Effective heavy metal removal from aqueous systems by thiol functionalized magnetic mesoporous silica

Enhanced capacity of thiol-functionalized sugarcane bagasse and rice husk biochars for arsenite sorption in aqueous solutions

The utilization of biowastes for producing biochar to remove potentially toxic elements from water represents an important pathway for aquatic ecosystem decontamination. Here we explored the significance of thiol-functionalization on sugarcane bagasse biochar (Th/SCB-BC) and rice husk biochar (Th/RH-BC) to enhance arsenite (As(III)) removal capacity from water and compared their efficiency with both pristine biochars (SCB-BC and RH-BC). The maximum As(III) sorption was found on Th/SCB-BC and Th/RH-BC (2.88 and 2.51 mg g-1, respectively) compared to the SCB-BC and RH-BC (1.51 and 1.40 mg g-1). Relatively, a greater percentage of As(III) removal was obtained with Th/SCB-BC and Th/RH-BC (92% and 83%, respectively) at a pH 7 compared to pristine SCB-BC and RH-BC (65% and 55%) at 6 mg L-1 initial As(III) concentration, 2 h contact time and 1 g L-1 sorbent dose. Langmuir (R2 = 0.99) isotherm and pseudo-second-order kinetic (R2 = 0.99) models provided the best fits to As(III) sorption data. Desorption experiments indicated that the regeneration ability of biochars decreased and it was in the order of Th/SCB-BC (88%) > Th/RH-BC (82%) > SCB-BC (77%) > RH-BC (69%) up to three sorption-desorption cycles. Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy results demonstrated that the thiol (-S-H) functional groups were successfully grafted on the surface of two biochars and as such contributed to enhance As(III) removal from water. Spectroscopic data indicated that the surface functional moieties, such as -S-H, - OH, - COOH, and C = O were involved to increase As(III) sorption on thiol-functionalized biochars. This study highlights that thiol-grafting on both biochars, notably on SCB-BC, enhanced their ability to remove As(III) from water, which can be used as an effective technique for the treatment of As from drinking water.

Novel adsorbent for malachite green from okra stalks waste: synthesis, kinetics and equilibrium studies

In this study, malachite green (MG) removal was performed with activated carbon synthesized from okra stalks by microwave assisted chemical activation method. In the synthesis of activated carbon, the effects of gas in the microwave, activation, and impregnation rate were investigated. The synthesized activated carbon characterization was investigated using BET, FT-IR, and SEM analyses. The activated carbon surface area achieved was 759.453 m2 g-1. In addition, the surface area of activated carbon synthesized using the conventional method was17.766 m2 g-1. The effect of the initial solution concentration on MG adsorption was investigated. According to the kinetic and equilibrium data, it was found that the adsorption process best fitted the pseudo-second order kinetic model and the Langmuir isotherm. According to the equilibrium data, the maximum adsorption capacity (qmax) of the monolayer was 119.05 mg g-1. In addition, MG adsorption was investigated by the experimental design method. The adsorption capacity at the determined optimum conditions was 99.63 mg g-1. All results show that activated carbon synthesized from waste biomass by combining the conventional method with microwave-assisted impregnation is a cheap and environmentally friendly adsorbent.

Superior Removal of Vanadium(V) from Simulated Groundwater with a Fe-Based Metal-Organic Framework Immobilized on Cotton Fibers

A suitable adsorbent is essential in the process of removing hazardous vanadium(V) from actual groundwater. In this work, MIL-88A(Fe)/cotton (MC) was employed to eliminate V(V) from simulated vanadium-contaminated groundwater. The findings demonstrated that MC exhibited an exceptional performance in removing V(V), displaying a maximum adsorption capacity of 218.71 mg g-1. MC exhibits great promise as an adsorbent for V(V) elimination in an extensive pH range spanning 3 to 11. Even in the presence of high levels of competing ions such as Cl-, NO3-, and SO42-, MC demonstrated remarkable specificity in adsorbing V(V). The results of column experiments and co-occurring ions influence tests indicate that MC is a potential candidate for effectively treating actual vanadium-contaminated groundwater. The effluent could meet the vanadium content restriction of 50 μg L-1 required in China's drinking water sources. Regeneration of MC can be performed easily without experiencing significant capacity loss. The results obtained from this research indicate the promising potential of MC in mitigating vanadium pollution.

Extraction of heavy metals from wastewater using amine-modified mesoporous silica

Presence of heavy metals in wastewater is a critical environmental issue, and efficient extraction of the metals remains a challenging task. In this study, the adsorption behavior of Ce(III), Hg(II), and Cu(II) metal ions using MCM-48 material modified with acid and base functional groups was examined. The modified materials were characterized using various techniques, including XRD, BET, FT-IR, NMR, and SEM, which revealed that the materials' properties remained unchanged after modification. The adsorption capacity of the modified materials for metal ions was then evaluated and was found that the amine-modified MCM-48 material exhibited the highest adsorption efficiency. Precisely, the amine-modified material achieved an adsorption capacity of 97% for Ce(III), 98% for Hg(II), and 90% for Cu(II) after 180 min of adsorption. These results highlight the effectiveness of amine functionalization in enhancing the adsorption capacity of silica material for heavy metals.

Hydrodynamic Analysis and Cake Erosion Properties of a Modified Water-Based Drilling Fluid by a Polyacrylamide/Silica Nanocomposite during Rotating-Disk Dynamic Filtration

In this study, the potential of using a polyacrylamide-silica nanocomposite (PAM-S) to control the filtration properties of bentonite water-based drilling muds under different salinity conditions was evaluated. Static filtration tests under low-pressure/low-temperature (LPLT) conditions accompanied by rheological measurements have been carried out to analyze the role of silica nanoparticles (NPs) and nanocomposites (NCs) in the base fluid properties. Moreover, high-pressure/high-temperature (HPHT) static filtration was also investigated to evaluate the thermal stability of PAM-S. Afterward, dynamic filtration has been conducted in a filtration cell equipped with an agitating system with a disk-type impeller to investigate the hydrodynamic and formation of a filter cake under shear flow conditions. Fluid flow velocity and wall shear stress (WSS) distribution over the filter cake were analyzed using an exact 3D computational fluid dynamic (CFD) simulation. A transparent filtration cell with a camera was used to accurately record the fluid flow field inside the filter press and validate the CFD results. The obtained results indicated that adding silica NPs at a concentration of less than 2 wt % increases the fluid loss due to reducing rheological properties such as yield point. While silica NPs could not significantly change the mud properties, the experimental results showed that, under both LPLT and HPHT conditions, the PAM-S NC could reduce the total filtration loss by 70% at a low concentration of 0.75 wt %. Moreover, during dynamic filtration, the results indicated that there is a linear relationship between the cake thickness and the inverse of WSS at different operating pressures. However, no correlation could be found between predeposited mud cake erosion and WSS. At a rotating disk speed of 1000 rpm, more than 60% of the predeposited mud cake was eroded after 30 min for a saline mud sample while for the NC-treated mud sample cake erosion is considerably reduced and reaches up to 20% at 1.5 wt % PAM-S.

Polyacrylonitrile/Aminated Polymeric Nanosphere Nanofibers as Efficient Adsorbents for Cr(VI) Removal

In this work, polyacrylonitrile/aminated polymeric nanosphere (PAN/APN) nanofibers were prepared by electrospinning of monodispersed aminated polymeric nanospheres (APNs) for removal of Cr(VI) from aqueous solution. Characterization results showed that obtained PAN/APNs possessed nitrogen functionalization. Furthermore, the adsorption application results indicated that PAN/APN nanofibers exhibited a high adsorption capacity of 556 mg/g at 298 K for Cr(VI) removal. The kinetic data showed that the adsorption process fits the pseudo-second order. A thermodynamic study revealed that the adsorption of Cr(VI) was spontaneous and endothermic. The coexisting ions Na⁺, Ca²⁺, K⁺, Cl⁻, NO₃⁻ and PO₄³⁻ had little influence on Cr(VI) adsorption, while SO₄²⁻ in solution dramatically decreased the removal performance. In the investigation of the removal mechanism, relative results indicated that the adsorption behavior possibly involved electrostatic adsorption, redox reaction and chelation. PAN/APN nanofibers can detoxify Cr(VI) to Cr(III) and subsequently chelate Cr(III) on its surface. The unique structure and nitrogen functionalization of PAN/APN nanofibers make them novel and prospective candidates in heavy metal removal.

Removal of Thallium from Aqueous Solutions by Adsorption onto Alumina Nanoparticles

Thallium (I) was removed from aqueous solution by using gamma-alumina nanoparticles (γANPs) materials as nano adsorbents. Varied experimental conditions such as adsorbent dose, agitation time, initial concentration, pH, and temperature effects were carried out in batch conditions in view of the optimization of thallium (I) adsorption and the identification of the adsorption mechanisms in the system γANPs-Tl. The pH effect indicated a remarkable increase in the quantity of Tl(I) removed for pH values ranging from 4 to 8, an almost constant magnitude for pH values between 8 and 10, and a decrease for pH values above 10. Considering an initial Tl(I) concentration of 20 µg/L and an adsorbent dose of 1 g/L at a pH value of 8.5, the removal was achieved at 95.12 ± 0.02% efficiency. The pseudo-second-order kinetics and the Freundlich isotherm perfectly described the adsorption mechanism. The process of thallium (I) adsorption reaction, as highlighted by thermodynamic investigations, was found to be spontaneous and exothermic with coexistence of physisorption and chemisorption with a dominance of physisorption. The diffusion model predicted multi-linearity, suggesting an involvement of surface spread and intraparticle diffusion in the sorption process. Thallium removal was effective by using γANPs as nano adsorbents.

One-pot alkanolamines-assisted synthesis of magnetic mesoporous silica for synthetic dye adsorption

Magnetic mesoporous silica (MMS) was synthesized in a one-pot system using various alkanolamines (triethanolamine, diethanolamine, tris (hydroxymethyl)aminomethane) as a basic catalyst. The characterization of the composites was conducted using scanning electron microscope, transmission electron microscope, X-ray diffractometer, surface area analyzer, and X-ray photoelectros spectroscopy. The MMS synthesized with tris(hydroxymethyl)aminomethane (MMS_TRIS) showed the highest specific surface area, pore volume, and average pore diameter. However, when the composites were applied as adsorbents for brilliant green (BG) dye, MMS synthesized with diethanolamine (MMS_DEA) showed the highest maximum adsorption capacity of 339.7 mg g^-1. The fastest adsorption rate constant of 1.57 × 10^-2 g mg^-1 min^-1 was obtained for MMS_TRIS, which has the largest average pore size among all composites. The adsorption kinetic study suggested that the adsorption of BG onto the prepared MMS composites was mainly chemisorption process, which most likely involves electrostatic interaction and hydrogen bonding between BG molecule and the surface of the composites.

Structure-Property Relationship for Different Mesoporous Silica Nanoparticles and its Drug Delivery Applications: A Review

Mesoporous silica nanoparticles (MSNs) are widely used as a promising candidate for drug delivery applications due to silica’s favorable biocompatibility, thermal stability, and chemical properties. Silica’s unique mesoporous structure allows for effective drug loading and controlled release at the target site. In this review, we have discussed various methods of MSNs’ mechanism, properties, and its drug delivery applications. As a result, we came to the conclusion that more in vivo biocompatibility studies, toxicity studies, bio-distribution studies and clinical research are essential for MSN advancement.

Raptopoulou C, Psycharis V, Konidaris KF, Chasapis CT, Perlepes SP. Confirming the Molecular Basis of the Solvent Extraction of Cadmium(II) Using 2-Pyridyl Oximes through a Synthetic Inorganic Chemistry Approach and a Proposal for More Efficient Extractants

The present work describes the reactions of CdI2 with 2-pyridyl aldoxime (2paoH), 3-pyridyl aldoxime (3paoH), 4-pyridyl aldoxime (4paoH), 2-6-diacetylpyridine dioxime (dapdoH2) and 2,6-pyridyl diamidoxime (LH4). The primary goal was to contribute to understanding the molecular basis of the very good liquid extraction ability of 2-pyridyl ketoximes with long aliphatic chains towards toxic Cd(II) and the inability of their 4-pyridyl isomers for this extraction. Our systematic investigation provided access to coordination complexes [CdI2(2paoH)2] (1), {[CdI2(3paoH)2]}n (2), {[CdI2(4paoH)2]}n (3) and [CdI2(dapdoH2)] (4). The reaction of CdI2 and LH4 in EtOH resulted in a Cd(II)-involving reaction of the bis(amidoxime) and isolation of [CdI2(L'H2)] (5), where L'H2 is the new ligand 2,6-bis(ethoxy)pyridine diimine. A mechanism of this transformation has been proposed. The structures of 1, 2, 3, 4·2EtOH and 5 were determined by single-crystal X-ray crystallography. The complexes have been characterized by FT-IR and FT-Raman spectra in the solid state and the data are discussed in terms of structural features. The stability of the complexes in DMSO was investigated by 1H NMR spectroscopy. Our studies confirm that the excellent extraction ability of 2-pyridyl ketoximes is due to the chelating nature of the extractants leading to thermodynamically stable Cd(II) complexes. The monodentate coordination of 4-pyridyl ketoximes (as confirmed in our model complexes with 4paoH and 3paoH) seems to be responsible for their poor performance as extractants.

Heavy Metal Adsorption Using Magnetic Nanoparticles for Water Purification: A Critical Review

Research on contamination of groundwater and drinking water is of major importance. Due to the rapid and significant progress in the last decade in nanotechnology and its potential applications to water purification, such as adsorption of heavy metal ion from contaminated water, a wide number of articles have been published. An evaluating frame of the main findings of recent research on heavy metal removal using magnetic nanoparticles, with emphasis on water quality and method applicability, is presented. A large number of articles have been studied with a focus on the synthesis and characterization procedures for bare and modified magnetic nanoparticles as well as on their adsorption capacity and the corresponding desorption process of the methods are presented. The present review analysis shows that the experimental procedures demonstrate high adsorption capacity for pollutants from aquatic solutions. Moreover, reuse of the employed nanoparticles up to five times leads to an efficiency up to 90%. We must mention also that in some rare occasions, nanoparticles have been reused up to 22 times.

Differentiating Nanomaghemite and Nanomagnetite and Discussing Their Importance in Arsenic and Lead Removal from Contaminated Effluents: A Critical Review

Arsenic and lead heavy metals are polluting agents still present in water bodies, including surface (lake, river) and underground waters; consequently, the development of new adsorbents is necessary to uptake these metals with high efficiency, quick and clean removal procedures. Magnetic nanoparticles, prepared with iron-oxides, are excellent candidates to achieve this goal due to their ecofriendly features, high catalytic response, specific surface area, and pulling magnetic response that favors an easy removal. In particular, nanomagnetite and maghemite are often found as the core and primary materials regarding magnetic nanoadsorbents. However, these phases show interesting distinct physical properties (especially in their surface magnetic properties) but are not often studied regarding correlations between the surface properties and adsorption applications, for instance. Thus, in this review, we summarize the main characteristics of the co-precipitation and thermal decomposition methods used to prepare the nano-iron-oxides, being the co-precipitation method most promising for scaling up processes. We specifically highlight the main differences between both nano-oxide species based on conventional techniques, such as X-ray diffraction, zero and in-field Mössbauer spectroscopy, X-ray photoelectron spectroscopy, X-ray absorption spectroscopy, and X-ray magnetic circular dichroism, the latter two techniques performed with synchrotron light. Therefore, we classify the most recent magnetic nanoadsorbents found in the literature for arsenic and lead removal, discussing in detail their advantages and limitations based on various physicochemical parameters, such as temperature, competitive and coexisting ion effects, i.e., considering the simultaneous adsorption removal (heavy metal-heavy metal competition and heavy metal-organic removal), initial concentration, magnetic adsorbent dose, adsorption mechanism based on pH and zeta potential, and real water adsorption experiments. We also discuss the regeneration/recycling properties, after-adsorption physicochemical properties, and the cost evaluation of these magnetic nanoadsorbents, which are important issues, but less discussed in the literature.

Crown-Ether-Modified SBA-15 for the Adsorption of Cr(VI) and Zn(II) from Water

Recently, the release of some metal ions to the environment has been observed to cause serious damages to human health and the environment. Herein, a chromium(VI)- and zinc(II)-selective adsorbent (CB18crown6/SBA-15) was successfully fabricated through the covalent attachment of 4′-carboxybenzo-18-crown-6 (CB18crown6) as a ligand on mesoporous silica support (SBA-15). The CB18crown6/SBA-15 adsorbent was characterized by Fourier-transform infrared (FTIR) spectrometry, X-ray diffraction (XRD), N₂ adsorption–desorption, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). To evaluate its ability to selectively capture Cr(VI) and Zn(II), adsorption experiments were conducted. The influences of pH, initial concentration of metal ions, and coexisting metal ions on the adsorption process were examined. The CB18crown6/SBA-15 selectively adsorbed Cr(VI) at pH 2 and Zn(II) at pH 5, respectively, from the mixed aqueous solutions of chromium, zinc, lithium, cadmium, cobalt, strontium, and cesium ions. The data for the adsorption of Cr(VI) onto the CB18crown6/SBA-15 were well explained by the Langmuir adsorption isotherm. In addition, the recycling and reuse of CB18crown6/SBA-15 was successfully achieved, and 71 and 76% reuse efficiency of Cr(VI) and Zn(II), respectively, was obtained after five cycles. This study suggests that the use of the CB18crown6/SBA-15 can be a feasible approach for the selective remediation of Cr(VI) and Zn(II) contamination.

Efficient Activation of Coal Fly Ash for Silica and Alumina Leaches and the Dependence of Pb(II) Removal Capacity on the Crystallization Conditions of Al-MCM-41

In this study, four different coal fly ashes (CFAs) were used as raw materials of silica and alumina for the preparation of the alumina-containing Mobil Composition of Matter No. 41 (Al-MCM-41) and the exploration of an activation strategy that is efficient and universal for various CFAs. Alkaline hydrothermal and alkaline fusion activations proceeded at different temperatures to determine the best treatment parameters. We controlled the pore structure and surface hydroxyl density of the CFA-derived Al-MCM-41 by changing the crystallization temperature and aging time. The products were characterized by small-angle X-ray diffraction, nitrogen isotherms, Fourier-transform infrared spectroscopy, 29Si silica magic-angle spinning nuclear magnetic resonance, and transmission electron microscopy, and they were then grafted with thiol groups to remove Pb(II) from aqueous solutions. This paper innovatively evaluates the CFA activation strategies using energy consumption analysis and determines the optimal activation methodology and parameters. This paper also unveils the effect of the crystallization condition of Al-MCM-41 on its subsequent Pb(II) removal capacity. The results show that the appropriate selection of crystallization parameters can considerably increase the removal capacity over Pb(II), providing a new path to tackle the ever-increasing concern of aquic heavy-metal pollution.

Easily Processable, Highly Transparent and Conducting Thiol-Functionalized Reduced Graphene Oxides Langmuir-Blodgett Films

We report synthesis and fabrication of highly thionated reduced graphene oxide and its Langmuir-Blodgett (LB) film without an LB trough. As the synthesized product, mercapto reduced graphene oxide (mRGO) contains high thiol content estimated from XPS, corresponding to a surface coverage of 1.3 SH/nm². The mRGO LB film shows two electronic transport properties, following Efros-Shklovskii variable-range hopping (VRH) and Mott VRH at low and high temperature, respectively. Optical and band gap of the LB film was estimated from Tauc plot and semi-logarithmic-scale plot of sheet resistance versus temperature to be 0.6 and 0.1 eV, respectively. Additionally, the sheet resistance of the mRGO LB film depends on the quantity of the thiol functional group with the same transmittance at 550 nm (500 kΩ for mRGO, 1.3 MΩ for tRGO with 92% transmittance).

Amphiphilic Thiol Polymer Nanogel Removes Environmentally Relevant Mercury Species from Both Produced Water and Hydrocarbons

Technologies for removal of mercury from produced water and hydrocarbon phases are desired by oil and gas production facilities, oil refineries, and petrochemical plants. Herein, we synthesize and demonstrate the efficacy of an amphiphilic, thiol-abundant (11.8 wt % S, as thiol) polymer nanogel that can remove environmentally relevant mercury species from both produced water and the liquid hydrocarbon. The nanogel disperses in both aqueous and hydrocarbon phases. It has a high sorption affinity for dissolved Hg(II) complexes and Hg-dissolved organic matter complexes found in produced water and elemental (Hg⁰) and soluble Hg-alkyl thiol species found in hydrocarbons. X-ray absorption spectroscopy analysis indicates that the sorbed mercury is transformed to a surface-bound Hg(SR)₂ species in both water and hydrocarbon regardless of its initial speciation. The nanogel had high affinity to native mercury species present in real produced water (>99.5% removal) and in natural gas condensate (>85% removal) samples, removing majority of the mercury species using only a 50 mg L^-1 applied dose. This thiolated amphiphilic polymeric nanogel has significant potential to remove environmentally relevant mercury species from both water and hydrocarbon at low applied doses, outperforming reported sorbents like sulfur-impregnated activated carbons because of the mass of accessible thiol groups in the nanogel.

Multifunctional Binding Sites on Nitrogen-Doped Carboxylated Porous Carbon for Highly Efficient Adsorption of Pb(II), Hg(II), and Cr(VI) Ions

Heavy metal ions represent one of the most toxic and environmentally harmful pollutants of water sources. This work reports the development of a novel chelating nitrogen-doped carboxylated porous carbon (ND-CPC) adsorbent for the effective removal of the heavy metal ions Pb(II), Hg(II), and Cr(VI) from contaminated and polluted water sources. The ND-CPC adsorbent is designed to combine four different types of nitrogen functional groups (graphitic, pyrrolic, pyridinic, and pyridine oxide) with the carboxylic acid functional groups within a high surface area of 1135 ± 20 m²/g of the porous carbon structure. The ND-CPC adsorbent shows exceptionally high adsorption affinity for Pb(II) with a capacity of 721 ± 14 mg/g in addition to high uptake values of 257 ± 5 and 104 ± 2 mg/g for Hg(II) and Cr(VI), respectively. The high adsorption capacity is also coupled with fast kinetics where the equilibrium time required for the 100% removal of Pb(II) from 50 ppb and 10 ppm concentrations is 30 s and 60 min, respectively. Even with the very high concentration of 700 ppm, 74% uptake of Pb(II) is achieved within 90 min. Removal efficiencies of 100% of Pb(II), 96% of Hg(II), 91% of Cu(II), 82% of Zn(II), 25% of Cd(II), and 13% of Ni(II) are achieved from a solution containing 10 ppm concentrations of these ions, thus demonstrating excellent selectivity for Pb(II), Hg(II), and Cu(II) ions. Regeneration of the ND-CPC adsorbent shows excellent desorption efficiencies of 99 and 95% for Pb(II) and Cr(VI) ions, respectively. Because of the fast adsorption kinetics, high removal capacity and excellent regeneration, stability, and reusability, the ND-CPC is proposed as a highly efficient remediation adsorbent for the solid-phase removal of Pb(II), Hg(II), and Cr(VI) from contaminated water.

Melamine-based functionalized graphene oxide and zirconium phosphate for high performance removal of mercury and lead ions from water

Heavy metal ions are highly toxic and widely spread as environmental pollutants. This work reports the development of two novel chelating adsorbents, based on the chemical modifications of graphene oxide and zirconium phosphate by functionalization with melamine-based chelating ligands for the effective and selective extraction of Hg(ii) and Pb(ii) from contaminated water sources. The first adsorbent melamine, thiourea-partially reduced graphene oxide (MT-PRGO) combines the heavier donor atom sulfur with the amine and triazine nitrogen's functional groups attached to the partially reduced GO nanosheets to effectively capture Hg(ii) ions from water. The MT-PRGO adsorbent shows high efficiency for the extraction of Hg(ii) with a capacity of 651 mg g-1 and very fast kinetics resulting in a 100% removal of Hg(ii) from 500 ppb and 50 ppm concentrations in 15 second and 30 min, respectively. The second adsorbent, melamine zirconium phosphate (M-ZrP), is designed to combine the amine and triazine nitrogen's functional groups of melamine with the hydroxyl active sites of zirconium phosphate to effectively capture Pb(ii) ions from water. The M-ZrP adsorbent shows exceptionally high adsorption affinity for Pb(ii) with a capacity of 681 mg g-1 and 1000 mg g-1 using an adsorbent dose of 1 g L-1 and 2 g L-1, respectively. The high adsorption capacity is also coupled with fast kinetics where the equilibrium time required for the 100% removal of Pb(ii) from 1 ppm, 100 ppm and 1000 ppm concentrations is 40 seconds, 5 min and 30 min, respectively using an adsorbent dose of 1 g L-1. In a mixture of six heavy metal ions at a concentration of 10 ppm, the removal efficiency is 100% for Pb(ii), 99% for Hg(ii), Cd(ii) and Zn(ii), 94% for Cu(ii), and 90% for Ni(ii) while at a higher concentration of 250 ppm the removal efficiency for Pb(ii) is 95% compared to 23% for Hg(ii) and less than 10% for the other ions. Because of the fast adsorption kinetics, high removal capacity, excellent regeneration, stability and reusability, the MT-PRGO and M-ZrP are proposed as top performing remediation adsorbents for the solid phase extraction of Hg(ii) and Pb(ii), respectively from contaminated water.

Fabrication of abamectin-loaded mesoporous silica nanoparticles by emulsion-solvent evaporation to improve photolysis stability and extend insecticidal activity

Mesoporous silica nanoparticles (MSNs) can be designed to effectively load, protect, and control the release of pesticides. In this study, emulsion-solvent evaporation was used to fabricate abamectin-loaded MSNs. Our method could deliver abamectin in the process of MSN self-assembly, resulting in simple operation, short preparation period, and outstanding drug carrying capacity. The characteristics of abamectin-loaded MSNs, including morphology, loading content, stability against photolysis, controlled release behavior, and toxicological effect, were systematically investigated. Abamectin-loaded MSNs were successfully produced, having spherical shape, rough surface, uniform particle sizes, typically hollow structure, high loading efficiency (44.8%), excellent photodegradation-reducing ability, and controlled-release properties. The biological activity survey for abamectin-loaded MSNs showed excellent toxicological properties against Plutella xylostella larvae, and maintained biological activity until the 15th day, with 70% mortality of the target insect. The results of this study are beneficial for the development of a delivery system for the rational and effective usage of pesticides.

Dual-Functional Redox-Responsive Nanocarriers for Loading Phytohormone and Complexation with Heavy Metal Ions

This work focused on designing a novel redox-responsive nanocarrier synthesized from carboxymethyl-β-cyclodextrin-modified nanosilica, which could load and release plant hormones, such as salicylic acid (SA), in plant cells. When the SA-loaded nanoparticles cross the plant cell wall, the disulfide bond can be broken to form sulfhydryl groups under the action of reduced glutathione (GSH), thus releasing SA. Meanwhile, the resulting thiol groups exhibited strong affinity toward several heavy metal ions, mercury ions in particular, thus playing a role similar to phytochelatins for detoxification. The results of SA release in vitro proved that the release proceeded much faster in GSH-rich than in GSH-free environments. The adsorption behaviors of the redox-responsive nanoparticles toward heavy metal ions, after phytohormones release, were systematically investigated. Moreover, the synergetic effects on sustained release and metal ion capture enable the redox-responsive cyclodextrin-modified silica to be an effective and dual-functional nanocarrier that has great potential for agricultural applications.

The Nanosized Dye Adsorbents for Water Treatment

Clean water is a vital element for survival of any living creature and, thus, crucially important to achieve largely and economically for any nation worldwide. However, the astonishingly fast trend of industrialization and population growth and the arisen extensive water pollutions have challenged access to clean water across the world. In this regard, 1.6 million tons of dyes are annually consumed. Thereof, 10%–15% are wasted during use. To decolorize water streams, there is an urgent need for the advanced remediation approaches involving utilization of novel materials and technologies, which are cost and energy efficient. Nanomaterials, with their outstanding physicochemical properties, can potentially resolve the challenge of need to water treatment in a less energy demanding manner. In this review, a variety of the most recent (from 2015 onwards) opportunities arisen from nanomaterials in different dimensionalities, performances, and compositions for water decolorization is introduced and discussed. The state-of-the-art research studies are presented in a classified manner, particularly based on structural dimensionality, to better illustrate the current status of adsorption-based water decolorization using nanomaterials. Considering the introduction of many newly developed nano-adsorbents and their classification based on the dimensionality factor, which has never been employed for this sake in the related literature, a comprehensive review will be presented.

Size and distribution of the iron oxide nanoparticles in SBA-15 nanoporous silica via SANS study

Structural characteristics of nanocomposite series consisting of iron oxide nanoparticles (NPs) embedded in the regular pores of amorphous silica matrix (SBA-15) were investigated by means of small angle neutron scattering (SANS). By virtue of unique neutron properties, insight into the inner structure and matter organization of this kind of systems was facilitated for the first time. Based on rigorous experimental support, fundamental model describing the neutron scattering intensity distribution was proposed by assuming general composite structural features. Model application to SANS data confirmed the presence of iron oxide NPs in the body of examined matrices, providing additional information on their shape, concentration and size distribution. Scattering superposition principle employed in the model conception allows for tailoring its fundamental characteristics, and renders it a potent and versatile tool for a wide range of applications.

Efficient immobilization of ionic corrosion products by a silica-hydroxyapatite composite via a cold sintering route

We have successfully demonstrated a new method of radioactive waste immobilization by hosting a waste-bearing form in another waste matrix. A cold sintering route was used to consolidate a silica-incorporated hydroxyapatite (Si-HAp) composite at 200 °C by applying a uniaxial pressure of 500 MPa for a short holding time of 10 min. The higher relative sintered density of up to 98.0 ± 1.3% was achieved by 25 wt% Si loaded HAp. Results from high resolution X-ray diffraction, micro-hardness, and high resolution scanning electron microscopy confirmed the densification with good mechanical strength (micro-hardness = 2.9 ± 0.3 GPa). For practical applications, two kinds of wastes (25 wt% ionic corrosion product-sorbed EDTA functionalized mesoporous silica and 75 wt% ionic corrosion product-sorbed HAp) were mixed, consolidated and tested. The chemical stability of the solidified composite matrix was positively assessed for low leaching rates of 5.9 × 10^-9 to 1.2 × 10^-5 g per m² per day using a standard product consistency test. The consolidated composite can bear compressive stress up to 358 MPa, which is orders of magnitude higher than the waste acceptance criteria of 3.5 MPa. The low process temperature can make this sintering process very powerful for the immobilization of radionuclides with volatility and low boiling point. Such a low temperature solidified matrix hosting various wastes may be a promising path for waste management because of its simplicity, reliability, scalability, cost effectiveness and environmental friendliness.

Amino- and Thiol- Polysilsesquioxane Simultaneously Coating on Poly(p-Phenylenetherephthal Amide) Fibers: Bifunctional Adsorbents for Hg(II)

A double reagents simultaneous functionalization (DRSF) was used to prepare porous polysilsesquioxane with NH₂ and SH bifunctional groups (PAMPSQ) coated poly(p-phenylenetherephthal amide) (PPTA) fibers adsorbents (PPTA-AM), via in situ condensations with aminopropyltriethoxysilane (APTES) and mercaptopropyltriethoxysilane (MPTES). The PAMPSQ coated on the PPTA surface was in the form of nanoparticles and its morphology varied with the proportion of the reactants. The PAMPSQ exhibited loose open meso- or macroporous features. The functional groups utilization of PAMPSQ was much higher than those of polysilsesquioxane on the mono-functional adsorbents with thiol or amino groups. The selective adsorption of PPTA-AM adsorbents for Hg(II) in binary component metal ion systems indicated their potential application in environmental remediation. The adsorption mechanism of Hg(II) onto PPTA-AM was proposed.

Advanced Filtration Membranes for the Removal of Perfluoroalkyl Species from Water

Perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) are two perfluoroalkyl substances that have been shown to result in several adverse health effects, including birth defects, kidney/testicular cancer, as well as liver and thyroid damage. The surfactant nature of PFOS and PFOA in water makes these compounds extremely difficult to remove from drinking water. In this paper, an efficient method to remove PFOS and PFOA from drinking water using linear fluorinated silane-functionalized aluminum oxide hydroxide (γ-AlOOH) nanowhiskers was developed. Filters functionalized with linear fluorinated silanes containing 13-17 fluorine atoms were able to remove >90% of the PFOS/PFOA at a very high flux of 1223 L/m²·h. However, due to the hydrophobicity of these linear fluorinated silanes, high pressure drop was also noted across the membrane thickness during the filtration process. To reduce the back-pressure drop, linear fluorinated silanes with appended hydrophilic poly(ethylene glycol) units were synthesized, and it was further demonstrated that the new hydrophilic linear fluorinated silane dramatically reduced the pressure drop of the γ-AlOOH filter while maintaining 99.9% PFOS and PFOA reduction. Adsorption tests were performed to understand the removal mechanism.

Multifunctional Binding Chemistry on Modified Graphene Composite for Selective and Highly Efficient Adsorption of Mercury

Engineering of multifunctional binding chemistry on graphene composites using thiol-ene click reaction for selective and highly efficient adsorption of mercury(II) is demonstrated. Graphene oxide (GO) is used as an initial material for covalent attachment of cysteamine molecules by thiol-ene click reaction on C═C groups to achieve a partially reduced graphene surface with multiple binding chemistry such as O, S, and N. Batch adsorption studies showed remarkable adsorption rate with only 1 mg L^-1 dosage of adsorbent used to remove 95% Hg (II) (∼1.5 mg L^-1) within 90 min. The high adsorption capacity of 169 ± 19 mg g^-1, high selectivity toward Hg in the presence of 30 times higher concentration of competing ions (Cd, Cu, Pb) and high regeneration ability (>97%) for five consecutive adsorption-desorption cycles were achieved. Comparative study with commercial activated carbon using spiked Hg (II) river water confirmed the high performance and potential of this adsorbent for real mercury remediation of environmental and drinking waters.

Novel magnetic graphene oxide functionalized cyanopropyl nanocomposite as an adsorbent for the removal of Pb(II) ions from aqueous media: equilibrium and kinetic studies

This work presents the synthesis of the novel silica-cyanopropyl functionalized magnetic graphene oxide (MGO/SiO₂-CN) hybrid nanomaterial derived by sol-gel method as a cheap efficient magnetic sorbent for the removal of extremely hazardous lead ions from aqueous media. The integration of the magnetic property, the carbon substrate, and the nitrile (-C ≡ N) containing organic grafted silica matrix promoted the adsorption capability against lead ions along with its simple synthesis recovery and low cost. The prepared nanocomposite was comprehensively characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. Adsorption of lead was found to be pH dependent because of the charged nature of both analyte and adsorbent surface. Adsorption experiments were conducted under the optimum conditions, and the obtained experimental data from atomic absorption spectroscopy were analyzed using the popular isothermal models namely Langmuir, Freundlich, and Dubinin-Radushkevich isotherms as well as kinetically studied and evaluated for adsorption standard free energy (E). The experimental results have demonstrated the enhanced adsorption capability of the proposed sorbent nanocomposite for lead ion removal with the maximum adsorption capacity of 111.11 mg/g at pH 5.0. The proposed mechanism of lead adsorption was mainly attributed to the complexation of lead positive ions with the grafted -C ≡ N bond. The synergistic effect of the combination of three components (i.e., the magnetic graphene oxide matrix, the triple bond containing organic moiety, and the inorganic porous silica framework) excelled the adsorption capability and proved to be a good candidate as adsorbent for the removal of lead ions.

Protection of Thiol Groups on the Surface of Magnetic Adsorbents and Their Application for Wastewater Treatment

The magnetite nanoparticles were functionalized with silica shells bearing mercaptopropyl (monofunctional) and mercaptopropyl-and-alkyl groups (bifunctional) by single-step sol-gel technique. The influence of synthetic conditions leading to increased amounts of active functional groups on the surface and improved capacity in the uptake of Ag(I), Cd(II), Hg(II), and Pb(II) cations was revealed. The physicochemical properties of obtained magnetic nanocomposites were investigated by FTIR, Raman, XRD, TEM, SEM, low-temperature nitrogen ad-/desorption measurements, TGA, and chemical microanalysis highlighting the efficiency of functionalization and mechanisms of the preparation procedures. The removal of the main group of heavy metal cations was studied in dependence from the pH, contact time and equilibrium concentration to analyze the complexes composition for the large scale production of improved adsorbents. It was demonstrated that introduction of the alkyl groups into the surface layer prevents the formation of the disulfide bonds between adjacent thiol groups. The obtained adsorbents were employed to treat real wastewater from Ruskov, Slovakia with concentration of Fe 319 ng/cm3, Cu 23.7 ng/cm3, Zn 36 ng/cm3, Mn 503 ng/cm3, Al 21 ng/cm3, As 34 ng/cm3, Pb 5.8 ng/cm3, Ni 35 ng/cm3, Co 4.2 ng/cm3, Cr 9.4 ng/cm3, Sb 6 ng/cm3, Cd 5 ng/cm3. These materials proved to be highly effective in the removal of 50% of all metal ions, espeсially Zn, Cd, and Pb ions from it and turned recyclable, opening for their sustainable use in water purification.

In-Situ Fixation of All-Inorganic Mo-Fe-S Clusters for the Highly Selective Removal of Lead(II)

The selective adsorption by suitable substrate materials is considered one of the most economical methods. In this work, an all-inorganic bimetallic Mo-Fe-S cluster is facilely achieved through in situ chemical fixation of tetrathiomolybdate (TTM) on Fe₃O₄ nanoparticles (NPs) at room temperature (donated as FeMoS NPs). The bimetallic building blocks on the obtained FeMoS NPs possess a monovacancy species of sulfur, endowing FeMoS NPs with a selectivity order of Zn²⁺, Mn²⁺, Ni²⁺ < Cd²⁺ ≪ Cu²⁺ < Pb²⁺ for metal-ion adsorption, a novel application for the Mo-Fe-S clusters. Particularly, with the highest selectivity for Pb²⁺ (K_d ≈ 10⁷), which is about 3 × 10³-1 × 10⁶ times higher than those for other ions and has exceeded that of a series of outstanding sorbents reported for Pb²⁺, FeMoS NPs can efficiently reduce the concentration of Pb²⁺ from ∼10 ppm to an extremely low level of ∼1 ppb. This facile and rational fabrication of the Mo-Fe-S cluster with Fe₃O₄ represents a feasible approach to cheaply develop novel and efficient materials for the selective removal of lead(II).

Thin silica shell coated Ag assembled nanostructures for expanding generality of SERS analytes

Surface-enhanced Raman scattering (SERS) provides a unique non-destructive spectroscopic fingerprint for chemical detection. However, intrinsic differences in affinity of analyte molecules to metal surface hinder SERS as a universal quantitative detection tool for various analyte molecules simultaneously. This must be overcome while keeping close proximity of analyte molecules to the metal surface. Moreover, assembled metal nanoparticles (NPs) structures might be beneficial for sensitive and reliable detection of chemicals than single NP structures. For this purpose, here we introduce thin silica-coated and assembled Ag NPs (SiO2@Ag@SiO2 NPs) for simultaneous and quantitative detection of chemicals that have different intrinsic affinities to silver metal. These SiO2@Ag@SiO2 NPs could detect each SERS peak of aniline or 4-aminothiophenol (4-ATP) from the mixture with limits of detection (LOD) of 93 ppm and 54 ppb, respectively. E-field distribution based on interparticle distance was simulated using discrete dipole approximation (DDA) calculation to gain insight into enhanced scattering of these thin silica coated Ag NP assemblies. These NPs were successfully applied to detect aniline in river water and tap water. Results suggest that SiO2@Ag@SiO2 NP-based SERS detection systems can be used as a simple and universal detection tool for environment pollutants and food safety.

Application of Iron Oxide Nanomaterials for the Removal of Heavy Metals

In the 21st century water polluted by heavy metal is one of the environment problems. Various methods for removal of the heavy metal ions from the water have extensively been studied. Application of iron oxide nanaparticles based nanomaterials for removal of heavy metals is well-known adsorbents for remediation of water. Due to its important physiochemical property, inexpensive method and easy regeneration in the presence of external magnetic field make them more attractive toward water purification. Surface modification strategy of iron oxide nanoparticles is also used for the remediation of water increases the efficiency of iron oxide for the removal of the heavy metal ions from the aqueous system.

A modified nanoporous stir bar for simultaneous determination of Cu(II) and Cd(II) ions in natural samples prior to flame atomic absorption spectroscopy

In this work, the application of stir bar sorptive extraction (SBSE), as a fast and conventional method, has been investigated for the simultaneous preconcentration and determination of trace amounts of Cd(II) and Cu(II) ions in natural samples. For this purpose, the surface of stir bar was functionalized by amine functionalized nanoporous silica and characterized by IR spectroscopy, X-ray powder diffraction (XRD), Atomic force microscopy (AFM) and N2adsorption. In this approach, after the preconcentration of Cd(II) and Cu(II) ions and removing the matrix interferences using modified stir bar, the amounts of these ions were determined in eluent by flame atomic absorption spectroscopy (FAAS). Various parameters on adsorption and elution steps including pH of sample, adsorption kinetic, eluent parameters (type, volume and concentration) and elution time, have been optimized in this study. The limits of detection (LOD) were 1.6 and 13.8 ng mL-1(recovery of 83.5 and 88.1%) for cadmium and copper ions, respectively. The preconcentration factors were 133 and 137 and the relative standard deviations (RSD) of the method were 5.7 and 4.6% for Cd(II) and Cu(II) ions, respectively. As the key point in this study seems to be stir bar nanoporous structure, the analytical performance of this stir bar was compared to non-porous ones. The accuracy of this novel method has been confirmed using some standard references materials. Finally the potential of this method was investigated by determination of Cd(II) and Cu(II) ions in some real samples with complicated matrixes.

Synergistic removal of Pb(II), Cd(II) and humic acid by Fe3O4@mesoporous silica-graphene oxide composites

The synergistic adsorption of heavy metal ions and humic acid can be very challenging. This is largely because of their competitive adsorption onto most adsorbent materials. Hierarchically structured composites containing polyethylenimine-modified magnetic mesoporous silica and graphene oxide (MMSP-GO) were here prepared to address this. Magnetic mesoporous silica microspheres were synthesized and functionalized with PEI molecules, providing many amine groups for chemical conjugation with the carboxyl groups on GO sheets and enhanced the affinity between the pollutants and the mesoporous silica. The features of the composites were characterized using TEM, SEM, TGA, DLS, and VSM measurements. Series adsorption results proved that this system was suitable for simultaneous and efficient removal of heavy metal ions and humic acid using MMSP-GO composites as adsorbents. The maximum adsorption capacities of MMSP-GO for Pb(II) and Cd (II) were 333 and 167 mg g⁻¹ caculated by Langmuir model, respectively. HA enhances adsorption of heavy metals by MMSP-GO composites due to their interactions in aqueous solutions. The underlying mechanism of synergistic adsorption of heavy metal ions and humic acid were discussed. MMSP-GO composites have shown promise for use as adsorbents in the simultaneous removal of heavy metals and humic acid in wastewater treatment processes.