Electrospun nanofiber: Emerging reinforcing filler in polymer matrix composite materials

Triple-Mechanism Enhanced Flexible SiO2 Nanofiber Composite Hydrogel with High Stiffness and Toughness for Cartilaginous Ligaments

Hydrogels are widely used in tissue engineering, soft robotics and wearable electronics. However, it is difficult to achieve both the required toughness and stiffness, which severely hampers their application as load-bearing materials. This study presents a strategy to develop a hard and tough composite hydrogel. Herein, flexible SiO2 nanofibers (SNF) are dispersed homogeneously in a polyvinyl alcohol (PVA) matrix using the synergistic effect of freeze-drying and annealing through the phase separation, the modulation of macromolecular chain movement and the promotion of macromolecular crystallization. When the stress is applied, the strong molecular interaction between PVA and SNF effectively disperses the load damage to the substrate. Freeze-dried and annealed-flexible SiO2 nanofibers/polyvinyl alcohol (FDA-SNF/PVA) reaches a preferred balance between enhanced stiffness (13.71 ± 0.28 MPa) and toughness (9.9 ± 0.4 MJ m-3). Besides, FDA-SNF/PVA hydrogel has a high tensile strength of 7.84 ± 0.10 MPa, super elasticity (no plastic deformation under 100 cycles of stretching), fast deformation recovery ability and excellent mechanical properties that are superior to the other tough PVA hydrogels, providing an effective way to optimize the mechanical properties of hydrogels for potential applications in artificial tendons and ligaments.

Fillers and methods to improve the effective (out-plane) thermal conductivity of polymeric thermal interface materials - A review

The internet of things and growing demand for smaller and more advanced devices has created the problem of high heat production in electronic equipment, which greatly reduces the work performance and life of the electronic instruments. Thermal interface material (TIM) is placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. The development of suitable TIM with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general, their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent developments in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (k⊥). For a better understanding of TC, a comprehensive background is presented. Several methods to improve the effective (out-plane) thermal conductivity of polymer composites and different theoretical models for the calculation of TC are also discussed. In the end, it is given a detailed conclusion that provides drawbacks of some fillers, multiple significant routes recommended by other researchers to build thermally conductive polymer composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer-based thermal interface material.

A Study of the Relationship between Polymer Solution Entanglement and Electrospun PCL Fiber Mechanics

Electrospun fibers range in size from nanometers to micrometers and have a multitude of potential applications that depend upon their morphology and mechanics. In this paper, we investigate the effect of polymer solution entanglement on the mechanical properties of individual electrospun polycaprolactone (PCL) fibers. Multiple concentrations of PCL, a biocompatible polymer, were dissolved in a minimum toxicity solvent composed of acetic acid and formic acid. The number of entanglements per polymer (ne) in solution was calculated using the polymer volume fraction, and the resultant electrospun fiber morphology and mechanics were measured. Consistent electrospinning of smooth fibers was achieved for solutions with ne ranging from 3.8 to 4.9, and the corresponding concentration of 13 g/dL to 17 g/dL PCL. The initial modulus of the resultant fibers did not depend upon polymer entanglement. However, the examination of fiber mechanics at higher strains, performed via lateral force atomic force microscopy (AFM), revealed differences among the fibers formed at various concentrations. Average fiber extensibility increased by 35% as the polymer entanglement number increased from a 3.8 ne solution to a 4.9 ne solution. All PCL fibers displayed strain-hardening behavior. On average, the stress increased with strain to the second power. Therefore, the larger extensibilities at higher ne also led to a more than double increase in fiber strength. Our results support the role of polymer entanglement in the mechanical properties of electrospun fiber at large strains.

Surface-Modified Electrospun Glass Nanofibers from Silane Treatment and Their Use for High-Performance Epoxy-Based Nanocomposite Materials

As a new and promising reinforcing filler, electrospun glass nanofibers (EGNFs) have attracted attention in the field of polymer composite materials. However, the reinforcing effectiveness of surface-modified EGNFs using different silane coupling agents in epoxy resin is still not quite clear. In this research, a series of silane coupling agents with increasing chain lengths in the order of methyl trimethoxysilane (MTMS), (3-aminopropyl) triethoxysilane (APTES), (3-glycidyloxypropyl) trimethoxysilane (GPTMS), and dual silane coupling agent APTES-GPTMS were employed to carry out surface treatment on the EGNFs. The pristine and silane functionalized EGNFs were then incorporated into epoxy resin as reinforcing fillers at low loading levels, i.e., 0.25 wt.%, 0.5 wt.%, and 1 wt.%, and the mechanical properties of the resultant epoxy nanocomposites, including strength, stiffness, ductility, and toughness, were evaluated. A commercial product of glass nanoparticles (GNPs) was used as a control to compare the reinforcing effectiveness of the EGNFs and the GNPs. This study revealed that the EGNFs could provide significant reinforcing and toughening effects at ultra-low loading (0.25 wt.%) in epoxy nanocomposite materials. Furthermore, surface modification of the EGNFs with silane coupling agents with long chain lengths, e.g., by using dual silane coupling agents, APTES-GPTMS, could enhance the interfacial bonding between the EGNFs and the epoxy matrix and further increase the mechanical performance of the EGNF-reinforced epoxy nanocomposite materials. Through this research, we realized epoxy nanocomposite materials with much-improved mechanical properties, i.e., 37%, 24%, 18%, 57% improvement in strength, stiffness, ductility, and toughness, respectively, with respect to those of the cured neat epoxy material with an ultra-low loading (0.25 wt.%) of APTES-GPTMS-EGNFs. Our research paves the road for developing lighter and stronger epoxy nanocomposite materials with EGNFs.

Nickel nanoparticle decorated silicon carbide as a thermal filler in thermal conductive aramid nanofiber-based composite films for heat dissipation applications

Aramid nanofibers (ANFs) have shown potential applications in the fields of nanocomposite reinforcement, battery separators, thermal insulation and flexible electronics. However, the inherent low thermal conductivity limits the application of ANFs, currently, to ensure long lifetime in electronics. In this work, new nickel (Ni) nanoparticles were employed to decorate the silicon carbide (SiC) filler by a rapid and non-polluting method, in which nickel acetate tetrahydrate (Ni(CH₃COO)₂·4H₂O) and SiC were mixed and heated under an inert atmosphere. The composites as thermal fillers were applied to prepare an aramid nanofiber (ANF)-based composite film. Our results showed that the decoration of SiC by an appropriate amount of Ni nanoparticles played an important role in improving the thermal conductivity, hydrophobicity, thermal stability, and puncture resistance of the ANF composite film. After adjusting the balling time at 10 h, the optimized content of 10 mol% Ni nanoparticles improved the thermal conductivity to 0.502 W m^-1 K^-1, 298.4% higher than that of the original ANF film. Moreover, increasing the content of thermal fillers to 30 wt% realized a high thermal conductivity of 0.937 W m^-1 K^-1, which is 643.7% higher than that of the pristine ANF film. Moreover, the compatibility between thermal fillers and ANFs and thermal stability were improved for the ANF-composite films. The effective heat transfer function of our composite films was further confirmed using a LED lamp and thermoelectric device. In addition, the obtained composite films show certain mechanical properties and better hydrophobicity; these results exhibit their great potential applications in electronic devices.

Optimizing the Rheological and Thermomechanical Response of Acrylonitrile Butadiene Styrene/Silicon Nitride Nanocomposites in Material Extrusion Additive Manufacturing

The current research aimed to examine the thermomechanical properties of new nanocomposites in additive manufacturing (AM). Material extrusion (MEX) 3D printing was utilized to evolve acrylonitrile butadiene styrene (ABS) nanocomposites with silicon nitride nano-inclusions. Regarding the mechanical and thermal response, the fabricated 3D-printed samples were subjected to a course of standard tests, in view to evaluate the influence of the Si3N4 nanofiller content in the polymer matrix. The morphology and fractography of the fabricated filaments and samples were examined using scanning electron microscopy and atomic force microscopy. Moreover, Raman and energy dispersive spectroscopy tests were accomplished to evaluate the composition of the matrix polymer and nanomaterials. Silicon nitride nanoparticles were proved to induce a significant mechanical reinforcement in comparison with the polymer matrix without any additives or fillers. The optimal mechanical response was depicted to the grade ABS/Si3N4 4 wt. %. An impressive increase in flexural strength (30.3%) and flexural toughness (47.2%) was found. The results validate that these novel ABS nanocomposites with improved mechanical properties can be promising materials.

A Review of Electrospun Nanofiber Interleaves for Interlaminar Toughening of Composite Laminates

Recently, polymeric nanofiber veils have gained lot of interest for various industrial and research applications. Embedding polymeric veils has proven to be one of the most effective ways to prevent delamination caused by the poor out-of-plane properties of composite laminates. The polymeric veils are introduced between plies of a composite laminate, and their targeted effects on delamination initiation and propagation have been widely studied. This paper presents an overview of the application of nanofiber polymeric veils as toughening interleaves in fiber-reinforced composite laminates. It presents a systematic comparative analysis and summary of attainable fracture toughness improvements based on electrospun veil materials. Both Mode I and Mode II tests are covered. Various popular veil materials and their modifications are considered. The toughening mechanisms introduced by polymeric veils are identified, listed, and analyzed. The numerical modeling of failure in Mode I and Mode II delamination is also discussed. This analytical review can be used as guidance for veil material selection, for estimation of the achievable toughening effect, for understanding the toughening mechanism introduced by veils, and for the numerical modeling of delamination.

In-situ forming dynamic covalently crosslinked nanofibers with one-pot closed-loop recyclability

Polymeric nanofibers are attractive nanomaterials owing to their high surface-area-to-volume ratio and superior flexibility. However, a difficult choice between durability and recyclability continues to hamper efforts to design new polymeric nanofibers. Herein, we integrate the concept of covalent adaptable networks (CANs) to produce a class of nanofibers ⎯ referred to dynamic covalently crosslinked nanofibers (DCCNFs) via electrospinning systems with viscosity modulation and in-situ crosslinking. The developed DCCNFs possess homogeneous morphology, flexibility, mechanical robustness, and creep resistance, as well as good thermal and solvent stability. Moreover, to solve the inevitable issues of performance degradation and crack of nanofibrous membranes, DCCNF membranes can be one-pot closed-loop recycled or welded through thermal-reversible Diels-Alder reaction. This study may unlock strategies to fabricate the next generation nanofibers with recyclable features and consistently high performance via dynamic covalent chemistry for intelligent and sustainable applications.

Unique Fiber Morphologies from Emulsion Electrospinning—A Case Study of Poly(ε-caprolactone) and Its Applications

The importance of electrospinning to produce biomimicking micro- and nano-fibrous matrices is realized by many who work in the area of fibers. Based on the solubility of the materials to be spun, organic solvents are typically utilized. The toxicity of the utilized organic solvent could be extremely important for various applications, including tissue engineering, biomedical, agricultural, etc. In addition, the high viscosities of such polymer solutions limit the use of high polymer concentrations and lower down productivity along with the limitations of obtaining desired fiber morphology. This emphasizes the need for a method that would allay worries about safety, toxicity, and environmental issues along with the limitations of using concentrated polymer solutions. To mitigate these issues, the use of emulsions as precursors for electrospinning has recently gained significant attention. Presence of dispersed and continuous phase in emulsion provides an easy route to incorporate sensitive bioactive functional moieties within the core-sheath fibers which otherwise could only be hardly achieved using cumbersome coaxial electrospinning process in solution or melt based approaches. This review presents a detailed understanding of emulsion behavior during electrospinning along with the role of various constituents and process parameters during fiber formation. Though many polymers have been studied for emulsion electrospinning, poly(ε-caprolactone) (PCL) is one of the most studied polymers for this technique. Therefore, electrospinning of PCL based emulsions is highlighted as unique case-study, to provide a detailed theoretical understanding, discussion of experimental results along with their suitable biomedical applications.

Controlled Deposition of Single-Walled Carbon Nanotubes Doped Nanofibers Mats for Improving the Interlaminar Properties of Glass Fiber Hybrid Composites

The properties of glass fiber composites were improved by strengthening the interlaminar regions using electrospun nanofibers mats. However, the chaotic nature of the electrospinning process at the collector restricts the controlled deposition and alignment of nanofibers and limits the use of electrospun nanofibers as secondary reinforcements. Hence, auxiliary vertical electrodes were used, which drastically reduced the diameter of the nanofibers from 450 nm to 150 nm and also improved the alignment of nanofibers. The aligned nanofibers were then used for doping the functionalized single-walled carbon nanotubes (f-SWCNTs) with nanofibers, which controlled the inherent issues associated with SWCNTs such as agglomeration, poor dispersion, and alignment. This process produced f-SWCNTs doped nanofiber mats. A series of tensile, three-point flexural, and Charpy impact tests showed that 30 vol% glass fiber composites reinforced with 0.5 wt% of randomly oriented nanofiber (RONFs) mats improved the properties of the hybrid composites compared to 0.1 wt%, 0.2 wt%, and 1 wt% RONFs mats reinforced glass fiber hybrid composites. The increase in properties for 0.5 wt% composites was attributed to the higher specific surface area and resistance to the relative slip within the interlaminar regions. The 0.5 wt% RONFs were then used to produce 0.5 wt% of continuous-aligned nanofiber (CANFs) mats, which showed improved mechanical properties compared to 0.5 wt% randomly oriented nanofiber (RONFs) mats reinforced hybrid composites. The CANFs mats with reduced diameter increased the tensile strength, flexural strength, and impact resistance by 4.71%, 17.19%, and 20.53%, respectively, as compared to the random nanofiber mats. The increase in properties could be attributed to the reduced diameter, controlled deposition, and alignment of the nanofibers. Further, the highest increase in mechanical properties was achieved by the addition of f-SWCNTs doped CANFs mats strengthened hybrid composites, and the increase was 30.34% for tensile strength, 30.18% for flexural strength, and 132.29% for impact resistance, respectively. This improvement in properties was made possible by orderly alignments of f-SWCNTs within the nanofibers. The SEM images further confirmed that auxiliary vertical electrodes (AVEs) reduced the diameter, improved the alignment and molecular orientation of the nanofibers, and thus helped to reinforce the f-SWCNTs within the nanomats, which improved the properties of the glass hybrid composites.

Electrospun Polymer Nanofibers: Processing, Properties, and Applications

Electrospun polymer nanofibers (EPNF) constitute one of the most important nanomaterials with diverse applications. An overall review of EPNF is presented here, starting with an introduction to the most attractive features of these materials, which include the high aspect ratio and area to volume ratio as well as excellent processability through various production techniques. A review of these techniques is featured with a focus on electrospinning, which is the most widely used, with a detailed description and different types of the process. Polymers used in electrospinning are also reviewed with the solvent effect highlighted, followed by a discussion of the parameters of the electrospinning process. The mechanical properties of EPNF are discussed in detail with a focus on tests and techniques used for determining them, followed by a section for other properties including electrical, chemical, and optical properties. The final section is dedicated to the most important applications for EPNF, which constitute the driver for the relentless pursuit of their continuous development and improvement. These applications include biomedical application such as tissue engineering, wound healing and dressing, and drug delivery systems. In addition, sensors and biosensors applications, air filtration, defense applications, and energy devices are reviewed. A brief conclusion is presented at the end with the most important findings and directions for future research.

Considering Electrospun Nanofibers as a Filler Network in Electrospun Nanofiber-Reinforced Composites to Predict the Tensile Strength and Young's Modulus of Nanocomposites: A Modeling Study

In this study, a simple approach was described to investigate the theoretical models for electrospun polymer nanofiber-reinforced nanocomposites. For predicting the tensile strength of the electrospun nylon 6 nanofiber-reinforced polyurethane acrylate composites, conventional Pukanszky, Nicolais-Narkis, Halpin-Tsai, and Neilson models were used, while for Young's modulus, Halpin-Tsai, modified Halpin-Tsai, and Hui-Shia models were used. As per the Pukanszky model, composite films showed better interaction since the values of the interaction parameter, B, were more than 3. Similarly, the value of an interfacial parameter, K, was less than 1.21 (K = -5, for the curve fitting) as per the Nicolais-Narkis model, which indicated better interfacial interaction. For composite films, the modified Halpin-Tsai model was revised again by introducing the orientation factor, α, which was 0.333 for the randomly oriented continuous nanofiber-reinforced composites, and the exponential shape factor, ξ = (2l/d)e-avf-b, which showed the best agreement with the experimental Young's modulus results. Based on mentioned remarks, these models would be applicable for estimating the tensile strength and Young's modulus of electrospun nanofiber-reinforced polymer composite films.

Improved Hydrolytic and Mechanical Stability of Sulfonated Aromatic Proton Exchange Membranes Reinforced by Electrospun PPSU Fibers

The hydrolytic stability of ionomer membranes is a matter of concern for the long-term durability of energy storage and conversion devices. Various reinforcement strategies exist for the improvement of the performances of the overall membrane. We propose in this article the stabilization of membranes based on aromatic ion conducting polymers (SPEEK and SPPSU) by the introduction of an electrospun mat of inexpensive PPSU polymer. Characterization data from hydrolytic stability (mass uptake and dimension change) and from mechanical and conductivity measurements show an improved stability of membranes in phosphate buffer, used for enzymatic fuel cells, and in distilled water. The synergistic effect of the reinforcement, together with the casting solvent and the thermal treatment or blending polymers, is promising for the realization of high stability ionomer membranes.

Fabrication of electrospun polyamide–weathered basalt nano-composite as a non-conventional membrane for basic and acid dye removal

Abstract

In this study, an adsorptive electrospun polyamide membrane (ESPA) and electrospun polyamide–weathered basalt composite membrane (ESPA-WB) were prepared by an electrospinning process at room temperature. Hence, the WB structure was built as a polymeric membrane separation film in combination with the ESPA matrix as a composite nano-filtration membrane. Then, the ESPA and ESPA-WB membranes were characterized using BET surface area analysis, Fourier transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy (SEM). To avoid cracks forming during the sintering process, the WB should be added in certain percentages. The microstructures of the prepared membranes were investigated to evaluate their efficiency for basic and acidic dyesʼ removal and their permeation flux. Compared with the ESPA, the ESPA-WB membrane combines the characteristics of WB and ESPA, which greatly enhances the performance of both methylene blue (MB) and methyl orange (MO) dyes removal from synthetic wastewater. The outcomes of this study indicated that the dye uptake in the case of ESPA-WB is higher than that of ESPA, and it decreases with an increase in dye concentrations. The obtained membrane ESPA-WB showed both an excellent anti-dye fouling and a good rejection property for both dyes (i.e. 90% rejection for MB and 74% for MO) with no sign of contamination by the applied dyes. It was found that the structure of the ESPA-WB membrane contains a large number of several adsorption sites which leads to an increase in the removal rate of dyes. Hence, this study demonstrated a non-conventional strategy to prepare an effective adsorptive nano-composite membrane that can be applied as a highly recyclable one for the removal of organic dyes.

Graphic abstract

Electrospun Nanofiber Composites for Drug Delivery: A Review on Current Progresses

A medication’s approximate release profile should be sustained in order to generate the desired therapeutic effect. The drug’s release site, duration, and rate must all be adjusted to the drug’s therapeutic aim. However, when designing drug delivery systems, this may be a considerable hurdle. Electrospinning is a promising method of creating a nanofibrous membrane since it enables drugs to be placed in the nanofiber composite and released over time. Nanofiber composites designed through electrospinning for drug release purposes are commonly constructed of simple structures. This nanofiber composite produces matrices with nanoscale fiber structure, large surface area to volume ratio, and a high porosity with small pore size. The nanofiber composite’s large surface area to volume ratio can aid with cell binding and multiplication, drug loading, and mass transfer processes. The nanofiber composite acts as a container for drugs that can be customized to a wide range of drug release kinetics. Drugs may be electrospun after being dissolved or dispersed in the polymer solution, or they can be physically or chemically bound to the nanofiber surface. The composition and internal structure of the nanofibers are crucial for medicine release patterns.

Optimization and characterization of polyhydroxybutyrate/lignin electro-spun scaffolds for tissue engineering applications

The tissue engineering scaffolds requires efficient combination of materials, appropriate method of preparation, and precise characterization of final product. In this study, the optimal electrospinning process conditions of polyhydroxybutyrate (PHB) were investigated by Taguchi design. Then, the initial PHB solution characteristics in the presence of lignin were optimized and then electro-spun. In this regard, the uniformity of electro-spun nanofibers, observed by SEM, confirmed that 9 w/v % is the optimum concentration of PHB in Trifluoro acetic acid. Addition of 6 wt% of lignin to PHB, could alleviate both the brittleness and hydrophobicity of PHB, as DSC, XRD, and WCA results indicated decrement in crystallinity (from 46 to 39 %), crystal size (from 21.8 to 15.2 nm), and WCA (from 118 to 73°). On the other hand, FESEM results represented diameter reduction from 1318 ± 202.07 to 442 ± 111.04 nm, and transformation of nanofiber physical structure from ribbon-like to cylindrical fiber by adding lignin. In addition, the mechanical properties of PHB including elongation at break, toughness, young modulus, and tensile strength were also improved (up to twice) by adding lignin. Ultimately, reviewing the outputs of degradation, bioactivity, MG63 cell viability, proliferation, mineralization, and antioxidant activity confirm that PHB/lignin electrospun scaffold has potential application in tissue engineering.

Centrifugal Spinning Enables the Formation of Silver Microfibers with Nanostructures

Silver nanowires (AgNWs) have received much attention and application in transparent electrodes, wearable electronic devices, and sensors. The hope is for these nanowires to eventually replace the most commonly used transparent electrode material—indium tin oxide (ITO). However, electrospinning used for the preparation of AgNWs on a large scale is limited by its low productivity and high electric field, while the alcohol-thermal method is limited to mixing by-product silver nanoparticles in silver nanowires. We demonstrate a novel and simple centrifugal spinning approach in order to successfully fabricate ultra-long silver microfibers based on AgNO₃ and polyvinyl pyrrolidone (PVP). The centrifugal-spun precursor fiber and silver fiber can be prepared to as thin as 390 and 310 nm, respectively. Annealed fibers show typical nanostructures with grains down to a minimum size of 51 nm. Combinations of different parameters, including concentrations of PVP, needle size, and annealing temperature are also investigated, in order to optimize the spinning process of ultra-long silver microfibers. The feasibility of preparing silver microfibers by centrifugal spinning is preliminarily verified, examining prospects for mass production. Furthermore, numerous strategies related to assisting the creation of silver nanofibers using centrifugal spinning are presented as possibilities in future development.

Hybrid composite of Nafion with surface-modified electrospun polybenzoxazine (PBz) fibers via ozonation as fillers for proton conducting membranes of fuel cells

Nafion was investigated for its compatibility in the preparation of hybrid composites with electrospun Polybenzoxazine (PBz) surface-modified fibers by evaluating the effects on the surface and structure of the composite. A PBz fiber mat was first crosslinked by thermal treatment after electrospinning to enhance the mechanical integrity of the fibers prior to modification. Further surface modification via free radical ozonation was carried out by potentiating oxygen-based functional groups of hydroxyl radicals (-OH) onto fibers' exposed surfaces. The sequential modifications by crosslinking and ozone treatment were evaluated by analyzing surface properties using XPS, ATR-FTIR and water contact angle which determined the enhanced properties of the fibers that were beneficial to the target functionality. Electron spectroscopy confirmed that fibers' surfaces were changed with the new surface chemistry without altering the chemical structure of PBz. The presence of higher oxygen-based functional groups on fibers' surfaces based on the resulting atomic compositions was correlated with the change in surface wettability by becoming hydrophilic with contact angle ranging from 21.27° to 59.83° compared to hydrophobic pristine PBz fibers. This is due to electrophilic aromatic substitution with hydroxyl groups present on the surfaces of the fibers endowed by ozonation. The resulting surface-modified fiber mat was used for the preparation of composites by varying two process parameters, the amount of Nafion dispersion and its homogenization and curing time, which was evaluated for compatibility and interaction as fillers to form hybrid composites. The analyses of SEM images revealed the effects of shorter homogenization and curing time on composites with rougher and wrinkled surfaces shown on the final hybrid composite's structure while decreasing the amount of Nafion at the same homogenization time but longer curing time showed its influence on improvement of compatibility and surface morphology.

Polymeric Nanofibers of Various Degrees of Crosslinking as Fillers in Poly(styrene-stat-n-butyl acrylate) Nanocomposites: Overcoming the Trade-Off between Tensile Strength and Stretchability

dummy This article is protected by copyright. All rights reserved.

Recent Trends in Biosensors for Environmental Quality Monitoring

The monitoring of environmental pollution requires fast, reliable, cost-effective and small devices. This need explains the recent trends in the development of biosensing devices for pollutant detection. The present review aims to summarize the newest trends regarding the use of biosensors to detect environmental contaminants. Enzyme, whole cell, antibody, aptamer, and DNA-based biosensors and biomimetic sensors are discussed. We summarize their applicability to the detection of various pollutants and mention their constructive characteristics. Several detection principles are used in biosensor design: amperometry, conductometry, luminescence, etc. They differ in terms of rapidity, sensitivity, profitability, and design. Each one is characterized by specific selectivity and detection limits depending on the sensitive element. Mimetic biosensors are slowly gaining attention from researchers and users due to their advantages compared with classical ones. Further studies are necessary for the development of robust biosensing devices that can successfully be used for the detection of pollutants from complex matrices without prior sample preparation.

Facile fabrication of electrospun g-C3N4/Bi12O17Cl2/poly(acrylonitrile-co-maleic acid) heterojunction nanofibers for boosting visible-light catalytic ofloxacin degradation

Electrospun g-C3N4/Bi12O17Cl2/poly(acrylonitrile-co-maleic acid) nanofibers were fabricated and applied for highly efficient removal of ofloxacin.

Nano-dimensional Spheres and Worms as Fillers in Polymer Nanocomposites: Effect of Filler Morphology

Polymeric nanofillers are prepared via polymerization induced self-assembly (PISA). Nano-dimensional spheres and worms are used to reinforce polymer nanocomposite film to investigate the effect of filler morphology and the effect...

Germanium-Titanium-π Polymer Composites as Functional Textiles for Clinical Strategy to Evaluate Blood Circulation Improvement and Sexual Satisfaction

By continuously enhancing the blood flow, far-infrared (FIR) textile is anticipated to be a potential non-pharmacological therapy in patients with peripheral vascular disorders, for instance, patients with end-stage renal disease (ESRD) undergoing hemodialysis (HD) and experiencing vasculogenic erectile dysfunction (VED). Hence, we manufactured a novel polymer composite, namely, germanium-titanium-π (Ge-Ti-π) textile and aimed to evaluate its characteristics and quality. We also investigated the immediate and long-term effects of the textile on patients with ESRD undergoing HD and experiencing VED. The Ge-Ti-π textile was found to have 0.93 FIR emissivity, 3.05 g/d strength, and 18.98% elongation. The results also showed a 51.6% bacteria reduction and negative fungal growth. On application in patients receiving HD, the Ge-Ti-π textile significantly reduced the limb numbness/pain (p < 0.001) and pain score on the visual analog scale (p < 0.001). Moreover, the Doppler ultrasound assessment data indicated a significant enhancement of blood flow in the right hand after 1 week of Ge-Ti-π textile treatment (p < 0.041). In VED patients, the Ge-Ti-π underpants treatment significantly improved the quality of sexual function and increased the average penile blood flow velocity after 3 months of the treatment. Our study suggests that the Ge-Ti-π textile could be beneficial for patients with blood circulation disorders.

A new mode of Thinfilm and Nanofiber for burst release of the drug for Alzheimer disease; A complete scenario from dispersible polymer to formulation methodology

Alzheimer's disease (AD) is usually caused intellectual deterioration which happened due to the degeneration of cholinergic neurons. Donepezil is employed for cholinesterase enzyme Inhibition (ChEI) to treat AD in a wider population. Over the years, researchers finding difficulties prompted through traditional dosage forms particularly in geriatric patience. To avoid swallowing difficulties brought about with the aid of the AD population, researchers majorly focused on oral thin-film technology (OTF). This technology strongly eliminates issues caused by solid oral dosage forms. It is one of the quality strategies to an alternate drug that is used in the first-pass metabolism or pre systematic metabolism. The solubility of the drug is a higher trouble and it can expand by way of lowering particle size. Nanofibers are the excellent desire to minimize the drug particles to the submicron stage and can increase the drug release rate drastically. It can be prepared by Electrospinning technology by incorporating polymeric material into poorly soluble drugs. Mostly natural and biodegradable polymers prefer in all pharmaceutical preparations. Polymers employed for oral delivery should be stable, possess mucoadhesive property, and should release the drug by diffusion, degradation, and swelling mechanism. The objective of the present review explains various thin-film and nanofiber formulations used for faster drug release in the treatment of Alzheimer's disease.

Dynamic Mechanical Properties and Thermal Properties of Longitudinal Basalt/Woven Glass Fiber Reinforced Unsaturated Polyester Hybrid Composites

This study investigates the mechanical, thermal, and chemical properties of basalt/woven glass fiber reinforced polymer (BGRP) hybrid polyester composites. The Fourier transform infrared spectroscopy (FTIR) was used to explore the chemical aspect, whereas the dynamic mechanical analysis (DMA) and thermomechanical analysis (TMA) were performed to determine the mechanical and thermal properties. The dynamic mechanical properties were evaluated in terms of the storage modulus, loss modulus, and damping factor. The FTIR results showed that incorporating single and hybrid fibers in the matrix did not change the chemical properties. The DMA findings revealed that the B7.5/G22.5 composite with 7.5 wt% of basalt fiber (B) and 22.5 wt% of glass fiber (G) exhibited the highest elastic and viscous properties, as it exhibited the higher storage modulus (8.04 × 10⁹ MPa) and loss modulus (1.32 × 10⁹ MPa) compared to the other samples. All the reinforced composites had better damping behavior than the neat matrix, but no further enhancement was obtained upon hybridization. The analysis also revealed that the B22.5/G7.5 composite with 22.5 wt% of basalt fiber and 7.5 wt% of glass fiber had the highest T_g at 70.80 °C, and increased by 15 °C compared to the neat matrix. TMA data suggested that the reinforced composites had relatively low dimensional stabilities than the neat matrix, particularly between 50 to 80 °C. Overall, the hybridization of basalt and glass fibers in unsaturated polyester formed composites with higher mechanical and thermal properties than single reinforced composites.

Understanding the Reinforcement of Graphene in Poly(Ether Ether Ketone)/Carbon Fibre Laminates

PEEK appears as an excellent candidate to substitute epoxy resins in carbon fibre laminates for high-performance aeronautical applications. The optimization of the properties and, in particular, of the transition region between the fibres and the matrix appear as a major issue prior to serial production. Graphene, modified with two compatibilizers, has been incorporated in the polymer layer with the purpose of imparting additional functionalities and enhancing the matrix-fibre interaction. It is found that both carbon fibres and modified graphene significantly influence the crystallization behaviour and smaller, and/or more imperfect crystals appear while the degree of crystallinity decreases. Despite this, nanoindentation studies show that the PEEK layer exhibits significant modulus improvements (≈30%) for 5 wt.% of graphene. Most importantly, the study of the local mechanical properties by nanoindentation mapping allows the identification of remarkably high modulus values close to the carbon fibre front. Such a relevant mechanical enhancement can be associated with the accumulation of graphene platelets at the polymer–fibre boundary, as revealed by electron microscopy studies. The results offer a feasible route for interlaminar mechanical improvement based on the higher density of graphene platelets at the fibre front that should promote interfacial interactions. Concerning electrical conductivity, a large anisotropy was found for all laminates, and values in the range ~10⁻⁴ S/cm were found for the through-thickness arrangement as a consequence of the good consolidation of the laminates.

Mechanically Strong and Electrochemically Stable Single-Ion Conducting Polymer Electrolytes Constructed from Hydrogen Bonding

Herein, composite membranes based on a single-ion conducting polymer electrolyte (SIPE) and poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) were prepared by an electrospinning technology. The SIPE with hydrogen bonding was obtained via reversible addition-fragmentation chain transfer (RAFT) copolymerization of 2-(3-(6-methyl-4-oxo-1,4-dihydropyrimidin-2-yl)ureido)ethyl methacrylate (UPyMA), poly(ethylene glycol) methyl ether methacrylate (PEGMA), and lithium 4-styrenesulfonyl (phenylsulfonyl) imide (SSPSILi). The obtained composite membrane exhibited a highly porous network structure, superior thermal stability (>300 °C), and high mechanical strength (17.3 MPa). The fabricated SIPE/PVDF-HFP composite membrane without lithium salts possessed a high ionic conductivity of 2.78 × 10^-5 S cm^-1 at 30 °C, excellent compatibility with the lithium metal electrode, and high lithium-ion transference number (0.89). The symmetric Li//Li cell exhibited a superior cycle performance without short circuit, indicating the generation of a stable interface between SIPE and the lithium metal electrode during the process of lithium plating/stripping, which could inhibit lithium dendrite growth in lithium metal batteries (LMBs). The Li//LiFePO₄ cell also exhibited superior cycle life and excellent rate capability at 60 or 25 °C. In consequence, the composite membrane exhibits a considerable future prospect for advanced LMBs.

Carrier Fibers for the Safe Dosage of Nanoparticles in Nanocomposites: Nanomechanical and Thermomechanical Study on Polycarbonate/Boehmite Electrospun Fibers Embedded in Epoxy Resin

The reinforcing effect of boehmite nanoparticles (BNP) in epoxy resins for fiber composite lightweight construction is related to the formation of a soft but bound interphase between filler and polymer. The interphase is able to dissipate crack propagation energy and consequently increases the fracture toughness of the epoxy resin. Usually, the nanoparticles are dispersed in the resin and then mixed with the hardener to form an applicable mixture to impregnate the fibers. If one wishes to locally increase the fracture toughness at particularly stressed positions of the fiber-reinforced polymer composites (FRPC), this could be done by spraying nanoparticles from a suspension. However, this would entail high costs for removing the nanoparticles from the ambient air. We propose that a fiber fleece containing bound nanoparticles be inserted at exposed locations. For the present proof-of-concept study, an electrospun polycarbonate nonwoven and taurine modified BNP are proposed. After fabrication of suitable PC/EP/BNP composites, the thermomechanical properties were tested by dynamic mechanical analysis (DMA). Comparatively, the local nanomechanical properties such as stiffness and elastic modulus were determined by atomic force microscopy (AFM). An additional investigation of the distribution of the nanoparticles in the epoxy matrix, which is a prerequisite for an effective nanocomposite, is carried out by scanning electron microscopy in transmission mode (TSEM). From the results it can be concluded that the concept of carrier fibers for nanoparticles is viable.

Functionalisable Epoxy-rich Electrospun Fibres Based on Renewable Terpene for Multi-Purpose Applications

New bio-based polymers capable of either outperforming fossil-based alternatives or possessing new properties and functionalities are of relevant interest in the framework of the circular economy. In this work, a novel bio-based polycarvone acrylate di-epoxide (PCADE) was used as an additive in a one-step straightforward electrospinning process to endow the fibres with functionalisable epoxy groups at their surface. To demonstrate the feasibility of the approach, poly(vinylidene fluoride) (PVDF) fibres loaded with different amounts of PCADE were prepared. A thorough characterisation by TGA, DSC, DMTA and XPS showed that the two polymers are immiscible and that PCADE preferentially segregates at the fibre surface, thus developing a very simple one-step approach to the preparation of ready-to-use surface functionalisable fibres. We demonstrated this by exploiting the epoxy groups at the PVDF fibre surface in two very different applications, namely in epoxy-based carbon fibre reinforced composites and membranes for ω-transaminase enzyme immobilisation for heterogeneous catalysis.

Physical and Mechanical Properties of Natural Leaf Fiber-Reinforced Epoxy Polyester Composites

In recent times, demand for light weight and high strength materials fabricated from natural fibres has increased tremendously. The use of natural fibres has rapidly increased due to their high availability, low density, and renewable capability over synthetic fibre. Natural leaf fibres are easy to extract from the plant (retting process is easy), which offers high stiffness, less energy consumption, less health risk, environment friendly, and better insulation property than the synthetic fibre-based composite. Natural leaf fibre composites have low machining wear with low cost and excellent performance in engineering applications, and hence established as superior reinforcing materials compared to other plant fibres. In this review, the physical and mechanical properties of different natural leaf fibre-based composites are addressed. The influences of fibre loading and fibre length on mechanical properties are discussed for different matrices-based composite materials. The surface modifications of natural fibre also play a crucial role in improving physical and mechanical properties regarding composite materials due to improved fibre/matrix adhesion. Additionally, the present review also deals with the effect of silane-treated leaf fibre-reinforced thermoset composite, which play an important role in enhancing the mechanical and physical properties of the composites.

Biodegradable shape-memory polymers and composites

Polymers have recently been making media headlines in various negative ways. To combat the negative view of those with no polymer experience, sustainable and biodegradable materials are constantly being researched. Shape-memory polymers, also known as SMPs, are a type of polymer material that is being extensively researched in the polymer industry. These SMPs can exhibit a change in shape because of an external stimulus. SMPs that are biodegradable or biocompatible are used extensively in medical applications. The use of biodegradable SMPs in the medical field has also led to research of the material in other applications. The following categories used to describe SMPs are discussed: net points, composition, stimulus, and shape-memory function. The addition of fillers or additives to the polymer matrix makes the SMP a polymer composite. Currently, biodegradable fillers are at the forefront of research because of the demand for sustainability. Common biodegradable fillers or fibers used in polymer composites are discussed in this chapter including Cordenka, hemp, and flax. Some other nonbiodegradable fillers commonly used in polymer composites are evaluated including clay, carbon nanotubes, bioactive glass, and Kevlar. The polymer and filler phase differences will be evaluated in this chapter. The recent advances in biodegradable shape-memory polymers and composites will provide a more positive perspective of the polymer industry and help to attain a more sustainable future.

High pressure laminates reinforced with electrospun cellulose acetate nanofibers

In the work, the non-woven cellulose acetate (CA) nanofiber mats were prepared via electrospinning, and CA nanofiber were incorporated into the core layer of the high-pressure laminates (HPLs). When the concentration of CA was 16 wt%, SEM images demonstrated that the morphology of the CA nanofiber mat was the best, with an average diameter of 654±246 nm. When CA nanofiber mats were incorporated into the core layer of HPLs, the mechanical properties of the resulted HPLs composites were significantly improved. Specifically, the tensile strength and elongation at break of the nanofiber mats reinforced HPLs composites increased remarkably to 40.8 ±1.1 MPa and 27.9 ± 0.9 %, respectively, which were nearly 6 times and 4.4 times higher than those of the pure HPLs. Furthermore, the incorporation of the CA nanofiber mats also significantly improved the flame retardancy of the HPLs, which was revealed from the thermogravimetric analysis (TGA) results.

Engineering and Characterization of Antibacterial Coaxial Nanofiber Membranes for Oil/Water Separation

In the present study, a coaxial nanofiber membrane was developed using the electrospinning technique. The developed membranes were fabricated from hydrophilic cellulose acetate (CA) polymer and hydrophobic polysulfone (PSf) polymer as a core and shell in an alternative way with addition of 0.1 wt.% of ZnO nanoparticles (NPs). The membranes were treated with a 2M NaOH solution to enhance hydrophilicity and thus increase water separation flux. Chemical and physical characterizations were performed, such as Fourier transform infrared (FTIR) spectroscopy, and surface wettability was measured by means of water contact angle (WCA), mechanical properties, surface morphology via field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and microscopy energy dispersive (EDS) mapping and point analysis. The results show higher mechanical properties for the coaxial nanofiber membranes which reached a tensile strength of 7.58 MPa, a Young's modulus of 0.2 MPa, and 23.4 M J.m-3 of toughness. However, treated mebranes show lower mechanical properties (tensile strength of 0.25 MPa, Young's modulus of 0.01 MPa, and 0.4 M J.m-3 of toughness). In addition, the core and shell nanofiber membranes showed a uniform distribution of coaxial nanofibers. Membranes with ZnO NPs showed a porous structure and elimination of nanofibers after treatment due to the formation of nanosheets. Interestingly, membranes changed from hydrophobic to hydrophilic (the WCA changed from 90 ± 8° to 14 ± 2°). Besides that, composite nanofiber membranes with ZnO NPs showed antibacterial activity against Escherichia coli. Furthermore, the water flux for the modified membranes was improved by 1.6 times compared to the untreated membranes.