1
|
Pinaeva LG, Noskov AS. Biodegradable biopolymers: Real impact to environment pollution. THE SCIENCE OF THE TOTAL ENVIRONMENT 2024; 947:174445. [PMID: 38981547 DOI: 10.1016/j.scitotenv.2024.174445] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/01/2024] [Revised: 06/25/2024] [Accepted: 07/01/2024] [Indexed: 07/11/2024]
Abstract
Biobased biodegradable polymers (BBP) derived from different renewable resources are commonly considered as attractive alternative to petroleum-based polymers, such as polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), etc. It is because they can address the issues of serious environmental problems resulted from accumulation of plastic wastes. In the review current methods of obtaining of most abundant BBP, polylactic acid (PLA) and polyhydroxybutyrate (PHB), have been studied with an emphasis on the toxicity of compounds used for their production and additives improving consumer characteristics of PLA and PHB based market products. Substantial part of additives was the same used for traditional polymers. Analysis of the data on the response of different organisms and plants on exposure to these materials and their degradation products confirmed the doubts about real safety of BBP. Studies of safer additives are scarce and are of vital importance. Meanwhile, technologies of recycling of traditional petroleum-based polymers were shown to be well-developed, which cannot be said about PLA or PHB based polymers, and their blends with petroleum-based polymers. Therefore, development of more environmentally friendly components and sustainable technologies of production are necessary before following market expansion of biobased biodegradable products.
Collapse
Affiliation(s)
- Larisa G Pinaeva
- Boreskov Institute of Catalysis SB RAS, Pr. Akad. Lavrentieva, 5, 630090 Novosibirsk, Russia.
| | - Aleksandr S Noskov
- Boreskov Institute of Catalysis SB RAS, Pr. Akad. Lavrentieva, 5, 630090 Novosibirsk, Russia.
| |
Collapse
|
2
|
Abbas-Abadi MS, Kusenberg M, Zayoud A, Roosen M, Vermeire F, Madanikashani S, Kuzmanović M, Parvizi B, Kresovic U, De Meester S, Van Geem KM. Thermal pyrolysis of waste versus virgin polyolefin feedstocks: The role of pressure, temperature and waste composition. WASTE MANAGEMENT (NEW YORK, N.Y.) 2023; 165:108-118. [PMID: 37119685 DOI: 10.1016/j.wasman.2023.04.029] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/05/2022] [Revised: 03/27/2023] [Accepted: 04/14/2023] [Indexed: 05/20/2023]
Abstract
Due to the complexity and diversity of polyolefinic plastic waste streams and the inherent non-selective nature of the pyrolysis chemistry, the chemical decomposition of plastic waste is still not fully understood. Accurate data of feedstock and products that also consider impurities is, in this context, quite scarce. Therefore this work focuses on the thermochemical recycling via pyrolysis of different virgin and contaminated waste-derived polyolefin feedstocks (i.e., low-density polyethylene (LDPE), polypropylene (PP) as main components), along with an investigation of the decomposition mechanisms based on the detailed composition of the pyrolysis oils. Crucial in this work is the detailed chemical analysis of the resulting pyrolysis oils by comprehensive two-dimensional gas chromatography (GC × GC) and ICP-OES, among others. Different feedstocks were pyrolyzed at a temperature range of 430-490 °C and at pressures between 0.1 and 2 bar in a continuous pilot-scale pyrolysis unit. At the lowest pressure, the pyrolysis oil yield of the studied polyolefins reached up to 95 wt%. The pyrolysis oil consists of primarily α-olefins (37-42 %) and n-paraffins (32-35 %) for LDPE pyrolysis, while isoolefins (mostly C9 and C15) and diolefins accounted for 84-91 % of the PP-based pyrolysis oils. The post-consumer waste feedstocks led to significantly less pyrolysis oil yields and more char formation compared to their virgin equivalents. It was found that plastic aging, polyvinyl chloride (PVC) (3 wt%), and metal contamination were the main causes of char formation during the pyrolysis of polyolefin waste (4.9 wt%).
Collapse
Affiliation(s)
- Mehrdad Seifali Abbas-Abadi
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium
| | - Marvin Kusenberg
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium
| | - Azd Zayoud
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium
| | - Martijn Roosen
- Laboratory for Circular Process Engineering (LCPE), Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, B-8500 Kortrijk, Belgium
| | - Florence Vermeire
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium
| | - Sepehr Madanikashani
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium; Materials and Process Engineering (IMAP), Institute of Mechanics, Materials and Civil Engineering (iMMC), Université catholique de Louvain - Place Sainte Barbe 2, B-1348 Louvain-la-Neuve, Belgium
| | - Maja Kuzmanović
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium; College of Polymer Science and Engineering, Sichuan University (Wangjiang campus), No.24 South Section 1, Yihuan Road, Chengdu 610065, China
| | - Behzad Parvizi
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium
| | | | - Steven De Meester
- Laboratory for Circular Process Engineering (LCPE), Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, B-8500 Kortrijk, Belgium
| | - Kevin M Van Geem
- Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering & Architecture, Ghent University, B-9052 Zwijnaarde, Belgium.
| |
Collapse
|