Polydopamine as an intermediate layer for silver and hydroxyapatite immobilisation on metallic biomaterials surface

Fabrication of PTFE + TiO2/Ag coatings on 316L/polydopamine with advanced mechanical, bio-corrosion, and antibacterial properties for stainless steel Catheters

This study explores the corrosion resistance and antibacterial properties of a PTFE + TiO2/Ag coating applied to 316 L stainless steel. To enhance adhesion, a polydopamine interlayer was chemically deposited onto the steel surface. The PTFE + TiO2 coating was subsequently applied through immersion, followed by the deposition of silver nanoparticles using a chemical method. Optimization of the polydopamine interlayer involved varying temperature, time, stirring speed, and drying parameters. The optimal conditions for the polydopamine interlayer were determined to be 60 °C for 1 h, 300 rpm stirring, and 24-h drying in a freeze dryer. Analytical results demonstrated that both the PTFE + TiO2 and PTFE/PTFE + TiO2/Ag coatings exhibited exceptional corrosion resistance, with corrosion currents of 3.3 × 10-5 and 3.2 × 10-4 μA/cm2, respectively. Antibacterial assessments showcased the remarkable ability of the PTFE/PTFE + TiO2/Ag coating, containing 5% silver content, to effectively inhibit bacterial penetration within a 6.5 mm radius. Furthermore, this coating displayed a water contact angle of 143°, classifying it as a hydrophobic coating. The photocatalytic efficiency (Rs) was determined to be 3.18 × 10-3 A/W, a performance level comparable to that of a standard UV sensor. These findings underscore the substantial enhancements in corrosion resistance, antibacterial performance, and hydrophobic characteristics achieved with the PTFE + TiO2/Ag coating, particularly through the novel optimization of the polydopamine interlayer. This coating exhibits great promise for multifunctional protective applications in diverse fields, particularly demonstrating its suitability for implants and bio-coatings.

Conferring NiTi alloy with controllable antibacterial activity and enhanced corrosion resistance by exploiting Ag@PDA films as a platform through a one-pot construction route

The lack of antibacterial activity and the leaching of Ni ions seriously limit the potential applications of the near equiatomic nickel-titanium (NiTi) alloy in the biomedical field. In this study, a silver nanoparticles (Ag NPs) wrapped in a polydopamine (Ag@PDA) film modified NiTi alloy with controllable antibacterial activity and enhanced corrosion resistance was achieved using a one-pot approach in a mixed solution of AgNO3 and dopamine. The controllable antibacterial activity could be achieved by adjusting the initial concentration of dopamine (Cdop), which obtained Ag@PDA films with varying thickness of polydopamine layers coated on Ag NPs, thereby conferring different levels of antibacterial activity to the modified NiTi alloy. In vitro antibacterial ratios (24 h) of Ag@PDA film-modified NiTi alloy against E.coli and S.aureus ranged from 46 % to 100 % and from 42 % to 100 %, respectively. The release curves of Ag ions indicated the persistent antibacterial effect of Ag@PDA film-modified NiTi alloy for at least 21 days. Moreover, in vitro cytotoxicity and in vivo implantation tests demonstrated the satisfactory biosafety of the Ag@PDA film-modified NiTi alloy when used as bioimplants. This research offers valuable insight into meeting various antibacterial demands for NiTi alloy implantations and highlights the potential of Ag-containing film-modified biomaterials in addressing different types of infections induced by implantations.

Mussel-inspired antimicrobial hydrogel with cellulose nanocrystals/tannic acid modified silver nanoparticles for enhanced calvarial bone regeneration

Bacterial infection is a serious challenge in the treatment of open bone defects, and reliance on antibiotic therapy may contribute to the emergence of drug-resistant bacteria. To solve this problem, this study developed a mineralized hydrogel (PVA-Ag-PHA) with excellent antibacterial properties and osteogenic capabilities. Silver nanoparticles (CNC/TA@AgNPs) were greenly synthesized using natural macromolecular cellulose nanocrystals (CNC) and plant polyphenolic tannins (TA) as stabilizers and reducing agents respectively, and then introduced into polyvinyl alcohol (PVA) and polydopamine-modified hydroxyapatite (PDA@HAP) hydrogel. The experimental results indicate that the PVA-Ag-PHA hydrogel, benefiting from the excellent antibacterial properties of CNC/TA@AgNPs, can not only eliminate Staphylococcus aureus and Escherichia coli, but also maintain a sustained sterile environment. At the same time, the HAP modified by PDA is uniformly dispersed within the hydrogel, thus releasing and maintaining stable concentrations of Ca2+ and PO43- ions in the local environment. The porous structure of the hydrogel with excellent biocompatibility creates a suitable bioactive environment that facilitates cell adhesion and bone regeneration. The experimental results in the rat critical-sized calvarial defect model indicate that the PVA-Ag-PHA hydrogel can effectively accelerate the bone healing process. Thus, this mussel-inspired hydrogel with antibacterial properties provides a feasible solution for the repair of open bone defects, demonstrating the considerable potential for diverse applications in bone repair.

A surface metal ion-modified 3D-printed Ti-6Al-4V implant with direct and immunoregulatory antibacterial and osteogenic activity

The high concentration of antibacterial metal ions may exhibit unavoidable toxicity to cells and normal tissues. The application of antibacterial metal ions to activate the immune response and induce macrophages to attack and phagocytose bacteria is a new antimicrobial strategy. Herein, 3D-printed Ti-6Al-4V implants modified by copper, and strontium ions combined with natural polymers were designed to treat implant-related infections and osseointegration disorders. The polymer-modified scaffolds rapidly released a large amount of copper and strontium ions. During the release process, copper ions were employed to promote the polarization of M1 macrophages, thus inducing a proinflammatory immune response to inhibit infection and achieve the immune antibacterial activity. Meanwhile, copper and strontium ions promoted the secretion of bone-promoting factors by macrophages, induced osteogenesis and showed immunomodulatory osteogenesis. This study proposed immunomodulatory strategies based on the immunological characteristics of target diseases and provided ideas for the design and synthesis of new immunoregulatory biomaterials.

Chitosan coated fluorescent mesoporous silica for the sensitive and selective detection of H2O2

A novel turn-on fluorescent sensor for hydrogen peroxide (H₂O₂) was prepared from chitosan (CS) coating mesoporous silica nanoparticles (MSNs) loaded with 1-(4-Aminophenyl)-1,2,2-triphenylethene (TPE-NH₂) and silver nanoparticles (AgNCs). The surface of MSNs was coated by CS as the gatekeeper and the template for loading of AgNCs. Because of the surface plasmon-enhanced energy transfer (SPEET), AgNCs effectively quenched the fluorescence emission of nanoparticles. In the presence of H₂O₂, AgNCs can be oxidized to Ag⁺, resulting in the recovery of fluorescence. This fluorescent sensor was characterized with respect to its chemical composition, morphological features and optical properties by means of FTIR, XRD, TGA, SEM, TEM, XPS, UV-Vis and fluorescence spectroscopy. The MSN/TPE-CS@Ag nanoparticles showed good sensitivity and selectivity for H₂O₂ even with various interfering ions and agents. Under optimized conditions, the detection limit for H₂O₂ was 0.64 μM in the rage of 1-300 μM. The feasibility of the practical application of this probe was confirmed by accurate quantitative of H₂O₂ in practical samples.

Plasmon-Enhanced Electrocatalysis of Conductive Polymer-Based Nano-Heterojunction for Small Molecule Metabolites Diagnostics

Conductive polymers are promising electrode candidates in the nonenzymatic catalytic detection of small molecule metabolites, due to the tunable electronic conductivity and versatile modifiability. However, the complex catalytic reaction pathway of conductive polymers results in lower detection sensitivity and a narrower linear range compared with clinical metal-based and carbon-based electrodes. Localized surface plasmon resonance (LSPR), characterized by deep strong light-matter coupling, has great potential in driving surface catalytic reactions at an ultrafast rate. Here, we constructed a salix argyracea-like polypyrrole nanowires/silver nanoparticles (PPy/AgNPs) heterojunction electrode using polydopamine as a dopant and chelator. Through cyclic voltammetry, the Mott-Schottky curve, and COMSOL simulation, we demonstrated that the LSPR-excited photocarriers enhanced PPy/AgNPs electrode electrocatalysis. Thus, the detection current response and linear range were significantly improved under the LSPR excitation when taking glucose and hydrogen peroxide as models of small molecule metabolites. Furthermore, we discussed the LSPR-enhanced detection mechanism of PPy/AgNPs electrode from the aspects of the Tafel slope, the apparent electron diffusion coefficient, and the charge transfer resistance. This strategy opens a new avenue toward the design of LSPR-enhanced conductive polymer electrodes.

Photothermal-Controlled Release of IL-4 in IL-4/PDA-Immobilized Black Titanium Dioxide (TiO2) Nanotubes Surface to Enhance Osseointegration: An In Vivo Study

Host immune response has gradually been accepted as a critical factor in achieving successful implant osseointegration. The aim of this study is to create a favorable immune microenvironment by the dominant release of IL-4 during the initial few days after implant insertion to mitigate early inflammatory reactions and facilitate osseointegration. Herein, the B-TNT/PDA/IL-4 substrate was established by immobilizing an interleukin-4 (IL-4)/polydopamine (PDA) coating on a black TiO₂ nanotube (B-TNT) surface, achieving on-demand IL-4 release under near infrared (NIR) irradiation. Gene Ontology (GO) enrichment analyses based on high-throughput DNA microarray data revealed that IL-4 addition inhibited osteoclast differentiation and function. Animal experiment results suggested that the B-TNT/PDA/IL-4+Laser substrate induced the least inflammatory, tartrate-resistant acid phosphatase, inducible nitric oxide synthase and the most CD163 positive cells, compared to the Ti group at 7 days post-implantation. In addition, 28 days post-implantation, micro-computed tomography results showed the highest bone volume/total volume, trabecular thickness, trabecular number and the lowest trabecular separation, while Hematoxylin-eosin and Masson-trichrome staining revealed the largest amount of new bone formation for the B-TNT/PDA/IL-4+Laser group. This study revealed the osteoimmunoregulatory function of the novel B-TNT/PDA/IL-4 surface by photothermal release of IL-4 at an early period post-implantation, thus paving a new way for dental implant surface modification.

Antibiotics- and Heavy Metals-Based Titanium Alloy Surface Modifications for Local Prosthetic Joint Infections

Prosthetic joint infection (PJI) is the second most common cause of arthroplasty failure. Though infrequent, it is one of the most devastating complications since it is associated with great personal cost for the patient and a high economic burden for health systems. Due to the high number of patients that will eventually receive a prosthesis, PJI incidence is increasing exponentially. As these infections are provoked by microorganisms, mainly bacteria, and as such can develop a biofilm, which is in turn resistant to both antibiotics and the immune system, prevention is the ideal approach. However, conventional preventative strategies seem to have reached their limit. Novel prevention strategies fall within two broad categories: (1) antibiotic- and (2) heavy metal-based surface modifications of titanium alloy prostheses. This review examines research on the most relevant titanium alloy surface modifications that use antibiotics to locally prevent primary PJI.

Electrodeposited dopamine/strontium-doped hydroxyapatite composite coating on pure zinc for anti-corrosion, antimicrobial and osteogenesis

Zinc-based biometal is expected to become a new generation of biodegradable implants. Due to its antibacterial and biocompatibility in vivo, zinc metals is recently considered to be the most promising biodegradable metal, However, cytotoxicity is the thorny problem that currently restrict its application, due to the excessive Zn ions released during degradation. In order to solve these problems, dopamine modified strontium-doped hydroxyapatite coating (SrHA/PDA) was fabricated on alkali-treated pure zinc to improve its corrosion rate and cytocompatibility by electrodeposition for the first time. The obtained coating showed a dense structure and high crystallinity, which was attributed to the attraction of Ca²⁺ ions by polydopamine. The results showed that the SrHA/PDA coating delayedthe degradation rate of zinc metal, which reduced the release of Zn²⁺, thereby reducing its cytotoxicity. Additionally, electrochemical tests showed that SrHA/PDA coating can reduce the corrosion rate of pure zinc. In vitro cell viability showed that even at high Zn²⁺ concentrations (3.11 mg/L), preosteoblasts (MC3T3-E1) cells proliferated at a high rate on SrHA/PDA, thus confirming that Sr²⁺ counteracted the cytotoxic effects of Zn²⁺ and promoted cell differentiation. Moreover, the SrHA/PDA coating still maintained excellent antibacterial effects against pathogenic bacterial strains (Escherichia coli and Staphylococcus aureus). Mild pH changes had no significant effect on the viability of cells and bacterias. Collectively, the present study elucidated that by coating SrHA/PDA/Zn(OH)₂ on Zn, a controllable corrosion rate, original antibacterial properties and better cell compatibility can be achieved. This provided a new strategy for the surface modification of biodegradable Zn.

A novel dental adhesive containing Ag/polydopamine-modified HA fillers with both antibacterial and mineralization properties

OBJECTIVES

To evaluate the antibacterial and mineralization properties of a dental adhesive containing Ag/polydopamine-modified HA (HA, hydroxyapatite) fillers.

METHODS

First, an HA-polydopamine-Ag-polydopamine (HA-PDA-Ag-PDA) filler was prepared and characterized using SEM, TEM, XPS, XRD and FTIR. Then, the HA-PDA-Ag-PDA filler was mixed into an adhesive at different mass fractions (0 wt%, 0.5 wt%, 1 wt%, 2 wt%) to prepare a functional adhesive. Antibacterial and mineralization tests were carried out, and the cytotoxicity of the functional adhesive against L929 fibroblasts was also examined.

RESULTS

The SEM, TEM, XPS, XRD and FTIR characterizations confirmed the successful preparation of the HA-PDA-Ag filler. The 1 wt% and 2 wt% functional adhesives showed the strongest bacterial inhibition effect among all the samples (p < 0.05). Obvious apatite crystals were observed in the SEM micrograph of the surface of the functional adhesive sample after immersion in artificial saliva for predetermined times (1 d, 7 d, 14 d and 28 d). There was no significant difference between the experimental group and the control group in terms of cell proliferation activity (p > 0.05).

CONCLUSIONS

The 1 wt% and 2 wt% functional adhesives demonstrated good antibacterial and mineralization properties, as well as good biocompatibility.

CLINICAL SIGNIFICANCE

Functional adhesives containing Ag/polydopamine-modified HA fillers with antibacterial and mineralization capabilities might have excellent potential to enhance the stability and durability of hybrid layers and prolong the service life of dental restorations. Our study on bifunctional adhesives has paved the way for future clinical applications to increase restoration longevity.

Mussel-inspired antimicrobial coating on PTFE barrier membranes for guided tissue regeneration

Guided tissue regeneration procedures to treat periodontitis lesions making use of polytetrafluoroethylene (PTFE) membranes exhibit large variability in their surgical outcomes, due to bacterial infection following implantation. This work reports on a facile method to obtain antimicrobial coatings for such PTFE membranes, by exploiting a mussel-inspired approach andin-situformation of silver nanoparticles (AgNPs). PTFE films were initially coated with self-polymerized 3,4-dihydroxy-DL-phenylalanine (DOPA) (PTFE-DOPA), then incubated with AgNO₃solution. In the presence of catechol moieties, Ag⁺ions reduced into Ag⁰, forming AgNPs of around 68 nm in the polyDOPA coating on PTFE membranes (PTFE-DOPA-Ag). The x-ray photoelectron spectroscopy, atomic force microscopy and scanning electron microscopy analyses indicated that the AgNPs were distributed quite homogeneously in the polymeric membrane. The antimicrobial ability of PTFE-DOPA-Ag membranes againstStaphylococcus aureusandEscherichia coliwas assessed.In vitrocell assay using NIH 3T3 fibroblasts showed that, although cells were adhered to PTFE-DOPA-Ag membranes, their viability and proliferation were limited demonstrating again the antibacterial activities of PTFE-DOPA-Ag membranes. This work provides proof-of-concept study of a new versatile approach for AgNPs coating, which may be easily applied to many other types of polymeric or metallic implants through exploiting the adhesive behavior of mussel-inspired coatings.

Quercetin as an Auxiliary Endodontic Irrigant for Root Canal Treatment: Anti-Biofilm and Dentin Collagen-Stabilizing Effects In Vitro

Bacterial reinfection and root fracture are the main culprits related to root canal treatment failure. This study aimed to assess the utility of quercetin solution as an adjunctive endodontic irrigant that does not weaken root canal dentin with commitment anti-biofilm activity and bio-safety. Based on a noninvasive dentin infection model, dentin tubules infected with Enterococcus faecalis (E. faecalis) were irrigated with sterile water (control group), and 0, 1, 2, 4 wt% quercetin-containing ethanol solutions. Live and dead bacteria percentages in E. faecalis biofilms were analyzed by confocal laser scanning microscopy (CLSM). Elastic modulus, hydroxyproline release and X-ray photoelectron spectroscopy (XPS) characterization were tested to evaluate the irrigants’ collagen-stabilizing effect. The cytotoxicity was tested by CCK-8 assay. Quercetin increased the proportion of dead bacteria volumes within E. faecalis and improved the flexural strength of dentin compared to control group (p < 0.05). Quercetin-treated dentin matrix had less elasticity loss and hydroxyproline release after collagenase degradation (p < 0.05). Moreover, quercetin solutions revealed an increase in the C-O peak area under both C1s and O1s narrow-scan spectra of XPS characterization, and no cytotoxicity (p > 0.05). Quercetin exhibited anti-biofilm activity, a collagen-stabilizing effect with cytocompatibility, supporting quercetin as a potential candidate for endodontic irrigant.

Inhibition of oral biofilm formation by zwitterionic nonfouling coating

Inhibition of oral biofilm formation is critical to prevent and treat dental caries and periodontal diseases. In this study, we synthesized zwitterionic poly(carboxybetaine) (pCB) based polymer as a nonfouling coating to provide anti-bacterial properties to tooth surfaces. Four catechol derived l-3,4-dihydroxyphenylalanine (DOPA) groups were conjugated to pCB to serve as a surface anchoring group. The pCB-(DOPA)₄ polymer was coated on the hydroxyapatite (HA) and enamel samples by simple immersion and characterized by Raman spectroscopy. The nonfouling effectiveness of the pCB based coating was determined by protein adsorption and bacterial adhesion assays. The coating was transparent on sample surfaces. The protein adsorption was significantly reduced to 8.2% and 6.9%, respectively, on pCB-(DOPA)₄ coated HA and enamel samples. The pCB-(DOPA)₄ -coated samples also demonstrated significantly fewer adhered Pseudomonas aeruginosa, Staphylococcus aureus, and Streptococcus mutants compared to the control. This novel coating material provides an innovative approach to resist biofilm formation on tooth surfaces and has great potential in future dental clinical applications.

Pulsed electrodeposition of Ag+ doped prosthetic Fluorohydroxyapatite coatings on stainless steel substrates

In order to reinforce the antibacterial character of fluorohydroxyapatite (FHA) prosthetic layers on 316L stainless steel (316L SS), Ag⁺ ions (an antibacterial agent) are included in the electrodeposition medium to be incorporated in the FHA layers created by pulsed protocol. The doped coatings (Ag-FHA) with different concentrations of silver ions (5, 10, 20, 40 and 100 ppm) were characterized electrochemically (polarization curves and electrochemical impedance spectroscopy) in simulated body fluid (SBF) solution and microbiologically against two pathogenic bacteria (Staphylococcus aureus and Escherichia coli). XPS, EDX and Raman spectroscopies were used to complement these evaluations. Whatever the concentration of incorporated Ag⁺ ions, the FHA morphology, structure and composition are not affected. The XPS and EDX results confirm the Ag⁺ presence within the apatite crystals, mostly concentrated at the extreme surface of the coatings. They also show the lowering of the stoichiometry of the coatings, confirmed by Raman analyses. The corrosion studies indicate that the prosthetic coatings act as a barrier against corrosion of the 316L SS alloy. Moreover, the results of the microbiological tests show that a content of 40 ppm of silver, introduced into the prosthetic coatings, inhibits the bacterial growth. Lower concentrations showing only a partial inhibition. In conclusion, using a pulsed current mode in the electrodeposition processes generates Ag-FHA/316L SS systems suitable for biomedical applications.

Polydopamine-modified interface improves the immobilization of natural bioactive-dye onto textile and enhances antifungal activity

Dermatomycosis, such as candidiasis and mycosis among others, has emerged recently as the most frequent fungal infection worldwide. This disease is due to the skin's exposure to microorganisms that are able to pass through skin barrier defects. Therefore, textiles in direct contact with skin can serve as a source of contamination and fungus spread. In the current study, a sustainable and eco-friendly method for antifungal cotton finishing using Curcuma longa L extracted from rhizomes was investigated. To enhance the natural bioactive dye uptake and attachment, cellulosic cotton fibers were chemically modified using dopamine, a biocompatible molecule, leading to the deposition of a hydrophilic layer of polydopamine. The efficiency of the polydopamine coating on the cotton surface has been assessed by x-ray photoemission spectroscopy analyses, with the detection of nitrogen, and by water contact angle for the wettability enhancement. Furthermore, characterization of the modified samples confirms that the modification did not affect either the cellulosic fiber morphology or the mechanical properties. The dyeability and bioactive dye immobilization were then assessed by colorimetry. Finally, the effectiveness of the finished fabrics against Trichophyton (rubrum/mentagrophytes) and Candida albicans strains was evaluated and was shown to induce growth inhibition mainly on Candida albicans strains.

Effects of polydopamine-passivation on the optical properties of carbon dots and its potential use in vivo

Passivation of carbon dots via heteroatom doping has been shown to enhance their optical properties and tune their fluorescence signature. Additionally, the incorporation of polymeric precursors in carbon dot synthesis has gained considerable interest with benefits to biological applications namely bioimaging, drug delivery and sensing, among others. In order to combine the desirable attributes of both, fluorescence enhancement and increased biocompatibility, polymers composed of high aromaticity and nitrogen content can be used as efficient carbon dot passivating agents. Here, the synthesis of fluorescent polymer-passivated carbon dots was developed through a microwave-assisted pyrolysis reaction of galactose, citric acid and polydopamine. Passivation of the dots with polydopamine induces a 90 nm red-shift in the fluorescence maxima from 420 to 510 nm. Moreover, passivation results in excitation-independent fluorescence and a 3.5-fold increase in fluorescence quantum yield, which increases from 1.3 to 4.6%. The application of the carbon dots as imaging probes was investigated in in vitro and in vivo model systems. Cytotoxicity studies in J774 and CHO-K1 cell lines revealed reduced cell toxicity for the polydopamine-passivated carbon dots in comparison to their unpassivated counterpart. In BALB/c mice, biodistribution studies demonstrated that regardless of surface passivation, the dots predominantly remained in the circulatory system 90 minutes post inoculation suggesting their potential use for cardiovascular therapies.

A novel CPC composite cement reinforced by dopamine coated SCPP fibers with improved physicochemical and biological properties

Traditional CPC cements have attracted wide attentions in repairing bone defects for injectability, easy plasticity and good osseointegration. However, its further application was limited by poor mechanical properties, long setting time and unsatisfactory biocompatibility. To solve these problems, polydopamine (DOPA) coated strontium-doped calcium polyphosphate (SCPP) fibers were added into CPC cements for the first time. A doping amount at fiber weight fraction of 0%, 1%, 2% and 5% was designed to develop a multifunctional composite fitting for bone tissues' regeneration and reconstruction and the optimum amount was selected through subsequent physicochemical and biological characterizations. The results implied DOPA coating successfully formed stable connections between SCPP fibers and CPC matrix, which simultaneously reinforced biomechanical strength and tenacity (5% SCPP/D/CPC samples exhibited more prominent mechanical property than others). In addition, 5% D/SCPP fibers doped composite cements were characterized as markedly-improved cytocompatibility: Sr²⁺ introduction induced cytoactive and significantly accelerated proliferation, attachment and spreading of osteoblasts. Besides, it also stimulated the secretion of OT, Col-I and ALP from seeded MG63, which was a critical character for further inducing osteogenic process, mineralization and bone tissues formation. The promoted cytocompatibility and improved osteogenesis-related growth factors' secretion could be attributed to constant and controllable release of Sr²⁺ and this deduction was approved by ICP analysis. In addition, Sr doping made this novel cement had a potential efficacy to inhibit aseptic loosening. In a word, present studies all demonstrated 5% SCPP/D/CPC composites could be a potential candidate material employed in bone regeneration and reconstruction for excellent mechanical property and cytocompatibility.

Enhanced osteoinductivity and corrosion resistance of dopamine/gelatin/rhBMP-2-coated β-TCP/Mg-Zn orthopedic implants: An in vitro and in vivo study

Magnesium-based biomaterials are attracting increasingly more attention for orthopedic applications based on their appropriate mechanical properties, biodegradability, and favorable biocompatibility. However, the high corrosion rate of these materials remains to be addressed. In this study, porous β-Ca3(PO4)2/Mg-Zn (β-TCP/Mg-Zn) composites were fabricated via a powder metallurgy method. The β-TCP/Mg-Zn composites with 6% porosity exhibited optimal mechanical properties, and thus, they were selected for surface modification. A novel dopamine/gelatin/recombinant human bone morphogenetic protein-2 (rhBMP-2) coating with demonstrated stability was prepared to further improve the corrosion resistance of the composite and enhance early osteoinductivity. The homogeneously coated β-TCP/Mg-Zn composite showed significantly improved corrosion resistance according to electrochemical and immersion tests. In addition, extracts from the dopamine/gelatin/rhBMP-2-coated β-TCP/Mg-Zn composite not only facilitated cell proliferation but also significantly enhanced the osteogenic differentiation of Sprague-Dawley rat bone marrow-derived mesenchymal stem cells in vitro. Furthermore, in vivo experiments were performed to evaluate the biodegradation, histocompatibility, and osteoinductive potential of the coated composite. No obvious pathological changes in the vital visceral organs were observed after implantation, and radiography and hematoxylin-eosin staining showed strong promotion of new bone formation, matched composite degradation and bone regeneration rates, and complete absorption of the released hydrogen gas. Collectively, these results indicate that the dopamine/gelatin/rhBMP-2-coated β-TCP/Mg-Zn composite offers improved corrosion resistance, favorable biocompatibility, and enhanced osteoinductive potential for use in the fabrication of orthopedic implants.

Green dual-template synthesis of AgPd core-shell nanoparticles with enhanced electrocatalytic activity

A key challenge in developing an ethanol oxidation reaction is nontoxic fabrication of highly active stable and low-cost catalysts. Here we design a green synthetic strategy of AgPd bimetallic nanosphere by a dual-template cascade method. The Pd nanoshell is firstly prepared using Vapreotide acetate as a primary template, and then the Ag nanoshell acts as a secondary template for the distribution of AgPd alloy nanoparticles. The AgPd nanoparticles have core-shell structures and various sizes, and their shell thicknesses are tuned by controlling the amount of PdCl₂. The six different samples are prepared, named AgPd-1, AgPd-2, AgPd-3, AgPd-4, AgPd-5, and AgPd-6, respectively. The mass current density of AgPd-5, is higher 3.87 times that of commercial Pd/C, and exhibits the best ethanol oxidation reaction activity and long-term stability. The main reasons are that the AgPd-5 possessed excellent specific surface area due to their rough structure, and Ag can remove more CO-like species. This is the first time a Vapreotide acetate/Ag-template method has been used to synthesize a AgPd core-shell structure, which would have broad application prospects for direct ethanol fuel cells.

Immobilization of Antimicrobial Silver and Antioxidant Flavonoid as a Coating for Wound Dressing Materials

Purpose

The aim of this study is to develop a new coating for wound dressings that is comprised of antimicrobial silver (Ag) and antioxidant flavonoid quercetin (Q).

Methods

Dip-coating was used to apply the coating on cotton gauge as a model dressing. Ag was immobilised using polydopamine as a priming and catalytic layer followed by coating of quercetin that was incorporated in a functionalized polydimethylsiloxane. The coating was investigated using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and release assay. The antimicrobial activity of quercetin and Ag was tested against Staphylococcus aureus (S. aureus). A surgical wound model on mice was used to evaluate the effects of the coated dressing on wound healing rates and tissue histology.

Results

Ag and quercetin showed enhanced antimicrobial activity against S. aureus when used in combination. Ag and quercetin were successfully immobilized onto the fibre of the dressing using the dip-coating process. The coating released Ag and quercetin over 8 days and showed strong antioxidant activity. In the wound healing model, complete wound closure was achieved in 12 days in the group receiving coated dressing and was associated with an enhancement in tissue remodelling and neo-angiogenesis and the reduction in tissue inflammation.

Conclusion

These new antimicrobial-antioxidant coatings may be promising in the development of advanced wound care therapies.

Development, Validation, and Performance of Chitosan-Based Coatings Using Catechol Coupling

The use of long-lasting polymer coatings on biodevice surfaces has been investigated to improve material-tissue interaction, minimize adverse effects, and enhance their functionality. Natural polymers, especially chitosan, are of particular interest due to their excellent biological properties, such as biocompatibility, non-toxicity, and antimicrobial properties. One way to produce chitosan coating is by covalent grafting with catechol molecules such as dopamine, caffeic acid, and tannic acid, resulting in an attachment ten times stronger than that of simple physisorption. Caffeic acid presents an advantage over dopamine because it allows direct chitosan grafting, due to its terminal carboxylic acid group, without the need of a linking arm, as employed in the dopamine approach. In this study, the grafting of chitosan using caffeic acid, over surfaces or in solution, is compared with dopamine grafting using poly(ethylene glycol) as a linking arm. The following coating properties are observed; covering and homogeneity are assessed by X-ray photoelectron spectroscopy and atomic force microscopy analyses, hydrophilicity with contact angle measurements, stability with aging tests, anticorrosion behavior, and coating non-toxicity. Results show that grafting using caffeic acid/chitosan in solution over a metallic surface may be advantageous, compared to traditional dopamine coating.

Biofunctionalization of metallic implants by calcium phosphate coatings

Metallic materials have been extensively applied in clinical practice due to their unique mechanical properties and durability. Recent years have witnessed broad interests and advances on surface functionalization of metallic implants for high-performance biofunctions. Calcium phosphates (CaPs) are the major inorganic component of bone tissues, and thus owning inherent biocompatibility and osseointegration properties. As such, they have been widely used in clinical orthopedics and dentistry. The new emergence of surface functionalization on metallic implants with CaP coatings shows promise for a combination of mechanical properties from metals and various biofunctions from CaPs. This review provides a brief summary of state-of-art of surface biofunctionalization on implantable metals by CaP coatings. We first glance over different types of CaPs with their coating methods and in vitro and in vivo performances, and then give insight into the representative biofunctions, i.e. osteointegration, corrosion resistance and biodegradation control, and antibacterial property, provided by CaP coatings for metallic implant materials.

Immobilization-Enhanced Eradication of Bacterial Biofilms and in situ Antimicrobial Coating of Implant Material Surface - an in vitro Study

PURPOSE

The aim of this study was to investigate a new method of in situ biofilm treatment for infected prostheses that remove bacterial biofilm and prevent reinfection through the use of an immobilizing agent in combination with the actions of biofilm-lysing enzymes and bactericidal antimicrobials.

METHODS

We investigated the combination of self-immobilization chemistry of dopamine with a biofilm-lysing enzyme, α-amylase (Am), and an antimicrobial agent, silver nitrate (Ag), to treat model Staphylococcus aureus (S. aureus) biofilms formed on titanium. The efficacy of biofilm removal and bacterial treatment was analyzed by crystal violet, colony-forming unit assays, confocal laser scanning microscopy, and scanning electron microscopy (SEM). To confirm the in situ coating of the titanium surface with antimicrobial Ag as a strategy to prevent bacterial recolonization, SEM in secondary electron mode (SE), backscatter electron mode, (BSE) and energy-dispersive spectroscopy (EDX) were used. The antimicrobial activity of the coated surface was evaluated by optical density measurement and colony-forming unit assays.

RESULTS

Polydopamine (PDA)-assisted treatment showed approximately a 2 log reduction in recoverable CFU and a 15% increase in biofilm removal efficacy compared to treatments that had only Am or Ag. More importantly, PDA-assisted treatment was found to immobilize Ag on the surface after the treatment, rendering them resistant to bacterial recolonization.

CONCLUSION

Our in vitro findings suggested that this PDA-assisted treatment and the surface immobilization-enhanced treatment concept could be promising in the development of advanced treatment for implant retention surgery for an infected prosthesis.

Study of the Relationship Between Chlorhexidine-Grafted Amount and Biological Performances of Micro/Nanoporous Titanium Surfaces

Biomaterial-associated infection and lack of sufficient osseointegration contribute to a large proportion of implant failures. Therefore, antibacterial and osseointegration-accelerating properties are important in implant surface design. In this study, a micro/nanoporous titanium surface was prepared through alkaline and heat treatments, covalently conjugated with aminosilane. Then, varying amounts of chlorhexidine (CHX) were covalently grafted onto the aminosilane-modified surface via glutaraldehyde to obtain different CHX-grafted surfaces. These as-prepared surfaces were evaluated in terms of their surface chemical composition, surface topography, CHX grafting amount, antibacterial activity, and osteoblast compatibility. The results showed that the CHX grafting amount increased with increasing CHX concentrations, leading to better antibacterial activity. CHX (1 mg/mL) resulted in the best antibacterial surface, which still retained good osteoblast compatibility. Meanwhile, competitive bacterial-cell adhesion analysis demonstrated that this surface has great value for osteoblast adhesion at the implant-bone interface even in the presence of bacteria. This effortless, easily performed, and eco-friendly technique holds huge promise for clinical applications.

Studies on Cell Compatibility, Antibacterial Behavior, and Zeta Potential of Ag-Containing Polydopamine-Coated Bioactive Glass-Ceramic

Dopamine is a small molecule that mimics the adhesive component (L-DOPA) of marine mussels with a catecholamine structure. Dopamine can spontaneously polymerize to form polydopamine (PDA) in a mild basic environment. PDA binds, in principle, to all types of surfaces and offers a platform for post-modification of surfaces. In this work, a novel Ag-containing polydopamine coating has been developed for the functionalization of bioactive glass-ceramics. In order to study the interactions between the surface of uncoated and coated samples and the environment, we have measured the surface zeta potential. Results confirmed that PDA can interact with the substrate through different chemical groups. A strongly negative surface zeta potential was measured, which is desirable for biocompatibility. The dual function of the material, namely the capability to exhibit bioactive behavior while being antibacterial and not harmful to mammalian cells, was assessed. The biocompatibility of the samples with MG-63 (osteoblast-like) cells was determined, as well as the antibacterial behavior against Gram-positive Staphylococcus carnosus and Gram-negative Escherichia coli bacteria. During cell biology tests, uncoated and PDA-coated samples showed biocompatibility, while cell viability on Ag-containing PDA-coated samples was reduced. On the other hand, antibacterial tests confirmed the strong antimicrobial properties of Ag-containing PDA-coated samples, although tailoring of the silver release will be necessary to modulate the dual effect of PDA and silver.

Nitrodopamine vs dopamine as an intermediate layer for bone regeneration applications

The aim of this paper was to present a parallel investigation of the poly(dopamine) (DP) and nitrodopamine (NDP) structures deposited on titanium surface (Ti) and titanium oxide nanotubes (NT-TiO₂/Ti) and to highlight their advantages and drawbacks to serve as an intermediary layer for bone regeneration applications. This study outlines some hypotheses regarding the manner in which these compounds are able to form a stable film that could serve as bioadhesive. The paper is also a study of structuring and evolution of film architecture for two coatings, polydopamine and nitrodopamine in terms of surface structure, stability, wettability, morphology, adhesion and ability to protect the titanium surface. All investigations are based on the data provided by surface characterization techniques: SEM, RAMAN, XRD, XPS, wettability and flexural strength. The impact of polydopamine and nitrodopamine coatings on the biocompatibility of titanium nanotubes was investigated in vitro. Cell morphology, viability, proliferation and pre-osteoblast differentiation were examined in detail. It was highlighted that both DP and NDP functionalized TiO₂ nanotubes display good cell response in terms of cell spreading, formation of focal adhesions, cell viability and proliferation, suggesting their suitability for applications in bone regeneration field. However, NDP coated TiO₂ nanotubes demonstrated an enhanced osteogenic potential compared to DP coated substrates.

Micro-/Nano-Scales Direct Cell Behavior on Biomaterial Surfaces

Cells are the smallest living units of a human body's structure and function, and their behaviors should not be ignored in human physiological and pathological metabolic activities. Each cell has a different scale, and presents distinct responses to specific scales: Vascular endothelial cells may obtain a normal function when regulated by the 25 µm strips, but de-function if the scale is removed; stem cells can rapidly proliferate on the 30 nm scales nanotubes surface, but stop proliferating when the scale is changed to 100 nm. Therefore, micro and nano scales play a crucial role in directing cell behaviors on biomaterials surface. In recent years, a series of biomaterials surface with micro and/or nano scales, such as micro-patterns, nanotubes and nanoparticles, have been developed to control the target cell behavior, and further enhance the surface biocompatibility. This contribution will introduce the related research, and review the advances in the micro/nano scales for biomaterials surface functionalization.

Rapid mussel-inspired synthesis of PDA-Zn-Ag nanofilms on TiO2 nanotubes for optimizing the antibacterial activity and biocompatibility by doping polydopamine with zinc at a higher temperature

Mussel-inspired deposition of polydopamine (PDA) is a green chemical method that has been used to load silver nanoparticles on titanium oxide nanotubes (TiO₂ NTs) to kill bacteria. However, a long reaction time is required for both the polymerization of dopamine and the reaction between PDA and silver nitrate. In addition, the deposition of silver nanoparticles is difficult to control, which may increase the risk of cytotoxicity. In this study, a rapid polymerization of dopamine was achieved by performing the reaction in a water bath at 90 °C (PDA-H). Furthermore, the reduction of Ag⁺ ions was markedly accelerated by the PDA-Zn film that was formed on the surface of TiO₂ NTs from a solution of dopamine and zinc nitrate under the same heating conditions. The reaction between the PDA-Zn film and silver nitrate was dramatically reduced to 10 min, and the silver nanoparticles deposited on the PDA-Zn film were more uniform than those by PDA-H film. This PDA-Zn-Ag-TiO₂ NTs material exhibited good antibacterial activity, as evidenced by the inhibition zone. The WST-1 assay indicated that the PDA-Zn-Ag film possessed a lower cell cytotoxicity and better biocompatibility than other Ag containing PDA films.

Electrospun Silk Fibroin Nanofibrous Scaffolds with Two-Stage Hydroxyapatite Functionalization for Enhancing the Osteogenic Differentiation of Human Adipose-Derived Mesenchymal Stem Cells

The development of functional scaffolds with improved osteogenic potential is important for successful bone formation and mineralization in bone tissue engineering. In this study, we developed a functional electrospun silk fibroin (SF) nanofibrous scaffold functionalized with two-stage hydroxyapatite (HAp) particles, using mussel adhesive-inspired polydopamine (PDA) chemistry. HAp particles were first incorporated into SF scaffolds during the electrospinning process, and then immobilized onto the electrospun SF nanofibrous scaffolds containing HAp via PDA-mediated adhesive chemistry. We obtained two-stage HAp-functionalized SF nanofibrous scaffolds with improved mechanical properties and capable of providing a bone-specific physiological microenvironment. The developed scaffolds were tested for their ability to enhance the osteogenic differentiation of human adipose-derived mesenchymal stem cells (hADMSCs) in vitro and repair bone defect in vivo. To boost their ability for bone repair, we genetically modified hADMSCs with the transcriptional coactivator with PDZ-binding motif (TAZ) via polymer nanoparticle-mediated gene delivery. TAZ is a well-known transcriptional modulator that activates the osteogenic differentiation of mesenchymal stem cells (MSCs). Two-stage HAp-functionalized SF scaffolds significantly promoted the osteogenic differentiation of TAZ-transfected hADMSCs in vitro and enhanced mineralized bone formation in a critical-sized calvarial bone defect model. Our study shows the potential utility of SF scaffolds with nanofibrous structures and enriched inorganic components in bone tissue engineering.

An nMgO containing scaffold: Antibacterial activity, degradation properties and cell responses

Bone repair failure caused by implant-related infections is a common and troublesome problem. In this study, an antibacterial scaffold was developed via selective laser sintering with incorporating nano magnesium oxide (nMgO) to poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV). The results indicated the scaffold exerted high antibacterial activity. The antibacterial mechanism was that nMgO could cause oxidative damage and mechanical damage to bacteria through the production of reactive oxygen species (ROS) and direct contact action, respectively, which resulted in the damage of their structures and functions. Besides, nMgO significantly increased the compressive properties of the scaffold including strength and modulus, due to its excellent mechanical properties and uniform dispersion in the PHBV matrix. Moreover, the degradation tests indicated nMgO neutralized the acid degradation products of PHBV and benefited the degradation of the scaffold. The cell culture demonstrated that nMgO promoted the cellular adhesion and proliferation, as well as osteogenic differentiation. The present work may open the door to exploring nMgO as a promising antibacterial material for tissue engineering.

Fabrication of core–shell Ag@pDA@HAp nanoparticles with the ability for controlled release of Ag+and superior hemocompatibility

We report a convenient and effective method to prepare Ag-NPs and core–shell Ag@pDA@HAp-NPs.

Sulfonated chitosan and dopamine based coatings for metallic implants in contact with blood

Thrombosis and calcification constitute the main clinical problems when blood-interacting devices are implanted in the body. Coatings with thin polymer layers represent an acknowledged strategy to modulate interactions between the material surface and the blood environment. To ensure the implant success, at short-term the coating should limit platelets adhesion and delay the clot formation, and at long-term it should delay the calcification process. Sulfonated chitosan, if compared to native chitosan, shows the unique ability to reduce proteins adsorption, decrease thrombogenic properties and limit calcification. In this work, stainless steel surfaces, commonly used for cardiovascular applications, were coated with sulfonated chitosan, by using dopamine and PEG as anchors, and the effect of these grafted surfaces on platelet adhesion, clot formation as well as on calcification were investigated. Surface characterization techniques evidenced that the coating formation was successful, and the sulfonated chitosan grafted sample exhibited a higher roughness and hydrophilicity, if compared to native chitosan one. Moreover, sulfonated surface limited platelet activation and the process of clot formation, thus confirming its high biological performances in blood. Calcium deposits were also lower on the sulfonated chitosan sample compared to the chitosan one, thus showing that calcification was minimal in presence of sulfonate groups. In conclusion, this sulfonated-modified surface has potential to be as blood-interacting material.

Functional droplets that recognize, collect, and transport debris on surfaces

We describe polymer-stabilized droplets capable of recognizing and picking up nanoparticles from substrates in experiments designed for transporting hydroxyapatite nanoparticles that represent the principal elemental composition of bone. Our experiments, which are inspired by cells that carry out materials transport in vivo, used oil-in-water droplets that traverse a nanoparticle-coated substrate driven by an imposed fluid flow. Nanoparticle capture is realized by interaction of the particles with chemical functionality embedded within the polymeric stabilizing layer on the droplets. Nanoparticle uptake efficiency is controlled by solution conditions and the extent of functionality available for contact with the nanoparticles. Moreover, in an elementary demonstration of nanoparticle transportation, particles retrieved initially from the substrate were later deposited "downstream," illustrating a pickup and drop-off technique that represents a first step toward mimicking point-to-point transportation events conducted in living systems.

Silver Nanocoating Technology in the Prevention of Prosthetic Joint Infection

Prosthetic joint infection (PJI) is a feared complication of total joint arthroplasty associated with increased morbidity and mortality. There is a growing body of evidence that bacterial colonization and biofilm formation are critical pathogenic events in PJI. Thus, the choice of biomaterials for implanted prostheses and their surface modifications may significantly influence the development of PJI. Currently, silver nanoparticle (AgNP) technology is receiving much interest in the field of orthopaedics for its antimicrobial properties and a strong anti-biofilm potential. The great advantage of AgNP surface modification is a minimal release of active substances into the surrounding tissue and a long period of effectiveness. As a result, a controlled release of AgNPs could ensure antibacterial protection throughout the life of the implant. Moreover, the antibacterial effect of AgNPs may be strengthened in combination with conventional antibiotics and other antimicrobial agents. Here, our main attention is devoted to general guidelines for the design of antibacterial biomaterials protected by AgNPs, its benefits, side effects and future perspectives in PJI prevention.

Dual functional polylactide–hydroxyapatite nanocomposites for bone regeneration with nano-silver being loaded via reductive polydopamine

In bone tissue engineering, scaffolding materials with antibacterial function are required to avoid failure in treating infected bone defects, and poly(l-lactide) - hydroxyapatite nanocomposites containing silver nanoparticles are good choices for the purpose.

Chlorhexidine hexametaphosphate nanoparticles as a novel antimicrobial coating for dental implants

Dental implants are an increasingly popular solution to missing teeth. Implants are prone to colonisation by pathogenic oral bacteria which can lead to inflammation, destruction of bone and ultimately implant failure. The aim of this study was to investigate the use of chlorhexidine (CHX) hexametaphosphate (HMP) nanoparticles (NPs) with a total CHX concentration equivalent to 5 mM as a coating for dental implants. The CHX HMP NPs had mean diameter 49 nm and composition was confirmed showing presence of both chlorine and phosphorus. The NPs formed micrometer-sized aggregated surface deposits on commercially pure grade II titanium substrates following immersion-coating for 30 s. When CHX HMP NP-coated titanium specimens were immersed in deionised water, sustained release of soluble CHX was observed, both in the absence and presence of a salivary pellicle, for the duration of the study (99 days) without reaching a plateau. Control specimens exposed to a solution of aqueous 25 µM CHX (equivalent to the residual aqueous CHX present with the NPs) did not exhibit CHX release. CHX HMP NP-coated surfaces exhibited antimicrobial efficacy against oral primary colonising bacterium Streptococcus gordonii within 8 h. The antimicrobial efficacy was greater in the presence of an acquired pellicle which is postulated to be due to retention of soluble CHX by the pellicle.

Antibiotic-decorated titanium with enhanced antibacterial activity through adhesive polydopamine for dental/bone implant

Implant-associated infections, which are normally induced by microbial adhesion and subsequent biofilm formation, are a major cause of morbidity and mortality. Therefore, practical approaches to prevent implant-associated infections are in great demand. Inspired by adhesive proteins in mussels, here we have developed a novel antibiotic-decorated titanium (Ti) material with enhanced antibacterial activity. In this study, Ti substrate was coated by one-step pH-induced polymerization of dopamine followed by immobilization of the antibiotic cefotaxime sodium (CS) onto the polydopamine-coated Ti through catechol chemistry. Contact angle measurement and X-ray photoelectron spectroscopy confirmed the presence of CS grafted on the Ti surface. Our results demonstrated that the antibiotic-grafted Ti substrate showed good biocompatibility and well-behaved haemocompatibility. In addition, the antibiotic-grafted Ti could effectively prevent adhesion and proliferation of Escherichia coli (Gram-negative) and Streptococcus mutans (Gram-positive). Moreover, the inhibition of biofilm formation on the antibiotic-decorated Ti indicated that the grafted CS could maintain its long-term antibacterial activity. This modified Ti substrate with enhanced antibacterial activity holds great potential as implant material for applications in dental and bone graft substitutes.

Synthesis of polydopamine at the femtoliter scale and confined fabrication of Ag nanoparticles on surfaces

Polydopamine is synthesized in confined femtolitre sized droplets and used as green nanoreactors to fabricate Ag nanoparticles on surfaces.

Engineering three-dimensional structures using bio-inspired dopamine and strontium on titanium for biomedical application

Poly(dopamine) films facilitate the initial attachment and proliferation of cells. Cell differentiation is enhanced by the release of strontium from the coatings.