In situ microwave-assisted oxidation of graphite into partially oxidized graphite nanoparticles for microwave-sorptive removal of anionic and cationic dyes

Enhanced removing of phosphate ions from agricultural drainage wastewater by using microwave-assisted synthesized attapulgite (Fullers earth) @carboxymethylcellulose nanocomposite

Contamination of various water resources with phosphate pollutant owing to the excessive use of phosphate fertilizers was labeled by dangerous consequences. Most of the water remediation methods are not efficient for phosphate recovery and always generate secondary wastes. Therefore, the current study is aimed to prepare a novel ecofriendly and sustainable APT500@CMC nanocomposite via simple covalent binding of thermally treated attapulgite clay at 500 °C (APT500) with carboxymethyl cellulose (CMC) using microwave irradiation process. The assembled nanocomposite was confirmed by diverse techniques. The optimum conditions for efficient 10, 25 and 50 mg/L PO43- removal were detected at pH 3, time 30 min, temperature 25 °C and mass 200 mg. The kinetic and isotherms were fitted both to a combination of pseudo 1st - 2nd orders and Langmuir model, while thermodynamic parameters verified PO43- removal via spontaneous and exothermic reaction behavior. The mode of interaction and binding of PO43- ions onto the surface of APT500@CMC were suggested via ion-pair interaction process. Excellent PO43- recovery (98.8 %) from real agricultural drainage wastewater was established. The explored APT500@CMC afforded good stability for five regeneration cycles. Therefore, the collected results confirm the validity of APT500@CMC for excellent removal of PO43- from real agricultural drainage wastewater.

Cr(VI) and doxorubicin adsorptive capture by a novel bionanocomposite of Ti-MOF@TiO2 incorporated with watermelon biochar and chitosan hydrogel

Biodegradable polymers, biochars and metal organic frameworks (MOFs) have manifested as top prospects for elimination of harmful pollutants. In the current study, Ti-MOF was synthesized and decorated with TiO2 nanoparticles, then embedded into watermelon peel biochar and functionalized with chitosan hydrogel to produce Ti-MOF@TiO2@WMPB@CTH. Various instruments were employed to assure the effective production of the bionanocomposite. The HR-TEM and SEM studies referred to excellent surface porosity and homogeneity of Ti-MOF@TiO2@WMPB@CTH bionanocomposite, with 51.02-74.23 nm. Based on the BET analysis, the mesoporous structure has a significant surface area of 366.04 m2 g-1 and a considerable total pore volume of 11.38 × 10-2 cm3 g-1, with a mean pore size of 12.434 nm. Removal of doxorubicin (DOX) and hexavalent chromium (Cr(VI)) was examined under various experimentations. Pseudo-second order kinetic models in addition to Langmuir isotherm offered the best fitting. Thermodynamic experiments of the two contaminants demonstrated spontaneous and endothermic interactions. After five subsequent adsorption and desorption cycles, Ti-MOF@TiO2@WMPB@CTH bionanocomposite demonstrated an exceptional recyclability for the elimination of DOX and Cr(VI) ions, reaching 97.96 % and 95.28 %, respectively. Finally, the newly designed Ti-MOF@TiO2@WMPB@CTH bionanocomposite demonstrated a high removing efficiency of Cr(VI) ions and DOX from samples of real water.

Removal of the Anionic Dye Congo Red from an Aqueous Solution Using a Crosslinked Poly(vinyl alcohol)-ZnO-Vitamin M Nanocomposite Film: A Study of the Recent Concerns about Nonlinear and Linear Forms of Isotherms and Kinetics

This paper deals with the preparation, characterization, and application of a crosslinked poly(vinyl alcohol)/ZnO-vitamin M (PVA/ZnO-VM) nanocomposite film for the removal of Congo red (CR) from an aqueous solution. The characterization of a crosslinked PVA/ZnO-VM nanocomposite film showed that the structure became more regular and also the surface morphology appeared smooth in comparison with pure PVA. The obtained data from Brunauer-Emmett-Teller (BET) proved the mesoporous structure for this nanocomposite film. Several effective factors were examined for the adsorption ability of the nanocomposite film, including solution pH (2-10), sorbent amount (0.02-0.08 g), contact time (3-240 min), initial concentration of the adsorbate (30-300 mg·L^-1), and temperature (318-358 K). The optimal conditions are as follows: pH = 10, adsorbent amount = 0.06 g, and C₀ = 200 mg·L^-1. The removal efficiency of the nanocomposite film was 92% after 4 h at the ambient temperature. To interpret the adsorption process, nonlinear and linear forms of kinetic and isotherm models were considered. The obtained data followed nonlinear pseudo-second-order and linear Langmuir isotherm models, which indicated the monolayer formation of CR over the crosslinked PVA/ZnO-VM nanocomposite film with the maximum adsorption capacity of about 56.49 mg·g^-1. Also, the adsorption process of CR by the crosslinked PVA/ZnO-VM nanocomposite film is a spontaneous and exothermic reaction.

Adsorption behavior of silver quantum dots by a novel super magnetic CoFe2O4-biochar-polymeric nanocomposite

Recent industrial development and research progress in nanotechnology have led to the release of a number of nanomaterials with particle sizes (1-10 nm) which are categorized as quantum dots (QDs) in aquatic system. Disposal away of such QDs will cause potential pollution to the environment. Therefore, removal of disposed QDs from wastewater represents a challenging research subject for scientists and engineers. Hence, the objective of this study is devoted to assess the process of coagulative removal of silver quantum dots (Ag-QDs), as an example, from water by a novel super magnetic nanocomposite. Such material was aimed to prepare from the chemical combination and reaction of a generated Citrus sinensis and Citrus reticulata peels biochar (SMCsr-B) with spinel cobalt ferrite (CoFe₂O₄) as a super-magnetic source. The produced (SMCsr-B) was then crosslinked with polyurea-formaldehyde polymer (PUF) using EDA in only two minutes via microwave irradiation to produce (SMCsr-B/PUF). The SEM, EDX, FT-IR, XRD, and XPS analyses of the assembled (SMCsr-B/PUF) nanocomposite were acquired to confirm surface morphology and chemical structure. Controlling experimental factors were investigated as pH, time, and Ag-QDs pollutant concentration using microwave irradiative removal technique to establish the efficiency of coagulative adsorption of Ag-QDs onto (SMCsr-B/PUF). The solution (pH 5) was proved to exhibit the higher removal percentages of Ag-QDs in 15-25 s. SMCsr-B/PUF nanocomposite exhibited high removal efficiency as 93.12%, 92.39% and 92.48% upon using 20, 40 and 60 mg L^-1 of Ag-QDs, respectively in presence of 10 mM NaCl. The kinetic and equilibrium adsorption data were best fitted to Freundlich model. The prepared SMCsr-B/PUF was successfully utilized as an efficient super magnetic nanocomposite for removal and recovery of Ag-QDs from aqueous environment.

Green fabrication of ZnO nanoparticles using Eucalyptus spp. leaves extract and their application in wastewater remediation

The present study explored removal of carcinogenic cationic and anionic dyes from aqueous medium using green fabricated zinc oxide nanoparticles (ZnO-NPs). The ZnO-NPs were synthesized employing biogenic green reduction and precipitation approach. The characterization of ZnO NPs was done using various techniques such as FESEM, XRD, BET, TGA, HRTEM, EDX, and FTIR. All experiments were conducted in batch mode. Maximum removal was achieved at pH 6.0 and pH 8.0 for Congo Red (CR) and Malachite Green (MG) dyes respectively. Dye adsorption process showed better fit with Langmuir and Temkin isotherm models for CR dye and MG dye respectively. Maximum adsorption capacity of ZnO NPs was 48.3 mg/g for CR dye and 169.5 mg/g for MG dye. The dye adsorption followed pseudo-second order model and values of thermodynamic parameters confirmed that the adsorption process was spontaneous and favourable. Reusability efficiency of the nanoparticle was explored using ethanol and water and based on results it was inferred that ZnO-NPs can be reused for dye removal. Effect of salinity on the removal of CR and MG dyes was also explored and found that presence of salinity in aqueous medium have adverse impact on the dye removal efficiency of ZnO-NPs.