Effect of linking arm hydrophilic/hydrophobic nature, length and end-group on the conformation and the RGD accessibility of surface-immobilized fibronectin

The Cell Adhesion and Proliferation Enhancement Impact of Low-Temperature Atmospheric Pressure Plasma-Polymerized Heptylamine on the Surface of Ti6Al4V Alloy

To chemically functionalize the Ti6Al4V alloy surface, a custom-made low-temperature atmospheric pressure plasma reactor device was used to polymerize heptylamine on it. The effect of different deposition times, an important process parameter, was also investigated. For each deposition time group, the surface morphology was observed via scanning electron microscopy (SEM). The surface chemical content was analyzed via X-ray photoelectron spectroscopy, and surface hydrophilicity was measured via water contact angle. The adhesion of bone marrow stromal cells (BMSCs) on the modified Ti6Al4V alloy surfaces was also observed via SEM. A quantitative evaluation of cell proliferation was performed via the Cell Counting Kit-8 assay. The results revealed that amino groups were introduced on the Ti6Al4V alloy surface via plasma-polymerized heptylamine (PPHA). The percentages of NH2/C for various deposition times (0 s, 30 s, 45 s, 60 s, 90 s, and 120 s) were 3.39%, 5.14%, 6.71%, 6.72%, 7.31%, and 7.65%. A 30 s, 45 s, and 60 s deposition time could significantly increase surface hydrophilicity with a mean water contact angle of 62.1 ± 1.6°, 65.7 ± 1.1°, and 88.2 ± 1.4°, respectively. Meanwhile, a 60 s, 90 s, and 120 s deposition time promoted BMSCs cell adhesion and proliferation. However, this promotion effect differed non-significantly among the three groups. In conclusion, the introduction of amino groups on the Ti6Al4V alloy surface exhibited surface modification and enhancement of cell adhesion and proliferation, which was partially associated with deposition time.

Dual-Functional Polyetheretherketone Surface with an Enhanced Osteogenic Capability and an Antibacterial Adhesion Property In Vitro by Chitosan Modification

A chitosan layer was covalently bonded to a polyetheretherketone (PEEK) surface using a simple facile self-assembly method to address inadequate biological activity and infection around the implant. The surface characterization, layer degradation, biological activity, and antibacterial adhesion properties of chitosan-modified PEEK (PEEK-CS) were studied. Through chitosan grafting, the surface morphology changed, the surface roughness increased, and the contact angle decreased significantly. PEEK-CS boosted cell adhesion, proliferation, increased alkaline phosphate activity, extracellular matrix mineralization, and expression of osteogenic genes. PEEK-CS demonstrated less adhesion to Porphyromonas gingivalis as well as less bacterial adhesion to P. gingivalis and Streptococcus mutans. According to our findings, chitosan modification significantly improved the osteogenic ability and antibacterial adhesion of PEEK in vitro.

Fibronectin-Enriched Biomaterials, Biofunctionalization, and Proactivity: A Review

Modern innovation in reconstructive medicine implies the proposition of material-based strategies suitable for tissue repair and regeneration. The development of such systems necessitates the design of advanced materials and the control of their interactions with their surrounding cellular and molecular microenvironments. Biomaterials must actively engage cellular matter to direct and modulate biological responses at implant sites and beyond. Indeed, it is essential that a true dialogue exists between the implanted device and the cells. Biomaterial engineering implies the knowledge and control of cell fate considering the globality of the adhesion process, from initial cell attachment to differentiation. The extracellular matrix (ECM) represents a complex microenvironment able to meet these essential needs to establish a relationship between the material and the contacting cells. The ECM exhibits specific physical, chemical, and biochemical characteristics. Considering the complexity, heterogeneity, and versatility of ECM actors, fibronectin (Fn) has emerged among the ECM protagonists as the most pertinent representative key actor. The following review focuses on and synthesizes the research supporting the potential to use Fn in biomaterial functionalization to mimic the ECM and enhance cell–material interactions.

Fibronectin grafting to enhance skin sealing around transcutaneous titanium implant

Intraosseous transcutaneous amputation prosthesis is a new approach in orthopedic implants that overcomes socket prosthesis problems. Its long-term performance requires a tight skin-implant seal to prevent infections. In this study, fibronectin (Fn), a widely used adhesion protein, was adsorbed or grafted onto titanium alloy. Fn grafting was performed using two different linking arms, dopamine/glutaric anhydride or phosphonate. The characterization of Fn-modified surfaces showed that Fn grating via phosphonate has led to the highest amount of Fn cell-binding site (RGD, arginine, glycine, and aspartate) available on the surface. Interestingly, cell culture studies revealed a strong correlation between the amount of available RGD ligands and cellular behavior, since enhanced proliferation and spreading of fibroblasts were noticed on Fn-grafted surfaces via phosphonate. In addition, an original in vitro mechanical test, inspired from the real situation, to better predict clinical outcomes after implant insertion, has been developed. Tensile test data showed that the adhesion strength of a bio-engineered dermal tissue was significantly higher around Fn-grafted surfaces via phosphonate, as compared to untreated surfaces. This study sheds light on the importance of an appropriate selection of the linking arm to tightly control the spatial conformation of biomolecules on the material surface, and consequently cell interactions at the interface tissue/implant.

EMI Shielding of the Hydrophobic, Flexible, Lightweight Carbonless Nano-Plate Composites

The cost-effective spray coated composite was successfully synthesis and characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, and X-ray diffraction techniques. The one step synthetic strategy was used for the synthesis of nanoplates that have a crystalline nature. The composites are amorphous and hydrophobic with micron thickness (<400 m). The maximum contact angle showed by composite is 132.65° and have wetting energy of -49.32 mN m-1, spreading coefficient -122.12 mN m-1, and work of adhesion 23.48 mN m-1. The minimum thickness of synthesized nanoplate is 3 nm while the maximum sheet resistance, resistivity, and electrical conductivity of the composites are 11.890 ohm sq-1, 0.4399 Ω.cm-1, and 8.967 S.cm-1, respectively. The cobalt nanoplate coated non-woven carbon fabric (CoFC) possesses excellent sheet resistance, hydrophobic nature, and EMI shielding efficiency of 99.99964%. The composite can block above 99.9913% of incident radiation (X band). Hence, the composite can be utilized in application areas such as medical clothes, mobile phones, automobiles, aerospace, and military equipment.