Sulfate radicals mediated oxidation of amoxicillin: Optimization of key parameters

A Box-Behnken design-based chemometric approach to optimize the sono-photodegradation of hydroxychloroquine in water media using the Fe(0)/S2O82-/UV system

The huge utilization of hydroxychloroquine in autoimmune infections led to an abnormal increment in its concentration in wastewater, which can pose a real risk to the environment, necessitating the development of a pretreatment technique. To do this, we are interested in researching how hydroxychloroquine degrades in contaminated water. The main goal of this investigation is to optimize the operating conditions for the sono-photodegradation of hydroxychloroquine in water using an ultrasound-assisted Fe(0)/S 2 O 8 2 - /UV system. To get adequate removal of HCQ, a chemometric method based on the Box-Behnken design was applied to optimize the influence of the empirical parameters selected, including Fe(0) dose,S 2 O 8 2 - concentration, pH, and initial HCQ concentration. The quadratic regression model representing the HCQ removal rate (η(%)) was evolved and validated by ANOVA. The optimal conditions as a result of the above-mentioned trade-off between the four input variables, with η(%) as the dependent output variable, were captured using RSM methodology and the composite desirability function approach. For HCQ full decomposition, the optimal values of the operating factors are as follows:S 2 O 8 2 - dose, 194.309 mg/L; Fe(0) quantity, 198.83 mg/L; pH = 2.017, and HCQ initial dose of 296.406 mg/L. Under these conditions, the HCQ removal rate, achieved after 60 min of reaction, attained 98.95%.

PI3K-AKT-mTOR signaling pathway regulates autophagy of hippocampal neurons in diabetic rats with chronic unpredictable mild stress

It is reported that the co-morbidities of diabetes and depression will be a new challenge for humanity. However, the underlying mechanism is not clear. The present study investigated the histopathology, autophagy of hippocampal neurons, and the PI3K-AKT- mTOR signaling pathway in type 2 diabetes with depression（T2DD） rats. The results showed that, the chronic unpredictable mild stress (CUMS), Type 2 diabetes mellitus (T2DM) and T2DD in rats were induced successfully. Compared with the CUMS and T2DM groups, the T2DD group performed significantly fewer autonomic activities in the open-field test, and longer immobile in the force swimming test, and increasing of Corticosterone (CORT) in blood. The number of pyknotic neurons at cornu ammonis 1 (CA1) and dentate gyrus (DG) of the hippocampus in T2DD was significantly increased compared with CUMS and T2DM groups. Moreover, compared with the CUMS and T2DM groups, the mitochondrial autophagosomes were most abundant in the T2DD group. As shown in western blot and immunofluorescence, compared with the control group, in the CUMS, T2DM and T2DD groups, significantly increased expression of Beclin-1 and LC3B and decreased P62 were detected. In the PC12 cells, the relative amount of parkin and LC3B in the CORT+HG group was significantly higher than that in the CORT and HG groups. Compared with the control group, p-AKT/AKT and p-mTOR/mTOR in CUMS, T2DM and T2DD groups were significantly decreased. Compared with the CUMS group, p-AKT/AKT, p-PI3K/PI3K and p-mTOR/mTOR in the T2DD group exhibited further decrease. Similar results were obtained in PC12 cells in vitro. It is suggests that memory and cognitive impairment in rats with co-morbidities of diabetes and depression might be related with hippocampal neuronal damage and autophagy increase, which was involved in the PI3K-AKT-mTOR signaling pathway.

Design and synthesis of high performance magnetically separable exfoliated g-C3N4/γ-Fe2O3/ZnO yolk-shell nanoparticles: a novel and eco-friendly photocatalyst toward removal of organic pollutants from water

Herein, a new visible-light active exfoliated g-C3N4/γ-Fe2O3/ZnO yolk-shell nanoparticles (NPs) was synthesized as a magnetically separable photocatalyst. For an in-depth understanding of the magnetic photocatalyst's structural, morphological, and optical properties, the products were extensively characterized with FT-IR, XRD, TEM, HRTEM, FESEM, EDS, EDS-mapping, VSM, DRS, EIS, and photocurrent. The photocatalyst was then utilized to degrade Levofloxacin (LEVO) and Indigo Carmine (IC) by visible light at room temperature. The exfoliated g-C3N4/γ-Fe2O3/ZnO yolk-shell NPs photocatalyst revealed 80% and 95.6% degradation efficiency for Levofloxacin and Indigo Carmine within 25 and 15 min, respectively. In addition, the optimal factors such as concentration, loading of photocatalyst, and pH were also assessed. Levofloxacin degradation mechanistic studies showed that electrons and holes significantly contribute to the photocatalytic process of photocatalyst degradation. In addition, after 5 times regeneration, exfoliated g-C3N4/γ-Fe2O3/ZnO yolk-shell NPs remained as an excellent magnetic photocatalyst for the eco-friendly degradation of Levofloxacin and Indigo Carmine (76% and 90%), respectively. The superior photocatalytic performance of exfoliated g-C3N4/γ-Fe2O3/ZnO yolk-shell nanoparticles (NPs) was mostly ascribed to the synergistic advantages of stronger visible light response, larger specific surface area, and the more effective separation and transfer of photogenerated charge carriers. Based on these results, the highly effective magnetic photocatalyst achieved better results than numerous studied catalysts in the literature. The degradation of Levofloxacin and Indigo Carmine under environmentally friendly conditions can be achieved using exfoliated g-C3N4/γ-Fe2O3/ZnO yolk-shell NPs (V) as an efficient and green photocatalyst. The magnetic photocatalyst was characterized by spectroscopic and microscopic methods, revealing a spherical shape and particle size of 23 nm. Additionally, the magnetic photocatalyst could be separated from the reaction mixture by a magnet without significantly reducing its catalytic activity.

Biochar loaded with cobalt ferrate activated persulfate to degrade naphthalene

Considering the simple preparation of biochar and the excellent activation performance of cobalt ferrate material, a biochar supported cobalt ferrate composite was synthesized by a solvothermal method. The material was used to activate persulfate (PS) to degrade naphthalene (NAP) in water. The structure and morphology characterization showed that the composite (CoFe₂O₄-BC) was successfully prepared. Under the conditions of 0.25 g L^-1 CoFe₂O₄-BC and 1 mM PS, 90.6% NAP (the initial concentration was 0.1 mM) was degraded after 30 minutes. The degradation kinetics of NAP followed the pseudo-first-order kinetic model with a rate constant of 0.0645 min^-1. With the increase of the dosage of activator and PS, the removal rate of NAP could be increased to 99.5%. The coexistence of anions and humic acids inhibited the removal of NAP. The acid environment promoted the removal of NAP while the alkaline environment inhibited it. After four cycles of CoFe₂O₄-BC material, the removal rate of NAP decreased from 90.6% to 79.4%. The removal of TOC was about 45% after each cycle. After the first cycle, the concentration of leached cobalt ion and leached iron ion was about 310 μg L^-1 and 30 μg L^-1 respectively. The free radical quenching experiments showed that SO₄ ^-˙ and OH˙ were the main causes of NAP removal, and the possible degradation path of NAP was elucidated by DFT calculation.

Sulfate radicals-based advanced oxidation processes for the degradation of pharmaceuticals and personal care products: A review on relevant activation mechanisms, performance, and perspectives

Owing to the rapid development of modern industry, a greater number of organic pollutants are discharged into the water matrices. In recent decades, research efforts have focused on developing more effective technologies for the remediation of water containing pharmaceuticals and personal care products (PPCPs). Recently, sulfate radicals-based advanced oxidation processes (SR-AOPs) have been extensively used due to their high oxidizing potential, and effectiveness compared with other AOPs in PPCPs remediation. The present review provides a comprehensive assessment of the different methods such as heat, ultraviolet (UV) light, photo-generated electrons, ultrasound (US), electrochemical, carbon nanomaterials, homogeneous, and heterogeneous catalysts for activating peroxymonosulfate (PMS) and peroxydisulfate (PDS). In addition, possible activation mechanisms from the point of radical and non-radical pathways are discussed. Then, biodegradability enhancement and toxicity reduction are highlighted. Comparison with other AOPs and treatment of PPCPs by the integrated process are evaluated as well. Lastly, conclusions and future perspectives on this research topic are elaborated.

A review of radical and non-radical degradation of amoxicillin by using different oxidation process systems

Pharmaceutical compounds have piqued the interest of researchers due to an increase in their demand, which increases the possibility of leakage into the environment. Amoxicillin (AMX) is a penicillin derivative used for the treatment of infections caused by gram-positive bacteria. AMX has a low metabolic rate in the human body, and around 80-90% is unmetabolized. As a result, AMX residuals should be treated immediately to avoid further accumulation in the environment. Advanced oxidation process techniques are an efficient way to degrade AMX. This review attempts to collect, organize, summarize, and analyze the most up to date research linked to the degradation of AMX by different advanced oxidation process systems including photocatalytic, ultrasonic, electro-oxidation, and advanced oxidation process-based on partials. The main topics investigated in this review are degradation mechanism, degradation efficiency, catalyst stability, the formation of AMX by-products and its toxicity, in addition, the influence of different experimental conditions was discussed such as pH, temperature, scavengers, the concentration of amoxicillin, oxidants, catalyst, and doping ratio. The degradation of AMX could be inhibited by very high values of pH, temperature, AMX concentration, oxidants concentration, catalyst concentration, and doping ratio. Several AMX by-products were discovered after oxidation treatment, and several of them had lower or same values of LC₅₀ (96 h) fathead minnow of AMX itself, such as m/z 384, 375, 349, 323, 324, 321, 318, with prediction values of 0.70, 1.10, 1.10 0.42, 0.42, 0.42, and 0.42 mg/L, respectively. We revealed that there is no silver bullet system to oxidize AMX from an aqueous medium. However, it is recommended to apply hybrid systems such as Photo-electro, Photo-Fenton, Electro-Fenton, etc. Hybrid systems are capable to cover the drawbacks of the single system. This review may provide important information, as well as future recommendations, for future researchers interested in treating AMX using various AOP systems, allowing them to improve the applicability of their systems and successfully oxidize AMX from an aqueous medium.

Comparing the efficacy of various methods for sulfate radical generation for antibiotics degradation in synthetic wastewater: degradation mechanism, kinetics study, and toxicity assessment

In the present study the aim was to investigate and compare various activation processes for amoxicillin degradation. UV radiation, ultrasound, heat, and hydrogen peroxide were selected as the persulfate activation methods. The effects of various parameters such as pH, persulfate concentration, reaction time, AMX concentration, radical scavengers, and anions were thoroughly investigated. The results showed that AMX degradation was following the pseudo-first order kinetic model. The reaction rate of 0.114 min-1 was calculated for the UV/PS process, which was higher than that of the other investigated processes. The AMX degradation mechanism and pathway investigations revealed that sulfate and hydroxyl radicals were responsible for the degradation of AMX by two degradation pathways of hydroxylation and the opening of the β-lactam ring. Competition kinetic analysis showed that the second-order rate constant of AMX with sulfate radicals was 8.56 × 109 L mol-1 s-1 in the UV/PS process. Cost analysis was conducted for the four investigated processes and it was found that 1.9 $m-3 per order is required in the UV/PS process for the complete destruction of AMX. Finally, cytotoxic assessment of the treated effluent on human embryonic kidney cells showed a considerable reduction in AMX-induced cell cytotoxicity, proving that the investigated process is sufficiently capable of completely destroying AMX molecules to nontoxic compounds. Therefore, it can be concluded that UV radiation is much more effective than other methods for persulfate activation and can be considered as a reliable technique for antibiotic removal.

Elimination of amoxicillin using zeolite Y-sea salt as a good catalyst for activation of hydrogen peroxide: Investigating degradation pathway and the effect of wastewater chemistry

The sea contains elements that can play a useful role in catalyzing reactions. Therefore, this research was done to focus on eliminating amoxicillin (AMX) from wastewater utilizing zeolite Y- sea salt catalyst in the presence of H₂O₂. The influences of furnace temperature (200-500 °C) and time duration in the furnace (1-4 h) were optimized during catalyst generation. Also, the effects of different parameters on AMX removal, such as pH (5.0-9.0), catalyst dose (0-10 g.L^-1), AMX concentration (50-300 mg.L^-1), contact time (10-130 min), and H₂O₂ concentration (0-6 mL/100 mL distilled water) were investigated. Different analyses like Brunauer-Emmett-Teller (BET), Fourier transform infrared (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA) were conducted to reveal catalyst properties. The BET-specific surface area of the catalyst (12.69 m²g^-1) insignificantly (p-value > 0.05) changed after AMX removal (13.04 m²g^-1), indicating the strength of the prepared catalyst. The active groups of N-H, O-H-O, O-Si-O, C-H, Si-O-Si, and Si-O-Al were determined in the catalyst structure. The highest removal of AMX (93%) was achieved in the zeolite-sea salt/H₂O₂ system at a pH level of 6.0 and an H₂O₂ concentration of 0.1 mL/100 mL. Elimination of the AMX followed pseudo-first-order kinetics. The catalyst was reclaimed up to 7 times and the removal efficiency was suitable up to the fifth stage. The by-products and reaction pathways were investigated by gas chromatography-mass spectrometry (GC-MS). The results showed that zeolite-sea salt can be utilized as an H₂O₂ activator for the effective degradation of AMX from wastewater.

A microwave irradiation-persulfate-formate system for achieving the detoxification and alkali-activated composite geopolymerization of the chromate-contaminated soil

A microwave (MA) irradiation-persulfate-formate system was constructed to detoxify Cr contamination and solidify the geopolymerization of the alkali-activated composite material. Three series of experiments were correspondingly conducted to evaluate the treatment for the chromate-contaminated soil. The changes in the molar ratios of formate to persulfate and the mass rates of fortifier to soil led to a significantly greater reduction of Cr^VI in the detoxification experiments. The increase of blast furnace slag from 50% to 80% in the composite cementitious materials (CCM) intensified the immobilization efficiencies of chromate and the compressive strengths of geopolymer blocks. MA irradiation potentially enhanced the binding of Ca cations to the aluminosilicate compounds. The degree of reaction in the phenomenological kinetics model mathematically verified the geopolymerization process. Ettringite was formed within the structure of the geopolymer in the coupling system. Sulfate radicals released from persulfate not only contributed to the detoxification process but also strengthened the immobilization process.

Waste sludge from shipping docks as a catalyst to remove amoxicillin in water with hydrogen peroxide and ultrasound

The waste sludge from shipping docks contains important elements that can be used as a catalyst after proper processing. The purpose of this study was to remove of amoxicillin (AMX) from the aquatic environment using waste sludge from shipping docks as catalyst in the presence of hydrogen peroxide/ultrasound waves. The catalyst was produced by treating waste sludge at 400 °C for 2 h. N₂ adsorption, SEM, XRD, XRF, and FTIR techniques characterized the structural and physical properties of the catalyst. The BET-specific surface area of the catalyst reduced after AMX removal from 4.4 m²/g to 3.6 m²/g. To determine the optimal removal conditions, the parameters of the design of experiments were pH (5-9), contaminant concentration (5-100 mg/L), catalyst dosage (0.5-6 g/L), and concentration of hydrogen peroxide (10-100 mM). The maximum removal of AMX (98%) was obtained in the catalyst/hydrogen peroxide/ultrasound system at pH 5, catalyst dose of 4.5 g/L, H₂O₂ concentration of 50 mM, AMX concentration of 5 mg/L, and contact time of 60 min. The kinetics of removal of AMX from urine (k = 0.026 1/min), hospital wastewater (k = 0.021 1/min), and distilled water (k = 0.067 1/min) followed a first-order kinetic model (R²>0.91). The catalyst was reused up to 8 times and the AMX removal decreased to 45% in the last use. The byproducts and reaction pathway of AMX degradation were also investigated. The results clearly show that to achieve high pollutant removal rate the H₂O₂/ultrasound and catalyst/ultrasound synergy plays a key role.

Instantaneous oxidation of levofloxacin as toxic pharmaceutical residuals in water using clay nanotubes decorated by ZnO (ZnO/KNTs) as a novel photocatalyst under visible light source

Kaolinite nanotubes were synthesized by a simple scrolling process and decorated by ZnO nanoparticles as a novel nanocomposite (ZnO/KNTs). The synthetic ZnO/KNTs composite was characterized as an effective photocatalyst in the oxidation of levofloxacin pharmaceutical residuals in the water resources. The composite displays a surface area of 95.4 m²/g, average pore diameter of 5.8 nm, and bandgap energy of 2.12 eV. It is of high catalytic activity in the oxidation of levofloxacin in the presence of visible light source. The complete oxidation for 10 mg/L of levofloxacin was recognized after 55 min, 45 min, and 30 min with applying 30 mg, 40 mg, and 50 mg of ZnO/KNTs as catalyst dosage, respectively. Additionally, it achieved complete oxidation for 20 mg/L and 30 mg/L of levofloxacin after 45 min and 75 min, respectively using 50 mg as catalyst dosage. The degradation efficiency was confirmed by detecting the residual TOC after the treatment tests and the formed intermediate compounds were identified to suggest the degradation pathways. In addition to the oxidation pathway, the mechanism was evaluated based on the active trapping tests that proved the dominance of hydroxyl radicals as the essential active species. Finally, the ZnO/KNTs composite is of promising recyclability properties and achieved better results than several studied photocatalysts in literature.