemical characteristics using in situ laser-induced metal deposition technique. These materials might be quite useful in development of new perspective sensors for non-enzymatic detection of such important analytes as hydrogen peroxide and glucose.

Microstructured prealloyed Titanium-Nickel powder as a novel nonenzymatic hydrogen peroxide sensor

At present, commercial pure Titanium (Ti) and microstructured pre-alloyed Titanium-Nickel (TiNi) powders are employed as a sensitive electrochemical hydrogen peroxide (H₂O₂) sensor. Surface characterization of these materials are performed by x-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical characterization is achieved via cyclic voltammetry (CV), chronoamperometry (CA), and electrochemical impedance spectroscopy (EIS) on Ti and TiNi modified glassy carbon electrode (GCE). The electrochemical behavior of H₂O₂ at the pure Ti/GCE and microstructure pre-alloyed TiNi/GCE are studied by CV in 0.1 M phosphate buffer solution (PBS) containing as the supporting electrolyte. In addition, CA is employed for the determination of H₂O₂ at the applied potential of 0 V vs. Ag/AgCl. The sensor has a linear response range of 0.5-17.5 mM with a sensitivity of 280 µA mM^-1 cm^-2. Moreover, the limit of detection (LOD) and limit of quantification (LOQ) are 0.5 µM and 1.7 µM, respectively. The electrochemical sensor exhibits fast and selective responses to H₂O₂ concentration. The applicability of the sensor is checked using a hair coloring as a real sample with satisfactory results.

Mesoporous NiO nanosphere: a sensitive strain sensor for determination of hydrogen peroxide

Exploring the sensitive and reliable methods for the determination of hydrogen peroxide (H₂O₂) is a crucial issue for the health and environmental challenges. Herein, we demonstrate a facile, but rational and effective solvothermal approach to the synthesis of hierarchical NiO mesoporous nanospheres (NiO-MNS) as an effective non-enzymatic sensor towards the H₂O₂ detection. Owing to the intercalation and stabilization effect of polyethylene glycol for the Ni(OH)₂ intermediate, the NiO mesoporous nanosphere (NiO-MNS) product is consistent with the low-dimensional nanostructured NiO blocks with large surface area and plentiful mesopores after the calcination treatment. The obtained NiO-MNS sensor presents superior electrochemical performance with a high sensitivity (236.7 μA mM⁻¹ cm⁻²) and low limit of detection (0.62 μM), as well as the good selectivity and reliability for the further application of H₂O₂ detection. In addition, the unraveling mechanism of the mesopores formation derived from the in situ measurements also offers the valuable guidance for the future design of porous materials for electrochemical devices and other applications.

The NiO mesoporous nanosphere constructing from the low-dimensional nanostructured NiO blocks presents the excellent electrochemical activity for H₂O₂ detection.

Non-enzymatic sensors based on in situ laser-induced synthesis of copper-gold and gold nano-sized microstructures

The synthesis of conductive gold and copper-gold microstructures with high developed surface based on the method of laser-induced metal deposition from solution was developed. The topology and crystallization phase of these structures were observed by means of scanning electron microscopy and X-ray diffraction, respectively. The electrochemical properties of the synthesized materials were investigated using cyclic voltamperometry and amperometry. According to the obtained results, it was found out that copper-gold microstructures demonstrate a linear dependence of Faraday current vs. concentration from 0.025 to 5µM for D-glucose and from 0.025 to 10µM for hydrogen peroxide. In turn, gold deposit exhibits a linear dependence of Faraday current vs. concentration from 0.025 to 50µM for D-glucose and from 0.025 to 1µM for hydrogen peroxide. Moreover, the synthesized materials reveal low detection limits (0.025µM) with respect to the aforementioned analytes, which is quite promising for their potential application in design and fabrication of new non-enzymatic biosensors.

Ultrasensitive electrochemical assay of hydrogen peroxide and glucose based on PtNi alloy decorated MWCNTs

A electrochemical sensor based on PtNi/MWCNTs can detect hydrogen peroxide and glucose with wide linear range and high sensitivity.