Biofouling and me: My Stockholm syndrome with biofilms

A comparison of the biofouling potential of field-collected and laboratory-cultured Ulva

The marine algae Ulva spp. are commonly used as model biofouling organisms. As biofouling studies are primarily conducted using field-collected specimens, factors including species identity, seasonal availability, and physiological status can hinder the replicability of the results. To address these limitations, a protocol was developed for the on-demand laboratory culture and release of Ulva zoospores. The biofouling potential of laboratory-cultured and field-collected Ulva blades was compared using a waterjet. No significant differences were found between field and laboratory-cultured samples in either spore adhesion (before waterjet) or the proportion of spores retained after waterjet exposure. However, there was significant variability within each session type in pre- and post-waterjet exposures, indicating that spore adhesion and retention levels vary significantly among trial runs. In addition, all our laboratory cultures were Ulva Clade C (LPP complex). In contrast, our field samples contained a mix of Ulva Clade C, U. compressa clade I, and U. flexuosa Clade D. This protocol for on-demand production of Ulva spores can improve biofouling research approaches, enables comparison of results across laboratories and regions, and accelerate the development of anti-biofouling strategies.

Effects of marine eutrophication environment on microbial corrosion: A review

Metal materials undergo severe corrosion in eutrophic environments. The effect of DO decay stimulated by high concentrations of nitrogen and phosphorus pollutants on microorganisms leads to the coupling of electrochemical and microbial corrosion processes. However, there are few studies on microbial corrosion mechanisms in eutrophic environments. This article discusses the corrosive factors of marine eutrophication, summarizes the impact of marine eutrophication on microbial corrosion and the potential mechanisms, including aerobic biofilm corrosion, aerobic & anaerobic mixed biofilm corrosion, and anaerobic microbial electron transfer corrosion, and expounds on the research methods for microbial corrosion of materials serving in estuarine areas prone to pollution. Microbial prevention and control, such as nutrient restriction and microbial interspecies competition, are of research value in the field of green protection. Microbial corrosion mechanisms studies in marine eutrophication environments are significant for environment monitor development, water intake and algae control technologies, and corrosion protection in polluted environments.

Quorum Quenching in Membrane Bioreactors for Fouling Retardation: Complexity Provides Opportunities

The occurrence of biofouling restricts the widespread application of membrane bioreactors (MBRs) in wastewater treatment. Regulation of quorum sensing (QS) is a promising approach to control biofouling in MBRs, yet the underlying mechanisms are complex and remain to be illustrated. A fundamental understanding of the relationship between QS and membrane biofouling in MBRs is lacking, which hampers the development and application of quorum quenching (QQ) techniques in MBRs (QQMBRs). While many QQ microorganisms have been isolated thus far, critical criteria for selecting desirable QQ microorganisms are still missing. Furthermore, there are inconsistent results regarding the QQ lifecycle and the effects of QQ on the physicochemical characteristics and microbial communities of the mixed liquor and biofouling assemblages in QQMBRs, which might result in unreliable and inefficient QQ applications. This review aims to comprehensively summarize timely QQ research and highlight the important yet often ignored perspectives of QQ for biofouling control in MBRs. We consider what this "information" can and cannot tell us and explore its values in addressing specific and important questions in QQMBRs. Herein, we first examine current analytical methods of QS signals and discuss the critical roles of QS in fouling-forming microorganisms in MBRs, which are the cornerstones for the development of QQ technologies. To achieve targeting QQ strategies in MBRs, we propose the substrate specificity and degradation capability of isolated QQ microorganisms and the surface area and pore structures of QQ media as the critical criteria to select desirable functional microbes and media, respectively. To validate the biofouling retardation efficiency, we further specify the QQ effects on the physicochemical properties, microbial community composition, and succession of mixed liquor and biofouling assemblages in MBRs. Finally, we provide scale-up considerations of QQMBRs in terms of the debated QQ lifecycle, practical synergistic strategies, and the potential cost savings of MBRs. This review presents the limitations of classic QS/QQ hypotheses in MBRs, advances the understanding of the role of QS/QQ in biofouling development/retardation in MBRs, and builds a bridge between the fundamental understandings and practical applications of QQ technology.

High-Resolution Large-Area Image Analysis Deciphers the Distribution of Salmonella Cells and ECM Components in Biofilms Formed on Charged PEDOT:PSS Surfaces

Biofilms, comprised of cells embedded in extracellular matrix (ECM), enable bacterial surface colonization and contribute to pathogenesis and biofouling. Yet, antibacterial surfaces are mainly evaluated for their effect on bacterial cells rather than the ECM. Here, a method is presented to separately quantify amounts and distribution of cells and ECM in Salmonella biofilms grown on electroactive poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS). Within a custom-designed biofilm reactor, biofilm forms on PEDOT:PSS surfaces electrically addressed with a bias potential and simultaneous recording of the resulting current. The amount and distribution of cells and ECM in biofilms are analyzed using a fluorescence-based spectroscopic mapping technique and fluorescence confocal microscopy combined with advanced image processing. The study shows that surface charge leads to upregulated ECM production, leaving the cell counts largely unaffected. An altered texture is also observed, with biofilms forming small foci or more continuous structures. Supported by mutants lacking ECM production, ECM is identified as an important target when developing antibacterial strategies. Also, a central role for biofilm distribution is highlighted that likely influences antimicrobial susceptibility in biofilms. This work provides yet a link between conductive polymer materials and bacterial metabolism and reveals for the first time a specific effect of electrochemical addressing on bacterial ECM formation.

Development of an analytical method to quantify N-acyl-homoserine lactones in bacterial cultures, river water, and treated wastewater

N-Acyl-homoserine lactones (AHL) play a major role in the communication of Gram-negative bacteria. They influence processes such as biofilm formation, swarming motility, and bioluminescence in the aquatic environment. A comprehensive analytical method was developed to elucidate the "chemical communication" in pure bacterial cultures as well as in the aquatic environment and engineered environments with biofilms. Due to the high diversity of AHLs and their low concentrations in water, a sensitive and selective LC-ESI-MS/MS method combined with solid-phase extraction was developed for 34 AHLs, optimized and validated to quantify AHLs in bacterial conditioned medium, river water, and treated wastewater. Furthermore, the developed method was optimized in terms of enrichment volume, internal standards, limits of detection, and limits of quantification in several matrices. An unanticipated variety of AHLs was detected in the culture media of Pseudomonas aeruginosa (in total 8 AHLs), Phaeobacter gallaeciensis (in total 6 AHLs), and Methylobacterium mesophilicum (in total 15 AHLs), which to our knowledge have not been described for these bacterial cultures so far. Furthermore, AHLs were detected in river water (in total 5 AHLs) and treated wastewater (in total 3 AHLs). Several detected AHLs were quantified (in total 24) using a standard addition method up to 7.3±1.0 µg/L 3-Oxo-C12-AHL (culture media of P. aeruginosa).

Achieving zero fouling in the ultrafiltration for secondary water supply systems in the absence of residual chlorine

Ultrafiltration (UF) technology is widely used in secondary water supply systems (SWSS) to provide high-quality drinking water. However, the challenge of severe membrane fouling, which leads to frequent cleaning requirements, makes UF maintenance intensive. In this study, we tried to validate the feasibility of achieving zero fouling without the need for cleaning in the UF for SWSS, i.e., the fouling resistance can be maintained for a very long time without any increase. We operated dead-end UF systems at different fluxes, both with and without residual chlorine, and monitored the formation of fouling layers during filtration. The results demonstrated the successful achievement of zero fouling under a flux of 10 L/(m2 h) in the absence of chlorine, evidenced by no increase in transmembrane pressure for three months. This zero-fouling phenomenon was attributed to the formation of a self-regulating biofouling layer. This biofouling layer could degrade the deposited foulants and featured a loose morphology, facilitated by microbial activities in the cake layer. Although residual chlorine reduced the fouling rate by half at a flux of 30 L/(m2 h), it hindered the achievement of zero fouling at the lower flux of 10 L/(m2 h), due to its inhibitory effect on microbial activity. Intermittent operation of UF was effective in achieving zero fouling at higher fluxes (e.g., 30 L/(m2 h)). This benefit was primarily ascribed to the biodegradation of accumulated foulants and the expansion of biofouling layer during the pause of the intermittent filtration, which prompted the formation of biofouling layers with loose structure and balanced composition. To the best of our knowledge, this study is the first attempt to achieve zero fouling in UF for SWSS, and the findings may offer valuable insights for the development of cleaning-free and low-maintenance membrane processes.

A review of experimental Assessment Processes of material resistance to marine and freshwater biofouling

Biofouling presents hazards to a variety of freshwater and marine underwater infrastructures and is one of the direct causes of species invasion. These negative impacts provide a unified goal for both industry practitioners and researchers: the development of novel antifouling materials to prevent the adhesion of biofouling. The prohibition of tributyltin (TBT) by the International Maritime Organization (IMO) in 2001 propelled the research and development of new antifouling materials. However, the evaluation process and framework for these materials remain incomplete and unsystematic. This mini-review starts with the classification and principles of new antifouling materials, discussing and summarizing the methods for assessing their biofouling resistance. The paper also compiles the relevant regulations and environmental requirements from different countries necessary for developing new antifouling materials with commercial potential. It concludes by highlighting the current challenges in antifouling material development and future outlooks. Systematic evaluation of newly developed antifouling materials can lead to the emergence of more genuinely applicable solutions, transitioning from merely laboratory products to materials that can be effectively used in real-world applications.

Emerging contaminants in the water environment: Disinfection-induced viable but non-culturable waterborne pathogens

Disinfection is essential for the control of waterborne pathogens (WPs), especially during the COVID-19 pandemic. WP can enter the viable but non-culturable (VBNC) state to evade disinfection, seriously threatening water safety. VBNC WPs should be considered as an emerging contaminant to ensure a higher level of safety of the water environment. Here, this study systematically reviewed the water disinfection methods that could induce WPs into the VBNC state, and clarified the risks of different species of VBNC WPs in the relevant water environment. The physicochemical and physiological properties of VBNC cells (e.g., morphology, physiology, and resuscitation potential) were then evaluated to better understand their potential health risks. In addition, the dominant detection methods of VBNC WPs were discussed, and real-time and label-free technologies were recommended for the study of VBNC WPs in the aquatic environment. The possible mechanisms of formation and persistence at the genetic level were highlighted. It concluded that the VBNC state has a deeper level of dormancy than the persistent state, which is associated with the general stress response and stringent response systems, and its persistence is also associated with the active efflux of harmful substances. Finally, the current shortcomings and research perspectives of VBNC bacteria were summarized. This review provides new insights into the characteristics, detection methods, persistence mechanisms, and potential health risks of VBNC WPs induced by water disinfection processes, and also serves as a basis for microbial risk control in the aquatic environment.

Plasmonic inhibition of bacterial adhesion on gold-decorated mesoporous zirconium oxide thin films

Preventing bacterial development on surfaces is essential to avoid problems caused by biofouling. Surfaces decorated with gold nanoparticles have been shown to thermally kill bacteria under high-intensity NIR illumination. In this study, we evaluated the colonization by E. coli of nanostructured surfaces composed of mesoporous zirconia thin films, both with and without gold nanoparticles embedded into the pores. We studied the effect of the nanostructure and of low intensity visible light excitation of the gold nanoparticles on the colonization process. We found that neither the zirconia, nor the presence of pores, or even gold nanoparticles affect bacterial adhesion compared to the bare glass substrate. Therefore, mesoporous zirconia thin films are biologically inert scaffolds that enable the construction of robust surfaces containing functional nanoparticles that can affect bacterial growth. When the gold containing surfaces are irradiated with light, bacterial adhesion shows a remarkable 96 ± 4% reduction. Our studies revealed that these surfaces affect early colonization steps, prior to biofilm formation, preventing bacterial adhesion without affecting its viability. In contrast to related systems where plasmonic excitation induces membrane damage due to strong local heating, the membrane integrity is preserved, showing that these surfaces have a different working principle.

Migration of surface-associated microbial communities in spaceflight habitats

Astronauts are spending longer periods locked up in ships or stations for scientific and exploration spatial missions. The International Space Station (ISS) has been inhabited continuously for more than 20 years and the duration of space stays by crews could lengthen with the objectives of human presence on the moon and Mars. If the environment of these space habitats is designed for the comfort of astronauts, it is also conducive to other forms of life such as embarked microorganisms. The latter, most often associated with surfaces in the form of biofilm, have been implicated in significant degradation of the functionality of pieces of equipment in space habitats. The most recent research suggests that microgravity could increase the persistence, resistance and virulence of pathogenic microorganisms detected in these communities, endangering the health of astronauts and potentially jeopardizing long-duration manned missions. In this review, we describe the mechanisms and dynamics of installation and propagation of these microbial communities associated with surfaces (spatial migration), as well as long-term processes of adaptation and evolution in these extreme environments (phenotypic and genetic migration), with special reference to human health. We also discuss the means of control envisaged to allow a lasting cohabitation between these vibrant microscopic passengers and the astronauts.

Enhanced Bacterium-Phage Symbiosis in Attached Microbial Aggregates on a Membrane Surface Facing Elevated Hydraulic Stress

Phages are increasingly recognized for their importance in microbial aggregates, including their influence on microbial ecosystem services and biotechnology applications. However, the adaptive strategies and ecological functions of phages in different aggregates remain largely unexplored. Herein, we used membrane bioreactors to investigate bacterium-phage interactions and related microbial functions within suspended and attached microbial aggregates (SMA vs AMA). SMA and AMA represent distinct microbial habitats where bacterial communities display distinct patterns in terms of dominant species, keystone species, and bacterial networks. However, bacteria and phages in both aggregates exhibited high lysogenicity, with 60% lysogenic phages in the virome and 70% lysogenic metagenome-assembled genomes of bacteria. Moreover, substantial phages exhibited broad host ranges (34% in SMA and 42% in AMA) and closely interacted with habitat generalist species (43% in SMA and 49% in AMA) as adaptive strategies in stressful operation environments. Following a mutualistic pattern, phage-carried auxiliary metabolic genes (pAMGs; 238 types in total) presumably contributed to the bacterial survival and aggregate stability. The SMA-pAMGs were mainly associated with energy metabolism, while the AMA-pAMGs were mainly associated with antioxidant biosynthesis and the synthesis of extracellular polymeric substances, representing habitat-dependent patterns. Overall, this study advanced our understanding of phage adaptive strategies in microbial aggregate habitats and emphasized the importance of bacterium-phage symbiosis in the stability of microbial aggregates.

Influence of water quality factors on cake layer 3D structures and water channels during ultrafiltration process

The three-dimensional (3D) structure of the cake layer, which could be influenced by water quality factors, plays a significant role in the ultrafiltration (UF) efficiency of water purification. However, it remains challenging to precisely reveal the variation of cake layer 3D structures and water channel characteristics. Herein, we systematically report the variation in the cake layer 3D structure at the nanoscale induced by key water quality factors and reveal its influence on water transport, in particular the abundance of water channels within the cake layer. In comparison with pH and Na+, Ca2+ played more significant role in determining cake layer structures. The sandwich-like cake layer, which was induced by the asynchronous deposition of humic acids and sodium alginate (SA), shifted to an isotropic structure when Ca2+ was present due to the Ca2+ bridging. In comparison with the sandwich-like structure, the isotropic cake layer has higher fractions of free volume (voids) and more water channels, leading to a 147% improvement in the water transport coefficient, 60% reduction in the cake layer resistance, and 21% increase in the final membrane specific flux. Our work elucidates a structure-property relationship where improving the isotropy of the cake layer 3D structure is conducive to the optimization of water channels and water transport within cake layers. This could inspire tailored regulation strategies for cake layers to enhance the UF efficiency of water purification.

Antibacterial and antibiofilm efficacy of green synthesized ZnO nanoparticles using Saraca asoca leaves

Biofilms are made up of bacterial colonies and their extracellular polymeric substances (EPS) matrix, which protects the bacteria from adverse environmental conditions. The increasing drug resistivity of pathogenic bacteria is becoming an emergency for developing new antibacterial agents. In this study, we have synthesized the zinc oxide nanoparticles (ZnO NPs) using the leaf extract of Saraca asoca plant, and the antibacterial and antibiofilm activity of green synthesized ZnO NPs was measured against the biofilm-producing bacteria Bacillus subtilis. The disk diffusion data reveals that the zone of inhibition (ZOI) starts at a concentration of 0.5 mg/mL and minimum inhibition concentration (100 µg/mL) and minimum bactericidal concentration (150 µg/mL) values were also evaluated for green synthesized ZnO nanomaterials. Crystal violet test and microscopic examination were used to assess the impact of produced nanoparticles on biofilm development. The findings indicated a nearly 45%, 64%, and 83% suppression of biofilm development at 0.5 × MIC, 0.75 × MIC, and 1 × MIC value, respectively. The biofilm biomass of the preformed or matured biofilms by the ZnO NPs was evaluated to be 68%, 50%, and 33% at concentrations of 0.5 × MIC, 0.75 × MIC, and 1 × MIC which was concentration-dependent. Moreover, flow cytometry results suggest damage to the bacterial cell membrane. The data indicated that the proportion of dead cells increased with NP concentration in comparison to the control. Therefore, it can be concluded that the green synthetic ZnO nanoparticles showed excellent antibacterial and antibiofilm activity against the Bacillus subtilis bacteria that produce biofilms and that they could be a promising substitute agent for the treatment of biofilms and drug-resistant bacteria.

Microbial Biofilms: Applications, Clinical Consequences, and Alternative Therapies

Biofilms are complex communities of microorganisms that grow on surfaces and are embedded in a matrix of extracellular polymeric substances. These are prevalent in various natural and man-made environments, ranging from industrial settings to medical devices, where they can have both positive and negative impacts. This review explores the diverse applications of microbial biofilms, their clinical consequences, and alternative therapies targeting these resilient structures. We have discussed beneficial applications of microbial biofilms, including their role in wastewater treatment, bioremediation, food industries, agriculture, and biotechnology. Additionally, we have highlighted the mechanisms of biofilm formation and clinical consequences of biofilms in the context of human health. We have also focused on the association of biofilms with antibiotic resistance, chronic infections, and medical device-related infections. To overcome these challenges, alternative therapeutic strategies are explored. The review examines the potential of various antimicrobial agents, such as antimicrobial peptides, quorum-sensing inhibitors, phytoextracts, and nanoparticles, in targeting biofilms. Furthermore, we highlight the future directions for research in this area and the potential of phytotherapy for the prevention and treatment of biofilm-related infections in clinical settings.

Patterned membranes for improving hydrodynamic properties and mitigating membrane fouling in water treatment: A review

Membrane technologies have been widely applied in water treatment over the past few decades. However, membrane fouling remains a hinderance for the widespread use of membrane processes because it decreases effluent quality and increases operating costs. To mitigate membrane fouling, researchers have been exploring effective anti-fouling strategies. Recently, patterned membranes are gaining attention as a novel non-chemical membrane modification for membrane fouling control. In this paper, we review the research on patterned membranes used in water treatment over the past 20 years. In general, patterned membranes show superior anti-fouling performances, which mainly results from two aspects: hydrodynamic effects and interaction effects. Due to the introduction of diversified topographies onto the membrane surface, patterned membranes yield dramatic improvements on hydrodynamic properties, e.g., shear stress, velocity field and local turbulence, restraining concentration polarization and foulants' deposition on the membrane surface. Besides, the membrane-foulant and foulant-foulant interactions play an important role in the mitigation of membrane fouling. Due to the existence of surface patterns, the hydrodynamic boundary layer is destroyed and the interaction force as well as the contact area between foulants and surface are decreased, which contributes to the fouling suppression. However, there are still some limitations in the research and application of patterned membranes. Future research is suggested to focus on the development of patterned membranes appropriate for different water treatment scenarios, the insights into the interaction forces affected by surface patterns, and the pilot-scale and long-term studies to verify the anti-fouling performances of patterned membranes in practical applications.

A peptide of PilZ domain-containing protein controls wastewater-treatment-membrane biofouling by inducing bacterial attachment

Membrane-based wastewater reclamation is used to mitigate water scarcity; however, irreversible biofouling is an elusive problem that hinders the efficiency of a forward-osmosis (FO) membrane-based process, and the protein responsible for fouling is unknown. Herein, we identified fouling proteins by analyzing the microbiome and proteome of wastewater extracellular polymeric substances responsible for strong irreversible FO-membrane fouling. The IGLSSLPR peptide of a PilZ domain-containing protein was found to recruit bacterial attachment when immobilized on the membrane surface while suppressing it when dissolved, in a similar manner to the Arg-Gly-Asp (RGD) peptide in mammalian cell cultures. Bacteria adhere to IGLSSLPR and poly-l-lysine-coated membranes with similar energies and exhibit water fluxes that decline similarly, which is ascribable to interaction as strong as electrostatic interactions in the peptide-coated membranes. We conclude that IGLSSLPR is the key domain responsible for membrane fouling and can be used to develop antifouling technology against bacteria, which is similar to the current usage of RGD peptide in mammalian cell cultures.

Fucoidan-Containing, Low-Adhesive Siloxane Coatings for Medical Applications: Inhibition of Bacterial Growth and Biofilm Development

The deposition of low-adhesive siloxane coatings is a current trend for the non-toxic control of bacterial growth and biofilm formation. Total elimination of biofilm formation has not been reported so far. The aim of this investigation was to study the ability of a non-toxic, natural, biologically active substance, such as fucoidan, to inhibit bacterial growth on similar medical coatings. The fucoidan amount was varied, and its impact on the bioadhesion-influencing surface characteristics, as well as on bacterial cell growth, was investigated. The inclusion of up to 3-4 wt.% brown algae-derived fucoidan in the coatings increases their inhibitory effect, more significantly on the Gram-positive bacterium S. aureus than on the Gram-negative bacterium Escherichia coli. The biological activity of the studied siloxane coatings was ascribed to the formation of a low-adhesive, biologically active surface top layer consisting of siloxane oil and dispersed water-soluble fucoidan particles. This is the first report on the antibacterial activity of fucoidan-containing medical siloxane coatings. The experimental results give reason to expect that relevantly selected, natural biologically active substances can be efficient in the non-toxic control of bacterial growth on medical devices and, as a result, medical device-associated infections.

A Magneto-Heated Silk Fibroin Scaffold for Anti-Biofouling Solar Steam Generation

Macroscopic 3D porous materials are ideal solar evaporators for water purification. However, the limited sunlight intensity and penetrating depth during solar-driven evaporation cannot prevent the biofouling formation by photothermal effect, thus leading to the deterioration of evaporation rate. Herein, a magnetic heating strategy is reported for anti-biofouling solar steam generation based on a magnetic silk fibroin (SF) scaffold with bi-heating property. Under one sun, the solar-heated top surface of magnetic SF scaffolds accelerates water evaporation at 2.03 kg m^-2 h^-1 , while the unheated inner channels suffer from the formation of biofilm. When exposed to alternating magnetic field (AMF), the magnetic SF scaffold can be integrally heated, leading to an efficient inner temperature to prevent biofouling in channels for water transportation. Accordingly, magneto-heated scaffolds show steady water evaporation rates after exposure to S. aureus and E. coli, which maintained 93.6-94.6% of original performance. In contrast, the evaporation rates of the scaffolds without AMF treatment are reduced to 1.31 (S. aureus) and 1.32 (E. coli) kg m^-2 h^-1 , decreased by 35.5% and 35.0%, respectively. In addition, the magneto-heated scaffold inhibits biofouling formation in natural lake water, maintaining 99.5% original performance.

Ultrasound-assisted synthesis of MIL-88(Fe) conjugated starch-Fe3O4 nanocomposite: A safe antibacterial carrier for controlled release of tetracycline

A constructing antibiotic carrier with a sustained release profile is a promising method to stop long-term bacterial infection, which is of ideal interest in different biomedical fields. To end this, the present study aims to design a novel carrier based on the modification of biopolymeric starch for the rising possible interaction between carrier and antibiotic agent. We established an in-situ ultrasound-assisted method was applied to grow and create MIL-88(Fe) framework in the structure of magnetic polysaccharide (i.e., St/Fe₃O₄) synthesized by precipitation method resulting in St/Fe₃O₄/MIL-88(Fe) nanocomposite. It was loaded with a high amount of Tetracycline (TC) through its immersion into the TC aqueous solution. The release profile of TC-loaded St/Fe₃O₄/MIL-88(Fe) displays a lower initial burst release (about 26 % after 12 h) and followed by a controlled and sustained release (about 73 % up to 168 h) in the simulated physiological environment at pH 7.4. The in vitro cytotoxicity showed good cytocompatibility against Human skin fibroblast (HFF-1) cells. TC-loaded St/Fe₃O₄/MIL-88(Fe) showed higher antibacterial activity against both S. aureus and E. coli with the MIC value of 64 and 128 μg·mL^-1, respectively.

The microbial growth potential of antiscalants used in seawater desalination

20 years since the first report on the biofouling potential of chemicals used for scale control, still, antiscalants with high bacterial growth potential are used in practice. Evaluating the bacterial growth potential of commercially available antiscalants is therefore essential for a rational selection of these chemicals. Previous antiscalant growth potential tests were conducted in drinking water or seawater inoculated with model bacterial species which do not represent natural bacterial communities. To reflect better on the conditions of desalination systems, we investigated the bacterial growth potential of eight different antiscalants in natural seawater and an autochthonous bacterial population as inoculum. The antiscalants differed strongly in their bacterial growth potential varying from ≤ 1 to 6 μg easily biodegradable C equivalents/mg antiscalant. The six phosphonate-based antiscalants investigated showed a broad range of growth potential, which depended on their chemical composition, whilst the biopolymer and the synthetic carboxylated polymers-based antiscalants showed limited or no significant bacterial growth. Moreover, nuclear magnetic resonance (NMR) scans enabled antiscalant fingerprinting, identifying components and contaminants, providing a rapid and sensitive characterization, and opening opportunities for rational selection of antiscalants for biofouling control.

Ciprofloxacin-Loaded Mixed Polymeric Micelles as Antibiofilm Agents

In this work, mixed polymeric micelles (MPMs) based on a cationic poly(2-(dimethylamino)ethyl methacrylate)-b-poly(ε-caprolactone)-b-poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA₂₉-b-PCL₇₀-b-PDMAEMA₂₉) and a non-ionic poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) (PEO₉₉-b-PPO₆₇-b-PEO₉₉) triblock copolymers, blended at different molar ratios, were developed. The key physicochemical parameters of MPMs, including size, size distribution, and critical micellar concentration (CMC), were evaluated. The resulting MPMs are nanoscopic with a hydrodynamic diameter of around 35 nm, and the ζ-potential and CMC values strongly depend on the MPM's composition. Ciprofloxacin (CF) was solubilized by the micelles via hydrophobic interaction with the micellar core and electrostatic interaction between the polycationic blocks, and the drug localized it, to some extent, in the micellar corona. The effect of a polymer-to-drug mass ratio on the drug-loading content (DLC) and encapsulation efficiency (EE) of MPMs was assessed. MPMs prepared at a polymer-to-drug mass ratio of 10:1 exhibited very high EE and a prolonged release profile. All micellar systems demonstrated their capability to detach pre-formed Gram-positive and Gram-negative bacterial biofilms and significantly reduced their biomass. The metabolic activity of the biofilm was strongly suppressed by the CF-loaded MPMs indicating the successful drug delivery and release. The cytotoxicity of empty and CF-loaded MPMs was evaluated. The test reveals composition-dependent cell viability without cell destruction or morphological signs of cell death.

Antifouling potential of enzymes applied to Reverse Osmosis Membranes

Many companies in the food industry apply reverse osmosis (RO) membranes to ensure high-quality reuse of water. Biofouling is however, a common, recalcitrant and recurring problem that blocks transport over membranes and decreases the water recovery. Microorganisms adhering to membranes may form biofilm and produce an extracellular matrix, which protects against external stress and ensures continuous attachment. Thus, various agents are tested for their ability to degrade and disperse biofilms. Here, we identified industrially relevant bacterial model communities that form biofilms on RO membranes used for treating process water before reuse. There was a marked difference in the biofilm forming capabilities of bacteria isolated from contaminated RO membranes. One species, Raoultella ornithinolytica, was particularly capable of forming biofilm and was included in most communities. The potential of different enzymes (Trypsin-EDTA, Proteinase K, α-Amylase, β-Mannosidase and Alginate lyase) as biofouling dispersing agents was evaluated at different concentrations (0.05 U/ml and 1.28 U/ml). Among the tested enzymes, β-Mannosidase was the only enzyme able to reduce biofilm formation significantly within 4 h of exposure at 25 °C (0.284 log reduction), and only at the high concentration. Longer exposure duration, however, resulted in significant biofilm reduction by all enzymes tested (0.459-0.717 log reduction) at both low and high concentrations. Using confocal laser scanning microscopy, we quantified the biovolume on RO membranes after treatment with two different enzyme mixtures. The application of proteinase K and β-Mannosidase significantly reduced the amount of attached biomass (43% reduction), and the combination of all five enzymes showed even stronger reducing effect (71% reduction). Overall, this study demonstrates a potential treatment strategy, using matrix-degrading enzymes for biofouled RO membranes in food processing water treatment streams. Future studies on optimization of buffer systems, temperature and other factors could facilitate cleaning operations based on enzymatic treatment extending the lifespan of membranes with a continuous flux.

Progress towards Stable and High-Performance Polyelectrolyte Multilayer Nanofiltration Membranes for Future Wastewater Treatment Applications

The increasing demand for nanofiltration processes in drinking water treatment, industrial separation and wastewater treatment processes has highlighted several shortcomings of current state-of-the-art thin film composite (TFC NF) membranes, including limitations in chemical resistance, fouling resistance and selectivity. Polyelectrolyte multilayer (PEM) membranes provide a viable, industrially applicable alternative, providing significant improvements in these limitations. Laboratory experiments using artificial feedwaters have demonstrated selectivity an order of magnitude higher than polyamide NF, significantly higher fouling resistance and excellent chemical resistance (e.g., 200,000 ppmh chlorine resistance and stability over the 0-14 pH range). This review provides a brief overview of the various parameters that can be modified during the layer-by-layer procedure to determine and fine-tune the properties of the resulting NF membrane. The different parameters that can be adjusted during the layer-by-layer process are presented, which are used to optimize the properties of the resulting nanofiltration membrane. Substantial progress in PEM membrane development is presented, particularly selectivity improvements, of which the most promising route seems to be asymmetric PEM NF membranes, offering a breakthrough in active layer thickness and organic/salt selectivity: an average of 98% micropollutant rejection coupled with a NaCl rejection below 15%. Advantages for wastewater treatment are highlighted, including high selectivity, fouling resistance, chemical stability and a wide range of cleaning methods. Additionally, disadvantages of the current PEM NF membranes are also outlined; while these may impede their use in some industrial wastewater applications, they are largely not restrictive. The effect of realistic feeds (wastewaters and challenging surface waters) on PEM NF membrane performance is also presented: pilot studies conducted for up to 12 months show stable rejection values and no significant irreversible fouling. We close our review by identifying research areas where further studies are needed to facilitate the adoption of this notable technology.

Dry surface biofilms in the food processing industry: An overview on surface characteristics, adhesion and biofilm formation, detection of biofilms, and dry sanitization methods

Bacterial biofilm formation in low moisture food processing (LMF) plants is related to matters of food safety, production efficiency, economic loss, and reduced consumer trust. Dry surfaces may appear dry to the naked eye, however, it is common to find a coverage of thin liquid films and microdroplets, known as microscopic surface wetness (MSW). The MSW may favor dry surface biofilm (DSB) formation. DSB formation is similar in other industries, it occurs through the processes of adhesion, production of extracellular polymeric substances, development of microcolonies and maturation, it is mediated by a quorum sensing (QS) system and is followed by dispersal, leading to disaggregation. Species that survive on dry surfaces develop tolerance to different stresses. DSB are recalcitrant and contribute to higher resistance to sanitation, becoming potential sources of contamination, related to the spoilage of processed products and foodborne disease outbreaks. In LMF industries, sanitization is performed using physical methods without the presence of water. Although alternative dry sanitizing methods can be efficiently used, additional studies are still required to develop and assess the effect of emerging technologies, and to propose possible combinations with traditional methods to enhance their effects on the sanitization process. Overall, more information about the different technologies can help to find the most appropriate method/s, contributing to the development of new sanitization protocols. Thus, this review aimed to identify the main characteristics and challenges of biofilm management in low moisture food industries, and summarizes the mechanisms of action of different dry sanitizing methods (alcohol, hot air, UV-C light, pulsed light, gaseous ozone, and cold plasma) and their effects on microbial metabolism.

Semantic segmentation for fully automated macrofouling analysis on coatings after field exposure

Biofouling is a major challenge for sustainable shipping, filter membranes, heat exchangers, and medical devices. The development of fouling-resistant coatings requires the evaluation of their effectiveness. Such an evaluation is usually based on the assessment of fouling progression after different exposure times to the target medium (e.g. salt water). The manual assessment of macrofouling requires expert knowledge about local fouling communities due to high variances in phenotypical appearance, has single-image sampling inaccuracies for certain species, and lacks spatial information. Here an approach for automatic image-based macrofouling analysis was presented. A dataset with dense labels prepared from field panel images was made and a convolutional network (adapted U-Net) for the semantic segmentation of different macrofouling classes was proposed. The establishment of macrofouling localization allows for the generation of a successional model which enables the determination of direct surface attachment and in-depth epibiotic studies.

Positive biofilms to guide surface microbial ecology in livestock buildings

The increase in human consumption of animal proteins implies changes in the management of meat production. This is followed by increasingly restrictive regulations on antimicrobial products such as chemical biocides and antibiotics, used in particular to control pathogens that can spread zoonotic diseases. Aligned with the One Health concept, alternative biological solutions are under development and are starting to be used in animal production. Beneficial bacteria able to form positive biofilms and guide surface microbial ecology to limit microbial pathogen settlement are promising tools that could complement existing biosecurity practices to maintain the hygiene of livestock buildings. Although the benefits of positive biofilms have already been documented, the associated fundamental mechanisms and the rationale of the microbial composition of these new products are still sparce. This review provides an overview of the envisioned modes of action of positive biofilms used on livestock building surfaces and the resulting criteria for the selection of the appropriate microorganisms for this specific application. Limits and advantages of this biosecurity approach are discussed as well as the impact of such practices along the food chain, from farm to fork.

Advances in experimental and computational methodologies for the study of microbial-surface interactions at different omics levels

The study of the biological response of microbial cells interacting with natural and synthetic interfaces has acquired a new dimension with the development and constant progress of advanced omics technologies. New methods allow the isolation and analysis of nucleic acids, proteins and metabolites from complex samples, of interest in diverse research areas, such as materials sciences, biomedical sciences, forensic sciences, biotechnology and archeology, among others. The study of the bacterial recognition and response to surface contact or the diagnosis and evolution of ancient pathogens contained in archeological tissues require, in many cases, the availability of specialized methods and tools. The current review describes advances in in vitro and in silico approaches to tackle existing challenges (e.g., low-quality sample, low amount, presence of inhibitors, chelators, etc.) in the isolation of high-quality samples and in the analysis of microbial cells at genomic, transcriptomic, proteomic and metabolomic levels, when present in complex interfaces. From the experimental point of view, tailored manual and automatized methodologies, commercial and in-house developed protocols, are described. The computational level focuses on the discussion of novel tools and approaches designed to solve associated issues, such as sample contamination, low quality reads, low coverage, etc. Finally, approaches to obtain a systems level understanding of these complex interactions by integrating multi omics datasets are presented.

Precise portrayal of microscopic processes of wastewater biofilm formation: Taking SiO2 as the model carrier

Precise characterization of the microscopic processes of wastewater biofilm formation is essential for regulating biofilm behavior. Nevertheless, it remains a great challenge. This study investigated biofilm formation on SiO₂ carriers under gradually increasing shear force combining the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory in a Couette-Taylor reactor, and precisely revealed the micro-interface interaction and species colonization during biofilm formation. The results indicated that bacterial reversible adhesion distance on SiO₂ carrier surface was 3.06 ± 0.48 nm. Meanwhile, the secondary minimum of total XDLVO interaction energy could be used as a novel indicator to distinguish biofilm formation stages. The revealed biofilm formation stages were also confirmed by the electrochemical analysis. Additionally, the pioneer species that colonized at first were Comamonadaceae, Azospira, Flavobacterium and Azonexus, while keystone species such as Hydrogenophaga, AKYH767, Aquimonas and Ignavibacterium determined the stability of microbial community. In conclusion, this study provided a methodological example to study wastewater biofilm micro-interface behavior through the integration of an experimental platform as well as multiple monitoring and analysis methods, which opened up new perspectives for biofilm research and provided useful guidance for the regulation of biofilm-related treatment processes and new technology development.

Dynamic Changes in Biofilm Structures under Dynamic Flow Conditions

Detachment is an important process determining the structure and function of bacterial biofilm, which has significant implications for biogeochemical cycling of elements, biofilm application, and infection control in clinical settings. Quantifying the responses of biofilm structure to hydrodynamics is crucial for understanding biofilm detachment mechanisms in aquatic environments.

Effects of Biofilms on Trace Metal Adsorption on Plastics in Freshwater Systems

The formation of plastisphere on plastics and their potential impact on freshwater ecosystems have drawn increasing attention. However, there is still limited information about the effects of plastisphere on the heavy metal adsorption capacity and the related mechanism of plastic debris in different freshwaters. Herein, the trace metal adsorption capacity, kinetics and adsorption mechanisms of virgin and biofilm-covered plastic debris were investigated. Polypropylene (PP) and polyethylene terephthalate (PET) plastic debris were placed in three freshwaters (Xuanwu Lake, Donghu Lake and the Qinhuai River) for 45 days to incubate biofilms. Batch adsorption experiments were performed to compare the adsorption processes of trace metal on virgin and biofilm-covered plastics. Results showed that biofilms increase the adsorption of metals on plastics, and the adsorption isotherms were well fitted by the Langmuir model. Furthermore, the adsorption capacities for lead (Pb(II)) were higher than that of cadmium (Cd(II)) and zinc (Zn(II)), with 256.21 and 277.38 μg/g (Pb(II)) adsorbed in biofilm-covered PP and PET, respectively, in Xuanwu Lake. The adsorption kinetics of metals on plastic debris were significantly affected by the biofilms, by switching the intraparticle diffusion for virgin plastic debris to film diffusion for the biofilm-covered plastic debris. Moreover, the complexation of functional groups within the biofilms might mainly contribute to the increases of metal adsorption, involving the participation of oxygen and nitrogen groups. Overall, these results suggested that biofilms reinforce the potential role of plastics as a carrier of trace metals in freshwaters.

Green β-cyclodextrin-based corrosion inhibitors: Recent developments, innovations and future opportunities

β-Cyclodextrin-based compounds are used to develop and innovate materials that protect against corrosion due to their sustainability, low cost, environmental friendliness, excellent water solubility and high inhibition efficiency. However, corrosion potentials of β-CD-based compounds were not reviewed with the modern trends. The essence of the problem is that a deep understanding of the development and innovation of β-CD-based compounds as corrosion inhibitors is very important in creating next-generation materials for corrosion protection. In this review, the fundamental behaviour, importance, developments and innovations of β-CD modified with natural and synthetic polymers, β-CD grafted with the organic compounds, β-CD-based supramolecular (host-guest) systems with organic molecules, polymer β-CD-based supramolecular (host-guest) systems, β-CD-based graphene oxide materials, β-CD-based nanoparticle materials and β-CD-based nanocarriers as corrosion inhibitors for various metals were reviewed and discussed with recent research works as examples. In addition, the corrosion inhibition of β-CD-based compounds for biocorrosion, microbial corrosion and biofouling was reviewed. It was found that (i) these compounds are sustainable, inexpensive, environmentally friendly, and highly water-soluble and have high inhibition efficiency; (ii) the molecular structure of β-CD makes it an excellent molecular container for corrosion inhibitors compounds; (iii) the β-CD is excellent core to develop the next generation of corrosion inhibitors. It is recommended that (i) β-CD compounds would be synthesized by green methods, such as using biological sustainable catalysts and green solvents, green methods include irradiation or heating, energy-efficient microwave irradiation, mechanochemical mixing, solid-state reactions, hydrothermal reactions and multicomponent reactions; (ii) this review will be helpful in creating, enhancing and innovating the next green and efficient materials for future corrosion protection in high-impact industries.

The effect of different carbon sources on biofouling in membrane fouling simulators: microbial community and implications

Biofouling is a problem affecting the operation of nanofiltration systems due to the complexity of the carbon matrix affecting bacteria and biofilm growth. This study used membrane fouling simulators to investigate the effects of five different carbon sources on the biofouling of nanofiltration membranes. For all the carbon sources analyzed, the increase in pressure drop was most accelerated for acetate. The use of acetate as the single carbon source produced less adenosine triphosphate but more extracellular polymers than glucose. The microbial community was analyzed using 16 s rRNA. The use of more than a single carbon source produced an increase in bacteria diversity even at similar concentrations. The relative abundance of proteobacteria was the highest at the phylum level (95%) when a single carbon source was added. Additionally, it was found that the use of different carbon sources produced a shift in the microbial community, affecting the biofouling and pressure drop on membranes.

Microbial resistance to sanitizers in the food industry: review

Hygiene programs which comprise the cleaning and sanitization steps are part of the Good Hygiene Practices (GHP) and are considered essential to ensure food safety and quality. Inadequate hygiene practices may contribute to the occurrence of foodborne diseases, development of microbial resistance to sanitizers, and economic losses. In general, the sanitizer resistance is classified as intrinsic or acquired. The former is an inherent characteristic, naturally present in some microorganisms, whereas the latter is linked to genetic modifications that can occur at random or after continuous exposure to a nonnormal condition. The resistance mechanisms can involve changes in membrane permeability or in the efflux pump, and enzymatic activity. The efflux pump mechanism is the most elucidated in relation to the resistance caused by the use of different types of sanitizers. In addition, microbial resistance to sanitizers can also be favored in the presence of biofilms due to the protection given by the glycocalyx matrix and genetic changes. Therefore, this review aimed to show the main microbial resistance mechanisms to sanitizers, including genetic modifications, biofilm formation, and permeability barrier.

Electrospun Nanofibrous Membranes Accelerate Biofilm Formation and Probiotic Enrichment: Enhanced Tolerances to pH and Antibiotics

Biofilms are the oldest, most successful, and most widely distributed form of microorganism life on earth, existing even in extreme environments. Presently, probiotics in biofilm phenotype are thought as the most advanced fourth-generation probiotics. However, high-efficiency and large-scale biofilm enrichment in an artificial way is difficult. Here, fibrous membranes as probiotic biofilm-enriching materials are studied. Electrospun cellulose acetate nanofibrous membranes with nano-sized fibers show outstanding superiority over fibrous membranes with micron-sized fibers in Lactobacillus paracasei biofilm enrichment. The special 3D structure of electrospun nanofibrous membranes makes other facilitating biofilm formation factors insignificant. With a suitable scaffold/culture medium ratio, nearly 100% of L. paracasei cells exist as biofilm phenotype on the membrane from the very beginning, not planktonic state. L. paracasei biofilms possess a potential for long-term survival and high tolerances toward strong acidic and alkali conditions and antibiotics. RNA sequencing results explain why L. paracasei biofilms possess high tolerances toward harsh environments as compared to planktonic L. paracasei. Electrospun nanofibrous membranes can serve as powerful biofilm-enriching scaffolds for probiotics and other valuable microbes.

Hydrophilic tyrosine-based phenolic resin with micro-ripples morphology for marine antifouling application

Since biofouling challenges negatively influence the marine and transportation industries, developing effective antifouling materials have attracted extensive concern. A tyrosine-based antifouling phenolic resin (TPP resin) was synthesized using tyrosine as a natural phenol source. TPP exhibited shell-like surface morphology with micro-ripples and excellent anti-adhesion properties against bacteria and diatom. The micro-ripples surface might be caused by the strong hydrogen bonding or ionic interaction among tyrosine units resulting in microphase separation during the curing process. Tyrosine content in TPP resin has a great influence on the surface properties, morphology and antifouling characteristics. The higher the tyrosine content, the higher is the surface hydrophilicity, the denser and more regular is the micro-ripples morphology, and the stronger is the antifouling performance. TPP-60 % exhibited the best antifouling performance. Combination of the surface hydrophilicity and regular micro-ripples surface morphology afford TPP excellent antifouling performance. TPP resins offer a broad prospect for developing phenolic resin in the antifouling field.

Quantitative proteomics and phosphoproteomics elucidate the molecular mechanism of nanostructured TiO2-stimulated biofilm formation

With the increasing concerns regarding bacterial adaption to nanomaterials, it is critical to explore the main mechanism behind the adaptive morphogenesis of microorganisms. In this work, the biofilms formed from activated sludge exposed to 5 and 50 mg/L nTiO₂ in the dark had increased biomass and selectively enriched pathogens. To further elaborate adaptive mechanism of biofilm formation induced by nTiO₂, the protein response and protein phosphorylation modification of Escherichia coli K12 were determined using integrative systems biology analyses of proteomics and phosphoproteomics. Results identified that E. coli cultivated with nTiO₂ considerably upregulated iron acquisition, and regulated protein phosphorylation states associated with of transcription and translation and biofilm formation relative to unexposed controls. Accordingly, bacteria increased siderophores and exopolysaccharide content (increased by about 57% and 231%, respectively), and enhanced resistance to transcriptional inhibitory antibiotics. Moreover, a dose of an iron chelator, i.e., deferoxamine mesylate salt, effectively retarded the biofilm development of bacteria exposed to 50 mg/L nTiO₂. Overall, this work will provide a new insight for biofouling control, and contribute to an improved understanding of microbial adaption to nanomaterials.

Microbially-derived cocktail of carbohydrases as an anti-biofouling agents: a 'green approach'

Enzymes, also known as biocatalysts, display vital properties like high substrate specificity, an eco-friendly nature, low energy inputs, and cost-effectiveness. Among their numerous known applications, enzymes that can target biofilms or their components are increasingly being investigated for their anti-biofouling action, particularly in healthcare, food manufacturing units and environmental applications. Enzymes can target biofilms at different levels like during the attachment of microorganisms, formation of exopolymeric substances (EPS), and their disruption thereafter. In this regard, a consortium of carbohydrases that can target heterogeneous polysaccharides present in the EPS matrix may provide an effective alternative to conventional chemical anti-biofouling methods. Further, for complete annihilation of biofilms, enzymes can be used alone or in conjunction with other antimicrobial agents. Enzymes hold the promise to replace the conventional methods with greener, more economical, and more efficient alternatives. The present article explores the potential and future perspectives of using carbohydrases as effective anti-biofilm agents.

Variations in microbial community on different materials in Sanya Marine Environment Experimental Station, China

Marine biofouling occurs through the colonization of undesired microorganisms on the surfaces of structures. In this study, four immersion cycles (2, 5, 15, and 25 days) of total immersion in seawater were carried out at the Sanya Marine Environmental Test Station using three materials: industrial pure titanium (Ti), hot-dip zinc (Zn), and glass slide (GS). Three phyla, four classes, and nine bacterial genera were identified. The dominant genera were Pseudomonas, Alteromonas, and Pseudoalteromonas. The number of bacteria increased with soaking time. Sixty-one species of diatoms belonging to 30 genera, 24 families, and 16 orders were detected, among which the dominant genera were Amphora, Nitzschia, and Navicula. Four genera of ciliates belonged to two classes, three orders, and four families, among which the dominant species were Euplotes sp. and Uronema marinum. Tubular polychaetes was the dominant metazoans. Species diversity increased over time. The highest biofilm diversity was observed on the GS surface. The diversity of biofilms on the Ti surface was higher than that on the Zn surface. This study provides basic data for marine material research, marine corrosion, and national defence construction.

Advancing Strategies of Biofouling Control in Water-Treated Polymeric Membranes

Polymeric membranes, such as polyamide thin film composite membranes, have gained increasing popularity in wastewater treatment, seawater desalination, as well as the purification and concentration of chemicals for their high salt-rejection and water flux properties. Membrane biofouling originates from the attachment or deposition of organic macromolecules/microorganisms and leads to an increased operating pressure and shortened service life and has greatly limited the application of polymeric membranes. Over the past few years, numerous strategies and materials were developed with the aim to control membrane biofouling. In this review, the formation process, influence factors, and consequences of membrane biofouling are systematically summarized. Additionally, the specific strategies for mitigating membrane biofouling including anchoring of hydrophilic monomers, the incorporation of inorganic antimicrobial nanoparticles, coating/grafting of cationic bactericidal polymers, and the design of multifunctional material integrated multiple anti-biofouling mechanisms, are highlighted. Finally, perspectives on the challenges and opportunities in anti-biofouling polymeric membranes are shared, shedding light on the development of even better anti-biofouling materials in near future.

Combined utilization of metabolic inhibitors to prevent synergistic multi-species biofilm formation

Biofilm is ubiquitous in industrial water systems, causing biofouling and leading to heat transfer efficiency decreases. In particular, multi-species living in biofilms could boost biomass production and enhance treatment resistance. In this study, a total of 37 bacterial strains were isolated from a cooling tower biofilm where acetic acid and propionic acid were detected as the main carbon sources. These isolates mainly belonged to Proteobacteria and Firmicutes, which occupied more than 80% of the total strains according to the 16S rRNA gene amplicon sequencing. Four species (Acinetobacter sp. CTS3, Corynebacterium sp. CTS5, Providencia sp. CTS12, and Pseudomonas sp. CTS17) were observed co-existing in the synthetic medium. Quantitative comparison of biofilm biomass from mono- and multi-species showed a synergistic effect towards biofilm formation among these four species. Three metabolic inhibitors (sulfathiazole, 3-bromopyruvic acid, and 3-nitropropionic acid) were employed to prevent biofilm formation based on their inhibitory effect on corresponding metabolic pathways. All of them displayed evident inhibition profiles to biofilm formation. Notably, combining these three inhibitors possessed a remarkable ability to block the multi-species biofilm development with lower concentrations, suggesting an enhanced effect appeared in simultaneous use. This study demonstrates that combined utilization of metabolic inhibitors is an alternative strategy to prevent multi-species biofilm formation.

37 bacterial strains were isolated and identified from a cooling tower biofilm.

Synergistic effect of biofilm formation was observed among four species.

Three metabolic inhibitors showed effective inhibition against biofilm formation.

Targeting cellular metabolism is an effective way to inhibit biofilm formation.

Enhancement of membrane fouling mitigation and trace organic compounds removal by electric field in a microfiltration reactor treating secondary effluent of a municipal wastewater treatment plant

Applying an electric field in the membrane filtration was an effective method to alleviate membrane fouling and enhance the trace organic compounds (TrOCs) removal. The secondary effluent of a municipal wastewater treatment plant was used as feed water to evaluate the performance of the electric field coupled microfiltration system. Applying a 1.25 V voltage reduced 22.9% membrane fouling by electrophoretic force, and the membrane fouling was alleviated by 70.8% at 3 V by electrochemical oxidation and electric field force. At 3 V, active chlorine and hydroperoxide generated on the electrodes and the acidic environment formed around the anode significantly inhibited the growth of microorganisms and their attachment on the membrane surface, and thus reduced the membrane fouling formed by microorganisms. Electrochemical oxidation also removed the protein in wastewater and changed the main organic components of membrane fouling from microorganisms, protein, and polysaccharide to humic substances and polysaccharide. Furthermore, the electrophoretic force and acidic environment reduced the electrostatic repulsion of humic substances and made them tend to aggregate and form hydrophilic porous fouling structures, which obviously lowered filtration resistance and showed significant membrane fouling mitigation. Also, the electric field effectively enhanced the removal of target TrOCs through electrochemical oxidation and electric field force improving the elimination of TrOCs from 8.5% ~ 26.1% at 0 V to 35.9% ~ 84.8% at 3 V.

Targeting membrane fouling with low dose oxidant in drinking water treatment: Beneficial effect and biological mechanism

Membrane fouling is the principal factor that currently limits the performance of gravity-driven membrane (GDM) filtration systems in drinking water treatment. In this study, the benefits of applying a low dose (approximately 0.1 mg·L-1) of environmentally benign oxidants, both H2O2 and KMnO4, as a pretreatment to GDM filtration system has been evaluated in terms of reduced membrane fouling and treated water quality. While both oxidants improved permeate flux, the effect of KMnO4 was greater than H2O2. Both oxidants reduced the size of influent organic substances and those of large molecular weight (>20 kDa), such as biopolymers, disappeared. The thickness of the fouling layers was substantially reduced after oxidation, and the KMnO4 system had a markedly different physical structure of fouling layer, with an apparent sub-layer of δ-MnO2 nanosheets below a fouling sub-layer. The formation of the δ-MnO2 nanosheets sub-layer appeared to protect the underlying membrane pores from contamination by influent organics. Oxidation pretreatment reduced the presence of proteins and polysaccharides in the fouling layers and significantly altered the bacterial community structures (p < 0.01) and decreased biodiversity. The microbial species that secreted amounts of extracellular polymeric substances (EPS), such as Xanthobacter, were not eliminated in the H2O2 fouling layer, while for the KMnO4 system, the manganese oxidizing bacteria (MOB; e.g., Pseudoxanthomonas) and metal-resistant genus Acidovorax, dominated the community.

Rheological characterisation of alginate-like exopolymer gels crosslinked with calcium

Bacterial alginate-like exopolymers (ALE) gels have been used in this work as a model for the extracellular polymeric matrix of biofilms. Aim was to relate the mechanical properties and strength of this matrix that make biofilms as persistent to cleaning as they are, to the complex cohesive molecular interactions involved. Mechanical properties of the gels as a function of CaCO₃ concentration were investigated using dynamic and static rheology. Gels with relatively low CaCO₃ concentrations, between 100 μmol and 300 μmol per g ALE, were found to exhibit similar viscoelastic behaviour as real biofilms, with elastic moduli between 50 Pa and 100 Pa and dissipation factors between 0.2 and 0.3. Increasing CaCO₃ concentrations resulted in an increase of the elastic modulus up to 250 Pa, accompanied by an increase in brittleness. At a CaCO₃ concentration of 1250 μmol per g ALE this trend stopped, probably due to disturbance of the continuous ALE network by precipitation of salts. Therefore, overdosing of Ca salts can be an adequate approach for the removal of biofouling. All gels exhibited permanent strain hardening under medium strain, and their mechanical properties showed dependency on their strain history. Even after application of an oscillatory strain with 200% amplitude that caused the gel structure to collapse, the gels recovered 65 to 90% of their original shear modulus, for the major part within the first 20 s. Recovery was slightly less for gels with high CaCO₃ concentration. In creep tests fitted with a Burgers model with multiple Kelvin elements at least three different interactions in the ALE gels could be distinguished with characteristic retardation times in the range of 10, 100 and 1000 s. Further identification of the mechanisms underlying the gel mechanics will allow the development of targeted strategies to undermine the mechanical strength of biofouling and aid the cleaning process.

Periodic chemical cleaning with urea: disintegration of biofilms and reduction of key biofilm-forming bacteria from reverse osmosis membranes

Biofouling is one of the major factors causing decline in membrane performance in reverse osmosis (RO) plants, and perhaps the biggest hurdle of membrane technology. Chemical cleaning is periodically carried out at RO membrane installations aiming to restore membrane performance. Typical cleaning agents used in the water treatment industry include sodium hydroxide (NaOH) and hydrochloric acid (HCl) in sequence. Rapid biofilm regrowth and related membrane performance decline after conventional chemical cleaning is a routinely observed phenomenon due to the inefficient removal of biomass from membrane modules. Since extracellular polymeric substances (EPS) make up the strongest and predominant structural framework of biofilms, disintegration of the EPS matrix should be the main target for enhanced biomass removal. Previously, we demonstrated at lab-scale the use of concentrated urea as a chemical cleaning agent for RO membrane systems. The protein denaturation property of urea was exploited to solubilize the proteinaceous foulants, weakening the EPS layer, resulting in enhanced biomass solubilization and removal from RO membrane systems. In this work, we investigated the impact of repeated chemical cleaning cycles with urea/HCl as well as NaOH/HCl on biomass removal and the potential adaptation of the biofilm microbial community. Chemical cleaning with urea/HCl was consistently more effective than NaOH/HCl cleaning over 6 cleaning and regrowth cycles. At the end of the 6 cleaning cycles, the percent reduction was 35% and 41% in feed channel pressure drop, 50% and 70% in total organic carbon, 30% and 40% in EPS proteins, and 40% and 66% in the peak intensities of protein-like matter, after NaOH/HCl cleaning and Urea/HCl cleaning, respectively. 16S ribosomal RNA (rRNA) gene sequencing of the biofilm microbial community revealed that urea cleaning does not select for key biofouling families such as Sphingomonadaceae and Xanthomonadaceae that are known to survive conventional chemical cleaning and produce adhesive EPS. This study reaffirmed that urea possesses all the desirable properties of a chemical cleaning agent, i.e., it dissolves the existing fouling layer, delays fresh fouling accumulation by inhibiting the production of a more viscous EPS, does not cause damage to the membranes, is chemically stable, and environmentally friendly as it can be recycled for cleaning.