Macrovoid-free PES/SPSf/O-MWCNT ultrafiltration membranes with improved mechanical strength, antifouling and antibacterial properties

Mussel- and nacre-inspired dual-bionic alginate-based hydrogel coating with multi-matrix applicability, high separation stability and antifouling performance for oil/water separation

Natural hydrogel-modified porous matrices with superwetting interfaces are ideal for oil/water separation. In this study, inspired by two marine organisms, a novel hydrogel coating with multi-matrix suitability, high oil/water separation capability and antifouling properties was developed. Specifically, inspired by mussel byssus, hydrogel coating was successfully deposited on porous matrix surface based on the introduction of tannic acid (TA). Moreover, inspired by the "brick and mortar" microstructure of Pinctada nacre, silica particles were in-situ synthesized in the sodium alginate (SA)/Ca2+ hydrogel to provide the filling effect and to increase strength. Furthermore, Sodium alginate-tannic acid-tetraethyl orthosilicate (SA-TA-TEOS) hydrogel coating-modified membrane exhibited super-hydrophilic and underwater super-oleophobic performance (underwater oil contact angle >150°), and achieved efficient oil/water separation for four oil/water emulsions (flux = 493-584 L·m-2·h-1 and rejection = 97.3-99.5 %). The modified membrane also demonstrated good anti-fouling performance and flux recovery. Notably, hydrogel coating-modified non-woven fabric also had high oil/water separation capacity (rejection >98 %) and cyclic stability, which proved the universal applicability of this hydrogel coating. In short, this work provides new insights into the fabrication of hydrogel coating-modified porous materials based upon a marine organism biomimetic strategy, which has potential applications in separating oil/water emulsions in industrial scenarios.

Designing a novel poly (methyl vinyl ether maleic anhydride) based polymeric membrane with enhanced antifouling performance for removal of pentachlorophenol from aqueous solution

In this current study, poly (methyl vinyl ether maleic anhydride) (PMVEAMA), a sustainable additive, was incorporated into poly (ether-ether sulfone) (PEES) polymer to design a novel polymeric hybrid membrane for the efficient filtration of toxic pentachlorophenol (PCP) from an aqueous medium. Hydrophilic additives significantly altered the membrane's morphology, structure, porosity, water content, and flux performance compared to the bare PEES membrane. The influence of PMVEAMA on the structural modification of the synthesized polymer membrane was confirmed by SEM, ATR-FTIR, XRD, AFM, zeta potential and contact angle. Findings revealed that the addition of PMVEAMA to the PEES polymer enhances the porosity (17.7%-28.9%), water content (29.8%-39.8%), and pure water flux (186 Lm^-2h^-1 to 349 Lm^-2h^-1). The effect of PMVEAMA concentration on the PEES membrane exhibited more finger like pores, better porosity and hydrophilicity, reduced surface roughness, fouling and increased permeability. The fouling studies exhibit an improved 57% PCP rejection and permeation flux of 22.3 Lm^-2h^-1 due to the addition of the hydrophilic additive. Surprisingly, the incorporation of PMVEAMA into the bare PEES membrane resulted in a high flux recovery ratio of 73.7%. The antifouling properties and enhanced permeability of the PEES/PMVEAMA membrane indicates its potential application in water purification sectors for the efficient separation of contaminants.

Demulsifier-Inspired Superhydrophilic/Underwater Superoleophobic Membrane Modified with Polyoxypropylene Polyoxyethylene Block Polymer for Enhanced Oil/Water Separation Properties

Demulsifiers are considered the key materials for oil/water separation. Various works in recent years have shown that demulsifiers with polyoxypropylen epolyoxyethylene branched structures possess better demulsification effects. In this work, inspired by the chemical structure of demulsifiers, a novel superhydrophilic/underwater superoleophobic membrane modified with a polyoxypropylene polyoxyethylene block polymer was fabricated for enhanced separation of O/W emulsion. First, a typical polyoxypropylene polyoxyethylene triblock polymer (Pluronic F127) was grafted onto the poly styrene-maleic anhydride (SMA). Then, the Pluronic F127-grafted SMA (abbreviated as F127@SMA) was blended with polyvinylidene fluoride (PVDF) for the preparation of the F127@SMA/PVDF ultrafiltration membrane. The obtained F127@SMA/PVDF ultrafiltration membrane displayed superhydrophilic/underwater superoleophobic properties, with a water contact angle of 0° and an underwater oil contact angle (UOCA) higher than 150° for various oils. Moreover, it had excellent separation efficiency for SDS-stabilized emulsions, even when the oil being emulsified was crude oil. The oil removal efficiency was greater than 99.1%, and the flux was up to 272.4 L·m^-2·h^-1. Most importantly, the proposed F127@SMA/PVDF membrane also exhibited outstanding reusability and long-term stability. Its UOCA remained higher than 150° in harsh acidic, alkaline, and high-salt circumstances. Overall, the present work proposed an environmentally friendly and convenient approach for the development of practical oil/water separation membranes.

Enhancement of antifouling properties, metal ions and protein separation of poly(ether-ether-sulfone) ultrafiltration membranes by incorporation of poly ethylene glycol and n-ZnO

Composite polymeric membranes with enhanced anti-fouling properties, antimicrobial activities and flux were produced via the phase inversion technique using poly (ether-ether-sulfone) (PEES)/polyethylene glycol (PEG) and n-ZnO. SEM and ATR-FTIR spectroscopy were used to study the morphological and chemical properties of the resulting ultrafiltration membranes. PEG and n-ZnO concentration has an effect on membrane morphologies, ultrafiltration performance, thermal characteristics, metal ion separation studies, surface hydrophilicity and anti-fouling capabilities. The permeate flux increased when the PEG concentration was raised. This results revealed that adding PEG and n-ZnO to membranes increased their surface hydrophilicity and anti-fouling properties. The inclusion of 1.5 wt % n-ZnO and 5 wt % PEG to the pristine PEES membrane resulted in a higher flux of 233.76 L m^-2 h^-1, 70.09 % of water content, 47.46° of contact angle, the porosity of 30.20 %, and hydraulic resistance of 0.22 kPa/Lm^-2h^-1. Anti-fouling properties of the fabricated membrane were assessed using a model foulant BSA, which revealed a high flux recovery ratio value. As a result, the PEG and n-ZnO incorporated membrane is more hydrophilic than the virgin membrane. In addition, the prepared PEES/PEG/n-ZnO membrane showed a significant increase in metal ions and protein rejection. Furthermore, an antibacterial test of the membrane revealed that the PEG and n-ZnO composite membrane outperformed the bare PEES membrane in terms of antibacterial capabilities. Overall, the findings reveal that combining n-ZnO and PEG resulted in a membrane with improved anti-fouling capabilities and hydrophilicity, making it suitable for water purification.

Delayed Solvent-Nonsolvent Demixing Preparation and Performance of a Highly Permeable Polyethersulfone Ultrafiltration Membrane

Membrane performance optimization is a critical preparation step that ensures optimum separation and fouling resistance. Several studies have employed additives such as carbon and inorganic nanomaterials to optimize membrane performance. These particles provide excellent results but are rather costly, unstable and toxic to several biological organs. This study demonstrated that performance enhancement can also be achieved through delayed solvent−nonsolvent demixing during phase inversion membrane preparation. The rate of solvent−nonsolvent demixing was delayed by increasing the concentration of the solvent in the coagulation bath. This study employed synthetic and real water samples and several analytical techniques to compare optimized performances and properties of membranes prepared in this study with that of nanoparticle-embedded membranes in the literature. Pure water flux and BSA rejection of the membranes prepared in this study were comparable to those of nanoparticle embedded membranes. This study also shows the influence of delayed solvent−nonsolvent demixing on membrane properties such as morphology, wettability, surface roughness and porosity, thereby showing the suitability of the technique in membrane optimization. Furthermore, fouling studies showed that membranes prepared in this study have high flux recovery when fouled by humic acid feed water (>95%) and above 50% flux recovery with real water samples.

A Comparative Analysis of the Effect of Carbonaceous Nanoparticles on the Physicochemical Properties of Hybrid Polyethersulfone Ultrafiltration Membranes

Numerous studies have been previously reported on the use of nanoscale carbonaceous fillers, such as multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO), in polymeric ultrafiltration (UF) membranes; however, no insight has been clearly reported on which material provides the best enhancements in membrane performance. In this study, a comparative analysis was carried out to establish a comprehensible understanding of the physicochemical properties of hybrid polyethersulfone (PES) UF membranes incorporated with MWCNTs and GO nanoparticles at various concentrations. The hybrid membranes were prepared via the non-solvent-induced phase separation process and further characterized by field emission scanning electron microscopy and atomic force microscope (AFM). The AFM images showed homogeneous membrane surfaces with a reduction in the membrane surface roughness from 2.62 nm for bare PES to 2.39 nm for PES/MWCNTs and to 1.68 nm for PES/GO membranes due to improved hydrophilicity of the membranes. Physicochemical properties of the hybrid PES membranes were assessed, and the outcomes showed an enhancement in the porosity, pore size, water contact angle, and water permeability with respect to nanoparticle concentration. GO-incorporated PES membranes exhibited the highest porosity, pore size, and lowest contact angle as compared to PES/MWCNTs, indicating the homogeneous distribution of nanoparticles within the membrane structure. PES/MWCNTs (0.5 wt.%) and PES/GO (1.0 wt.%) hybrid membranes exhibited the highest water flux of 450.0 and 554.8 L m^-2 h^-1, respectively, at an applied operating pressure of 1 bar. The filtration and antifouling performance of the PES hybrid membranes were evaluated using 50 mg L^-1 of humic acid (HA) as a foulant at pH = 7. Compared to the bare PES membrane, the MWCNTs and GO-incorporated PES hybrid membranes exhibited enhanced permeability and HA removal. Moreover, PES/MWCNTs (0.5 wt.%) and PES/GO (1 wt.%) hybrid membranes reported HA rejection of 90.8% and 94.8%, respectively. The abundant oxygen-containing functional groups in GO-incorporated PES membranes resulted in more hydrophilic membranes, leading to enhanced permeability and fouling resistance. The antifouling properties and flux recovery ratio were improved by the addition of both nanoparticles. Given these findings, although both MWCNTs and GO nanoparticles are seen to notably improve the membrane performance, PES membranes with 1 wt.% GO loading provided the highest removal of natural organic matter, such as HA, under the same experimental conditions.

In Situ Generation of Fouling Resistant Ag/Pd Modified PES Membranes for Treatment of Pharmaceutical Wastewater

In this study, Ag and Pd bimetallic nanoparticles were generated in situ in polyethersulfone (PES) dope solutions, and membranes were fabricated through a phase inversion method. The membranes were characterized for various physical and chemical properties using techniques such as FTIR, SEM, AFM, TEM, EDS, and contact angle measurements. The membranes were then evaluated for their efficiency in rejecting EOCs and resistance to protein fouling. TEM micrographs showed uniform distribution of Ag/Pd nanoparticles within the PES matrix, while SEM images showed uniform, fingerlike structures that were not affected by the presence of embedded nanoparticles. The presence of Ag/Pd nanoparticles resulted in rougher membranes. There was an increase in membrane hydrophilicity with increasing nanoparticles loading, which resulted in improved pure water permeability (37−135 Lm2h−1bar−1). The membranes exhibited poor salt rejection (<15%), making them less susceptible to flux decline due to concentration polarization. With a mean pore radius of 2.39−4.70 nm, the membranes effectively removed carbamazepine, caffeine, sulfamethoxazole, ibuprofen, and naproxen (up to 40%), with size exclusion being the major removal mechanism. Modifying the membranes with Ag/Pd nanoparticles improved their antifouling properties, making them a promising innovation for the treatment of pharmaceutical wastewater.

Surface-engineered polyethersulfone membranes with inherent Fe-Mn bimetallic oxides for improved permeability and antifouling capability

In recent years, bimetallic oxide nanoparticles have garnered significant attention owing to their salient advantages over monometallic nanoparticles. In this study, Fe₂O₃-Mn₂O₃ nanoparticles were synthesized and used as nanomodifiers for polyethersulfone (PES) ultrafiltration membranes. A NIPS was used to fabricate asymmetric membranes. The effect of nanoparticle concentration (0-1 wt.%) on the morphology, roughness, wettability, porosity, permeability, and protein filtration performance of the membranes was investigated. The membrane containing 0.25 wt% nanoparticles exhibited the lowest water contact angle (67°) and surface roughness (10.4 ± 2.8 nm) compared to the other membranes. Moreover, this membrane exhibited the highest porosity (74%) and the highest pure water flux (398 L/m² h), which was 16% and 1.9 times higher than that of the pristine PES membrane. The modified PES membranes showed an improved antifouling ability, especially against irreversible fouling. Bovine serum albumin protein-based dynamic five-cycle filtration tests showed a maximum flux recovery ratio of 77% (cycle-1), 67% (cycle-2), and 65.8% (cycle-5) for the PES membrane containing 0.25 wt% nanoparticles. Overall, the biphasic Fe₂O₃-Mn₂O₃ nanoparticles were found to be an effective nanomodifier for improving the permeability and antifouling ability of PES membranes in protein separation and water treatment applications.

Surface tuned polyethersulfone membrane using an iron oxide functionalized halloysite nanocomposite for enhanced humic acid removal

Nanomodification of ultrafiltration (UF) membranes has been shown to be a simple and efficient technique for the preparation of high-performance membranes. In this work, an iron oxide functionalized halloysite nanoclay (Fe-HNC) nanocomposite was prepared and used as a nanofiller for polyethersulfone (PES) membranes. The effect of Fe-HNC concentration on the filtration performance of the membrane was investigated by varying the nanocomposite dosage (0-0.5 wt %) in the casting dope. Various characterization studies showed that the incorporation of Fe-HNC nanocomposites improved the membrane morphology and enhanced the surface properties, thermal stability, mechanical strength, hydrophilicity, and porosity. The permeability to pure water and filtration of humic acid (HA) were significantly improved by incorporating Fe-HNC into the PES membranes. The membrane with Fe-HNC loading of 0.1 wt % exhibited the highest pure water permeability (174.3 L/(m² h bar)) and removal of HA (90.1 %), which were 1.8 times and 29 % higher, respectively than the pristine PES membrane. Moreover, fouling studies showed the enhanced antifouling ability of the Fe-HNC nanocomposites modified PES membranes, especially against irreversible fouling. Continuous membrane regeneration-based fouling removal studies from HA showed that the PES/0.1 wt % Fe-HNC membrane exhibited a high fouling recovery of 70.4 % with very low reversible and irreversible fouling resistance of 9.61 % and 14.78 %, respectively, compared to the pristine PES membrane (fouling recovery: 40.4 %; reversible fouling: 21.7 %; irreversible fouling: 20.1 %). Overall, the Fe-HNC nanocomposite proved to be an effective nanomodifier for improving the permeability of PES membranes and the antifouling ability to treat HA polluted aqueous streams.

Fabrication of an antifouling PES ultrafiltration membrane via blending SPSF

Sulfonated polysulfone (SPSF) with different sulfonation degrees (10%, 30%, and 50%) was added to polyethersulfone (PES) to improve the separation and antifouling performance of polyethersulfone ultrafiltration membranes. The PES/SPSF blend ultrafiltration membrane was prepared by the non-solvent induced phase inversion method (NIPS), and the effect of sulfonation degree on the ultrafiltration performance was studied. The compatibility of SPSF and PES was calculated by the group contribution method, and confirmed by differential scanning calorimetry (DSC). The morphology and surface roughness of the membrane were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM), the chemical composition of the membrane was analyzed by X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (FTIR), and the permeability and anti-fouling performance of the blend membrane were studied through filtration experiments. The research shows that the flux and anti-fouling performance of the blend membrane have been improved after adding SPSF. When the sulfonation degree of the SPSF is 30%, the pure water flux of the blend membrane can reach 530 L m⁻² h⁻¹, the rejection rate of humic acid (HA) is 93%, the flux recovery rate of HA increases from 69.23% to 79.17%, and the flux recovery rate of BSA increases from 72.56% to 83%.

The chemical structures of (a) PES and (b) SPSF.

Improved anti-organic fouling and antibacterial properties of PVDF ultrafiltration membrane by one-step grafting imidazole-functionalized graphene oxide

At present, membrane fouling is a thorny issue that limits the development of polyvinylidene fluoride (PVDF) composite membrane, which seriously affects its separation performance and service lifespan. Herein, an imidazole-functionalized graphene oxide (Im-GO) with hydrophilicity and antibacterial performance was synthesized, and it was used as a modifier to improve the anti-organic fouling and antibacterial properties of PVDF membrane. The anti-organic fouling test showed that the maximum flux recovery ratios against bovine serum albumin and humic acid were 88.9% and 94.5%, respectively. Conspicuously, the grafted imidazole groups could effectively prevent the bacteria from growing on the membrane surface. It was gratifying that the antibacterial modifier Im-GO was almost not lost from the hybrid membranes even by the ultrasonic treatment, which was different from the conventional release-killing antibacterial agents. Owing to the long-term anti-organic fouling and antibacterial properties, Im-GO/PVDF hybrid membranes exhibit a great application potential in the fields of rough separation and concentration of biomedical products.

Removal of Humic Acid Using 3-Methacryloxypropyl Trimethoxysilane Functionalized MWCNT Loaded TiO2/PES Hybrid Membrane

In the present work, a highly efficient mixed matrix membrane (MMM) for humic acid (HA) removal was developed. Multiwalled carbon nanotubes (MWCNTs) were functionalized in the presence of 3-methacryloxypropyl trimethoxysilane using the co-condensation method and were subsequently loaded with TiO2 (prepared via the sol-gel route). The as-prepared material was then incorporated into a PES polymer solution to prepare a fMWCNT-TiO2/PES hybrid membrane via non-solvent induced phase inversion. The microstructure of the membrane was characterized using Fourier transform infrared spectroscopy, atomic force microscopy, scanning electron microscopy, water contact angle, thickness, porosity, and pore size. The fMWCNT-TiO2/PES hybrid membrane was tested for the removal of HA and antifouling performance. The results show that the surface hydrophilicity of the membranes was greatly improved upon the addition of the fMWCNT-TiO2 particles. The results show that 92% of HA was effectively removed after 1 h of filtration. In comparison with pristine membrane, the incorporation of fMWCNT-TiO2 nanoparticles led to enhanced pure water flux (99.05 L/m2 h), permeate flux (62.01 L/m2 h), higher HA rejection (92%), and antifouling improvement (RFR: 37.40%, FRR: 86.02%). Thus, the fMWCNT-TiO2/PES hybrid membrane is considered to be a great potential membrane for the improvement of ultrafiltration membranes.

Prediction of the phenol removal capacity from water by adsorption on activated carbon

High-performance sulfonated polysulfone (SPSf) mixed-matrix membranes (MMMs) were fabricated via a nonsolvent-induced phase separation (NIPS) method using zeolitic imidazolate frameworks-67 (ZIF-67) as a crosslinker. Acid-base crosslinking occurred between the sulfonic acid groups of SPSf and the tertiary amine groups of the embedded ZIF-67, which improved the dispersion of ZIF-67 and simultaneously improved the membrane strzcture and permselectivity. The dispersion of ZIF-67 in the MMMs and the acid-base crosslinking reaction were verified by energy-dispersive X-ray spectroscopy (EDX), X-ray diffractometry (XRD), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The pore structure analysis of MMMs indicated that filling ZIF-67 into SPSf enhanced the average surface pore sizes, surface porosities and more micropore in cross-sections. The crossflow filtrations showed the MMMs have higher pure water fluxes (57 to 111 L m^-2 h^-1) than the SPSf membrane (55 L m^-2 h^-1) but also higher bovine serum albumin (BSA) rejection rate of 93.9-95.8%, a model protein foulant. The MMMs showed a higher water contact angle than the SPSf membrane due to the addition of hydrophobic ZIF-67 and acid-base crosslinking, and also maintained high thermal stability evidenced by the thermogravimetric analysis (TGA) results. At the optimal ZIF-67 concentration of 0.3 wt%, the water flux of the SPSf-Z67-0.3 membrane was 82 L m^-2 h^-1 with a high BSA rejection rate of 95.3% at 0.1 MPa and better antifouling performance (FRR = 70%).

Influence of Polymer Solvents on the Properties of Halloysite-Modified Polyethersulfone Membranes Prepared by Wet Phase Inversion

Ultrafiltration polyethersulfone (PES) membranes were prepared by wet phase inversion. Commercial halloysite nanotubes (HNTs) in the quantities of 0.5 wt% vs. PES (15 wt%) were introduced into the casting solution containing the polymer and different solvents: N,N-dimethylformamide (DMF), N,N-dimethylacetamide (DMA), or 1-methyl-2-pyrrolidinone (NMP). The type of solvent influenced the membranes' morphology and topography, as well as permeability, separation characteristics, and antifouling and antibacterial properties. The membranes prepared using DMA exhibited the loosest cross-section structure with the thinnest skin and the roughest surface, while the densest and smoothest were the DMF-based membranes. The advanced contact angles were visibly lower in the case of the membranes prepared using DMF compared to the other solvents. The highest water permeability was observed for the DMA-based membranes, however, the most significant effect of the modification with HNTs was found for the NMP-based series. Regardless of the solvent, the introduction of HNTs resulted in an improvement of the separation properties of membranes. A noticeable enhancement of antifouling performance upon application of HNTs was found only in the case of DMF-based membranes. The study of the antibacterial properties showed that the increase in surface roughness had a positive effect on the inhibition of E. coli growth.

Fabrication of a Dual-Action Membrane with Both Antibacterial and Anticoagulant Properties via Cationic Polyelectrolyte-Induced Phase Separation

The development of microorganisms and formation of thrombus on a biomaterial surface can seriously lead to device failure and threaten human health. Nonetheless, a surface that has both antibacterial and anticoagulant properties has scarcely been developed. Herein, a novel dual-action membrane composed of polyethersulfone (PES) bulk material and a hydrophilic anionic poly-2-acrylamido-2-methylpropanesulfonic acid (PAMPS) polymer has been prepared via the cationic antibacterial agent poly(hexamethylene biguanide) (PHMB)-induced phase separation technique. Interestingly, the resultant membrane can offer tunable antibacterial and anticoagulant properties, while maintaining satisfactory permeability and greatly increasing selectivity. The membrane also shows excellent hydrophilicity, a well-defined porous surface, and cross section with a sponge gradient structure. Furthermore, the PHMB-PAMPS complex formed on the membrane surface displays outstanding long-term stability, which is crucial for further practical applications. More importantly, the hollow fiber membrane fabricated by the cationic polyelectrolyte-induced phase separation technique confirms its capability to control the membrane permeability (257.4 L·m^-2·h^-1·bar^-1) and selectivity (95.9%) without destroying the membrane structure. The present work opens a straightforward and efficient avenue for the rational design of a functional surface to fight biomedical material-associated infections.

Polyvinylidene fluoride (PVDF)-α-zirconium phosphate (α-ZrP) nanoparticles based mixed matrix membranes for removal of heavy metal ions

The removal of heavy metal ions from industrial wastewater is essential as they pose serious threats to human health and the environment. In this study, novel poly(vinylidene fluoride) (PVDF)-alpha-zirconium phosphate (PVDF-α-ZrP) mixed matrix membranes (MMM) were prepared via the phase inversion method. Membranes with different α-ZrP nanoparticles (NPs) loadings (0.25, 0.50, 0.75, or 1.00 wt%) were fabricated. The impacts of α-ZrP NP loading on the membrane's morphology, functionality, surface charge, and hydrophilicity were evaluated. Fourier-transform infrared and the energy-dispersive X-ray spectroscopy were performed to verify the presence of α-ZrP NPs in the fabricated membranes. The PVDF membranes became more hydrophilic after incorporating the α-ZrP NPs. The thermal and mechanical stability and porosity of the PVDF-α-ZrP MMM were higher than those of the pristine PVDF membrane. The increased hydrophilicity, pore size and porosity and reduced surface roughness of the PVDF-α-ZrP membrane led to significant flux increase and reduced fouling propensity. The PVDF-α-ZrP membrane containing 1.00 wt% α-ZrP was capable of removing 42.8% (Cd²⁺), 93.1% (Cu²⁺), 44.4% (Ni²⁺), 91.2% (Pb²⁺), and 44.2% (Zn²⁺) from an aqueous solution at neutral pH during filtration.

A novel polyethersulfone/modified activated carbon fiber composite membrane: potential for removal micropollutants from water under the electric field

This study aimed to develop a novel composite membrane based on polyethersulfone (PES) and modified activated carbon fibers (ACFs) to remove of sulfamethoxazole (SMZ) from water. The modification of ACFs was conducted by using acid, Fe, and Mn and was confirmed by Fourier transform infrared spectroscopy (FT-IR), energy dispersive X-ray spectroscopy (EDS), and water contact angle measurement. Later on, the composite membranes were prepared using PES (9 wt%), N-N-dimethylacetamide (DMAc) (75 wt%), polyethylene pyrrolidone (PVP) (5 wt%), anhydrous lithium chloride (LiCl) (1 wt%), and various types of modified ACFs (0.8 wt%) as additives. It was found that the contact angle of the membrane decreased by more than 20°, and the zeta potential decreased by more than 10 mV. ACF modified by Fe was used as an admixture, membrane obtained the high comprehensive performance. Especially bovine serum albumin (BSA) rejection rate and flux recovery ratio (FRR) reached 98.8% and 98.4%, respectively. And the removal rates of SMZ increased by 24.6% under the electric field. The degradation products were detected by high-performance liquid chromatography/mass spectrometry (HPLC/MS). Based on this result, the possible degradation pathways of SMZ are proposed.

The hierarchical flower-like MoS2 nanosheets incorporated into PES mixed matrix membranes for enhanced separation performance

Membrane fouling is an issue of concern due to the hydrophobic properties of polyethersulfone (PES) membrane when applied in water treatment. In this work, a facile hydrothermal method was utilized to synthesize hierarchical flower-like structured molybdenum disulfide nanosheets (HF-MoS2 NSs) that then incorporated into PES membranes as composite membranes. We characterized their permeability, the separation performance, the antifouling performance, and the antibacterial activity systematically. Results showed that composite membranes exhibited a better pure water flux (286 LMH/bar) at the HF-MoS₂ NSs content of 0.4 wt%, which was 1.8 times higher than the control membrane. Also, composite PES membranes achieved 98.2% and 96.9% rejection of BSA and HA in comparison with the control PES membrane (87.3%, and 84.5%, respectively). Compare to the control PES membrane, the flux recovery ratio of the composite membrane increased from 69% to 88% for BSA fouling and increased from 84% to 93% for HA fouling. The retention rate for the organic dyes also improved slightly after HF-MoS2 NSs incorporation into the membrane. Additionally, the composite membranes exhibited a relatively high antibacterial activity against E. coli and B. subtilis with antibacterial rates of 67.8% and 82.5%, respectively. In conclusion, HF-MoS2 NSs incorporated composite membranes were shown to have outstanding filtration performance and could be a promising candidate for practical application in water filtration.

Assessment of sulfonated homo and co-polyimides incorporated polysulfone ultrafiltration blend membranes for effective removal of heavy metals and proteins

Sulfonated homo and co- polyimide (sPI) were synthesized with new compositional ratios, and used as additives (0.5 wt%, 0.75 wt%, and 1.0 wt%) to prepare blend membranes with polysulfone (PSf). Flat sheet membranes for ultrafiltration (UF) were casted using the phase inversion technique. Surface morphology of the prepared UF membranes were characterized by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Surface charge of the membranes were determined by zeta potential, and hydrophilicity was studied by contact angle measurement. The contact angle of the membrane decreased with increasing sPI additive indicates increasing the hydrophilicity of the blend membranes. Filtration studies were conducted for rejection of heavy metals (Pb2+ and Cd2+) and proteins (pepsin and BSA). Blend membranes showed better rejection than pure PSf membrane. Among the blend membranes it was observed that with increasing amount of sPIs enhance the membrane properties and finally, PSf-sPI5 membrane with 1 wt% of sPI5 showed the improved permeability (72.1 L m-2 h-1 bar-1), and the best rejection properties were found for both metal ions (≈98% of Pb2+; ≈92% of Cd2+) and proteins (>98% of BSA; > 86% of Pepsin). Over all, this membrane was having better hydrophilicity, porosity and higher number of sites to attach the metal ions. Its performance was even better than several-reported sulfonic acid based UF membranes. All these intriguing properties directed this new UF membrane for its potential application in wastewater treatment.

Enhanced permeability, mechanical and antibacterial properties of cellulose acetate ultrafiltration membranes incorporated with lignocellulose nanofibrils

Cellulose acetate (CA) ultrafiltration membranes are attracting more attention in wastewater purification due to its biodegradability and eco-friendly. The application of CA membranes, however, is limited by high susceptibility to bacterial corrosion and lack of mechanical tolerance that results in loss of life. To solve the above problems, we first fabricated the CA-based composite membranes incorporated with bamboo-based lignocellulose nanofibrils (LCNFs) by a strategy of phase inversion. LCNFs was prepared by using a combined method of one-step chemical pretreatment and acid hydrolysis coupled with high-pressure homogenization. The as-prepared CA/LCNFs composite membranes with 4 wt% lignin in the LCNFs exhibited high tensile strength of 7.08 MPa and strain-at-break of 12.21%, and high filtration permeability of 188.23 L·m^-2·h^-1 as ultrafiltration membranes for wastewater treatment, which could obviously inhibit the growth of Escherichia coli.

Preparation of thermo-responsive PNIPAAm-MWCNT membranes and evaluation of its antifouling properties in dairy wastewater

A novel MWCNT-PNIPAAm nanocomposite membrane was developed with an excellent cleaning efficiency of thermo-responsive surface. The thermo-responsive N-isopropyle acryleamide (NIPAAm) monomer was polymerized on the surface of MWCNT via free radical polymerization. The prepared MWCNT-PNIPAAm nanocomposite was characterized by FTIR, SEM and TGA analyses. Various amounts of the prepared nanocomposite were incorporated into the membrane matrix by the physical blending method. The resultant membranes showed better surface wettability and pure water flux compared to pristine Polyethersulfone (PES) membrane. Furthermore, after filtration, the COD value of dairy wastewater was reduced to around 90% for all membranes. The thermo-responsive cleaning method was employed to investigate the cleaning efficiency of MWCNT-PNIPAAm membrane for dairy wastewater. The 99.9% flux recovery ratio was obtained for MWCNT-PNIPAAm-0.05% membranes. All these results confirmed that the presence of MWCNT-PNIPAAm nanocomposite in the membrane matrix improves the membrane hydrophilicity and antifouling properties.

Development of an HKUST-1 Nanofiller-Templated Poly(ether sulfone) Mixed Matrix Membrane for a Highly Efficient Ultrafiltration Process

Mixed-matrix membranes (MMMs) have been drawing increasing attention due to the high permeability and high rejection capabilities for highly efficient wastewater treatment applications. Nonetheless, improving the water permeance while maintaining the high rejection capability is still an ongoing challenge for the practically state-of-the-art MMMs. Herein, a new class of poly(ether sulfone) (PES) based MMM containing metal-organic framework (MOF) nanofillers of HKUST-1 and blending with poly(methyl methacrylate- co-methacrylic acid) (PMMA- co-MAA) copolymer, designated as HKUST-1@mPES MMM, were developed for the highly efficient ultrafiltration (UF) process. In this study, the nanosized HKUST-1 nanofillers were removed by water dissolution as sacrificial templating materials, so that the additional nanovoids were deliberately generated throughout the dense polymer matrix. The introduction of PMMA- co-MAA copolymer facilitated the even dispersion of HKUST-1 nanofillers in a polymer matrix, by constructing the bridge connection between inorganic nanofillers and organic matrix. The resultant HKUST-1@mPES MMM exhibited a high pure water permeability (PWP) up to 490 L·m^-2·h^-1·bar^-1, substantially reaching nearly 3 times higher than that of the mPES membrane without HKUST-1 nanofillers loading and maintaining a relatively high BSA rejection rate of 96% without obvious deterioration. The newly developed HKUST-1@mPES MMM thereby exhibited a comparable separation efficiency compared to the cutting-edge UF membranes reported so far. Overall, the nanovoid-generated approach provides new insight into developing advanced MMMs used for highly efficient water treatment applications.

Fabricating PES/SPSF membrane via reverse thermally induced phase separation (RTIPS) process to enhance permeability and hydrophilicity

A new method was presented to prepare hydrophilic PES/SPSF flat-sheet membrane by a reverse thermally induced phase separation (RTIPS) method to enhance permeability and hydrophilicity. SPSF was self-made and was blended to improve the hydrophilicity of PES flat-sheet membrane. The performance of PES/SPSF flat-sheet membrane, which varied with SPSF content and coagulation water bath temperature, was investigated by SEM, FTIR, AFM, pure water flux, BSA rejection rate, water contact angle and long-term testing. FTIR results proved the successful blending of SPSF with PES membrane, SEM images showed that dense skin surface and finger-like structure emerged in the membrane fabricated by NIPS method, while a porous top surface and sponge-like structure emerged in the membrane fabricated by RTIPS. The pure water flux and BSA rejection rate of the membrane for RTIPS were both higher than those for NIPS. AFM images revealed that surface roughness increased with the addition of SPSF. The water contact angle decreased with the increase of SPSF, which illustrated better hydrophilicity with the addition of SPSF. The flat-sheet PES membrane prepared with 2 wt% SPSF by RTIPS method exhibited decent properties, reaching maximum pure water flux (966 L m⁻² h⁻¹) and at the same time the BSA rejection rate was 79.2%. The long-term test proved that the anti-fouling performance of PES/SPSF membrane was better than that of PES membrane.

A new method is presented to prepare hydrophilic PES/SPSF flat-sheet membrane by a reverse thermally induced phase separation (RTIPS) method to enhance permeability and hydrophilicity.