Alumina-silica nano-sorbent from plant fly ash and scrap aluminium foil in removing nickel through adsorption

The efficient uptake of uranium by amine-functionalized β-cyclodextrin supported fly ash composite from polluted water

A novel polyethyleneimine/polydopamine-functionalized β-cyclodextrin supported fly ash adsorbent (PEI/PDA/β-CD/FA) had been synthesized to uptake uranium from polluted water. At pH = 5.0 and T = 298 K, the uranium uptake efficiency and capacity of PEI/PDA/β-CD/FA reached to 98.7 % and 622.8 mg/g, respectively, which were much higher than those of FA (71.4 % and 206.7 mg/g).The excellent uranium uptake properties of PEI/PDA/β-CD/FA could be explained by three points: (1) using β-CD as a supporting material could effectively avoid the aggregation of FA and improve the hydrophily of FA; (2) the unique cavity structure of β-CD could form chelates with uranyl ions; (3) the formation of PEI/PDA co-deposition coating on FA further enhanced the affinity of FA to UO22+. With the presence of interfering ions, the uptake efficiency of PEI/PDA/β-CD/FA for uranium was still up to 94.5 % after five cycles, indicating the high selectively and recoverability of PEI/PDA/β-CD/FA. In terms of the results of characterizations, uranium was captured by PEI/PDA/β-CD/FA via electrostatic attraction, hydrogen bond, coordination and complexation. To sum up, PEI/PDA/β-CD/FA was expected to be used for actual sewage treatment owing to its excellent uranium uptake efficiency/capacity, selectivity, cycle stability and feasibility of actual application.

Mussel inspired synthesis of polydopamine/polyethyleneimine-grafted fly ash composite adsorbent for the effective separation of U(VI)

Polydopamine/polyethyleneimine-grafted fly ash composite (PDA/PEI/FA), an efficient multifunctional adsorbent for U(VI) with excellent separation efficiency (94.5 %) and capacity (422.5 mg/g), was synthesized by grafting PDA and PEI on FA via Mussel inspiration and Michael addition reaction. The introduction of PDA and PEI had brought numerous functional groups with fine affinities to uranium, like catechol, amino and imino, causing good U(VI) separation performances. Langmuir and Pseudo-second-order models were well matched with experimental data, illustrating the U(VI) separation on PDA/PEI/FA was a homogeneous chemical adsorption process. After five cycles, the U(VI) adsorption efficiency for PDA/PEI/FA was still up to 90.2 %, implying that PDA/PEI/FA possessed good stability and reusability. Besides, the good dynamic adsorption performances of PDA/PEI/FA further demonstrated that PDA/PEI/FA was an ideal adsorbent for the practical wastewater treatment. According to the characterization results, U(VI) was absorbed by PAD/PEI/FA through complexation, redox reaction, electrostatic attraction and hydrogen bonding. Given the above, PDA/PEI/FA showed good practical application prospect in U(VI) separation.

Explorations on efficient extraction of uranium with porous coal fly ash aerogels

In order to explore a suitable uranium adsorbent with the advantages of low-cost, recyclability and high efficiency, porous coal fly ash aerogels with different size of coal fly ash were synthesized. Among them, PCFAA-1250 (prepared with 1250 mesh coal fly ash (CFA)) showed better adsorption performance and the maximum adsorption efficiency even approached 96.5% (C₀ = 10 mg L^-1, m/V = 1.0 g L^-1, T = 298 K, t = 24 h and pH = 3.0), which was higher than most of previous adsorbents. Langmuir and pseudo-second-order models were more likely to be used to determine the removal behavior of uranium on PCFAA, illustrating that the adsorption reaction was uniform chemisorption. Meanwhile, the adsorption process on PCFAA was spontaneous. Notably, the desorption efficiencies of all of PCFAA were more than 80% after five cycles, which suggested that PCFAA possessed good recyclability, especially PCFAA-1250. Besides, the adsorption mechanism was further revealed via XPS and the uranium ions were immobilized on the surface of adsorbents through complexation. Based on above conclusions, it could be concluded that PCFAA-1250 had the potential to be a candidate for the extraction of uranium from wastewater.

Nickel adsorption from waters onto Fe3O4/sugar beet pulp nanocomposite

In this study the magnetic nanocomposite material was synthesized with Fe₃O₄ impregnated to sugar beet pulp using chemical precipitation technique. Ni(II) removal performance of magnetic nanocomposite was investigated under different environmental conditions such as contact time, adsorbent dose, pH, initial heavy metal concentration, etc. The experimental studies have shown that, 81.2% Ni(II) removal efficiency was achieved at optimal conditions (25 mg/L initial Ni(II) concentration at 40 minute contact time, 200 rpm shaking speed, 5 g/L nanocomposite dose and pH 6.6). Freundlich and Langmuir isotherm experiments were performed and correlation coefficients were determined as 94.5% and 99.4%, respectively. The maximum adsorption capacity of material was achieved as 9.36 mg/g. These findings indicate that the adsorption that takes place is a monolayer process. The results of the pseudo-second order kinetic model (R² = 0.9947) indicate the chemisorptions process is used for Ni(II) removal using the electrostatic interaction. Thermodynamic studies illustrated that Ni(II) adsorption onto nanocomposite are exothermic and causes a decrease in the entropy. The adsorption of Ni(II) ions is non-spontaneous except for at low temperature and low initial concentrations. Nanocomposite characterization was illuminated with XRD, FT-IR, BET, TGA, TEM, SEM/EDX analysis.

Experimental design and RSM on the recovery of Ni (II) ions by ELM using TX-100 as a biodegradable surfactant

The present work deals with the extraction and pre-concentration of nickel (II) ions using emulsified liquid membrane (ELM) in the presence of di- (2-ethylhexyl) phosphoric acid (D2EHPA) as an extractant. The emulsion stability was achieved by the biodegradable surfactants Triton X-100 addition diluted in kerosene. Influence of operating conditions that affect ELM performance were investigated. A comparative study between the optimization parameters of this process was carried out both experimentally and with the Response Surface Methodology (RSM), in accordance with the Box-Behnken matrix. The following parameters were investegated: D2EHPA / Triton X-100 ratio between 0.5 and 3.5, initial concentration of the feed phase between 200 and 500 ppm and pH of the feed phase from 2.5-10. The transport of Ni (II) ions was evaluated according to the extraction yield as an analytical response and the optimal conditions were determined. It was found that the calculated values being in good agreement with experimental data that under the optimized conditions ([Ni] = 350 ppm, Vagitation = 200 rpm, t = 20 min and pH = 6.6), Ni (II) ions extraction was recorded more than 94% of efficiency.

A review of graphene-TiO2 and graphene-ZnO nanocomposite photocatalysts for wastewater treatment

Technologies for wastewater remediation have been growing ever since the environmental and health concern is realized. Development of nanomaterials has enabled mankind to have different methods to treat the various kinds of inorganic and organic pollutants present in wastewater from many resources. Among the many materials, semiconductor materials have found many environmental applications due to their outstanding photocatalytic activities. TiO₂ and ZnO are more effectively used as photocatalyst or adsorbents in the withdrawal of inorganic as well as organic wastes from the wastewater. On the other hand, graphene is tremendously being investigated for applications in environmental remediation in view of the superior physical, optical, thermal, and electronic properties of graphene nanocomposites. In this work, graphene-TiO₂ and graphene-ZnO nanocomposites have been reviewed for photocatalytic wastewater treatment. The various preparation techniques of these nanocomposites have been discussed. Also, different design strategies for graphene-based photocatalyst have been revealed. These nanocomposites exhibit promising applications in most of the water purification processes which are reviewed in this work. Along with this, the development of these nanocomposites using biomass-derived graphene has also been introduced. PRACTITIONER POINTS: Graphene-TiO₂ and graphene-ZnO nanocomposites are effective for wastewater treatment through photocatalysis. These nanocomposite photocatalysts have been used in the form of membrane as well as antibacterial agents. Synthetic strategies and design considerations of graphene-based photocatalyst play a major role. Biomass-derived graphene-TiO₂ and graphene-ZnO nanocomposites have also found application in wastewater treatment.

Zirconia aerogels for thermal management: Review of synthesis, processing, and properties information architecture

Zirconia aerogels are porous nanomaterials with high specific surface areas and low thermal conductivities that are suitable for a wide range of functions. The applications of zirconia aerogels include numerous uses in thermal management systems that are specifically beneficial in aeronautics and aerospace systems. This review seeks to detail the synthesis, processing, and characterization of these unique materials. However, the many distinctive synthesis pathways and processing conditions of zirconia aerogels can make the optimization of these materials difficult, potentially inhibiting further development. Independent variables in the synthesis process alone include zirconium precursor, rare earth stabilizer, solvent system, gelation agent, and surfactant templating agent. If only two distinct options were available for each synthetic variable, there would be up to 32 different synthetic pathways; if there were three options for each variable, 243 different synthetic pathways would be possible. Apart from the gel synthesis, processing conditions, including drying method, drying temperature, drying solvent, and sintering temperature, as well as various techniques used to characterize aerogels, need to be considered. To mitigate the sheer volume of synthetic parameters, this review uses an architected information structure to contemplate approximately 600 aerogel materials, along with the synthesis and processing conditions that make each material unique. By utilizing this information structure, containing over 10,000 relationships amongst 3,800 nodes, the connection between specific properties of zirconia aerogels and the pathways used to produce them can be more easily visualized, leading to a more effective understanding of the many variables that are used in the synthesis and processing of these materials. This review seeks to utilize data science in a way that can elucidate structure-property relationships in colloidal chemistry, providing a more efficient way to evaluate the synthesis and processing of materials with high experimental dimensionality.

Application of magnetic nanomaterials in magnetic in-tube solid-phase microextraction

Development of magnetic nanomaterials has greatly promoted the innovation of in-tube solid-phase microextraction. This review article gives an insight into recent advances in the modifications and applications of magnetic nanomaterials for in-tube solid-phase microextraction. Also, different magnetic nanomaterials which have recently been utilized as in-tube solid-phase microextraction sorbents are classified. This study shows that magnetic nanomaterials have gained significant attention owing to large specific surface area, selective absorption, and surface modification. Magnetic in-tube solid-phase microextraction has been applied for the analysis of food samples, biological, and environmental. However, for full development of magnetic in-tube SPME, effort is still needed to overcome limitations, such as mechanical stability, selectivity and low extraction efficiency. To achieve these objectives, research on magnetic in-tube SPME is mainly focused in the preparation of new extractive phases.

An overview on alumina-silica-based aerogels

Silica aerogels are remarkable materials with excellent physicochemical properties, such as high porosity and surface area, along with low density and thermal conductivity. In addition to their outstanding properties, these materials are quite interesting due to the possibility to change their chemistry according to intended applications. However, they also show some disadvantages, like low mechanical strength and poor dimensional stability under high temperatures (above 600 °C). Although these aerogels are frequently used as thermal insulators, for high temperature environments some of their properties need to be improved. The mixing with other ceramic thermally resistant phases is a viable approach. Thus, this work presents an overview on alumina-silica-based aerogels, describing their synthesis, processing and properties. The improvement on their properties will be discussed as a function of the amount of refractory phase (alumina) in the silica matrix. The introduction of the alumina phase makes them stable until 1200-1400 °C, maintaining low values of thermal conductivity at very high temperature (below 81 mW m^-1 K^-1). Finally, a brief survey on the most promising applications of these materials is presented, with several examples. In catalysis, alumina-silica aerogels have shown equivalent performance when compared to reference catalysts. In the field of thermal insulation, these materials show great potential, especially in high temperatures environments, due to their thermal dimensional stability and inherent low thermal conductivity. As adsorbents, higher stability and adsorption capacity were obtained with the incorporation of the alumina phase in silica aerogels, and these materials can be reused for repeated adsorption/desorption cycles. Indeed, a significant improvement of the aerogel performance by the synergetic effect of combining silica and alumina phases is usually obtained, supporting the expectation of the extension of their fields of application.

Insights into the competitive adsorption of pollutants on a mesoporous alumina-silica nano-sorbent synthesized from coal fly ash and a waste aluminium foil

A highly efficient and low-cost alumina-silica nano-sorbent was fabricated and characterized to understand the key factors responsible for its superiority over the existing adsorbents in treating the industry-discharged wastewater for the removal of dyes and heavy metals. As compared to the properties of raw fly ash, the following fundamental improvements were observed for the alumina-silica nano-sorbent: (a) transformation of throttled mesopores into slit-type pores, (b) increment in the surface area by 65-fold, (c) change in the morphology from spherical particles to a flake-type structure with sharp edges, (d) reduction in the average crystal size from 61.143 to 27.176 nm, and (e) increase in the pore volume from 0.005 to 0.50 cm3 g-1. These desired properties of the nano-sorbent were obtained by blending a waste aluminium foil with fly ash. This process increased the ratio of alumina to silica from 0.59 : 1 to an optimum ratio of 1.9 : 1, beyond which the particles agglomerated and the pore volume reduced. Eventually, the precipitated hydroxides were calcined at 700 °C that favoured the formation of γ-alumina. Moreover, this heat treatment changed its crystallinity and morphology of γ-alumina, which abruptly enhanced its activity towards the pollutants. The obtained product (nano-sorbent) was tested for the removal of lead and malachite green from a model wastewater solution over a wide range of initial pollutant concentrations and adsorbent dosages. After observing almost complete removal capacity and reusability for the pollutants, we propose this synthesized adsorbent as a universal material for treating industrial wastewater.

A retrospective and prospective of the use of bio- and nanomaterials for preconcentration, speciation, and determination of trace elements: a review spanning 25 years of research

This review covers the investigations carried out with my colleagues and students during the last 25 years aimed at the development of analytical procedures for the preconcentration and/or speciation analysis of trace and ultra-trace elements using bio- and nanosorbents employing different methodologies, analytical techniques, and instrumental approaches. In the last years, an important part of this research was based on the use of nanomaterials for preconcentration and/or speciation studies. For their properties, they constitute a break point in the evolution of analytical chemistry. Special attention was paid to carbon nanotubes (CNTs) that resulted effective sorbents in flow systems using different immobilization strategies to improve their sorption capabilities. They resulted unique tools for on-line solid-phase (micro)extraction methods providing the appropriate selectivity (clean-up) and sensitivity (preconcentration) to reach the expected levels of many elements in matrices of biological or environmental interest. The performance of the different substrates, their strengths and weaknesses for the determination of trace elements, and their species in different matrices by a variety of analytical techniques are discussed in detail, along with perspectives and possible challenges in future development. This survey contains 96 references and covers primarily the literature published over the last 25 years by our research group. Relevant publications on the topics discussed were also included.