Pullout strength of cancellous screws in human femoral heads depends on applied insertion torque, trabecular bone microarchitecture and areal bone mineral density

Value of different preoperative bone evaluation methods in predicting intraoperative screw insertion torque: a prospective clinical comparative trial

BACKGROUND CONTEXT

Establishing good screw-bone structural stability is conducive to reducing the risk of postoperative screw loosening. Screw insertion torque is an objective index for evaluating screw-bone structural stability. Therefore, accurate prediction of screw insertion torque can improve the preoperative evaluation of patients, optimize the surgical plan, and improve the surgical effect. At present, the correlation between different bone assessment methods and screw insertion torque is unclear.

PURPOSE

The aim of this study was to evaluate the correlation between different bone assessment methods and screw insertion torque and to optimize the predictive performance of screw insertion torque through mathematical modeling combined with different radiology methods.

DESIGN

Prospective cross-sectional study.

PATIENT SAMPLES

Seventy-seven patients with preoperatively available DXA, CT and MRI data who underwent spinal fixation surgeries between October 2022 and September 2023 and 357 sets of screw data were included in this analysis.

OUTCOME MEASURES

Spinal, vertebrae-specific and screw trajectory's BMD were measured preoperatively by different imaging modalities. Intraoperative screw insertion torque was measured using an electronic torque wrench.

METHODS

Pearson linear correlation, scatter plots and univariate linear regression were used to evaluate the correlation between different bone evaluation methods and screw insertion torque. Different bone evaluation methods were fitted into the prediction model of screw torque and the related equations were obtained.

RESULTS

Screw insertion torque had the strongest positive correlation with the volumetric bone mineral density (vBMD) of the screw trajectory (Pedicle screw insertion torque (PSIT): R = 0.618, p<.001; Terminal screw insertion torque (TSIT): R = 0.735, p<.001). A weak negative correlation was found between the screw insertion torque and level specific vertebral bone quality (VBQ) (PSIT: R = -0.178, p=.001; TSIT: R = -0.147, p=.006). We also found that the PSIT was strongly correlated with the TSIT (R = 0.812, p<.001).

CONCLUSIONS

Compared to other bone quality assessment methods, screw trajectory vBMD may be better predict the magnitude of screw insertion torque. In addition, we further optimized preoperative assessments by constructing a mathematical model to better predict screw insertion torque. In conclusion, clinicians should select appropriate preoperative bone quality assessment methods, identify potential low-torque patients, optimize surgical plans, and ultimately improve screw insertion accuracy and reduce postoperative screw loosening rate.

Preoperative Computed Tomography in Guiding the Length of Cannulated Screws in Medial Malleolar Fractures

Excessive lengths of partially threaded cannulated screws in medial malleolus fractures are often related to failure of fixation. This study aimed to analyze the distribution and density of cancellous bone in the medial malleolus among healthy individuals and provide a theoretical basis for determining the lengths of cannulated screws based on preoperative computed tomography (CT) to achieve stable fixation of medial malleolus fractures. Between January 2012 and December 2016, 100 patients (without ankle fractures) who underwent computed tomography of the distal tibia were included. Specific levels on the computed tomography images were selected to assess the density and length of valid cancellous bone in the medial malleolus. Meanwhile, we followed up 44 patients who underwent open reduction and internal fixation of medial malleolus fractures based on preoperative computed tomography-based measurements. The valid lengths of cancellous bone in the medial malleolus were significantly different between men and women (p < .05). In addition, there was a significant difference among different age groups (p < .05). All patients were followed up to union without displacement. Age and gender have a considerable impact on the distribution and density of cancellous bone in the medial malleolus. The density and length of valid cancellous bone decrease with age. The shoulder of the tibial plafond in medial malleolus, which is a weak part of cancellous bone, is a common site of fracture. Short screws are recommended for fixation in elderly patients. In conclusion, preoperative computed tomography can help determine the length and location of cannulated screws.

Micro-CT analysis of the Lisfranc complex reveals higher bone mineral density in dorsal compared to plantar regions

Injuries to the Lisfranc complex may require surgical fixation, the stability of which may be correlated with bone mineral density (BMD). However, there is limited research on regional BMD variations in the Lisfranc complex. This study used quantitative micro-CT to characterize regional BMD in the four bones (medial cuneiform, intermediate cuneiform, first metatarsal, and second metatarsal) of this complex. Twenty-four cadaveric specimens were imaged with a calibration phantom using micro-CT. Each bone was segmented and divided into eight regions based on an anatomical coordinate system. BMD for each octant was calculated using scan-specific calibration equations and average image intensity. Differences between regions were analyzed using ANOVA with post hoc analysis and differences between groups of four octants in each plane were analyzed with t-tests with significance level α = 0.05. The highest density region in the medial cuneiform was the distal-dorsal-lateral and dorsal regions showed significantly higher BMD than plantar regions. The intermediate cuneiform had the highest density in the distal-dorsal-medial region and the dorsal and medial regions had higher BMD than the plantar and lateral regions, respectively. The densest region of the first metatarsal was the distal-dorsal-lateral and distal regions had significantly higher BMD than proximal regions. In the second metatarsal, the distal-dorsal-medial region had the highest density, and the distal, dorsal, and medial regions had significantly higher BMD than the proximal, plantar, and lateral regions, respectively. The predominant finding was a pattern of increased density in the dorsal bone regions, which may be relevant in the surgical management of Lisfranc injuries.

Assessment of the Bone Mineral Density and Microstructure of the Human Femoral Head according to Different Tip-apex Distances Can Guide the Treatment of Intertrochanteric Hip Fractures

Purpose

We analyzed the microstructure and bone mineral density (BMD) of the trabecular bone in the femoral head of patients with osteoporosis.

Materials and Methods

Sixteen femoral heads with osteoporotic femoral neck fractures underwent micro-computed tomography scanning. In each tip-apex distance (TAD) of 15, 20, and 25 mm, five regions of interest (ROIs) were extracted from the central, anterior, posterior, superior, and inferior sections. A total of 15 ROIs were extracted from TADs of 15, 20, and 25 mm. The measurement parameters included BMD, percent bone volume: bone volume/total volume (BV/TV), trabecular thickness (Tb.Th), trabecular number (Tb.N), structural model index (SMI), and degree of anisotropy (DOA).

Results

The lowest BMD and BV/TV values were observed in the inferior region and differed significantly from those in other regions (P<0.05). Lower Tb.Th and Tb.N values were observed in the inferior region compared with those in the central region (P<0.05). The highest SMI value was observed in the inferior region (P<0.05). With TAD of 15 and 20 mm, the DOA values in the inferior region were lower than those in the anterior region (P<0.05). Lower BMD and BV/TV values were observed in the anterior, central, and inferior regions of TAD of 15 mm compared with those in the corresponding regions of TAD of 25 mm (P<0.05).

Conclusion

Positioning the lag screw between TAD of 20 to 25 mm and in the inferior region is recommended, and TAD of less than 15 mm is not recommended.

The effect of cement augmentation on pedicle screw fixation under various load cases : results from a combined experimental, micro-CT, and micro-finite element analysis

Aims

Anchorage of pedicle screw rod instrumentation in the elderly spine with poor bone quality remains challenging. Our study aims to evaluate how the screw bone anchorage is affected by screw design, bone quality, loading conditions, and cementing techniques.

Methods

Micro-finite element (µFE) models were created from micro-CT (μCT) scans of vertebrae implanted with two types of pedicle screws (L: Ennovate and R: S⁴). Simulations were conducted for a 10 mm radius region of interest (ROI) around each screw and for a full vertebra (FV) where different cementing scenarios were simulated around the screw tips. Stiffness was calculated in pull-out and anterior bending loads.

Results

Experimental pull-out strengths were excellently correlated to the µFE pull-out stiffness of the ROI (R² > 0.87) and FV (R² > 0.84) models. No significant difference due to screw design was observed. Cement augmentation increased pull-out stiffness by up to 94% and 48% for L and R screws, respectively, but only increased bending stiffness by up to 6.9% and 1.5%, respectively. Cementing involving only one screw tip resulted in lower stiffness increases in all tested screw designs and loading cases. The stiffening effect of cement augmentation on pull-out and bending stiffness was strongly and negatively correlated to local bone density around the screw (correlation coefficient (R) = -0.95).

Conclusion

This combined experimental, µCT and µFE study showed that regional analyses may be sufficient to predict fixation strength in pull-out and that full analyses could show that cement augmentation around pedicle screws increased fixation stiffness in both pull-out and bending, especially for low-density bone.

Cite this article: Bone Joint Res 2021;10(12):797–806.

Changes in scapular bone density vary by region and are associated with age and sex

BACKGROUND

Decreases in bone density of the scapula due to age and disease can make orthopedic procedures such as arthroplasty and fracture fixation challenging. There is limited information in the literature regarding the effect of age and sex on the patterns of these density changes across the bone. Characterizing these changes could assist the surgeon in planning optimal instrumentation placement.

METHODS

Ninety-seven 3-dimensional models of the scapula were segmented from routine clinical computed tomography scans, and an opportunistic quantitative computed tomography approach was used to obtain detailed calibrated bone density measurements for each bone model. The effects of age and sex on cortical and trabecular bone density were assessed for the entire scapula. Specific regions (eg, scapular spine) where these factors had a significant effect were identified. Three-dimensional models were generated to allow clear visualization of the changes in density patterns.

RESULTS

Cortical bone loss averaged 1.0 mg/cm³ and 0.3 mg/cm³ per year for female and male subjects, respectively, and trabecular bone loss averaged 1.6 mg/cm³ and 1.2 mg/cm³, respectively. However, several regions had loss rates several times greater. Areas that were significantly affected by age included the acromion, scapular spine, base of the coracoid, inferior glenoid neck, and glenoid vault. Areas that were significantly affected by sex were the scapular spine and body.

CONCLUSIONS

These findings provide evidence that the bone density distribution across the scapula changes non-uniformly because of factors including sex and age. Despite overall trends of bone loss, there remains significant variability between individuals, and subject-specific tools for planning surgical procedures in which scapular fixation is required may be beneficial.

Trabecular bone density distribution in the scapula of patients undergoing reverse shoulder arthroplasty

Background

To improve implant survival after reverse shoulder arthroplasty (RSA), surgeons need to maximize screw fixation. However, bone density variation and distribution within the scapula are not well understood as they relate to RSA. The three columns of bone in the scapula surrounding the glenoid fossa are the lateral border, the base of the coracoid process, and the spine of the scapula. In our previous study by Daalder et al on cadaveric specimens, the coracoid column was significantly less dense than the lateral border and spine. This study’s objective was to verify whether these results are consistent with computer tomography (CT) scan information from patients undergoing RSA.

Methods

Two-dimensional axial CT images from twelve patients were segmented, and a three-dimensional digital model of the scapula was subsequently created using Mimics 17.0 Materialise Software (Leuven, Belgium). Hounsfield unit (HU) values representing cortical bone were filtered out to determine the distributions of trabecular bone density. An analysis of variance with post hoc Bonferroni tests determined the differences in bone density between the columns of bone in the scapula.

Results

The coracoid superolateral (270 ± 45.6 HU) to the suprascapular notch was significantly less dense than the inferior (356 ± 63.6 HU, P = .03, d_s = 1.54) and anterosuperior portion of the lateral border (353 ± 68.9 HU, P = .04, d_s = 1.42) and the posterior (368 ± 70 HU, P = .007, d_s = 1.65) and anterior spine (370 ± 78.9 HU, P = .006, d_s = 1.54).

Discussion/Conclusion

The higher-density bone in the spine and lateral border compared with the coracoid region may provide better bone purchase for screws when fixing the glenoid baseplate in RSA. This is in agreement with our previous study and indicates that the previous cadaveric results are applicable to clinical CT scan data. When these studies are taken together, they provide robust evidence for clinical applications, including having surgeons aim screws for higher-density regions to increase screw fixation, which may decrease micromotion and improve implant longevity.

Augmenting a dynamic hip screw with a calcium sulfate/hydroxyapatite biomaterial

Internal fixation failure in hip fractures can lead to reoperation. Calcium sulfate/hydroxyapatite (CaS/HA) is a biomaterial that can be used for augmenting fracture fixation. We aimed to determine whether an injection of 2 ml CaS/HA increases the fixation of a dynamic hip screw inserted in synthetic and human trabecular bone. The study consists of two parts: 1) synthetic bone blocks (n = 74), with three subgroups: empty (cannulated screw, no injection), cannulated, and fenestrated; and 2) osteoporotic human femoral heads (n = 29), with the same subgroups. The heads were imaged using µCT. Bone volume fraction, insertion angle, and head diameter were measured. Pullout tests were performed and peak force, stiffness, and work were measured. The fenestrated group showed increases in pullout strength compared to no injection in the synthetic blocks. The cannulated group showed a higher pullout strength in low-density blocks. In the femoral heads, the variation was larger and there were no significant differences between groups. The bone volume fraction correlated with the peak force and work, and the insertion angle correlated with the stiffness. CaS/HA can improve the fixation of a dynamic hip screw. For clinical use, spreading of the material around the threads of the screw must be ensured.

Osseointegration of a novel dental implant in canine

This study aimed to compare and verify the osseointegration performance of a novel implant (NI) in vivo, which could provide a useful scientific basis for the further development of NIs. Thirty-two NIs treated with hydrofluoric acid and anodization and sixteen control implants (CIs) were placed in the mandibles of 8 beagles. Micro-CT showed that the trabecular number (Tb.N) significantly increased and trabecular separation (Tb.Sp) significantly decreased in the NIs at 2 weeks. Significant differences were found in the trabecular thickness, Tb.N, Tb.Sp, bone surface/bone volume ratio, and bone volume/total volume ratio between the two groups from the 2nd–4th weeks. However, there were no significant differences between the two groups in the bone volume density at 2, 4, 8, or 12 weeks or bone-implant contact at 2 or 4 weeks, but the BIC in the CIs was higher than that in the NIs at the 8th and 12th weeks. Meanwhile, the histological staining showed a similar osseointegration process between the two groups over time. Overall, the NIs could be used as new potential implants after further improvement.

Drilling Energy Correlates With Screw Insertion Torque, Screw Compression, and Pullout Strength: A Cadaver Study

INTRODUCTION

To determine whether drilling energy correlates with bone mineral density (BMD), maximum insertion torque (MIT), maximum screw compression, and pullout strength (POS).

METHODS

Ten cadaver tibias were used for testing. Unicortical pilot holes were drilled and the drilling energy measured. Drill site bone quality was determined with microcomputed tomography. Drill holes were randomly assigned to POS or MIT testing using 3.5-mm cortical screws engaging only the near cortex. Pearson correlation coefficients were calculated to determine the relationship between drilling energy, BMD, POS, MIT, and maximum screw compression.

RESULTS

Drilling energy was correlated with BMD (P < 0.001). Compared with BMD, drilling energy had a better correlation with MIT, maximum screw compression, and POS. Maximum screw compression also correlated with MIT (P = 0.012).

CONCLUSIONS

Drilling energy better correlates with MIT, maximum screw compression, and POS compared with BMD in cadaver cortical bone. Dynamically measuring drilling energy may help inform the orthopaedic surgeon as to the quality of the bone before insertion of implants.

Measurement of Scaphoid Bone Microarchitecture: A Computed Tomography Imaging Study and Implications for Screw Placement

PURPOSE

High bone density and quality is associated with improved screw fixation in fracture fixation. The objective of this study was to assess bone density and quality in the proximal and distal scaphoid to determine optimum sites for placement of 2 screws in scaphoid fracture fixation.

METHODS

Twenty-nine cadaveric human scaphoid specimens were harvested and scanned using micro-computed tomography. Bone density (bone volume fraction) and bone quality (relative bone surface area, trabecular number, and trabecular thickness) were evaluated in 4 quadrants within each of the proximal and distal scaphoid.

RESULTS

The proximal radial quadrant of the scaphoid had significantly greater bone volume than the distal ulnar (mean difference, 33.2%) and distal volar quadrants (mean difference, 32.3%). There was a significantly greater trabecular number in the proximal radial quadrant than in the distal ulnar (mean difference, 16.7%) and in the distal volar quadrants (mean difference, 15.9%) and between the proximal ulnar and the distal ulnar quadrants (mean difference, 12%). There was a significantly greater bone surface area in the proximal radial and distal radial quadrants than in the distal ulnar and distal volar quadrants. There were no significant differences in trabecular thickness between the 8 analyzed quadrants CONCLUSIONS: Although there are differences in bone volume, trabecular number, and bone surface area between the proximal pole of the scaphoid and that of the distal pole, there were no significant differences in the bone quality (trabecular thickness, trabecular number, and relative bone surface area) and density (bone volume fraction) between the 4 quadrants of the proximal or distal pole of the cadaveric scaphoids studied.

CLINICAL RELEVANCE

Insertion of 2 headless compression screws can be determined by ease of surgical access and ease of screw positioning and not by differences in bone quality or density of the proximal or distal scaphoid.

Real time monitoring of screw insertion using acoustic emission can predict screw stripping in human cancellous bone

BACKGROUND

To develop experience, orthopaedic surgeons train their own proprioception to detect torque during screw insertion. This experience is acquired over time and when implanting conventional/non-locked screws in osteopenic cancellous bone the experienced surgeon still strips between 38 and 45%. Technology needs to be investigated to reduce stripping rates. Acoustic-Emission technology has the ability to detect stress wave energy transmitted through a screw during insertion into synthetic bone. Our hypothesis is Acoustic-Emission waves can be detected through standard orthopaedic screwdrivers while advancing screws through purchase and overtightening in cancellous human bone with different bone mineral densities replicating the clinical state.

METHODS

77 non-locking 4 mm and 6.5 mm diameter cancellous bone screws were inserted through to stripping into the lateral condylar area of 6 pairs of embalmed distal femurs. Specimens had varying degrees of bone mineral density determined by quantitative CT. Acoustic-Emission energy and axial force were detected for each test.

RESULTS

The tests showed a significant high correlation between bone mineral density and Acoustic-Emission energy with R = 0.74. A linear regression model with the mean stripping load as the dependent variable and mean Acoustic-Emission energy, bone mineral densities and screw size as the independent variables resulted in r² = 0.94.

INTERPRETATION

This experiment succeeded in testing real time Acoustic-Emission monitoring of screw purchase and overtightening in human bone. Acoustic-Emission energy and axial compressive force have positive high correlation to bone mineral density. The purpose is to develop a known technology and apply it to improve the bone-metal construct strength by reducing human error of screw overtightening.

Surgical performance when inserting non-locking screws: a systematic review

Billions of screws are inserted by surgeons each year, making them the most commonly inserted implant. When using non-locking screws, insertion technique is decided by the surgeon, including how much to tighten each screw. The aims of this study were to assess, through a systematic review, the screw tightness and rate of material stripping produced by surgeons and the effect of different variables related to screw insertion.

Twelve studies were included, with 260 surgeons inserting a total of 2793 screws; an average of 11 screws each, although only 1510 screws have been inserted by 145 surgeons where tightness was measured – average tightness was 78±10% for cortical (n = 1079) and 80±6% for cancellous screw insertions (n = 431).

An average of 26% of all inserted screws irreparably damaged and stripped screw holes, reducing the construct pullout strength. Furthermore, awareness of bone stripping is very poor, meaning that screws must be considerably overtightened before a surgeon will typically detect it.

Variation between individual surgeons’ ability to optimally insert screws was seen, with some surgeons stripping more than 90% of samples and others hardly any. Contradictory findings were seen for the relationship between the tightness achieved and bone density.

The optimum tightness for screws remains unknown, thus subjectively chosen screw tightness, which varies greatly, remains without an established target to generate the best possible construct for any given situation. Work is needed to establish these targets, and to develop methods to accurately and repeatably achieve them.

Cite this article: EFORT Open Rev 2020;5:26-36. DOI: 10.1302/2058-5241.5.180066

Non-setting, injectable biomaterials containing particulate hydroxyapatite can increase primary stability of bone screws in cancellous bone

BACKGROUND

Fracture fixation in weak bone is still a clinical challenge. Screw augmentation was shown to successfully increase their primary stability. The currently used calcium phosphate or polymeric bone cements, however, present important drawbacks such as induced toxicity and/or impaired bone neo-formation. A new approach to enhance bone screw primary stability without affecting bone formation is the use of non-setting, calcium phosphate loaded soft materials as the augmentation material.

METHODS

Two types of biomaterials (non-crosslinked hyaluronic acid as viscous fluid and agar as hydrogel) were loaded with 40 wt/vol% of hydroxyapatite particles and characterized. The screw augmentation effect of all materials was evaluated through pull-out tests in bovine cancellous bone and compared to the non-augmented situation (control). The bone mineral density of each test sample was measured with μCT scans and was used to normalize the pull-out strength.

FINDINGS

Both materials loaded with hydroxyapatite increased the normalized pull-out strength of the screws compared to control samples and particle-free materials. This counter-intuitive augmentation effect increased with decreasing bone mineral density and was independent from the type of the soft materials used.

INTERPRETATION

We were able to demonstrate that non-setting, injectable biomaterials loaded with ceramic particles can significantly enhance the primary stability of bone screws. This material combination opens the unique possibility to achieve a screw augmentation effect without impairing or even potentially favoring the bone formation in proximity to the screw. This effect would be particularly advantageous for the treatment of osteoporotic bone fractures requiring a stabilization with bone screws.

Trabecular bone density distribution in the scapula relevant to reverse shoulder arthroplasty

Background

How trabecular bone density varies within the scapula and how this may lead to more optimal reverse shoulder arthroplasty (RSA) screw placement has not been addressed in the scientific literature. The 3 columns of trabecular bone within the scapula adjacent to the glenoid fossa, one extending through the lateral border, a second into the base of the coracoid process, and a third extending into the spine of the scapula, were hypothesized to be of relatively similar density.

Methods

Two-dimensional axial computed tomography (CT) images of 19 fresh frozen cadaver specimens were obtained. Digital Imaging and Communications in Medicine (DICOM; National Electrical Manufacturers Association, Rosslyn, VA, USA) image files of the CT scanned scapulae were imported into Mimics 17.0 Materialise Software (Leuven, Belgium) for segmentation and 3-dimensional digital model generation. To determine the distribution of trabecular bone density, Hounsfield unit (HU) values in the scapulae gray value files obtained from Mimics were filtered to remove any cortical bone. HU values of 650 define the corticocancellous interface in CT image data and were considered to be cortical bone. Analyses of variance with post hoc Bonferroni tests were used to determine statistical differences between the intra- and inter-regions of bone density comparisons.

Results

The base of the coracoid process was statistically significantly less dense than the spine and the lateral border of the scapulae examined (P < .05).

Discussion/Conclusion

The higher-quality bone in the spine and lateral border, compared with the coracoid regions, may provide better bone purchase for screws when fixing the glenoid baseplate in RSA.

Achievable accuracy of hip screw holding power estimation by insertion torque measurement

BACKGROUND

To ensure stability of proximal femoral fractures, the hip screw must firmly engage into the femoral head. Some studies suggested that screw holding power into trabecular bone could be evaluated, intraoperatively, through measurement of screw insertion torque. However, those studies used synthetic bone, instead of trabecular bone, as host material or they did not evaluate accuracy of predictions. We determined prediction accuracy, also assessing the impact of screw design and host material.

METHODS

We measured, under highly-repeatable experimental conditions, disregarding clinical procedure complexities, insertion torque and pullout strength of four screw designs, both in 120 synthetic and 80 trabecular bone specimens of variable density. For both host materials, we calculated the root-mean-square error and the mean-absolute-percentage error of predictions based on the best fitting model of torque-pullout data, in both single-screw and merged dataset.

FINDINGS

Predictions based on screw-specific regression models were the most accurate. Host material impacts on prediction accuracy: the replacement of synthetic with trabecular bone decreased both root-mean-square errors, from 0.54 ÷ 0.76 kN to 0.21 ÷ 0.40 kN, and mean-absolute-percentage errors, from 14 ÷ 21% to 10 ÷ 12%. However, holding power predicted on low insertion torque remained inaccurate, with errors up to 40% for torques below 1 Nm.

INTERPRETATION

In poor-quality trabecular bone, tissue inhomogeneities likely affect pullout strength and insertion torque to different extents, limiting the predictive power of the latter. This bias decreases when the screw engages good-quality bone. Under this condition, predictions become more accurate although this result must be confirmed by close in-vitro simulation of the clinical procedure.

Variable Bone Density of Scaphoid: Importance of Subchondral Screw Placement

Background  Ideal internal fixation of the scaphoid relies on adequate bone stock for screw purchase; so, knowledge of regional bone density of the scaphoid is crucial. Questions/Purpose  The purpose of this study was to evaluate regional variations in scaphoid bone density. Materials and Methods  Three-dimensional CT models of fractured scaphoids were created and sectioned into proximal/distal segments and then into quadrants (volar/dorsal/radial/ulnar). Concentric shells in the proximal and distal pole were constructed in 2-mm increments moving from exterior to interior. Bone density was measured in Hounsfield units (HU). Results  Bone density of the distal scaphoid (453.2 ± 70.8 HU) was less than the proximal scaphoid (619.8 ± 124.2 HU). There was no difference in bone density between the four quadrants in either pole. In both the poles, the first subchondral shell was the densest. In both the proximal and distal poles, bone density decreased significantly in all three deeper shells. Conclusion  The proximal scaphoid had a greater density than the distal scaphoid. Within the poles, there was no difference in bone density between the quadrants. The subchondral 2-mm shell had the greatest density. Bone density dropped off significantly between the first and second shell in both the proximal and distal scaphoids. Clinical Relevance  In scaphoid fracture ORIF, optimal screw placement engages the subchondral 2-mm shell, especially in the distal pole, which has an overall lower bone density, and the second shell has only two-third the density of the first shell.

Micro-CT and micro-FE analysis of pedicle screw fixation under different loading conditions

Anchorage of pedicle screw instrumentation in the elderly spine with poor bone quality remains challenging. In this study, micro finite element (µFE) models were used to assess the specific influence of screw design and the relative contribution of local bone density to fixation mechanics. These were created from micro computer tomography (µCT) scans of vertebras implanted with two types of pedicle screws, including a full region-or-interest of 10 mm radius around each screw, as well as submodels for the pedicle and inner trabecular bone of the vertebral body. The local bone volume fraction (BV/TV) calculated from the µCT scans around different regions of the screw (pedicle, inner trabecular region of the vertebral body) were then related to the predicted stiffness in simulated pull-out tests as well as to the experimental pull-out and torsional fixation properties mechanically measured on the corresponding specimens. Results show that predicted stiffness correlated excellently with experimental pull-out strength (R² > 0.92, p < .043), better than regional BV/TV alone (R2 = 0.79, p = .003). They also show that correlations between fixation properties and BV/TV were increased when accounting only for the pedicle zone (R² = 0.66-0.94, p ≤  .032), but with weaker correlations for torsional loads (R² < 0.10). Our analyses highlight the role of local density in the pedicle zone on the fixation stiffness and strength of pedicle screws when pull-out loads are involved, but that local apparent bone density alone may not be sufficient to explain resistance in torsion.

The relationship between dental implant stability and trabecular bone structure using cone-beam computed tomography

Purpose

The objective of this study was to investigate the relationships between primary implant stability as measured by impact response frequency and the structural parameters of trabecular bone using cone-beam computed tomography(CBCT), excluding the effect of cortical bone thickness.

Methods

We measured the impact response of a dental implant placed into swine bone specimens composed of only trabecular bone without the cortical bone layer using an inductive sensor. The peak frequency of the impact response spectrum was determined as an implant stability criterion (SPF). The 3D microstructural parameters were calculated from CT images of the bone specimens obtained using both micro-CT and CBCT.

Results

SPF had significant positive correlations with trabecular bone structural parameters (BV/TV, BV, BS, BSD, Tb.Th, Tb.N, FD, and BS/BV) (P<0.01) while SPF demonstrated significant negative correlations with other microstructural parameters (Tb.Sp, Tb.Pf, and SMI) using micro-CT and CBCT (P<0.01).

Conclusions

There was an increase in implant stability prediction by combining BV/TV and SMI in the stepwise forward regression analysis. Bone with high volume density and low surface density shows high implant stability. Well-connected thick bone with small marrow spaces also shows high implant stability. The combination of bone density and architectural parameters measured using CBCT can predict the implant stability more accurately than the density alone in clinical diagnoses.

Numerical Methodology to Evaluate the Effects of Bone Density and Cement Augmentation on Fixation Stiffness of Bone-Anchoring Devices

Bone quality is one of the reported factors influencing the success of bone anchors in arthroscopic repairs of torn rotator cuffs at the shoulder. This work was aimed at developing refined numerical methods to investigate how bone quality can influence the fixation stiffness of bone anchors. To do that bone biopsies were scanned at 26-μm resolution with a high-resolution microcomputer tomography (micro-CT) scanner and their images were processed for virtual implantation of a typical design of bone anchor. These were converted to microfinite element (μFE) and homogenized classical FE models, and analyses were performed to simulate pulling on the bone anchor with and without cement augmentation. Quantification of structural stiffness for each implanted specimen was then computed, as well as stress distributions within the bone structures, and related to the bone volume fraction of the specimens. Results show that the classical method is excellently correlated to structural predictions of the more refined μFE method, despite the qualitative differences in local stresses in the bone surrounding the implant. Predictions from additional loading cases suggest that structural fixation stiffness in various directions is related to apparent bone density of the surrounding bone. Augmentation of anchoring with bone cement stiffens the fixation and alters these relations. This work showed the usability of homogenized FE (hFE) in the evaluation of bone anchor fixation and will be used to develop new methodologies for virtual investigations leading to optimized repairs of rotator cuff and glenoid Bankart lesions.