Photodegradation of ethyl paraben using simulated solar radiation and Ag3PO4 photocatalyst

Photocatalytic degradation of parabens: A comprehensive meta-analysis investigating the environmental remediation potential of emerging pollutant

The increasing prevalence of paraben compounds in the environment has given rise to concerns regarding their detrimental impacts on both ecosystems and human health. Over the past few decades, photocatalytic reactions have drawn significant attention as a method to accelerate the otherwise slow degradation of these pollutants. The current study aims to evaluate the current efficacy of the photocatalytic method for degrading parabens in aqueous solutions. An extensive literature review and bibliometric analysis were conducted to identify key research trends and influential areas in the field of photocatalytic paraben degradation. Studies were screened based on the predetermined inclusion and exclusion criteria, which led to 13 studies that were identified as being appropriate for the meta-analysis using the random effects model. Furthermore, experimental parameters such as pH, paraben initial concentration, catalyst dosage, light intensity, and contact time have been reported to have key impacts on the performance of the photocatalytic degradation process. A comprehensive quantitative assessment of these parameters was carried out in this work. Overall, photocatalytic techniques could eliminate parabens with an average degradation efficiency of >80 %. The findings of the Egger's test and the Begg's test were statistically not significant suggesting potential publication bias was not observed. This review provides a holistic understanding of the photocatalytic degradation of parabens and is anticipated to encourage more widespread adoption of photocatalytic procedures as a suitable method for the elimination of parabens from aqueous solutions, opening new avenues for future research in this direction.

Green chromatographic methods for determination of co-formulated lidocaine hydrochloride and miconazole nitrate along with an endocrine disruptor preservative and potential impurity

Recently, green analytical chemistry (GAC) is a key issue towards the idea of sustainability, the analytical community is focused on developing analytical methods that incorporate green chemistry principles to minimize adverse impacts on the environment and humans. Herein, we present 2 sustainable, selective, and validated chromatographic methods. Initially, lidocaine hydrochloride (LDC) and miconazole nitrate (MIC) with two preservatives; methyl paraben (MTP) and saccharin sodium (SAC) were chromatographed via TLC-densitometric method which employed ethyl acetate: methanol: formic acid (9:1:0.1, by volume) as the mobile phase with UV detection at 220.0 nm, good correlation was obtained in the range of 0.3-3.0 µg/band for MIC and LDC. Following that, RP-HPLC was successfully applied for separating quinary mixture of LDC, MIC, MTP, SAC along with LDC impurity; dimethyl aniline (DMA) using C18 column, and a gradient green mobile phase composed of methanol and phosphate buffer (pH 6.0) in different ratios with a flow rate 1.5 mL/min and UV detection at 210.0 nm, linearity ranges from 1.00 to 100.00 µg/mL for MIC, 2.00-100.00 µg/mL for LDC and 1.00--20.00 µg/mL for MTP and DMA. No records to date regarding the determination of the two drugs, besides MTP and DMA. The proposed methods were validated according to the ICH guidelines and applied successfully to the analysis of the compounds. The methods' results were statistically compared to those obtained by applying the reported one, indicating no significant difference regarding both accuracy and precision. The methods' greenness profiles have been assessed and compared with those of the reported method using different assessment tools.

Heat-activated persulfate for the degradation of micropollutants in water: A comprehensive review and future perspectives

This work is a critical review of the most important studies that have dealt with heat-activated persulfate to degrade persistent micropollutants in the last six years. The effect of the different operating parameters is discussed, wherein in all cases, the efficiency was favored at higher temperatures and oxidant concentrations. Particular emphasis was given to the effect of the aqueous matrix. Since heat activation is a homogeneous process based on the production of free radicals, in most of the studies presented, the removal of pollutants decreases as the complexity of the aqueous matrix increases except in cases where secondary oxidative species are produced that are selective with specific pollutants. It has also been observed that the change in toxicity usually follows the removal of the parent compound despite the formation of several by-products. Nowadays, combining different processes for the simultaneous activation of persulfate seems to be gaining ground. A hybrid process is an interesting strategy to reduce costs and increase efficiency, especially in real wastewater. In this light, the most interesting studies of hybrid systems for the destruction of micropollutants in recent years based on thermally activated persulfate are also summarized. Finally, some steps are proposed for future research towards the industrial application, including the study of chemical mixtures, the integrated toxicity assessment, the examination of simultaneous disinfection and decomposition of pollutants into real wastewater, the estimation of the required costs, and energy the combination of processes and their coupling with renewable sources, and the design of pilot plants and the scale-up of the hybrid processes.

Ag3PO4-Deposited TiO2@Ti3C2 Petals for Highly Efficient Photodecomposition of Various Organic Dyes under Solar Light

Two-dimensional Ti₃C₂ MXenes can be used to fabricate hierarchical TiO₂ nanostructures that are potential photocatalysts. In this study, the photodecomposition of organic dyes under solar light was investigated using flower-like TiO₂@Ti₃C₂, deposited using narrow bandgap Ag₃PO₄. The surface morphology, crystalline structure, surface states, and optical bandgap properties were determined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption analysis, and UV-Vis diffuse reflectance spectroscopy (UV-DRS). Overall, Ag₃PO₄-deposited TiO₂@Ti₃C₂, referred to as Ag₃PO₄/TiO₂@Ti₃C₂, demonstrated the best photocatalytic performance among the as-prepared samples, including TiO₂@Ti₃C₂, pristine Ag₃PO₄, and Ag₃PO₄/TiO₂ P25. Organic dyes, such as rhodamine B (RhB), methylene blue (MB), crystal violet (CV), and methylene orange (MO), were efficiently degraded by Ag₃PO₄/TiO₂@Ti₃C₂. The significant enhancement of photocatalysis by solar light irradiation was attributed to the efficient deposition of Ag₃PO₄ nanoparticles on flower-like TiO₂@Ti₃C₂ with the efficient separation of photogenerated e-/h+ pairs, high surface area, and extended visible-light absorption. Additionally, the small size of Ag₃PO₄ deposition (ca. 4–10 nm diameter) reduces the distance between the core and the surface of the composite, which inhibits the recombination of photogenerated charge carriers. Free radical trapping tests were performed, and a photocatalytic mechanism was proposed to explain the synergistic photocatalysis of Ag₃PO₄/TiO₂@Ti₃C₂ under solar light.

Ag3PO4-based photocatalysts and their application in organic-polluted wastewater treatment

Semiconductor photocatalysis technology has shown great potential in the field of organic pollutant removal, as it can use clean and pollution-free solar energy as driving force. The discovery of silver phosphate (Ag₃PO₄) is a major breakthrough in the field of visible light responsive semiconductor photocatalysis due to its robust capacity to absorb visible light < 520 nm. Furthermore, the holes produced in Ag₃PO₄ under light excitation possess a strong oxidation ability. However, the strong oxidation activity of Ag₃PO₄ is only achieved in the presence of electron sacrifice agents. Otherwise, photocorrosion would greatly reduce the reuse efficiency of Ag₃PO₄. This review thus focuses on the structural characteristics and preparation methods of Ag₃PO₄. Particularly, the recent advances in noble metal deposition, ion doping, and semiconductor coupling, as well as methods of magnetic composite modification for the improvement of catalytic activity and recycling efficiency of Ag₃PO₄-based catalysts, were also discussed, and all of these measures could enhance the catalytic performance of Ag₃PO₄ toward organic pollutants degradation. Additionally, some potential modification methods for Ag₃PO₄ were also proposed. This review thus provides insights into the advantages and disadvantages of the application of Ag₃PO₄ in the field of photocatalysis, clarifies the photocorrosion essence of Ag₃PO₄, and reveals the means to improve photocatalytic activity and stability of Ag₃PO₄. Furthermore, it provides a theoretical and methodological basis for studying Ag₃PO₄-based photocatalyst and also compiles valuable information regarding the photocatalytic treatment of organic polluted wastewater.

Removal of drug losartan in environmental aquatic matrices by heat-activated persulfate: Kinetics, transformation products and synergistic effects

In this study, the oxidative degradation of losartan (LOS), a widely administered medicine for high blood pressure by heat-activated persulfate was investigated. Increased temperature and persulfate concentration, as well as acidic conditions enhance the degradation efficiency of LOS, whose rate follows pseudo-first order kinetics. From the respective apparent rate constants in the range 40-60 °C, an apparent activation energy of 112.70 kJ/mol was computed. Radical scavenging tests demonstrated that both HO^• and [Formula: see text] contribute towards LOS degradation. LOS degradation was suppressed in real water matrices including bottled water (BW) and secondary wastewater effluent (WW), while other experiments indicated that the presence of bicarbonates and humic acid negatively affected its oxidation. Instead, the addition of chloride ions at 250 mg/L resulted in a positive effect on LOS removal. The combination of heat-activated PS with low-frequency ultrasound exhibited a synergistic effect, with the ratio S being 2.29 in BW and 1.52 in WW. Five transformation products of LOS were identified through HRMS suspect and non-target screening approaches, among which two are reported for the first time. Using the in-house risk assessment program, ToxTrAMs was revealed that most of the identified TPs present higher toxicity than LOS against Daphnia magna.

Toxicity and removal of parabens from water: A critical review

Parabens are biocides used as preservatives in food, cosmetics and pharmaceuticals. They possess antibacterial and antifungal activity due to their ability to disrupt cell membrane and intracellular proteins, and cause changes in enzymatic activity of microbial cells. Water, one of our most valuable natural resource, has become a huge reservoir for parabens. Halogenated parabens from chlorination/ozonation of water contaminated with parabens have shown to be even more persistent in water than other types of parabens. Unfortunately, there is dearth of data on their (halogenated parabens) presence and fate in groundwater which serves as a major source of drinking water for a huge population in developing countries. An attempt to neglect the presence of parabens in water will expose man to it through ingestion of contaminated food and water. Although there are reviews on the occurrence, fate and behaviour of parabens in the environment, they largely omit toxicity and removal aspects. This review therefore, presents recent reports on the acute and chronic toxicity of parabens, their estrogenic agonistic and antagonistic activity and also their relationship with antimicrobial resistance. This article further X-rays several techniques that have been employed for the removal of parabens in water and their drawbacks including adsorption, biodegradation, membrane technology and advanced oxidation processes (AOPs). The heterogeneous photocatalytic process (one of the AOPs) appears to be more favoured for removal of parabens due to its ability to mineralize parabens in water. However, more work is needed to improve this ability of heterogeneous photocatalysts. Perspectives that will be relevant for future scientific studies and which will drive policy shift towards the presence of parabens in our drinking waters are also offered. It is hoped that this review will elicit some spontaneous actions from water professionals, scientists and policy makers alike that will provide more data, effective technologies, and adaptive policies that will address the growing threat of the presence of parabens in our environment with respect to human health.

The degradation of paraben preservatives: Recent progress and sustainable approaches toward photocatalysis

Parabens are a class of compounds primarily used as antimicrobial preservatives in pharmaceutical products, cosmetics, and foodstuff. Their widely used field leads to increasing concentrations detected in various environmental matrices like water, soil, and sludges, even detected in human tissue, blood, and milk. Treatment techniques, including chemical advanced oxidation, biological degradation, and physical adsorption processes, have been widely used to complete mineralization or to degrade parabens into less complicated byproducts. All kinds of processes were reviewed to give a completed picture of parabens removal. In light of these treatment techniques, advanced photocatalysis, which is emerging rapidly and widely as an economical, efficient, and environmentally-friendly technique, has received considerable attention. TiO₂-based and non-TiO₂-based photocatalysts play an essential role in parabens degradation. The effect of experimental parameters, such as the concentration of targeted parabens, concentration of photocatalyst, reaction time, and initial solution pH, even the presence of radical scavengers, are surveyed and compared from the literature. Some representative parabens such as methylparaben, propylparaben, and benzylparaben have been successfully studied the reaction pathways and their intermediates in their degradation process. As reported in the literature, the degradation of parabens involves the production of highly reactive species, mainly hydroxyl radicals. These reactive radicals would attack the paraben preservatives, break, and finally mineralize them into simpler inorganic and nontoxic molecules. Concluding perspectives on the challenges and opportunities for photocatalysis toward parabens remediation are also intensively highlighted.

Solar light induced photocatalytic removal of sulfamethoxazole from water and wastewater using BiOCl photocatalyst

The photocatalytic activity of bismuth oxychloride (BiOCl) toward sulfamethoxazole (SMX) elimination was investigated. BiOCl was synthesized according to a simple method using thiourea. Its physicochemical characteristics were determined by nitrogen physisorption, X-Ray diffraction, diffuse reflectance spectroscopy, scanning electron microscopy and transmission electron microscopy. Simulated solar irradiation and 1 g/L BiOCl, could effectively remove 0.5 mg/L SMX in less than 90 min. An increase in SMX concentration from 0.25 mg/L to 4 mg/L decreased the observed kinetic constant. Concerning the pH effect, it was found that under alkaline conditions SMX removal was slightly hindered. The water matrix's influence on SMX removal was explored, carrying out experiments in real water matrices, (bottled water (BW) and secondary effluent (WW)). Interestingly SMX removal was not practically altered in WW secondary effluent, but it was slightly hindered in BW bottled water. Experiments, performed in synthetic matrices, revealed that the presence of bicarbonates and chlorides slightly slowed down degradation kinetics, while humic acid enhanced SMX removal at concentrations up to 10 mg/L. Finally, an enhancement on SMX degradation was observed in the presence of persulfate. Quenching experiments of potential reactive species revealed that SMX degradation takes place mainly through reaction with hydroxyl radicals and photogenerated electrons.

Paraben Compounds—Part II: An Overview of Advanced Oxidation Processes for Their Degradation

Water scarcity represents a problem for billions of people and is expected to get worse in the future. To guarantee people’s water needs, the use of “first-hand water” or the reuse of wastewater must be done. Wastewater treatment and reuse are favorable for this purpose, since first-hand water is scarce and the economic needs for the exploration of this type of water are increasing. In wastewater treatment, it is important to remove contaminants of emerging concern, as well as pathogenic agents. Parabens are used in daily products as preservatives and are detected in different water sources. These compounds are related to different human health problems due to their endocrine-disrupting behavior, as well as several problems in animals. Thus, their removal from water streams is essential to achieve safe reusable water. Advanced Oxidation Processes (AOPs) are considered very promising technologies for wastewater treatment and can be used as alternatives or as complements of the conventional wastewater treatments that are inefficient in the removal of such contaminants. Different AOP technologies such as ozonation, catalytic ozonation, photocatalytic ozonation, Fenton’s, and photocatalysis, among others, have already been used for parabens abatement. This manuscript critically overviews several AOP technologies used in parabens abatement. These treatments were evaluated in terms of ecotoxicological assessment since the resulting by-products of parabens abatement can be more toxic than the parent compounds. The economic aspect was also analyzed to evaluate and compare the considered technologies.

Paraben Compounds—Part I: An Overview of Their Characteristics, Detection, and Impacts

Parabens are widely used in different industries as preservatives and antimicrobial compounds. The evolution of analytical techniques allowed the detection of these compounds in different sources at µg/L and ng/L. Until today, parabens were already found in water sources, air, soil and even in human tissues. The impact of parabens in humans, animals and in ecosystems are a matter of discussion within the scientific community, but it is proven that parabens can act as endocrine disruptors, and some reports suggest that they are carcinogenic compounds. The presence of parabens in ecosystems is mainly related to wastewater discharges. This work gives an overview about the paraben problem, starting with their characteristics and applications. Moreover, the dangers related to their usage were addressed through the evaluation of toxicological studies over different species as well as of humans. Considering this, paraben detection in different water sources, wastewater treatment plants, humans and animals was analyzed based on literature results. A review of European legislation regarding parabens was also performed, presenting some considerations for the use of parabens.

Degradation of methylparaben by sonocatalysis using a Co-Fe magnetic carbon xerogel

The degradation of methylparaben (MP) through 20 kHz ultrasound coupled with a bimetallic Co-Fe carbon xerogel (CX/CoFe) was investigated in this work. Experiments were performed at actual power densities of 25 and 52 W/L, catalyst loadings of 12.5 and 25 mg/L, MP concentrations between 1 and 4.2 mg/L and initial pH values between 3 and 10 in ultrapure water (UPW). Matrix effects were studied in bottled water (BW) and secondary treated wastewater (WW), as well as in UPW spiked with bicarbonate, chloride or humic acid. The pseudo-first order kinetics of MP degradation increase with power and catalyst loading and decrease with MP concentration and matrix complexity; moreover, the reaction is also favored at near-neutral conditions and in the presence of dissolved oxygen. The contribution of the catalyst is synergistic to the sonochemical degradation of MP and the extent of synergy is quantified to be >45%. This effect was ascribed to the ability of CX/CoFe to catalyze the dissociation of hydrogen peroxide, formed through water sonolysis, to hydroxyl radicals. Experiments in UPW spiked with an excess of tert-butanol (radical scavenger), sodium dodecyl sulfate or sodium acetate (surfactants) led to substantially decreased rates (i.e. by about 8 times), thus implying that the liquid bulk and the gas-liquid interface are major reaction sites. The stability of CX/CoFe was shown by performing reusability cycles employing magnetic separation of the catalyst after the treatment stage. It was found that the CX/CoFe catalyst can be reused in up to four successive cycles without noteworthy variation of the overall performance of the sonocatalytic process.

Photocatalytic ozonation of parabens mixture using 10% N-TiO2 and the effect of water matrix

Nitrogen-doped TiO₂ was applied in photocatalytic ozonation reactions for the degradation of a mixture of five parabens under UVA radiation, being evaluated the influence of the reaction medium. The initial mixture parabens concentration considered in these experiments was 50 mg L^-1. The parabens degradation rate was considerably enhanced under neutral pH, specially using a buffered solution, leading to a complete removal under 60 min and with transferred ozone dose (TOD) 36% lower compared to reaction under natural conditions. Isopropanol, known radical scavenger, impeded the complete contaminants removal, affecting the reaction route and by-products formation, but when KI was jointly added, total removal was achieved under 30 min and with a TOD of 25.9 mg L^-1. Parabens depletion was also improved in the presence of Cl^-, SO₄^2- and HCO₃^-, commonly present in wastewaters. The use of river water (RW) and a secondary wastewater (SWW) as water matrices maintained the process efficiency with lower TOD required, and treated solutions presented lower phytotoxicity towards Lepidium sativum.

Effect of ultrasound irradiation combined with ozone pretreatment on the anaerobic digestion for the biosludge exposed to trace-level levofloxacin: Degradation, microbial community and ARGs analysis

Anaerobic digestion, the principal method of stabilizing biosolids in wastewater treatment plants (WWTPs), can efficiently and largely attenuate the antibiotic resistances in biosludge. This study aims to investigate the effect of oxidative pretreatment with ultrasound irradiation combined with ozone (US/O₃) on the mesophilic and thermophilic anaerobic digestion (MAD and TAD) for the biosludge bearing trace fluoroquinolones contaminants-levofloxacin (LEVO) which was widely used in recent years. During the oxidation, the trace-level LEVO was almost completely degraded. The methanogenic activity in US/O₃ pretreated TAD dosed 0.1 mg/L LEVO was much higher than those in single MAD and TAD, therefore leading to a remarkable increase in biogas production. The identification of levofloxacin intermediates during chemical degradation was analyzed using LCMS technique and the reaction pathway based on them was proposed. Hydroxyl radicals provided by US/O₃ contributed to oxidative ring opening of LEVO as well as degradation of other biomacromolecules in the biosludge. Besides, the quinoline resistance genes-qnrA and qnrS declined significantly by 1-2 orders of magnitude in US/O₃-pretreated TAD, indicating that the active radicals produced by US/O₃ oxidized and degraded LEVO and therefore inactivated the antibiotic resistant bacteria or genes in the biosolids. Meanwhile, the composition and structure of the microbial community altered and the diversity and richness of total bacterial and potential human pathogens decreased, the pattern of which was correlated with LEVO-resistant genes. Among the well-known AD-related phylum including Bacteroidetes, Firmicutes, Methanobacteria as well as Thermotogae which has been previously detected in TAD and performed organic hydrolysis and degradation, the potential LEVO-resistant bacteria were probably affiliated to Actinobacteria, Bacteroidetes, Proteobacteria, Thermotogae. This study revealed the contribution of US/O₃ pretreatment to the anaerobic digestion in terms of ARGs reduction for trace-LEVO- exposed biosludge and could provide useful guidance for controlling the dissemination of ARB and ARGs in sewage sludge.

Hydrothermal Synthesis of rGO-TiO2 Composites as High-Performance UV Photocatalysts for Ethylparaben Degradation

A series of reduced graphene oxide-TiO2 composites (rGO-TiO2) were prepared by hydrothermal treatment using graphite and titanium isopropoxide as raw materials. The structural, surface, electronic, and optical properties of the prepared composites were extensively characterized by N2 adsorption, FTIR, XRD, XPS, Raman spectroscopy, and DRS. GO was found to be effectively reduced and TiO2 to be in pure anatase phase in all composites obtained. Finally, experiments were performed to evaluate the effectiveness of these new materials as photocatalysts in the degradation of ethylparaben (EtP) by UV radiation. According to the band-gap energies obtained (ranging between 3.09 eV for 4% rGO-TiO2 to 2.55 eV for 30% rGO-TiO2), the rGO-TiO2 composites behave as semiconductor materials. The photocatalytic activity is highest with a rGO content of 7 wt% (7% rGO-TiO2), being higher than observed for pure TiO2 (Eg = 3.20 eV) and achieving 98.6% EtP degradation after only 40 min of treatment. However, the degradation yield decreases with higher percentages of rGO. Comparison with rGO-P25 composites showed that a better photocatalytic performance in EtP degradation is obtained with synthesized TiO2 (rGO-TiO2), probably due to the presence of the rutile phase (14.1 wt %) in commercial P25.

Synthesis of BiOBr/Ag3PO4 heterojunctions on carbon-fiber cloth as filter-membrane-shaped photocatalyst for treating the flowing antibiotic wastewater

Numerous nanosized photocatalysts have been demonstrated to treat antibiotic solutions efficiently in beakers, but plenty of antibiotics have been discharged to the flowing rivers. For photocatalytically degrading the flowing antibiotic wastewater, the prerequisite is to develop flexible large-scale filter-membrane with high photocatalytic activity. To solve this issue, with carbon fiber (CF) cloth as a flexible porous substrate, herein we have reported the in-situ growth of BiOBr/Ag₃PO₄ heterostructures. BiOBr nanosheets (thickness: ~10 nm, diameter: 0.5-1 μm) and Ag₃PO₄ particles (size: 50-200 nm) are synthesized on CF cloth successively via a solvothermal-chemical deposition two-step strategy. CF/BiOBr/Ag₃PO₄ cloth displays excellent visible photoabsorption (edge: ~520 nm). Under visible-light illumination, CF/BiOBr/Ag₃PO₄ cloth (4 × 4 cm²) could degrade ~90.0% tetracycline hydrochloride (TCH) as a model of antibiotics in 30 min in a beaker. Especially, CF/BiOBr/Ag₃PO₄ cloth can be used as the filter-membrane to construct multiple photocatalytic-setup for degrading the flowing antibiotic wastewater. The removal efficiency of TCH goes up from 12.8% at the first grade to 89.6% at the sixth grade. Furthermore, the photocatalytic mechanism of CF/BiOBr/Ag₃PO₄ cloth and the possible decomposition pathway of TCH have been proposed based on simulation and experiment results. Therefore, the present work provides some insight for developing flexible filter-membrane-shaped photocatalysts for degrading the flowing wastewater.

Ag2CO3-halloysite nanotubes composite with enhanced removal efficiency for water soluble dyes

The release of water soluble dyes into the environment is an utmost concern in many countries. This paper presents the effects of Ag₂CO₃-halloysite composites on the efficient removal of water soluble dyes. In this study, NaHCO₃ solution was added dropwisely to halloysite nanotubes (HNTs) dispersed in aqueous AgNO₃ to form Ag₂CO₃-HNTs composite. The synthesized Ag₂CO₃-HNTs composite was characterized with Diffused Reflectance Spectroscopy (DRS), X-ray Diffraction (XRD), Thermogravimetric analysis (TGA), Scanning Electron Microscopy-Energy Dispersive Spectroscopy (SEM-EDX) and Fourier Transform Infra-Red (FT-IR) spectroscopy. The photocatalytic activity and the adsorption capacity of Ag₂CO₃-HNTs on methylene blue and rhodamine b dyes were dependent on pH and the amount of HNTs used in the synthesis. The photodegradation efficiency of Ag₂CO₃ was lower when compared with that of the composite material. This observation is due to the reduction in the electron-hole recombination with the HNTs acting as electron trapping site and the enhanced aqueous dispersity of Ag₂CO₃-HNTs. The enhanced adsorption of water soluble dyes by the Ag₂CO₃-HNTs resulted from the electrostatic attraction of cationic dyes to the surface of the HNTs (negatively charged). The Ag₂CO₃-HNTs therefore removed dye pollutants through a combination of photocatalytic and adsorption processes. The results obtained during the study confirmed the potential application of Ag₂CO₃-HNTs composite in water treatment technologies.

Study of the influence of the matrix characteristics over the photocatalytic ozonation of parabens using Ag-TiO2

Parabens are widely used as antimicrobial and preservative in pharmaceutical and personal products. Their presence has been detected in rivers and wastewater treatment plants. Photocatalytic ozonation process using a low amount of 0.1 wt% Ag-TiO₂ proved to be efficient on the degradation of a mixture of five parabens using a low transferred ozone dose (TOD). The pH effect was analyzed under acidic and neutral conditions. Also, the effect of hydroxyl radical scavenger on parabens degradation and on by-products formation was discussed. Hydroxyl radical present a significant role over parabens degradation and also on by-products formation. The reaction mechanism was analyzed using municipal wastewater as a matrix to infer about the behavior of the process at actual conditions. Municipal wastewater as a matrix clearly enhanced the parabens degradation when compared with the case where ultrapure water was used. In fact, the TOD required for total parabens degradation is lowered 10-20 mg/L of TOD. Therefore, to understand the main responsible species for this improvement, the effects of several ions naturally present in wastewater (HCO₃^-, Cl^- and SO₄^2-) were tested. According to the results it seems that sulfate radical improves the process, while chloride and bicarbonate radicals decrease the process efficiency. In terms of toxicity the luminescence inhibition for Vibrio fischeri was analyzed. The inhibition significantly decreased for treated spiked municipal wastewater.

Transesterification of para-hydroxybenzoic acid esters (parabens) in the activated sludge

Hydrolysis is generally considered as the main pathway for the degradation of ester-type pollutants in aquatic environments. In this study, we found that when methanol or ethanol presented as the external carbon in the activated sludge, transesterification is very important for the degradation of para-hydroxybenzoic acid esters (parabens). In the activated sludge solutions with 1% methanol added, contribution of transesterification to the degradation of the propyl substituted paraben (PrP) and ethyl substituted paraben (EtP) accounted for 46% and 83%, respectively, in the early stage of the reaction. This indicates that in aquatic environments with alcohols presence, parabens prefer to form small molecule homologues than hydrolysis to acid. The predominant transesterification in the activated sludge is related to enzyme preference. Amano lipase from Pseudomonas fluorescens was verified to catalyze hydrolysis and transesterification of parabens, while the latter was dominant in water solution with 1% methanol or ethanol. Considering the common application of small molecular alcohols as the external carbon sources in wastewater treatment plants, transesterification might be an important pathway for the degradation of parabens pollutants in these engineering aquatic environments.

Tuning the Bandgap of Photo-Sensitive Polydopamine/Ag3PO4/Graphene Oxide Coating for Rapid, Noninvasive Disinfection of Implants

Bacterial infection and associated complications are threats to human health especially when biofilms form on biomedical devices and artificial implants. Herein, a hybrid polydopamine (PDA)/Ag3PO4/graphene oxide (GO) coating is designed and constructed to achieve rapid bacteria killing and eliminate biofilms in situ. By varying the amount of GO in the hybrid coating, the bandgap can be tuned from 2.52 to 2.0 eV so that irradiation with 660 nm visible light produces bacteria-killing effects synergistically in concert with reactive oxygen species (ROS). GO regulates the release rate of Ag+ to minimize the cytotoxicity while maintaining high antimicrobial activity, and a smaller particle size enhances the yield of ROS. After irradiation with 660 nm visible light for 15 min, the antimicrobial rates of the PDA/Ag3PO4/GO hybrid coating against Escherichia coli and Staphylococcus aureus are 99.53% and 99.66%, respectively. In addition, this hybrid coating can maintain a repeatable and sustained antibacterial efficacy. The released Ag+ and photocatalytic Ag3PO4 produce synergistic antimicrobial effects in which the ROS increases the permeability of the bacterial membranes to increase the probability of Ag+ to enter the cells to kill them together with ROS synergistically.

Facile Synthesis and Characterization of Ag₃PO₄ Microparticles for Degradation of Organic Dyestuffs under White-Light Light-Emitting-Diode Irradiation

This study demonstrated facile synthesis of silver phosphate (Ag₃PO₄) photocatalysts for the degradation of organic contaminants. Ag₃PO₄ microparticles from different concentrations of precursor, AgNO₃, were produced and characterized by scanning electron microscopy, powder X-ray diffraction, and UV–visible diffuse reflectance spectroscopy. Degradation rates of methylene blue (MB) and phenol were measured in the presence of microparticles under low-power white-light light-emitting-diode (LED) irradiation and the reaction rate followed pseudo-first-order kinetics. The prepared Ag₃PO₄ microparticles displayed considerably high photocatalytic activity (>99.8% degradation within 10 min). This can be attributed to the microparticles’ large surface area, the low recombination rate of electron–hole pairs and the higher charge separation efficiency. The practicality of the Ag₃PO₄ microparticles was validated by the degradation of MB, methyl red, acid blue 1 and rhodamine B under sunlight in environmental water samples, demonstrating the benefit of the high photocatalytic activity from Ag₃PO₄ microparticles.

Graphene: A new activator of sodium persulfate for the advanced oxidation of parabens in water

Graphene was successfully employed as a catalyst for the activation of sodium persulfate, towards the effective degradation of propylparaben, an emerging micro-pollutant, representative of the parabens family. A novel process is proposed which utilizes a commercial graphene nano-powder as the catalyst and sodium persulfate as the oxidizing agent. It was found that over 95% of micro-pollutant degradation occurs within 15 min of reaction time. The effects of catalyst loading (75 mg/L to 1 g/L), sodium persulfate (SPS) concentration (10 mg/L to 1 g/L), initial solution pH (3-9) and initial paraben concentration (0.5 mg/L to 5 mg/L) were examined. Experiments were carried out in different aqueous conditions, including ultrapure water, bottled water and wastewater in order to investigate their effect on the degradation rate. The efficiency of the process was lower at complex water matrices signifying the role of organic matter as scavenger of the oxidant species. The role of radical scavengers was also investigated through the addition of methanol and tert-butanol in several concentrations, which was found to be important only in relatively high values. An experiment in which propylparaben was substituted by methylparaben was conducted and similar results were obtained. The consumption of SPS was found to be high in all pH conditions tested, surpassing 80% in near neutral environment. However, the results indicate that the sulfate radicals formed react with water in alkaline conditions, which are the optimal for the reaction, producing hydroxyl radicals which appear to be the dominant species leading to the rapid degradation of propylparaben. To the best of our knowledge, this is the first time pristine graphene has been implemented as an activator of sodium persulfate for the effective oxidation of micro-pollutants.

Fabrication of novel g-C3N4 nanocrystals decorated Ag3PO4 hybrids: Enhanced charge separation and excellent visible-light driven photocatalytic activity

Graphitic carbon nitride (g-C₃N₄) nanocrystals (NCs) decorated Ag₃PO₄ hybrids were synthesized by a facile method. The obtained samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscope (TEM), and UV-vis diffuse reflectance spectra (DRS). The SEM and TEM images showed that the as-prepared Ag₃PO₄ were composed of particles with diameters of 200-500nm, while the obtained nanocrystalline g-C₃N₄ were composed of smaller particles with average diameter of 10nm. For nanocrystalline g-C₃N₄/Ag₃PO₄ hybrids, the particle surfaces of Ag₃PO₄ were decorated with numerous g-C₃N₄ NCs, result in a larger contact area between g-C₃N₄ and Ag₃PO₄. The photocatalytic performances were evaluated by decomposing MO, phenol, bisphenol A, and RhB under visible light. Compared with Ag₃PO₄ and g-C₃N₄, the g-C₃N₄/Ag₃PO₄ hybrid (mass ratio=1:4) exhibited the best activity, which was much higher than that of bulk-g-C₃N₄/Ag₃PO₄ composite under the same conditions. The enhanced activities should be mainly ascribed to the enhanced separation efficiency of photo-generated carriers, which was proved by the photoluminescence (PL) spectra measurement. Controlled experiments proved that O₂^- and h⁺ played the chief role in the degradation process. A possible Z-scheme degradation mechanism of organic contaminant over g-C₃N₄/Ag₃PO₄ hybrid was proposed.

Effect of the acid treatment conditions of kaolinite on etheramine adsorption: A comparative analysis using chemometric tools

The present work evaluated the effect of the acid treatment conditions of natural kaolinite (NK) regarding its efficiency in removing etheramine. The treatment was conducted using sulfuric acid at the concentrations of 1 mol L^-1 (KA-01), 2 mol L^-1 (KA-02) and 5 mol L^-1 (KA-05) at 85 °C. The obtained adsorbents were characterized by X-ray fluorescence, X-ray diffraction, N₂ adsorption/desorption isotherms, zeta potential analysis and infrared spectroscopy. The Response Surface Method was used to optimize adsorption parameters (initial concentration of etheramine, adsorbent mass and pH of the solution). The results, described by means of a central composite design, were adjusted to the quadratic model. Results revealed that the adsorption was more efficient at the etheramine concentration of 400 mg L^-1, pH 10 and adsorbent mass of 0.1 g for NK and 0.2 g for KA-01, KA-02 and KA-05. The sample KA-02 presented a significant increase of etheramine removal compared to the NK sample. The adsorption kinetics conducted under optimized conditions showed that the system reached the equilibrium in approximately 30 min. The kinetic data were better adjusted to the pseudo-second order model. The isotherm data revealed that the Sips model was the most adequate one. The calculation of E_ads allowed to infer that the mechanism for etheramine removal in all the evaluated samples was chemisorption. The reuse tests showed that, after four uses, the efficiency of adsorbents in removing etheramine did not suffer significant modifications, which makes the use of kaolinite to treat effluents from the reverse flotation of iron ore feasible.