Megamerger of biosorbents and catalytic technologies for the removal of heavy metals from wastewater: Preparation, final disposal, mechanism and influencing factors

Untapped potential of food waste derived biochar for the removal of heavy metals from wastewater

The presence of heavy metals in water pose a serious threat to both public and environmental health. However, the advances in the application of low cost biochar based adsorbent synthesize from various feedstocks plays an effective role in the of removal heavy metals from water. This study implies the introduction of novel method of converting food waste (FW) to biochar through pyrolysis, examine its physiochemical characteristics, and investigate its adsorption potential for the removal of heavy metals from water. The results revealed that biochar yield decreased from 18.4 % to 14.31 % with increase in pyrolysis temperature from 350 to 550 °C. Likewise, increase in the pyrolysis temperature also resulted in the increase in the ash content from 39.87 % to 42.05 % thus transforming the biochar into alkaline nature (pH 10.17). The structural and chemical compositions of biochar produced at various temperatures (350, 450, and 550 °C) showed a wide range of mineralogical composition, and changes in the concentration of surface functional groups. Similarly, the adsorption potential showed that all the produced biochar effectively removed the selected heavy metals from wastewater. However a slightly high removal capacity was observed for biochar produced at 550 °C that was credited to the alkaline nature, negatively charged biochar active sites due to O-containing functional groups and swelling behavior. The results also showed that the maximum adsorption was recorded at pH 8 at adsorbent dose of 2.5 g L-1 with the contact time of 120 min. To express the adsorption equilibrium, the results were subjected to Langmuir and Freundlich isotherms and correlation coefficient implies that the adsorption process follows the Freundlich adsorption isotherm. The findings of this study suggest the suitability of the novel FW derived biochar as an effective and low cost adsorbent for the removal of heavy metals form wastewater.

Bio-adsorption of heavy metals from aqueous solution using the ZnO-modified date pits

The bio-adsorption of heavy metals (including Cu2+, Ni2+, and Zn2+) in aqueous solution and also in an industry wastewater using the ZnO-modified date pits (MDP) as the bio-adsorbent are investigated. The fresh and used bio-adsorbents were characterized by FT-IR, SEM, BET, and XRD. The bio-adsorption parameters (including the pH of solution, the particle size of MDP, the shaking speed, the initial concentration of heavy metals, the dosing of MDP, the adsorption time, and the adsorption temperature) were screened and the data were used to optimize the bio-adsorption process and to study the bio-adsorption isotherms, kinetics, and thermodynamics. Two adsorption models (Langmuir isotherm model and Freundlich isotherm model) and three kinetic models (pseudo-first-order model, pseudo-second-order model, and intra-particle diffusion model) were applied to model the experimental data. Results show that the maximum adsorption amount of Cu2+, Ni2+, and Zn2+ on a complete monolayer of MDP are 82.4, 71.9, and 66.3 mg g-1, which are over 4 times of those of date pits-based bio-adsorbents reported in literature. The bio-adsorption of heavy metals on MDP is spontaneous and exothermic, and is regulated by chemical adsorption on the homogeneous and heterogeneous adsorption sites of MDP surface. This work demonstrates an effective modification protocol for improved bio-adsorption performance of the date pits-based bio-adsorbent, which is cheap and originally from a waste.

Advances, challenges, and prospects in microalgal-bacterial symbiosis system treating heavy metal wastewater

Heavy metal (HM) pollution, particularly in its ionic form in water bodies, is a chronic issue threatening environmental security and human health. The microalgal-bacterial symbiosis (MABS) system, as the basis of water ecosystems, has the potential to treat HM wastewater in a sustainable manner, with the advantages of environmental friendliness and carbon sequestration. However, the differences between laboratory studies and engineering practices, including the complexity of pollutant compositions and extreme environmental conditions, limit the applications of the MABS system. Additionally, the biomass from the MABS system containing HMs requires further disposal or recycling. This review summarized the recent advances of the MABS system treating HM wastewater, including key mechanisms, influence factors related to HM removal, and the tolerance threshold values of the MABS system to HM toxicity. Furthermore, the challenges and prospects of the MABS system in treating actual HM wastewater are analyzed and discussed, and suggestions for biochar preparation from the MABS biomass containing HMs are provided. This review provides a reference point for the MABS system treating HM wastewater and the corresponding challenges faced by future engineering practices.

A review on adsorption of heavy metals from wastewater using carbon nanotube and graphene-based nanomaterials

The rampant rise in world population, industrialization, and urbanization expedite the contamination of water sources. The presence of the non-biodegradable character of heavy metals in waterways badly affects the ecological balance. In this modern era, the unavailability of getting clear water as well as the downturn in water quality is a major concern. Therefore, the effective removal of heavy metals has become much more important than before. In recent years, the attention to better wastewater remediation was directed towards adsorption techniques with novel adsorbents such as carbon nanomaterials. This review paper primarily emphasizes the fundamental concepts, structures, and unique surface properties of novel adsorbents, the harmful effects of various heavy metals, and the adsorption mechanism. This review will give an insight into the current status of research in the realm of sustainable wastewater treatment, applications of carbon nanomaterials, different types of functionalized carbon nanotubes, graphene, graphene oxide, and their adsorption capacity. The importance of MD simulations and density functional theory (DFT) in the elimination of heavy metals from aqueous media is also discussed. In addition to that, the effect of factors on heavy metal adsorption such as electric field and pressure is addressed.

Carbonaceous adsorbents in the removal of aquaculture pollutants: A technical review of methods and mechanisms

Carbonaceous adsorbents (CAs) are becoming increasingly popular owing to their low-cost, ease of preparation, and versatility. Meanwhile, aquaculture is becoming a fundamental food industry, globally, due to a wide range of advantages such as economic and nutritional benefits, whilst protecting the depletion of natural resources. However, as with any farming, the technique is known to introduce a plethora of chemicals into the surrounding environment, including antibiotics, nutrients, fertilisers and more. Therefore, the treatment of aquaculture effluent is gaining traction to ensure the sustainable growth of the industry. Although the existing mitigation techniques are somewhat effective, they suffer from degradation of the water quality or harm to local environments/organisms. This article aims to identify the sources and impacts of various aquaculture pollutants. After which the authors will provide an environmentally friendly and novel approach to the treatment of aquaculture effluent using carbonaceous adsorbents. The article will detail discussions about the product life span, including, synthesis, activation, modification, applications in aqueous media, regeneration and End-of-Life (EoL) approaches, with a particular focus on the impacts of competitive adsorption between pollutants and environmental matrices. Some research gaps were also highlighted, such as the lack of literature applying real-world samples, the effects of competitive adsorption and the EoL applications and management for CAs.

Phytotoxicity and cytotoxicity attributes of immobilized Bacillus cereus treated and untreated textile effluents on Vigna mungo seeds and Artemia franciscana larvae

The physicochemical attributes of textile effluents collected from secondary treatment stage was investigated in this study and also assess the biosorption potential of membrane immobilized Bacillus cereus and free form of Bacillus cereus on textile effluent through bioreactor model study to find a sustainable solution to manage the textile effluent as vital need. Furthermore, the phytotoxicity and cytotoxicity nature of treated and untreated textile effluents on Vigna mungo and Artemia franciscana larvae under laboratory conditions as a novel approach. The textile effluent physicochemical parameter analysis results showed that the properties such as colour (Hazen unit), pH, turbidity, As, Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Cd, Cl, Cr, Cu, Hg, Ni, Pb, SO₄^2-, and Zn were beyond the acceptable limits. Bacillus cereus immobilized on a polyethylene membrane eliminated greater amounts of dye (25.0 ± 1.3, 56.5 ± 1.8, 57.18 ± 1.5, and 54.34 ± 1.7 Hazen unit from An1, Ae2, Ve3, and So4 respectively) and pollutants (As: 0.9-2.0, Cd: 6-8, Cr: 300-450, Cu: 5-7, Hg: 0.1-0.7, Ni: 8-14, Pb: 4-5, and Zn: 4-8 mg L^-1) from textile effluent in a week of biosorption investigation using a bioreactor model (batch type) compared to a free form of B. cereus on textile effluent. The phytotoxicity and cytotoxicity study results revealed that the membrane immobilized B. cereus treated textile effluent exposure showed reduced phytotoxicity and minimal cytotoxicity (including mortality) percentage compared with free form B. cereus treated and untreated textile effluents. These entire results conclude that the membrane immobilized B. cereus may considerably minimize/detoxify the harmful pollutants from the textile effluents. A large scale level biosorption approach need to be performed to validate the maximum pollutants removing potential of this membrane immobilized bacteria species and optimal conditions for effective remediation.

Breeding, Biosorption Characteristics, and Mechanism of a Lead-Resistant Strain

To effectively carry out the bioremediation of a Pb²⁺ polluted environment, a lead-tolerant strain named D1 was screened from the activated sludge of a factory in Hefei, and its lead removal in a solution with Pb²⁺ concentration of 200 mg/L could reach 91% under optimal culture conditions. Morphological observation and 16S rRNA gene sequencing were used to identify D1 accurately, and its cultural characteristics and lead removal mechanism were also preliminarily studied. The results showed that the D1 strain was preliminarily identified as the Sphingobacterium mizutaii strain. The experiments conducted via orthogonal test showed that the optimal conditions for the growth of strain D1 were pH 7, inoculum volume 6%, 35 °C, and rotational speed 150 r/min. According to the results of scanning electron microscopy and energy spectrum analysis before and after the D1 exposure to lead, it is believed that the lead removal mechanism of D1 is surface adsorption. The Fourier transform infrared spectroscopy (FTIR) results revealed that multiple functional groups on the surface of the bacterial cells are involved in the Pb adsorption process. In conclusion, the D1 strain has excellent application prospects in the bioremediation of lead-contaminated environments.

Surface Engineering Design of Nano FeS@Stenotrophomonas sp. by Ultrasonic Chemical Method for Efficient U(VI) and Th(IV) Extraction

Nano-FeS has great potential for use in the management of radioactive contaminants. In this paper, we prepared a FeS@Stenotrophomonas sp. composite material by ultrasonic chemistry, and it showed excellent removal of uranium and thorium from the solution. Through optimization of the experimental conditions, it was found that the maximum adsorption capacities for uranium and thorium reached 481.9 and 407.5 mg/g for a composite made with a synthetic ratio of 1:1, pH 5 and 3.5, respectively, for U and Th, and sonication for 20 min. Compared with those of FeS or Stenotrophomonas alone, the removal capacity was greatly improved. The results of a mechanistic study indicated that efficient removal of the uranium and thorium was due to ion exchange, reduction, and microbial surface adsorption. FeS@Stenotrophomonas sp. could be applied to U(VI) and Th(IV) extraction for radioactive water.

A novel and capable supported phenylazophenylenediamine-based nano-adsorbent for removal of the Pb, Cd, and Ni ions from aqueous solutions

Herein, we report the synthesis and characterization of chrysoidine (4-phenylazo-m-phenylenediamine) grafted on magnetic nanoparticles (Fe₃O₄@SiO₂@CPTMS@PhAzPhDA = FeSiPAPDA) as a novel and versatile adsorbent used for the satisfactory removal of Pb, Ni, and Cd ions from contaminated water via the formation of their complexes. The Freundlich, Langmuir, Temkin, and Redlich-Patterson isotherm models were studied to reveal the adsorption capability of the adsorbent and were found out that the Langmuir model is more compatible with the nano-adsorbent behavior. Moreover, according to the ICP tests as well as based on the Langmuir isotherm, the maximum adsorption capacity of the FeSiPAPDA-based adsorbent for the Pb ions (97.58) is more than that of Cd (78.59) and Ni ions (64.03).

The effective removal of Ni2+, Cd2+, and Pb2+ from aqueous solution by adenine-based nano-adsorbent

The presence of heavy metal ions in drinking and wastewater generates environmental and human health concerns as they are known as cumulative poisons. Therefore, the purification of contaminated waters is an important ecological issue. Various techniques have been developed to address this issue, where adsorption has received widespread attention. The facile synthesis of effective adenine-based nano-adsorbents is reported and adsorptive removal of Ni²⁺, Cd²⁺, and Pb²⁺ from aqueous media was investigated by inductively-coupled plasma analyses, adsorption isotherms, kinetics, and thermodynamic studies. The effects of pH, adsorbent dose, contact time, and temperature were optimized. The maximum adsorption capacity was achieved at pH = 7, an adsorbent dose of 25 mg, and an initial concentration of 50 mg L^-1 at 25 °C. A thermodynamic study showed that adsorption is an endothermic process, and the Langmuir model fitted well to the ion adsorption data to reveal that the maximum adsorption capacities for Ni²⁺, Cd²⁺, and Pb²⁺ were 273.7, 252.4, and 249.8 mg g^-1, respectively.

Recent advances in g-C3N4-based photo-enzyme catalysts for degrading organic pollutants

In recent years, photocatalytic reactions have shown great potential in degrading organic pollutants because of their simple operation and no secondary pollution. Graphitic carbon nitride (g-C₃N₄) is one of the most frequently used photocatalyst materials in the field of photocatalysis because it is a form of photocatalytic material with facile synthesis, no metal, visible light response, and strong stability. Enzyme-catalyzed degradation has received extensive attention due to its broad selectivity, high efficiency, and environmental friendliness. Horseradish peroxidase (HRP), one of several oxidoreductases utilized for pollutant degradation, has a wide range of applications due to its mild reaction conditions and high stability. Exploring efficient platforms for immobilizing g-C₃N₄ and HRP to develop photo-enzyme-coupled catalysis is an attractive practical topic. The coupling effect of g-C₃N₄ and HRP improves the carrier separation efficiency and generates more active species, which finally realize the solar-driven non-selective destruction of organic pollutants. We describe the alteration of g-C₃N₄ and the immobilization of HRP in detail in this study, and we outline recent developments in the photo-enzyme coupling of g-C₃N₄ and HRP.

Efficient Adsorption of Chromium Ions from Aqueous Solutions by Plant-Derived Silica

Nowadays, there is great interest in the use of plant waste to obtain materials for environmental protection. In this study, silica powders were prepared with a simple and low-cost procedure from biomass materials such as horsetail and common reed, as well as wheat and rye straws. The starting biomass materials were leached in a boiling HCl solution. After washing and drying, the samples were incinerated at 700 °C for 1 h in air. The organic components of the samples were burned leaving final white powders. These powders were characterized by powder X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, dynamic light scattering (DLS), scanning electron microscopy (SEM), and low-temperature nitrogen sorption. The amorphous powders (biosilica) contained mainly SiO2, as indicated by FTIR analysis. Horsetail-derived silica was chosen for testing the removal of dichromate ions from water solutions. This biosilica had a good ability to adsorb Cr(VI) ions, which increased after modification of the powder with the dodecylamine surfactant. It can be concluded that the applied procedure allowed obtaining high purity biosilica from plant waste with good efficiency. The produced biosilica was helpful in removing chromium ions and showed low cytotoxicity to human endothelial cells, suggesting that it can be safely used in environmental remediation.

Potential applications of spent adsorbents and catalysts: Re-valorization of waste

Water pollution has increased with the growth of human population and its industrial activities. Textile effluents constitute a particular threat due to the presence of heavy metals and dyes. Adsorption is one of the most applied technologies in contaminant removal owing to its high efficiency, low cost, practical implementation and possibility to operate in several experimental conditions. However, this process implies the generation of spent materials, representing a limitation to scale-up. Although the applications of exhausted solids in effluent treatments have not been extensively reviewed before, their reutilization appears to be an environmentally and economically attainable alternative. This work summarizes the potential value of solids post-use. The open literature reports that spent adsorbents based on polysaccharides with iron oxides may adsorb up to 1 g g^-1 of organic pollutants and up to near 100% of metallic ions from wastewater (Cu²⁺, Cd²⁺, Zn²⁺, Pb²⁺). The studied conditions vary from 30 to 60 °C, 0,05 to 6 g L^-1 of adsorbent, 10 mg L^-1 to 250 mg L^-1 of organic pollutants (dyes) and pH between 2 and 8. Spent adsorbents in dye removal have proven to have near 95% efficiency in metallic ion adsorption. Otherwise, the spent solids could be applied to remove Ca²⁺ and Mg²⁺ to decrease the hardness of water. Furthermore, at the end-of-life, these materials could be used in cement and ceramic production. To achieve these aims, it is necessary to design the bioadsorbents and biocatalysts considering not only their primary uses (as adsorbent of organic pollutants), but also secondary applications (as toxic metal or hardness removal) and even their final destination (as additive in ceramic or cement production). Finally, further studies are required on the composition, properties, stability at long-term and the life-cycle cost of these materials when they are applied in the construction industry.

Utilization of Phyllanthus emblica fruit stone as a Potential Biomaterial for Sustainable Remediation of Lead and Cadmium Ions from Aqueous Solutions

In the present work, an effort has been made to utilize Phyllanthus emblica (PE) fruit stone as a potential biomaterial for the sustainable remediation of noxious heavy metals viz. Pb(II) and Cd(II) from the aqueous solution using adsorption methodology. Further, to elucidate the adsorption potential of Phyllanthus emblica fruit stone (PEFS), effective parameters, such as contact time, initial metal concentration, temperature, etc., were investigated and optimized using a simple batch adsorption method. It was observed that 80% removal for both the heavy metal ions was carried out within 60 min of contact time at an optimized pH 6. Moreover, the thermodynamic parameters results indicated that the adsorption process in the present study was endothermic, spontaneous, and feasible in nature. The positive value of entropy further reflects the high adsorbent-adsorbate interaction. Thus, based on the findings obtained, it can be concluded that the biosorbent may be considered a potential material for the remediation of these noxious impurities and can further be applied or extrapolated to other impurities.

Recovery, regeneration and sustainable management of spent adsorbents from wastewater treatment streams: A review

Adsorption is the most widely adopted, effective, and reliable treatment process for the removal of inorganic and organic contaminants from wastewater. One of the major issues with the adsorption-treatment process for the removal of contaminants from wastewater streams is the recovery and sustainable management of spent adsorbents. This review focuses on the effectiveness of emerging adsorbents and how the spent adsorbents could be recovered, regenerated, and further managed through reuse or safe disposal. The critical analysis of both conventional and emerging adsorbents on organic and inorganic contaminants in wastewater systems are evaluated. The various recovery and regeneration techniques of spent adsorbents including magnetic separation, filtration, thermal desorption and decomposition, chemical desorption, supercritical fluid desorption, advanced oxidation process and microbial assisted adsorbent regeneration are discussed in detail. The current challenges for the recovery and regeneration of adsorbents and the methodologies used for solving those problems are covered. The spent adsorbents are managed through regeneration for reuse (such as soil amendment, capacitor, catalyst/catalyst support) or safe disposal involving incineration and landfilling. Sustainable management of spent adsorbents, including processes involved in the recovery and regeneration of adsorbents for reuse, is examined in the context of resource recovery and circular economy. Finally, the review ends with the current drawbacks in the recovery and management of the spent adsorbents and the future directions for the economic and environmental feasibility of the system for industrial-scale application.

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.

Detection and Prediction of HMS from Drinking Water by Analysing the Adsorbents from Residuals Using Deep Learning

Contamination HM is an important issue associated with the environment, and it requires suitable steps for the reduction of HMs in water at an acceptable ratio. With modern technologies, this could be possible by enabling the carbon adsorbents to adsorb the pollutions via deep learning strategies. In this paper, we develop a model on detection and prediction of presence of HMs from drinking water by analysing the adsorbents from residuals using deep learning. The study uses dense neural networks or DenseNets to analyse the microscopic images of the residual adsorbents. The study initially preprocesses and extracts features using standardised procedure. The DenseNets are used finally for detection purpose, and it is trained and tested with standard set of microscopic images. The experimental results are conducted to test the efficacy of the deep learning model on detecting the HM composition. The results of simulation show that the proposed deep learning model achieves 95% higher rate of detecting the HM composition from the adsorption residuals than other methods.

A review on adsorptive separation of toxic metals from aquatic system using biochar produced from agro-waste

Water is a basic and significant asset for living beings. Water assets are progressively diminishing due to huge populace development, industrial activities, urbanization and rural exercises. Few heavy metals include zinc, copper, lead, nickel, cadmium and so forth can easily transfer into the water system either direct or indirect activities of electroplating, mining, tannery, painting, fertilizer industries and so forth. The different treatment techniques have been utilized to eliminate the heavy metals from aquatic system, which includes coagulation/flocculation, precipitation, membrane filtration, oxidation, flotation, ion exchange, photo catalysis and adsorption. The adsorption technique is a better option than other techniques because it can eliminate heavy metals even at lower metal ions concentration, simplicity and better regeneration behavior. Agricultural wastes are low-cost biosorbent and typically containing cellulose have the ability to absorb a variety of contaminants. It is important to note that almost all agro wastes are no longer used in their original form but are instead processed in a variety of techniques to improve the adsorption capacity of the substance. The wide range of adsorption capacities for agro waste materials were observed and almost more than 99% removal of toxic pollutants from aquatic systems were achieved using modified agro-waste materials. The present review aims at the water pollution due to heavy metals, as well as various heavy metal removal treatment procedures. The primary objectives of this research is to include an overview of adsorption and various agriculture based adsorbents and its comparison in heavy metal removal.

Towards a Circular Economy: Analysis of the Use of Biowaste as Biosorbent for the Removal of Heavy Metals

Industrial human activity has led to the release of substantial amounts of heavy metals into the environment. Contamination of water with heavy metals such as lead, cadmium, copper, zinc, chromium, or nickel represents a serious problem. As part of the circular economy, it is appropriate to use biowaste from agriculture, fisheries, and the timber industry as biosorbents. In this literature review, the potential of using these biowaste groups as biosorbents for metal removal is presented. This biowaste is characterized by the presence of carboxyl, hydroxyl, carbonyl, amide, amine, sulfydryl, and other groups on their surface, which form complexes and chelates with metals present in water. Biosorption seems to be a potential alternative to conventional technologies for removing or recovering heavy metals from water or wastewater, which are uneconomical and generate additional waste. The paper demonstrates that harnessing the potential of biowaste to remove metals is beneficial to the environment as they can solve the problem of incineration and realise recycling that meets the circular economy. Although the choice of a suitable biosorbent for the removal of a particular metal involves a lot of research, the high biosorption efficiency, low cost, and renewability justify their use.

Ibuprofen degradation using a Co-doped carbon matrix derived from peat as a peroxymonosulphate activator

The wider presence of pharmaceuticals and personal care products in nature is a major cause for concern in society. Among pharmaceuticals, the anti-inflammatory drug ibuprofen has commonly been found in aquatic and soil environments. We produced a Co-doped carbon matrix (Co-P 850) through the carbonization of Co²⁺ saturated peat and used it as a peroxymonosulphate activator to aid ibuprofen degradation. The properties of Co-P 850 were analysed using field emission scanning electron microscopy, energy filtered transmission electron microscopy and X-ray photoelectron spectroscopy. The characterization results showed that Co/Fe oxides were generated and tightly embedded into the carbon matrix after carbonization. The degradation results indicated that high temperature and slightly acidic to neutral conditions (pH = 5 to 7.5) promoted ibuprofen degradation efficiency in the Co-P 850/peroxymonosulphate system. Analysis showed that approx. 52% and 75% of the dissolved organic carbon was removed after 2 h and 5 h of reaction time, respectively. Furthermore, the existence of chloride and bicarbonate had adverse effects on the degradation of ibuprofen. Quenching experiments and electron paramagnetic resonance analysis confirmed that SO₄^·-, ·OH and O₂^·- radicals together contributed to the high ibuprofen degradation efficiency. In addition, we identified 13 degradation intermediate compounds and an ibuprofen degradation pathway by mass spectrometry analysis and quantum computing. Based on the results and methods presented in this study, we propose a novel way for the synthesis of a Co-doped catalyst from spent NaOH-treated peat and the efficient catalytic degradation of ibuprofen from contaminated water.

Development of Armillae mellea immobilized nanodiamond for the preconcentrations of Cr(III), Hg(II) and Zn(II)

In this study, we present an environmental friend and easy procedure for simultaneous preconcentration of Cr(III), Hg(II) and Zn(II) by solid-phase extraction before their determination by inductively coupled plasma optical emission spectrometry. Armillae mellea immobilized nanodiamond was used as sorbent. During the study, critical parameters influencing the extraction performance were investigated in detail. The best parameters were found as pH 5.0, 2.0 mL min^-1 of flow rate, 200 mg of Armillae mellea, 300 mL of sample volume. LOD values were found as 0.025, 0.13 and 0.038 ng mL^-1, respectively for Cr(III), Hg(II) and Zn(II). By applying the developed procedure, sensitivities of ICP-OES were improved for 60 fold for Cr(III), Hg(II) and Zn(II). Their concentrations in different food samples were measured after microwave digestion and solid-phase extraction.

Removal of copper and/or zinc ions from synthetic solutions by immobilized, non-viable bacterial biomass: Batch and fixed-bed column lab-scale study

A biosorbent composed of non-viable Pseudomonas putida trapped in agar beads was able to remove Cu²⁺ and Zn²⁺ from solutions containing one or both metals. The process in batch followed pseudo second-order kinetics, with adsorption capacities of 0.255 mg Cu²⁺/g and 0.170 mg Zn²⁺/g according to the Langmuir isotherm. These values were up to ten times lower for beads without biomass. The metals became bound to OH, CH₂, CO, COC and COP groups, with the last three being provided by the biomass, which highlights its importance. Adsorption values for single-metal solutions filtered in a fixed-bed column were 0.152 mg Cu²⁺/g and 0.117 mg Zn²⁺/g, but decreased to 0.075 and 0.058, respectively, with mixed-metal solutions (1:1 ratio). In 10:1-ratio solutions, the metal in greater proportion was better adsorbed. Under all conditions, removal percentage was ∼60 %. The column could be reused throughout ten absorption/desorption cycles without significant alterations in adsorption capacity.

Enhanced reductive removal of ciprofloxacin in pharmaceutical wastewater using biogenic palladium nanoparticles by bubbling H2

To treat waste with waste and efficiently remove the organic pollutant, waste palladiums(ii) were adsorbed and reduced on microorganism surface to catalyze the reductive removal of ciprofloxacin in pharmaceutical wastewater. By optimizing conditions such as pH and temperature, the amount of biogenic palladium adsorbed and reduced on E. coli reached 139.48 mg g⁻¹ (Pd/microorganisms). Moreover, most of the Pd(ii) was reduced to nanometer-sized Pd(0) as characterized by TEM and SEM with EDXA. Using the obtained biogenic palladium, the reductive removal of ciprofloxacin is up to 87.70% at 25 °C, 3.03 folds of that achieved in the absence of H₂. The results show that waste E. coli microorganisms can efficiently adsorb and remove waste Pd(ii) and produce Bio-Pd nanoparticle catalysts in the presence of H₂. This biogenic palladium presents high catalytic activity and great advantages in the reductive degradation of ciprofloxacin. Our method can also be applied to other waste metal ions to prepare the biogenic metals, facilitate their recovery and reuse in degrading organic pollutants in wastewater to achieve “treating waste using waste”.

A solution has been successfully introduced to three key challenges from the wastewater containing waste microorganisms, metal and ciprofloxacin, respectively.