Equilibrium, kinetics and mechanism of Au3+, Pd2+ and Ag+ ions adsorption from aqueous solutions by graphene oxide functionalized persimmon tannin

Utilizing cost-effective pyrocarbon for highly efficient gold retrieval from e-waste leachate

Addressing burdens of electronic waste (E-waste) leachate while achieving sustainable and selective recovery of noble metals, such as gold, is highly demanded due to its limited supply and escalating prices. Here we demonstrate an environmentally-benign and practical approach for gold recovery from E-waste leachate using alginate-derived pyrocarbon sorbent. The sorbent demonstrates potent gold recovery performance compared to most previously reported advanced sorbents, showcasing high recovery capacity of 2829.7 mg g-1, high efficiency (>99.5%), remarkable selectivity (Kd ~ 3.1 × 108 mL g-1), and robust anti-interference capabilities within environmentally relevant contexts. The aromatic structures of pyrocarbon serve as crucial electrons sources, enabling a hydroxylation process that simultaneously generates electrons and phenolic hydroxyls for the reduction of gold ions. Our investigations further uncover a "stepwise" nucleation mechanism, in which gold ions are reduced as intermediate gold-chlorine clusters, facilitating rapid reduction process by lowering energy barriers from 1.08 to -21.84 eV. Technoeconomic analysis demonstrates its economic viability with an input-output ratio as high as 1370%. Our protocol obviates the necessity for organic reagents whilst obtaining 23.96 karats gold product from real-world central processing units (CPUs) leachates. This work introduces a green sorption technique for gold recovery, emphasizing its role in promoting a circular economy and environmental sustainability.

A new tannin-based adsorbent synthesized for rapid and selective recovery of palladium and gold: Optimization using central composite design

A tannin-based adsorbent was synthesized by pomegranate peel tannin powder modified with ethylenediamine (PT-ED) for the rapid and selective recovery of palladium and gold. To characterize PT-ED, field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS-Mapping), and Fourier transform infrared spectroscopy (FT-IR) were used. Central composite design (CCD) was used for optimization. The kinetic, isotherm, interference of coexisting metal ions, and thermodynamics were studied. The optimal conditions, including Au (III) concentration = 30 m g L - 1 , Pd (II) concentration = 30 m g L - 1 , adsorbent mass = 26 mg, pH = 2, and time = 26 min with the sorption percent more than 99 %, were anticipated for both metals using CCD. Freundlich model and pseudo-second-order expressed the isotherm and kinetic adsorption of the both metals. The inhomogeneity of the adsorbent surface and the multi-layer adsorption of gold and palladium ions on the PT-ED surface are depicted by the Freundlich model. The thermodynamic investigation showed that P d 2 + and A u 3 + ions adsorption via PT-ED was an endothermic, spontaneous, and feasible process. The maximum adsorption capacity of P d 2 + and A u 3 + ions on PT-ED was 261.189 m g g - 1 and 220.277 m g g - 1 , respectively. The probable adsorption mechanism of P d 2 + and A u 3 + ions can be ion exchange and chelation. PT-ED (26 mg) recovered gold and palladium rapidly from the co-existing metals in the printed circuit board (PCB) scrap, including Ca, Zn, Si, Cr, Pb, Ni, Cu, Ba, W, Co, Mn, and Mg with supreme selectivity toward gold and palladium. The results of this work suggest the use of PT-ED with high selectivity and efficiency to recover palladium and gold from secondary sources such as PCB scrap.

Tailoring hierarchical nanostructures of tannin acid/alginate beads for straightforward selective recovery of high-purity Au(0) from aqueous solution

The utilization of biomass materials with functional properties and rational porous structures holds significant potential for the recovery of precious metals from secondary resources, while facing challenges in achieving rapid reduction and high recovery rates of metallic Au(0). Herein, a novel concept of achieving high-purity Au(0) efficiently by tailoring tannin acid (TA) architecture and porous structure of TA-functionalized alginate beads (P-TOSA). Optimized by structural engineering, the hierarchically nanostructured P-TOSA beads demonstrate exceptional selectivity and recovery capacity (756.1 ± 2.7 mg/g at pH 5), while maintaining a recovery efficiency of over 99 % across a broad range of pH values (1.0-8.0) through the synergistic combination of chelation-based chemisorption and phenolic groups-based redox reaction. Notably, the TA-based nanostructure-boosted reduced Au(0) served as nucleation sites, facilitating elongation and migration of gold crystals across the vein network, thus forming a shell composed with 90.4 ± 0.4 % of element gold. UV radiation exposure could further generate a dynamic redox system and expedite Au (III) reduction to ultra-high purity Au(0) (93.3 ± 1.1 %) via abnormal grain growth mode. Therefore, this study presents a practical and straightforward approach utilizing biomass microbeads for recycling precious metals in metallic form without the use of toxic eluents or additional reductants.

Tannin complexation with metal ions and its implication on human health, environment and industry: An overview

Tannins, also known as plant polyphenols (PPs), are secondary metabolites widely existing in higher plants and are a kind of natural renewable resource with wide distribution, variety and quantity. Tannin has become an important class of fine chemicals due to the easily modified molecular structure and the properties of antibacterial and antioxidant, combining with protein and complexing with metal ion. Besides being used for tanning leather, tannins are also widely used in wood adhesive, concrete water-reducing agents, oil drilling fluid viscosity-reducing agents, pharmaceutical, mineral processing, water treatment, gas desulfurization, metal anticorrosion, wood anticorrosion, printing and dyeing, liquor clarification, oil antioxidant, daily chemical products and other products preparation. There are two groups of tannins: condensed tannins (CTs) (flavonoid-derived proanthocyanidins) and hydrolysable tannins (HTs) (gallic acid ester-derived). Tannins can form complexes with metals through the ortho-dihydroxyphenolic group(s), especially with transition metals. The structure-activity relationships, stoichiometry, and origin of the insolubility of which were emphasized. Furthermore, this paper proposed an in-depth discussion of the associations of tannins-metal complexes in human health, environment and industries.

Enhancing electrochemical sensing through the use of functionalized graphene composites as nanozymes

Graphene-based nanozymes possess inherent nanomaterial properties that offer not only a simple substitute for enzymes but also a versatile platform capable of bonding with complex biochemical environments. The current review discusses the replacement of enzymes in developing biosensors with nanozymes. Functionalization of graphene-based materials with various nanoparticles can enhance their nanozymatic properties. Graphene oxide functionalization has been shown to yield graphene-based nanozymes that closely mimic several natural enzymes. This review provides an overview of the classification, current state-of-the-art development, synthesis routes, and types of functionalized graphene-based nanozymes for the design of electrochemical sensors. Furthermore, it includes a summary of the application of functionalized graphene-based nanozymes for constructing electrochemical sensors for pollutants, drugs, and various water and food samples. Challenges related to nanozymes as electrocatalytic materials are discussed, along with potential solutions and approaches for addressing these shortcomings.

Selective Adsorption and Recovery of Silver from Acidic Solution Using Biomass-Derived Sulfur-Doped Porous Carbon

It is vital to recycle precious metals effectively such as silver from waste sources because of limited natural reserves. Herein, passion fruit (Passiflora edulis Sims) shell-derived S-doped porous carbons (SPCs) were newly synthesized by hydrothermal carbonization and following with activation by KOH/(NH4)2SO4, and the adsorption of Ag+ on SPC under acidic solutions was investigated. It was found that the activator of (NH4)2SO4 can not only introduce the doping of S elements but also increase the proportion of mesopores in the as-prepared SPC. As the active site, the increasing S doping can improve the adsorption of Ag+ on SPC. The kinetic data of Ag+ adsorption by SPC was consistent with the pseudo-second-order kinetic model. The Langmuir isothermal model was used to well fit the Ag+ adsorption isotherms of SPC, and the maximum adsorption capacity of the optimized SPC-3 for Ag+ is up to 115 mg/g in 0.5 mol/L HNO3 solution. SPC-3 showed good selectivity toward Ag+ over diverse competing cations, which is mainly attributed to the strong bonding between Ag+ ions and the sulfur-containing functional groups on the surface of SPC-3 resulting in the formation of Ag2S nanoparticles. The adsorbed Ag could be recovered as an elemental form by a simple calcination. This study provides a new insight into the design of an environmentally friendly and efficient adsorbent for the selective recovery of silver from acidic aqueous media.

Colorimetric determination and recycling of gold(III) ions using label-free plasmonic H0.3MoO3 nanoparticles

A low-cost and environment-friendly sensor was developed for visual determination of gold ions (Au³⁺) by using label-free hydrogen doped molybdenum oxide (H_0.3MoO₃) nanoparticles as ratio probes. According to the characterization results of transmission electron microscopy, scanning electron microscopy, X-ray powder diffraction, and Fourier transform infrared spectra, Au³⁺ is easily reduced to red Au nanoparticles (AuNPs) by blue H_0.3MoO₃ nanoparticles. The color change of the solution depends on the concentration of Au³⁺, which makes it possible to detect Au³⁺ visually. Under optimal experimental conditions of pH 4.6, H_0.3MoO₃ nanoparticles concentration of 0.075 mg·mL^-1, and reaction time of 7 min, the sensor offers a satisfactory determination range from 0.5 to 70 μM and a good determination limit of 0.45 μM for Au³⁺. The concentration of Au³⁺ as low as 10 μM can be directly distinguished through the naked eye. Additionally, the colorimetric probe has also been proved applicable in environmental water samples. More importantly, the resulting AuNPs have good stability and oxidase-like activity, which may be directly used in sensing, catalysis, energy, and other fields.

Activity and potential mechanisms of action of persimmon tannins according to their structures: A review

One distinguishing feature of the persimmon, that differentiates it from other fruits, is its high proanthocyanidins content, known as persimmon tannin (PT). Despite the poor absorption of PT in the small intestine, results from animal studies demonstrate that PT has many health benefits. Our goal in this review is to summarize the literature that elucidates the relationship between PT structure and activity. In addition, we also summarize the potential mechanisms underlying the health benefits that result from PT consumption; this includes the hypolipidemic, hypoglycemic, antioxidant, anti-inflammatory, antiradiation, antibacterial and antiviral, detoxification effects on snake venom, and the absorption of heavy metals and dyes. Studies show that PT is a structurally distinct proanthocyanidins that exhibits a high degree of polymerization. It is galloylation-rich and possesses unique A-type interflavan linkages in addition to the more common B-type interflavan bonds. Thus, PT is converted into oligomeric proanthocyanidins by depolymerization strategies, including the nucleophilic substitution reaction, acid hydrolysis, and hydrogenolysis. In addition, multiple health benefits exerted by PT mainly involve the inactivation of lipogenic and intracellular inflammatory signaling pathways, activation of the fatty acid oxidation signaling pathway, regulation of gut microbiota, and highly absorptive properties.

An Efficient Electrochemical Biosensor to Determine 1,5-Anhydroglucitol with Persimmon-Tannin-Reduced Graphene Oxide-PtPd Nanocomposites

1,5-Anhydroglucitol (1,5-AG) is a sensitive biomarker for real-time detection of diabetes mellitus. In this study, an electrochemical biosensor to specifically detect 1,5-AG levels based on persimmon-tannin-reduced graphene oxide-PtPd nanocomposites (PT-rGO-PtPd NCs), which were modified onto the surface of a screen-printed carbon electrode (SPCE), was designed. The PT-rGO-PtPd NCs were prepared by using PT as the film-forming material and ascorbic acid as the reducing agent. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), ultraviolet-visible spectroscopy (UV-vis), and X-ray diffraction (XRD) spectroscopy analysis were used to characterise the newly synthesised materials. PT-rGO-PtPd NCs present a synergistic effect not only to increase the active surface area to bio-capture more targets, but also to exhibit electrocatalytic efficiency to catalyze the decomposition of hydrogen peroxide (H₂O₂). A sensitive layer is formed by pyranose oxidase (PROD) attached to the surface of PT-rGO-PtPd NC/SPCE. In the presence of 1,5-AG, PROD catalyzes the oxidization of 1,5-AG to generate 1,5-anhydrofuctose (1,5-AF) and H₂O₂ which can be decomposed into H₂O under the synergistic catalysis of PT-rGO-PtPd NCs. The redox reaction between PT and its oxidative product (quinones, PTox) can be enhanced simultaneously by PT-rGO-PtPd NCs, and the current signal was recorded by the differential pulse voltammetry (DPV) method. Under optimal conditions, our biosensor shows a wide range (0.1-2.0 mg/mL) for 1,5-AG detection with a detection limit of 30 μg/mL (S/N = 3). Moreover, our electrochemical biosensor exhibits acceptable applicability with recoveries from 99.80 to 106.80%. In summary, our study provides an electrochemical method for the determination of 1,5-AG with simple procedures, lower costs, good reproducibility, and acceptable stability.

Extraction of Gold Based on Ionic Liquid Immobilized in UiO-66: An Efficient and Reusable Way to Avoid IL Loss Caused by Ion Exchange in Solvent Extraction

Ionic liquids (ILs) have received considerable attention as a promising green solvent for extracting metal ions from aqueous solutions. However, the recycling of ILs remains difficult and challenging because of the leaching of ILs, which is caused by the ion exchange extraction mechanism and hydrolysis of ILs in acidic aqueous conditions. In this study, a series of imidazolium-based ILs were confined in a metal-organic framework (MOF) material (UiO-66) to overcome the limitations when used in solvent extraction. The effect of the various anions and cations of the ILs on the adsorption ability of AuCl₄^- was studied, and 1-hexyl-3-methylimidazole tetrafluoroborate ([HMIm]⁺[BF₄]^-@UiO-66) was used for the construction of a stable composite. The adsorption properties and mechanism of [HMIm]⁺[BF₄]^-@UiO-66 for Au(III) adsorption were also studied. The concentrations of tetrafluoroborate ([BF₄]^-) in the aqueous phase after Au(III) adsorption by [HMIm]⁺[BF₄]^-@UiO-66 and liquid-liquid extraction by [HMIm]⁺[BF₄]^- IL were 0.122 mg/L and 18040 mg/L, respectively. The results reveal that Au(III) coordinated with the N-containing functional groups, while [BF₄]^- was effectively confined in UiO-66, instead of undergoing anion exchange in liquid-liquid extraction. Electrostatic interactions and the reduction of Au(III) to Au(0) were also important factors determining the adsorption ability of Au(III). [HMIm]⁺[BF₄]^-@UiO-66 could be easily regenerated and reused for three cycles without any significant drop in the adsorption capacity.

Fluorescent hydrogels based on oxidized carboxymethyl cellulose with excellent adsorption and sensing abilities for Ag. Int J Biol Macromol 2022;213:955-966. [PMID: 35690162 DOI: 10.1016/j.ijbiomac.2022.06.029]

Heavy metal contamination in water and soil are harmful and destructive to the environment, it has always been regarded as a big problem. Herein, we developed a self-healing fluorescent hydrogel based on oxidized carboxymethyl cellulose with excellent sensing and adsorption abilities for Ag⁺. The detection and adsorption effects of hydrogels on heavy metal ions were studied. It turned out that the fluorescent hydrogel has sensitive detection and high adsorption capacity for Ag⁺, the detection limit was 3.798 μM, and the maximum adsorption capacity was 407 mg/g. The adsorption isotherm fitted the Langmuir model well, and the pseudo-secondary model for adsorption kinetics fitted well. The hydrogel could heal itself without external stimulus, it could be easily regenerated 7 times without loss of adsorption performance. In short, the prepared hydrogel has capability of self-healing, detecting and adsorbing heavy metal ions at the same time, good mechanical strength, these all made it a promising long-life adsorbent and provided a new way for wastewater treatment.

Graphene-based nanomaterials in the electroplating industry: A suitable choice for heavy metal removal from wastewater

The presence of various heavy metal ions in the industrial waste waters has recently been a challenging issue for human health. Since heavy metals are highly soluble in the aquatic environments and they can be absorbed easily by living organisms, their removal is essential from the environmental point of view. Many studies have been devoted to investigating the environmental behaviour of graphene-based nanomaterials as sorbent agents to remove metals from wastewaters arising by galvanic industries. Among the graphene derivates, especially graphene oxide (GO), due to its abundant oxygen functional groups, high specific area and hydrophilicity, is a high-efficient adsorbent for the removal of heavy and precious metals in aquatic environment. This paper reviews the main graphene, GO, functionalized GO and their composites and its applications in the metals removal process. The influencing factors, adsorption capacities and reuse capability are highlighted for the most extensively used heavy metals, including copper, zinc, nickel, chromium, cobalt and precious metals (i.e., gold, silver, platinum, palladium, rhodium, and ruthenium) in the electroplating process.

A facile approach for tuning optical and surface properties of novel biobased Alginate/POTE handleable films via solvent vapor exposure

Novel biobased films consisting of alginate blends with poly (octanoic acid 2-thiophen-3-yl-ethyl ester) (POTE), a conducting polymer, were prepared by solution casting, and their optical, morphological, thermal, and surface properties were studied. Using UV-visible spectroscopy, atomic force microscopy (AFM), and scanning electron microscopy (SEM), the effects of tetrahydrofuran solvent vapors on the optical properties and surface morphology of biobased films with different POTE contents were studied. Results indicate that morphological rearrangements of POTE take place during the process of solvent exposure. Specifically, the solvent vapor induced the formation of POTE small crystalline domains, which allows envisioning the potential of tuning UV-visible absorbance and wettability behavior of biobased films. Finally, theoretical electronic calculations (specifically frontier molecular orbitals analysis) provided consistent evidence on POTE's preferential orientation and selectivity toward the THF-vapor medium.

Effects of Persimmon Tannin-Aloe vera Composite on Cytotoxic Activities, and Radioprotection Against X-rays Irradiated in Human Hepatoma and Hepatic Cells

A persimmon tannin-Aloe vera composite powder (PT-A) was investigated for its capacity to protect against ionizing radiation. Human hepatic cells (L02 cells) and human hepatoma cells (HepG2 cells) were pretreated with different concentrations of PT-A or the single compounds (PT or Aloe vera) and radiated with X-rays. After radiation and post-incubation for 12 h or 24 h, the cell viability, apoptosis, and reactive oxygen species (ROS) production were analyzed by Cell Counting Kit 8 (CCK-8), 2',7'-dichlorfluorescein diacetate (DCFH-DA) staining, and Hoechst 33258 staining/flow cytometry, respectively. CCK-8 results illustrated that the optimal radiation dose L02 cells was 8 Gy for L02 cells, and the cell activity was 71.72% (IC₅₀ = 412.1 μg/mL) after post-radiation incubation of 12 h. For HepG2 cells, the optimal radiation dose was 8 Gy, and the cell activity was 62.37% (IC₅₀ = 213.0 μg/mL). The cell apoptotic rate was the lowest at a PT-A concentration of 200 μg/mL in L02 cells (4.32%, P < 0.05), and at 100 μg/mL in HepG2 cells (9.80%, P < 0.05). ROS production induced by radiation could be effectively inhibited by 200 μg/mL of PT-A in L02 cells, and by 100 μg/mL of PT-A in HepG2 cells. The PT-A composite has good radioprotective effects on cell vitality and apoptosis of X-rays radiation exposure towards L02 cells and HepG2 cells compared to the persimmon tannin or Aloe vera. Therefore, PT-A composite might be useful as a natural, harmless anti-ionizing radiation agent, and has various clinical application prospects in future.

Persimmon tannin functionalized polyacrylonitrile fiber for highly efficient and selective recovery of Au(III) from aqueous solution

An efficient fibrous adsorbent (PANF-TETA-PT) was prepared via grafting triethylenetetramine (TETA) on polyacrylonitrile fiber (PANF), followed by persimmon tannin (PT) immobilizing. Detailed characterization certified that plenty amounts of amino and phenolic hydroxyl groups existed on the surface of PANF-TETA-PT, which would provide excellent active sites for Au(III) adsorption. The batch characteristic results found that the adsorption equilibrium data could be fitted well with Langmuir equation, while the obtained kinetic data were consistent with the Pseudo-second-order equation. The maximum equilibrium adsorption capacity of PANF-TETA-PT towards Au(III) (801.2 mg/g) was apparently superior than that of the reported adsorbents, and the competitive adsorption showed that PANF-TETA-PT had a good preference to adsorption Au(III) in spite of some coexisting pollutants. The characterization analysis of Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffractometer spectrum (XRD) revealed that the electrostatic attraction and chelation dominated the uptake of Au(III) on PANF-TETA-PT, in which a part of loaded Au(III) was reduced to Au particles with the help of reductive functional groups. Thus, this adsorbent could be as a promising candidate to separation and preconcentration of Au(III) from wastewater.

Development and characterization of chitosan functionalized dialdehyde viscose fiber for adsorption of Au(III) and Pd(II)

A highly efficient fiber-based adsorbent (DAVFs-CS) was developed via decoration of chitosan (CS) on the dialdehyde viscose fibers (DAVFs) substrate, and employed to selective separation of precious metals from simulated contaminated water. The surface functionalization of the solid material was probed using the Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), Thermogravimetric analysis (TGA) and nuclear magnetic resonance (NMR) technique. The batch characteristic results showed that the maximum uptake capacities of DAVFs-CS were higher up to 322 mg/g and 207 mg/g for Au(III) and Pd(II) at optimal pH 2.0 and 3.0, which exhibited competitiveness with the majority of the reported adsorbents. Meanwhile, the adsorption data were in accordance with Langmuir and PSO equations, which indicated that the monolayer chemisorption dominated the adsorption process. The competitive adsorption study showed that the removal efficiency of Au(III) was not susceptible to the co-existing impurities. Adsorption mechanism study revealed that the negative Au(III) or Pd(II) species were firstly adsorbed on DAVFs-CS via the protonated amino groups, subsequently the partially reduction of them to zero-valent gold and palladium with the help of reductive functional groups. Thus, DAVFs-CS could be as a promising adsorbent to recovery of precious metals owning to its unique adsorption mechanism and excellent adsorption performance.

Uptake and Recovery of Gold from Simulated Hydrometallurgical Liquors by Adsorption on Pine Bark Tannin Resin

The recovery of critical and precious metals from waste electrical and electronic equipment (WEEE) is an environmental and economic imperative. Biosorption has been considered a key technology for the selective extraction of gold from hydrometallurgical liquors obtained in the chemical leaching of e-waste. In this work, the potential of tannin resins prepared from Pinus pinaster bark to sequester and recover gold(III) from hydrochloric acid and aqua regia solutions was assessed. Equilibrium isotherms were experimentally determined and maximum adsorption capacities of 343 ± 38 and 270 ± 19 mg g−1 were found for Au uptake from HCl and HCl/HNO3 (3:1 v/v) solutions containing 1.0 mol L−1 H+. Higher levels of acidity (and chloride ligands) significantly impaired the adsorption of gold from both kinds of leaching solutions, especially in the aqua regia system, in which the adsorbent underperformed. Pseudo-first and pseudo-second order models successfully described the kinetic data. The adsorbent presented high selectivity towards gold. Actually, in simulated aqua regia WEEE liquors, Au(III) was extensively adsorbed, compared to Cu(II), Fe(III), Ni(II), Pd(II), and Zn(II). In three adsorption–desorption cycles, the adsorption capacity of the regenerated adsorbent moderately decreased (19%), although the gold elution in acidic thiourea solution had been quite limited. Future research is needed to examine more closely the elution of gold from the exhausted adsorbents. The results obtained in this work show good perspectives as regards the application of pine bark tannin resins for the selective extraction of Au from electronic waste leach liquors.

Protecting HaCaT cells from ionizing radiation using persimmon tannin-Aloe gel composite

Context: Persimmon tannin (extract of Diospyros kaki L.f [Ebenaceae]) and Aloe gel (extract of Aloe vera (L.) Burm.f. [Asphodelaceae]) are known as anti-radiation agents. However, radiation resistance of the persimmon tannin-Aloe gel composite remains inconclusive.Objective: To investigate the capacity of the persimmon tannin-Aloe gel composite to protect against ionising radiation at the cellular level.Materials and methods: HaCaT (human epidermal keratinocytes) cells were pre-treated with PT-A-1 (the mass ratio of persimmon tannin and Aloe gel was 2:1) or the single component (persimmon tannin or Aloe gel) at various concentrations (0, 50, 100, 200, 400, 800 μg/mL. Control group: medium with no HaCaT cells), and then radiated with X-rays (radiation dose: 4, 8, 12, 16, and 20 Gy). Cell viability, cell apoptosis, and radiation-induced intracellular reactive oxygen species (ROS) generation were analysed by CCK-8, Hoechst 33258 staining/flow cytometry, and 2',7'-dichlorfluorescein diacetate (DCFH-DA) assay, respectively, for 12 or 24 h incubation after radiation.Results: The optimal radiation dose and post-radiation incubation period were determined to be 8 Gy and 12 h. CCK-8 activity detection showed that the cell activity was 77.85% (p < 0.05, IC₅₀ = 55.67 μg/mL). The apoptotic rate was the lowest (4.32%) at 200 μg/mL of PT-A-1 towards HaCaT cells. ROS production was the most effectively suppressed by 200 μg/mL PT-A-1 towards HaCaT cells.Discussion and conclusions: The persimmon tannin-Aloe gel composite has good radioprotective effect, and which will facilitate its clinic application as a potential natural anti-radiation agent in future.

Tannin-Based Hybrid Materials and Their Applications: A Review

Tannins are eco-friendly, bio-sourced, natural, and highly reactive polyphenols. In the past decades, the understanding of their versatile properties has grown substantially alongside a continuously broadening of the tannins' application scope. In particular, recently, tannins have been increasingly investigated for their interaction with other species in order to obtain tannin-based hybrid systems that feature advanced and/or novel properties. Furthermore, in virtue of the tannins' chemistry and their high reactivity, they either physicochemically or physically interact with a wide variety of different compounds, including metals and ceramics, as well as a number of organic species. Such hybrid or hybrid-like systems allow the preparation of various advanced nanomaterials, featuring improved performances compared to the current ones. Consequently, these diverse-shaped materials have potential use in wastewater treatment or catalysis, as well as in some novel fields such as UV-shielding, functional food packaging, and biomedicine. Since these kinds of tannin-based hybrids represent an emerging field, thus far no comprehensive overview concerning their potential as functional chemical building blocks is available. Hence, this review aims to provide a structured summary of the current state of research regarding tannin-based hybrids, detailed findings on the chemical mechanisms as well as their fields of application.

Hierarchically flower-like WS2 microcrystals for capture and recovery of Au (III), Ag (I) and Pd (II)

In the past few years, two-dimensional (2D) nanomaterials have emerged great potential for the removal of valuable metals and the capture of polluted-heavy metals. Herein, hierarchically flower-like microcrystals with 2D WS₂ nanosheets (F-WS₂ MCs) were prepared by one-pot hydrothermal synthesis strategy and its adsorption performances for precious metals were systematically assessed. The excellent adsorption efficiencies of ∼86.8%, ∼27.6%, and ∼94.1% towards Ag (I), Pd (II), and Au (III) respectively were achieved within 120 min, and the adsorption curves were in good agreement with a pseudo-second-order kinetic model showing a fast uptake rate at the optimum pH values (1.30 for Au (III), 1.43 for Ag (I), and 3.20 for Pd (II)). The adsorption isotherm followed well in the Langmuir model with the maximum removal capacities (q_max) of 186.2 mg g^-1 for Ag (I), 67.29 mg g^-1 for Pd (II), and 1340.6 mg g^-1 for Au (III), respectively. Furthermore, for recycling purposes, the relevant desorption solution was investigated with different ratios of monobasic acid and thiourea, suggesting the best desorption efficiency of 93.03%, 88.08%, and 85.34% for Ag (I), Pd (II), and Au (III), respectively. By characterizing the crystalline phase, and micromorphology element mapping of F-WS₂ MCs before and after adsorption, the strong affinity and significant adsorption-reduction were indicated to dominate the adsorption process. Therefore, this work broadens the application range of WS₂ microcrystals, providing an alternative material for capturing precious metals and wastewater treatment applications.

One step forward: How can functionalization enhance the adsorptive properties of graphene towards metallic ions and dyes?

Functionalized graphene and its derivatives have been subject of many recent studies investigating their use as scavenger of various industrial pollutants. Adsorption is a feasible treatment, which can employ a wide variety of materials as adsorbents. Additionally, graphene has been distinguished for its remarkable properties, such as mechanical resistance, flexibility and electric conductivity. A relevant aspect of functionalized graphene is related to its selectivity, resulting in increased removal rates of specific pollutants. Hence, the functionalization process of graphene nanosheets is the cutting edge of the materials and environmental sciences, promoting the development of innovative and highly capable sorbents. The purpose of this review is to assemble the available information about functionalized graphene nanomaterials used for the removal of water pollutants and to explore its wide potential. In addition, various optimal experimental conditions (solution pH, equilibrium time, adsorbent dosage) are discussed. In each topic, aspects of environmental protection of adsorption process were evaluated, as well as the most recent works, available from high impact journals in the field, have been explored. Additionally, the employment of natural compounds to functionalize, reduce and support graphene, was evaluated as green alternatives to chemicals.

Adsorptive recovery of Au(III) from aqueous solution using crosslinked polyethyleneimine resins

Resin adsorption is considered as a promising method to recover gold ions from wastewater, but further reduction reaction is required to convert gold ions into particles. In this study, a crosslinked polyethyleneimine resin (CPEIR) was developed via a suspension polymerization of polyethyleneimine (PEI) and ethylene glycol diglycidyl ether (EGDE) for gold recovery. The Au(III) adsorption capacities of CPEIR were significantly impacted by solution pH and initial Au(III) concentrations but unaffected by co-existing metal ions. Compared with commercial anion-exchange resin IRA400, the CPEIR exhibited higher sorption amount and selectivity for Au(III) due to its high density of amine and hydroxyl groups on the surfaces. The adsorption isotherm of Au(III) on CPEIR was well described by the Langmuir equation, and the maximum uptake amount of Au(III) was high up to 943.5 mg/g, much higher than the reported sorbents. The adsorption kinetic data on the CPEIR were fitted well by the Pseudo-second-order equation, and the intraparticle diffusion was found to be the rate-controlling process of Au(III) adsorption. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analysis confirmed that Au(III) ions were adsorbed on the CPEIR via electrostatic attraction and chelating interaction, and subsequently the partial loaded Au(III) ions were reduced to elemental gold whereas the hydroxyl groups of CPEIR were oxidized to carbonyl groups.

Enhanced Heavy Metal Removal from Acid Mine Drainage Wastewater Using Double-Oxidized Multiwalled Carbon Nanotubes

Due to the unique properties of carbon nanotubes (CNTs), they have attracted great research attention as an emergent technology in many applications including water and wastewater treatment. However, raw CNTs have few functional groups, which limits their use in heavy metal removal. Nevertheless, their removal properties can be improved by oxidation processes that modify its surface. In this study, we assessed the capacity of oxidized and double-oxidized multiwalled carbon nanotubes (MWCNTs) to remove heavy metals ions from acidic solutions. The MWCNTs were tested for copper (Cu), manganese (Mn), and zinc (Zn) removal, which showed an increment of 79%, 78%, and 48%, respectively, with double-oxidized MWCNTs compared to oxidized MWCNTs. Moreover, the increase in pH improved the sorption capacity for all the tested metals, which indicates that the sorption potential is strongly dependent on the pH. The kinetic adsorption process for three metals can be described well with a pseudo-second-order kinetic model. Additionally, in multimetallic waters, the sorption capacity decreases due to the competition between metals, and it was more evident in the removal of Zn, while Cu was less affected. Besides, XPS analysis showed an increase in oxygen-containing groups on the MWCNTs surface after oxidation. Finally, these analyses showed that the chemical interactions between heavy metals and oxygen-containing groups are the main removal mechanism. Overall, these results contribute to a better understanding of the potential use of CNTs for water treatment.

Fabrication and investigation of gold (III) ion-imprinted functionalized silica particles

Au (III) ion-imprinted mesoporous silica particles (Au-Si-Py) was manufactured by the condensation reaction of (3-Aminopropyl)triethoxysilane (AT)and 2-pyridinecarboxaldehyde (Py). The obtained AT-Py Schiff base ligand was then coordinate with the template gold ions and the polymerizable gold-complex was allowed to gel in presence of tetraethoxysilane (TEOS) and then the coordinated gold ions were leached out of the obtained silica matrix using acidified thiourea solution. During the synthetic steps, the obtained materials were investigated utilizing advanced instrumental and spectral methods. Moreover, the morphological structure of both Au (III) ions imprinted Au-Si-Py and non-imprinted NI-Si-Py silica particles were visualized using scanning electron microscope (SEM). Various adsorption experiments had been carried out using both Au-Si-Py and NI-Si-Py to examine their potential for selective extraction of gold ions under different conditions.

Three-dimensional porous graphene oxide-maize amylopectin composites with controllable pore-sizes and good adsorption-desorption properties: Facile fabrication and reutilization, and the adsorption mechanism

Three-dimensional (3D) porous graphene oxide-maize amylopectin (GO-MA) composites with controllable pore-sizes composites in the range of 6-40 nm were prepared by facile hydrothermal-assisted assembly approaches. The morphologies, pore sizes, specific surface area (SSA) and compositions of GO-MA_x:y composites with and different GO-to-MA mass ratios (x:y) were characterized by scanning electron microscopy (SEM), N₂ adsorption-desorption isotherms, Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). To reveal the adsorption-desorption mechanism, effects of contact time, temperature, initial adsorbate concentration, pH value of the solution on the adsorption process were studied in detail. The adsorption capacities of 3D GO-MA_20:1 composite for organic contaminants including tert-butyl hydroquinone (TBHQ), p-aminophenol (PAP), p-nitrophenol (PNP), o-nitrophenol (MNP), hydroquinone (HQ), alizarin red S (ARS) and neutral red (NR) were 22.17, 116.4, 44.78, 36.96, 16.10, 39.92 and 24.23 mg g^-1, respectively. The adsorption capacities of GO-MA_30:1 composite for inorganic substances including Pb²⁺, Mn²⁺, Cr₂O₇^2-, Cd²⁺, Cu²⁺, Nd³⁺, La³⁺, Y³⁺, Yb³⁺ and Er³⁺ were 84.76, 7.92, 13.6, 17.64, 30.56, 25.52, 12.48, 16.96, 23.32 and 30.32 mg g^-1, respectively. In addition, GO-MA_x:y composites also exhibited high mechanical properties and good reusability. Consequently, GO-MA_x:y composites could be used as reusable adsorbents for removal/enrichment inorganic/organic substances in aqueous solutions.

Non-enzymatic electrochemical hydrogen peroxide biosensor based on reduction graphene oxide-persimmon tannin‑platinum nanocomposite

Hydrogen peroxide (H₂O₂) is one of the most universal and essential ingredients in distinct biological tissues. Herein, a novel non-enzymatic sensor based on reduction graphene oxide-persimmon tannin‑platinum nanocomposite (RGO-PT-Pt) was exploited for H₂O₂ detection. RGO-PT-Pt nanocomposite was prepared by reduction procedure with ascorbic acid as reducing agent and characterized by Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), ultraviolet visible spectroscopy (UV-vis) and Fourier infrared spectroscopy (FT-IR). Taking advantage of high electro-catalytic efficiency of Pt nanoparticles, high electronic conductivity and large surface area of RGO, and significant adsorption ability of PT on metal ions and its prevention of agglomeration to promote RGO dispersion, RGO-PT-Pt nanocomposite revealed better catalytic ability towards H₂O₂ via a synergistic effect. Under the optimal conditions, the RGO-PT-Pt non-enzymatic biosensor exhibited outstanding electrocatalytic activity towards H₂O₂ reduction. The amperometric response demonstrated a linear relationship with H₂O₂ concentration from 1.0 to100 μM with the correlation coefficient of 0.9931. The limit of detection was 0.26 μM (S/N = 3) and the response time was 3 s. Furthermore, the fabricated sensor exhibited a practical applicability in the quantification of H₂O₂ in human serum samples with an excellent recovery rate. Due to excellent performance such as fast response time, low detection limit, high stability and selectivity, the RGO-PT-Pt non-enzymatic biosensor has potential application in clinical diagnostics.

Effects of dispersible MoS2 nanosheets and Nano-silver coexistence on the metabolome of yeast

As a new rising star in the post-graphene two-dimensional materials (2DMs), molybdenum disulfide (MoS₂) attracts increasing attentions and is widely applied. However, the chemical and toxicological interaction between MoS₂ and other co-contaminants is still poorly understood. Nano-silver (N-Ag) is the most commonly used nanomaterial in commercial products and distributed widely in the environment. Herein, we investigated the effects of chitosan functionalized MoS₂ (CS-MoS₂) nanosheets, a water-dispersible form of MoS₂, on the microbial toxicity of N-Ag. We found that the incorporation of CS-MoS₂ nanosheets attenuated the oxidative stress induced by N-Ag on yeast cells, while caused more membrane stress. In addition, the inhibition of N-Ag on the metabolic activities of yeast cells could be attenuated by CS-MoS₂ nanosheets as well. The coexistence of N-Ag and CS-MoS₂ nanosheets mainly perturbed the amino acid-related metabolic pathways in yeast cells, and phosphoric acid was a potential nanotoxicity biomarker. We further found that CS-MoS₂ nanosheets dramatically absorbed the Ag ion released from N-Ag, which might be responsible for its attenuation effect on the microbial toxicity of N-Ag. Our findings provide more new insights for the ecotoxicity evaluation of MoS₂ and other 2DMs.

Facile Synthesis, Characterization of Poly-2-mercapto-1,3,4-thiadiazole Nanoparticles for Rapid Removal of Mercury and Silver Ions from Aqueous Solutions

Industrial pollution by heavy metal ions such as Hg2+ and Ag⁺ is a universal problem owing to the toxicity of heavy metals. In this study, a novel nano-adsorbent, i.e., poly-2-mercapto-1,3,4-thiadiazole (PTT), was synthesized and used to selectively adsorb mercury and silver ions from aqueous solutions. PTT nanoparticles were synthesized via chemical oxidative dehydrogenation polymerization under mild conditions. Oxidant species, medium, monomer concentration, oxidant/monomer molar ratio, and polymerization temperature were optimized to obtain optimum yields. The molecular structure and morphology of the nanoparticles were analyzed by ultraviolet-visible (UV-Vis), Fourier transform infrared (FT-IR), matrix-assisted laser desorption/ionization/time-of-flight (MALDI/TOF) mass and X-ray photoelectron (XPS) spectroscopies, wide-angle X-ray diffraction (WAXD), theoretical calculations and transmission electron microscopy (TEM), respectively. It was found that the polymerization of 2-mercapto-1,3,4-thiodiazole occurs through head-to-tail coupling between the S(2) and C(5) positions. The PTT nanoparticles having a peculiar synergic combination of four kinds of active groups, S⁻, ⁻SH, N⁻N, and =N⁻ with a small particle size of 30⁻200 nm exhibit ultrarapid initial adsorption rates of 1500 mg(Hg)·g-1·h-1 and 5364 mg(Ag)·g-1·h-1 and high adsorption capacities of up to 186.9 mg(Hg)·g-1 and 193.1 mg(Ag)·g-1, becoming ultrafast chelate nanosorbents with high adsorption capacities. Kinetic study indicates that the adsorption of Hg2+ and Ag⁺ follows the pseudo-second-order model, suggesting a chemical adsorption as the rate-limiting step during the adsorption process. The Hg2+ and Ag⁺-loaded PTT nanoparticles could be effectively regenerated with 0.1 mol·L-1 EDTA or 1 mol·L-1 HNO₃ without significantly losing their adsorption capacities even after five adsorption⁻desorption cycles. With these impressive properties, PTT nanoparticles are very promising materials in the fields of water-treatment and precious metals recovery.