A novel L-Histidine (C, N) codoped-TiO2-CdS nanocomposite for efficient visible photo-degradation of recalcitrant compounds from wastewater

Photocatalytic degradation of metronidazole and oxytetracycline by novel l-Arginine (C, N codoped)-TiO2/g-C3N4: RSM optimization, photodegradation mechanism, biodegradability evaluation

Removal of Metronidazole (MNZ) and Oxytetracycline (OTC) from wastewater by the prepared (C, N codoped)-TiO₂/g-C₃N₄ (Graphitic carbon nitride) was examined. l-Arginine (C, N codoped)-TiO₂ and l-Arginine (C, N codoped)-TiO₂/g-C₃N₄ photocatalysts were successfully synthesized through the sol-gel method, and optimal ratio of l-arginine:TiO₂, as well as l-arginine/TiO₂:g-C₃N₄, was determined by a kinetic study of photodegradation process. The maximum photocatalytic removal rate (0.065 min^-1 for MNZ removal) was observed using 1% l-Arginine-TiO₂/g-C₃N₄ (1:1) under visible light illumination, 2.2 and 6.5 times greater than those of 1% l-Arginine-TiO₂ and pure TiO₂, respectively. l-Arginine (1%)-TiO₂/g-C₃N₄ (1:1) (co-doped-TCN) was investigated using X-ray diffraction analysis (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy Dispersive X-ray (EDX), Photo-luminescence (PL), and Differential Reflectance Spectroscopy (DRS) as the best-performing photocatalyst. Response surface methodology (RSM) was used to study the effect of co-doped-TCN dosage (0.5-1.0 g/L), pH of simulated wastewater (4-10), initial concentration of MNZ and OTC (50-100 mg/L), and irradiation time (30-90 min for MNZ and 20-40 min for OTC) on removal efficiency of the antibiotics. Also, their optimum values were determined by RSM. The treated pharmaceutical wastewater showed high biodegradability features with 5-day biological oxygen demand/chemical oxygen demand (BOD₅/COD) of 0.51 and 0.46 after 40 and 100 min reaction for OTC and MNZ, respectively. The order of reactive species responsible for the photodegradation of pollutants was •O₂^─> •OH > h⁺>¹O₂. The effect of inorganic anions showed that all anions decreased the removal efficiency of both antibiotics in order of NO₃^─> Cl^─ >SO₄^2─>HPO₄^2─ >HCO₃^─ for MNZ and NO₃^─> SO₄^2─ > Cl^─ >HPO₄^2─ >HCO₃^─ for OTC. Also, introducing different oxidants improved the photocatalytic removal efficiency with the order of H₂O₂>K₂S₂O₈> KBrO₃.

Engineered inverse opal structured semiconductors for solar light-driven environmental catalysis

Inverse opal (IO) macroporous semiconductor materials with unique physicochemical advantages have been widely used in solar-related environmental areas. In this minireview, we first summarize the synthetic methods of IO materials, emphasizing the two-step and three-step approaches, with the typical physicochemical properties being compared where applicable. We subsequently discuss the application of IO semiconductors (e.g., TiO₂, ZnO, g-C₃N₄) in various photo-related environmental techniques, including photo- and photoelectro-catalytic organic pollutant degradation in water, optical sensors for environmental monitoring, and water disinfection. The engineering strategies of these hierarchical structures for optimizing the activities for different catalytic reactions are discussed, ranging from heterojunction construction, cocatalyst loading, and heteroatom doping, to surface defect construction. Structure-activity relationships are established correspondingly. With a systematic understanding of the unique properties and catalytic activities, this review is expected to orient the design and structure optimization of IO semiconductor materials for photo-related performance improvement in various environmental techniques. Finally, the challenges of emerging IO structured semiconductors and future development directions are proposed.

Preparation and modification methods of defective titanium dioxide-based nanoparticles for photocatalytic wastewater treatment-a comprehensive review

The rapid population growth and industrial expansion worldwide have created serious water contamination concerns. To curb the pollution issue, it has become imperative to use a versatile material for the treatment. Titanium dioxide (TiO₂) has been recognized as the most-studied nanoparticle in various fields of science and engineering due to its availability, low cost, efficiency, and other fascinating properties with a wide range of applications in modern technology. Recent studies revealed the photocatalytic activity of the material for the treatment of industrial effluents to promote environmental sustainability. With the wide band gap energy of 3.2 eV, TiO₂ can be activated under UV light; thus, many strategies have been proposed to extend its photoabsorption to the visible light region. In what follows, this has generated increasing attention to study its characteristics and structural modifications in different forms for photocatalytic applications. The present review provides an insight into the understanding of the synthesis methods of TiO₂, the current progress in the treatment techniques for the degradation of wide environmental pollutants employing modified TiO₂ nanoparticles, and the factors affecting its photocatalytic activities. Further, recent developments in using titania for practical applications, the approach for designing novel nanomaterials, and the prospects and opportunities in this exciting area have been discussed.

Enhanced photocatalytic activity and charge carrier separation of CNT/TiO2/WO3/CdS catalyst for the visible-light photodegradation of reactive blue 19

The novel quaternary CNT/TiO₂/WO₃/CdS nanostructure was fabricated to be employed in the photocatalytic degradation of reactive blue 19 (RB19) under the visible light irradiation. The physicochemical properties of the pure TiO₂, CNT/TiO₂, CNT/TiO₂/WO₃, and CNT/TiO₂/WO₃/CdS were characterized using XRD, FTIR, FESEM, EDX, DRS, PL, and BET analyses. The photodegradation results showed that the optimum weight percentage of CNT, WO₃, and CdS was 4%, 35%, and 5%, respectively. The highest RB19 degradation efficiency of CNT/TiO₂/WO₃/CdS was achieved 97%. Besides, the central composite design was applied to model and optimize the photocatalytic activity of CNT/TiO₂/WO₃/CdS nanocatalyst and assess the effects of processing variables including RB19 concentration, catalyst concentration, pH, and irradiation time on the response. RB19 concentration and pH had the most and the second most significant role in the removal efficiency. While increasing the catalyst concentration and irradiation time positively enhanced the removal efficiency to more than 82%, increasing the pH and dye concentration showed the remarkable hindering effects on the removal efficiency by about 45% reduction. The reusability of the synthesized catalysts was studied under the optimum conditions as follows: [RB19] = 25 mg/L, [catalyst] = 1 g/L, pH of 4, and irradiation time = 2 h. The COD and TOC analyses were also conducted during photodegradation process. The COD and TOC removal efficiencies were achieved about 67% and 62%, respectively.

Toward efficient removal of organic pollutants in water: A tremella-like iron containing metal-organic framework in Fenton oxidation

The treatment of wastewater containing organic pollutants has become a serious issue, and one of the advanced oxidation process, Fenton oxidation is recognized as an ideal way owing to its universality and environmental friendliness, thus efficient and economic catalysts are in great demand. Herein by incorporating Fe²⁺ containing compound as ligand, a tremella-like iron containing metal-organic framework (TFMOF) was synthesized with zirconium acetate and 1,1'-ferrocene-dicarboxylic acid though a facile solvothermal method. The TFMOF combined the merits of both ferrocene moiety with well dispersed Fe²⁺ sites in the molecular level and MOF films with large surface areas and exposed sites. And the morphology and crystal structure of TFMOF were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. Moreover, employed as an effective catalyst in Fenton oxidation, over 99%, 95% and 97% of rhodamine B, methyl orange and reactive black V were rapidly degraded without the assistance of additional irradiation, and degradation conditions like pH, H₂O₂ and initial pollutant concentrations as well as the reaction kinetic was investigated, indicating the hydroxyl radical generated in the presence of TFMOF and H₂O₂ was able to degrade the pollutants into non-toxic molecular. Besides, the catalytic activity of TFMOF maintained well after three cycles. The good activity and universality of TFMOF make it a promising catalyst for the treatment of wastewater.

Enhanced oil removal from a real polymer production plant by cellulose nanocrystals-serine incorporated polyethersulfone ultrafiltration membrane

As discharging oily wastewater from industries to the environment is a potential threat for the aquatic ecosystem, in this research, oil removal from a real case of Kermanshah polymer production plant wastewater was investigated. The focus of this study was on improving the oil rejection performance of polyethersulfone (PES) ultrafiltration membrane due to adding cellulose nanocrystals (CNC) and modified CNC with serine amino acid (CNC-Ser) in PES mix matrix. From the results, the membranes embedded with CNC-Ser showed better performance in terms of water flux, flux recovery ratio, and oil rejection (higher than 97%) compared to the modified membranes with CNC. The lowest water contact angle (41.37°), smoother surface, and higher negative surface potential (- 24 mV) were achieved for the optimum loading of CNC-Ser. Besides, long-term performance of the membranes with optimum loading of CNC and CNC-Ser were compared in both dead-end and cross-flow setups.

A reusable visible driven N and C-N doped TiO2 magnetic nanocomposites for photodegradation of direct red 16 azo dye in water and wastewater

The visible active N-doped TiO₂/ZnFe₂O₄ (urea-TiO₂/ZnFe₂O₄) and CN-codoped TiO₂/ZnFe₂O₄ (L-asparagine-TiO₂/ZnFe₂O₄) nanocomposites were successfully synthesized by the sol-gel-hydrothermal method for direct red 16 (DR16) photodegradation. Their properties of the prepared nanocomposites were analysed using XRD, FT-IR, FE-SEM, EDX, DRS and PL tests. The DRS and PL results confirmed a narrow band-gap energy and low recombination rate of photo-produced electron and hole pairs, respectively. The effect of adding various dopant agents (urea and L-asparagine) with different loadings and magnetic nanoparticle (ZnFe₂O₄) into TiO₂ sol on the photodegradation of DR16 was also evaluated. As a result, the L-asparagine (2 wt. %)-TiO₂/ZnFe₂O₄ is the best photocatalyst compared to the other modified TiO₂ nanocomposites due to its narrow band gap and high quantum efficiency. The catalyst concentration (1-2 g/L), DR16 concentration (25-45 ppm), initial pH (4-10), and irradiation time (30-90 min) as numerical variables were also considered for photocatalytic process analysis and moulding by central composite design (CCD). The increase in the pH and dye concentration reduces the photodegradation efficiency while irradiation time and catalyst concentration effectively improved its photodegradation efficiency. The DR16 was completely removed at 25 ppm of DR16, initial pH of 4 and 1.5 g/L of photocatalyst after 90-min irradiation. The photoactivity test was also repeated four times by reused L-asparagine-TiO₂/ZnFe₂O₄ photocatalyst at optimum conditions. The decrease of dye degradation and loss of photocatalyst were not significant which was approved by the good performance and high recovery capability of the prepared nanocomposite.

Color removal from wastewater using a synthetic high-performance antifouling GO-CPTMS@Pd-TKHPP/polyether sulfone nanofiltration membrane

Modified graphene oxide with 5,10,15,20-tetrakis-(4-hexyloxyphenyl)-porphyrin and palladium (II) (signified by GO-CPTMS@Pd-TKHPP) prepared as a novel antifouling polyether sulfone (PES) blended nanofiller membrane. The membrane efficiency has been analyzed such as pure water flux (PWF), hydrophilicity, and antifouling features. By increasing of modified graphene oxide percentage from 0 to 0.1 wt.% in the polymer matrix, the PWF was incremented from 14.35 to 37.33 kg/m2·h at 4 bar. The membrane flux recovery ratio (FRR) has been investigated by applying powdered milk solution; the FRR results indicated that the 0.1 wt.%-modified graphene oxide membrane showed a positive effect on fouling behavior with Rir and FRR value 8.24% and 91.76%, respectively. The nanofiltration membrane performance was assessed applying the Direct Red 16 dye rejection. It was demonstrated that the optimal membranes (0.1 wt.%-modified graphene oxide) had notable dye removal (99.58% rejection). The results are also verified by measuring the scanning electron microscopy (SEM), water contact angle (WCA), and atomic microscopy analysis (AFM).

In situ composite of Co-MOF on a Ti-based material for visible light multiphase catalysis: synthesis and the photocatalytic degradation mechanism

A Co-MOF/Ti-based Z-type heterojunction prepared by an in situ growth method exhibits good photocatalytic activity for tetracycline.

Holistic process evaluation of non-conventional palm oil mill effluent (POME) treatment technologies: A conceptual and comparative review

Thriving oil palm agroindustry comes at a price of voluminous waste generation, with palm oil mill effluent (POME) as the most cumbersome waste due to its liquid state, high strength, and great discharge volume. In view of incompetent conventional ponding treatment, a voluminous number of publications on non-conventional POME treatments is filed in the Scopus database, mainly working on alternative or polishing POME treatments. In dearth of such comprehensive review, all the non-conventional POME treatments are rigorously reviewed in a conceptual and comparative manner. Herein, non-conventional POME treatments are sorted into the five major routes, viz. biological (bioconversions - aerobic/anaerobic biodegradation), physical (flotation & membrane filtration), chemical (Fenton oxidation), physicochemical (photooxidation, steam reforming, coagulation-flocculation, adsorption, & ultrasonication), and bioelectrochemical (microbial fuel cell) pathways. For aforementioned treatments, the constraints, pros, and cons are qualitatively and quantitatively (with compiled performance data) detailed to indicate their process maturity. Authors recommended (i) bioconversions, adsorption, and steam reforming as primary treatments, (ii) flotation and ultrasonication as pretreatments, (iii) Fenton oxidation, photooxidation, and membrane filtration as polishing treatments, and (iv) microbial fuel cell and coagulation-flocculation as pretreatment or polishing treatment. Life cycle assessments are required to evaluate the environmental, economic, and energy aspects of each process.

Hole Doping to Enhance the Photocatalytic Activity of Bi4NbO8Cl

An increase of carrier concentration is one of the most important routes for enhancing the catalytic performance of semiconductor photocatalysts. In this study, the Sillén–Aurivillius oxychloride Bi4NbO8Cl with hole doping was successfully prepared by a solid-state reaction method. X-ray powder diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible diffuse reflectance spectra (UV–vis DRS), X-ray photoelectron spectrometry (XPS) and photoluminescence spectra (PL) were used to characterize and analyze the prepared samples. The experimental results and density functional theory calculations demonstrate that hole doping can be formed in Bi4NbO8Cl by inserting zinc into the niobium site, and the photocatalytic activity can be improved by introducing additional holes into Bi4NbO8Cl. The photogenerated hole (h+) is considered to be the main active species to degrade trypan blue (TB) through trapping experiments. The optimal photocatalyst of Bi4Nb0.8Zn0.2O8Cl exhibits excellent photocatalytic activity in degradation of trypan blue under visible light irritation. Moreover, a possible photocatalytic degradation mechanism is discussed according the experimental and analytical results.

Complementary behavior of doping and loading in Ag/C-ZnTa2O6 for efficient visible-light photocatalytic redox towards broad wastewater remediation

This work reports on the simple fabrication of a silver loaded and carbon doped zinc tantalate (Ag/C-ZnTa₂O₆) photocatalyst with visible light photocatalytic activity toward broad wastewater remediation, including high photo-reduction of Cr(vi) (98.4% in 210 min), excellent photo-oxidation of tetracycline hydrochloride (94.7% in 210 min), and superior photo-degradation of multiple dyes (>99.0% within 210 min). The optimal photocatalytic performance of Ag/C-ZnTa₂O₆ is mainly due to the excellent visible light absorption capacity and superior electron-hole separation efficiency, which is ascribed to the complementary behavior between carbon doping and silver loading. Particularly, the generation of defects due to C-doping is greatly inhibited by Ag-loading, and the SPR effect of Ag nanoparticles is enhanced due to the obstruction of Ag⁺ by C doping.

Integrating adsorption and photocatalysis: A cost effective strategy for textile wastewater treatment using hybrid biochar-TiO2 composite

TiO₂ based photocatalysts are extensively used for textile wastewater treatment as they are ecofriendly, inexpensive, easily available, nontoxic and have higher photostabililty. However, their wider band gap, charge carrier's recombination, and utilization of light absorbance limits their performance. In the present work, a hybrid biochar-TiO₂ composite (BCT) has been synthesized by a facile synthesis strategy to overcome these problems. These photocatalysts are characterized using X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), Fourier Transform Infrared (FTIR), UV-vis diffuse reflectance spectra (DRS), and photoluminescence (PL) to evaluate their crystallinity, morphology, functional groups, bandgap energy and charge separation properties, respectively. The photodegradation of simulated textile wastewater is analyzed using hybrid composites. The hybrid biochar-TiO₂ composite showed higher charge separation, slow recombination of electron-hole pairs, and enhanced light absorption as compared to control (pure TiO₂ and BC alone). 99.20 % photodegradation efficiency of dye-simulated wastewater is achieved employing optimum hybrid composite, while the pure biochar and TiO₂ samples exhibits 85.20 % and 42.60 % efficiencies, respectively. The maximum adsorption capacity is obtained for hybrid biochar-TiO₂ sample, 74.30 mgg^-1 in comparison to biochar (30.40 mgg^-1) and pure TiO₂ (1.50 mgg^-1). The results show that hybrid biochar-TiO₂ composites can perform in the target application of organic industrial pollutant removal.

Construction of BPQDs/Ti3C2@TiO2 Composites with Favorable Charge Transfer Channels for Enhanced Photocatalytic Activity under Visible Light Irradiation

Design and construction of double heterojunction is favorable to improve the separation and migration efficiency of photogenerated carriers, thus preferably solve the problems of environmental pollution and energy crisis. Herein, TiO2 nanoparticles (NPs) are in-situ grown on highly conductive Ti3C2 nanosheets via low-temperature hydrothermal strategy, and then black phosphorus quantum dots (BPQDs) are introduced on the surface of TiO2 NPs. Under hydrothermal temperature 120 °C, the BPQDs/Ti3C2@TiO2 photocatalyst exhibits remarkable enhanced photocatalytic degradation of methyl orange (MO) and hydrogen evolution reaction (HER) compared with BPQDs/Ti3C2 and Ti3C2@TiO2 composites. Enhanced photocatalytic activity can be attributed to (i) the BPQDs with tunable bandgaps are deposited on the TiO2 NPs to form intimate heterojunction, which facilitates the electrons transfer from the conduction band (CB) of BPQDs to the CB of TiO2; (ii) the electrons quickly migrate from CB of TiO2 NPs to the Ti3C2 nanosheets with excellent electronic conductivity via electron transfer channel, which is beneficial to prolong the lifetime of electrons and hinder the recombination of photogenerated carriers; (iii) the enhanced visible light absorption and enlarged specific surface area of BPQDs/Ti3C2@TiO2 further accelerate the photocatalytic reaction. This work emphasizes the essential role of quantum dots in the construction of double heterojunction and the potential application of Ti3C2 MXene for improving photocatalytic activity.