A Fe3O4@Nico@Ag nanocatalyst for the hydrogenation of nitroaromatics

Synergistic effect of silver NPs immobilized on Fe3O4@L-proline magnetic nanocomposite toward the photocatalytic degradation of Victoria blue and reduction of organic pollutants

The surface of magnetite (Fe₃O₄) nanoparticles was subject to modification through the incorporation of L-proline (LP) by simple co-precipitation method in which silver nanoparticles were deposited by in situ method, thereby yielding the Fe₃O₄@LP-Ag nanocatalyst. The fabricated nanocatalyst was characterized using an array of techniques including Fourier-transform infrared (FTIR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometry (VSM), Brunauer-Emmett-Teller (BET), and UV-Vis spectroscopy. The results evince that the immobilization of LP on the Fe₃O₄ magnetic support facilitated the dispersion and stabilization of Ag NPs. The SPION@LP-Ag nanophotocatalyst exhibited exceptional catalytic efficiency facilitating the reduction of MO, MB, p-NP, p-NA, NB, and CR in the presence of NaBH₄. The rate constants obtained from the pseudo-first-order equation were 0.78, 0.41, 0.34, 0.27, 0.45, 0.44, and 0.34 min^-1 for CR, p-NP, NB, MB, MO, and p-NA, respectively. Additionally, the Langmuir-Hinshelwood model was deemed the most probable mechanism for catalytic reduction. The novelty of this study lies in the use of L-proline immobilized on Fe₃O₄ MNPs as a stabilizing agent for the in-situ deposition of silver nanoparticles, resulting in the synthesis of Fe₃O₄@LP-Ag nanocatalyst. This nanocatalyst exhibits high catalytic efficacy for the reduction of multiple organic pollutants and azo dyes, which can be attributed to the synergistic effects between the magnetic support and the catalytic activity of the silver nanoparticles. The easy recyclability and low cost of the Fe₃O₄@LP-Ag nanocatalyst further enhance its potential application in environmental remediation.

Palladium Nanoparticles on Chitosan-Coated Superparamagnetic Manganese Ferrite: A Biocompatible Heterogeneous Catalyst for Nitroarene Reduction and Allyl Carbamate Deprotection

Although metallic nanocatalysts such as palladium nanoparticles (Pd NPs) are known to possess higher catalytic activity due to their large surface-to-volume ratio, however, in nanosize greatly reducing their activity due to aggregation. To overcome this challenge, superparamagnetic chitosan-coated manganese ferrite was successfully prepared and used as a support for the immobilization of palladium nanoparticles to overcome the above-mentioned challenge. The Pd-Chit@MnFe₂O₄ catalyst exhibited high catalytic activity in 4-nitrophenol and 4-nitroaniline reductions, with respective turnover frequencies of 357.1 min^-1 and 571.4 min^-1, respectively. The catalyst can also be recovered easily by magnetic separation after each reaction. Additionally, the Pd-Chit@MnFe₂O₄ catalyst performed well in the reductive deprotection of allyl carbamate. Coating the catalyst with chitosan reduced the Pd leaching and its cytotoxicity. Therefore, the catalytic activity of Pd-Chit@MnFe₂O₄ was proven to be unrestricted in biology conditions.

Development of highly efficient magnetically recyclable Cu2+/Cu0 nano-photocatalyst and its enhanced catalytic performance for the degradation of organic contaminations

This work reports the successful functionalization of l-proline on the surface of superparamagnetic iron oxide nanoparticles (SPION) synthesized via a simple, cost-effective hydrothermal method. Moreover, the chemical attachment of Cu²⁺/Cu⁰ nanoparticles on the surface of SPION@l-proline was done by an in-situ deposition method. The developed nano-photocatalyst was characterized in detail by XRD, FT-IR, XPS, FE-SEM, TEM, EDX, BET, TGA, and VSM. XRD of SPION@l-proline-Cu reveals peaks of both SPION and copper nanoparticles which confirms the formation of nanophotocatalyst. TGA demonstrates a major weight loss between 250 and 310 °C due to l-proline which ensures the successful immobilization of SPION on the surface of l-proline. The band energy at 932 eV suggests a complete reduction of Cu²⁺ ion to Cu⁰ metal on the surface of SPION@l-proline nanocomposite as confirmed by the XPS technique. Under UV light irradiation, the photocatalytic reduction performance of the developed Cu²⁺ metal ion-based and Cu⁰ nanoparticle-based magnetic nano-photocatalysts was demonstrated and compared for the first time for the photocatalytic reduction of 4-NP, 4-NA, NB, MO, MB, and CR. The results show that Cu⁰-based magnetic nanophotocatalyst has slightly enhanced catalytic activity. Furthermore, solar-driven photocatalytic degradation of CR azo dye by synthesized nano-photocatalyst was also investigated, with a 95 % degradation efficiency in just 40 min. The developed magnetic nano-photocatalyst can easily be separated by using an external magnet due to the superparamagnetic nature of core material (SPION) at room temperature as confirmed from VSM and can be reused for multiple cycles without losing considerable catalytic activity. Because of its high photocatalytic efficiency, cost-effectiveness, good magnetic separation performance, non-toxicity, and strong thermal and chemical stabilities, Cu²⁺/Cu⁰-based magnetic nano-photocatalyst has potential application in wastewater treatment.

Novel insight on ferric ions addition to mitigate recalcitrant formation during thermal-alkali hydrolysis to enhance biomethanation

Thermal-chemical pre-treatment has proven to facilitate the solubilization of organics and improvement in biogas generation from the organic fraction of municipal solid waste (OFMSW). However, the production of recalcitrant is inevitable when OFMSW is pretreated at high temperatures and alkali dosage. This study develops a strategy to use Fe³⁺ to reduce the formation of recalcitrant compounds, i.e., 5-HydroxyMethyl Furfural (5-HMF), furfurals, and humic acids (HA) during thermal-alkali pre-treatment. It was postulated that the formation of the recalcitrant compound during pre-treatment can be reduced by Fe³⁺ dosing to oxidize intermediates of Maillard reactions. A decrease in 5-HMF (45-49%) and furfurals (54-66%) was observed during Fe³⁺ (optimum dose: 10 mg/L) mediated thermal-alkali pre-treatment owing to the Lewis acid behavior of FeCl₃. The Fe³⁺ mediated assays show a substantial improvement in VS removal (28%) and biogas yield, i.e., 31% (292 mL/gVS_added) in 150 °C + 3 g/L NaOH, 34% (316 mL/gVS_added) in 175 °C + 3 g/L NaOH, and 36% (205 mL/gVS_added) in 200 °C + 3 g/L NaOH assays, over their respective controls (no Fe³⁺ dosing). The reducing property of Fe³⁺ rendered a low ORP (-345 mV) in the system than control, which is beneficial to the anaerobic microbiome. Electrical conductivity (EC) also shows a three-fold increase in Fe³⁺ mediated assays over control, promoting direct interspecies electron transfer (DIET) amongst microbes involved in the electrical syntrophy. The score plot and loading plots from principal component analysis (PCA) showed that the results obtained by supplementing 10 mg/L Fe³⁺ at 150, 175, and 200 °C were significantly different. The correlation of the operational parameters was also mutually correlated. This work provides a techno-economically and environmentally feasible option to mitigate the formation of recalcitrant compounds and enhance biogas production in downstream AD by improving the degradability of pretreated substrate.

Plasticized magnetic starch-based Fe3O4 clay polymer nanocomposites for phosphate adsorption from aqueous solution

Plastics contribute a magnificent role to modern civilization, but the waste becomes a huge burden to ecology and remains intact for a thousand years. Hence, the recent movement is shifted to biodegradable plastic. In this study, an attempt was made to introduce an added value to the environment where the bio-plasticized materials were used for phosphate removal. A G-plasticized magnetic starch-based Fe₃O₄ clay polymer nanocomposite (PNC) was synthesized to remove phosphate from the aqueous solution. It was synthesized from activated carbon (AC), coated iron oxide nanoparticles (CIONP), nanoclay (NC), and glycerol (G) as a plasticizer. The synthesized adsorbents were characterized with UV-Vis, SEM, XRD, and FTIR. The PNC and constituent (CIONP) were tested for phosphate removal through batch adsorption experiments. The adsorption capacity increases with increasing the adsorbent dose and decreases with an increase in phosphate concentration. The synthesized PNC effectively raised the constituent optimum phosphate ion adsorption pH from acidic (pH = 3) to slightly acidic (pH = 6). At the optimal pH, the CIONP and PNC maximum phosphate adsorption capacity (MPAC) was 3.12 and 2.31 mg P/g, respectively. In addition, the phosphate removal efficiency of PNC (45-95% at pH 6) was comparable to CIONP (58-97% at pH 3) under an initial 2–100 mg P/L. The adsorbents adsorption kinetics and isotherm study best described by the pseudo-second-order and Freundlich model, in turn. The SEM images support the conclusion, in which the PNC shows a heterogenous porous surface. Therefore, the adsorption mechanisms were mainly described by multilayer and chemical adsorption, such as electrostatic and ion exchange. It can be concluded that there is a positive synergistic effect between the biopolymer (starch) and nanomaterials that form the PNC. This study results propose the multiple added values of modified bio-plasticized material (with adsorbent) for environmental (phosphate) remediation.

Ultrafine NiMoOx nanoparticles confined in mesoporous carbon for the reduction of nitroarenes: effect of the composition and accessibility of the active sites

The design of ultrafine NiMoO_x nanoparticles (NPs) confined in hierarchically porous carbon remains a great challenge due to its high calcination temperature. In addition, the composition of active sites of NiMoO_x NPs for the hydrogenation reaction is still ambiguous. Herein, we report a general approach for the synthesis of ultrafine NiMoO_x NPs confined in mesoporous carbon with different morphologies and compositions using the replication method with SBA-15 as a hard template. The pore structure of mesoporous carbon and the Ni/Mo composition valence-state were discovered to be the main factors in the reduction of nitroarenes. The NiMoO_x/mesoporous carbon-platelet (NiMoO_x/MC-PL) with short mesochannels (∼350 nm) and high surface area (∼995 m² g⁻¹) possessed excellent catalytic activity towards the reduction of 4-nitrophenol, whereas NiMoO_x/mesoporous carbon-hexagonal-prism (NiMoO_x/MC-HP), NiMoO_x/mesoporous carbon-long-rod (NiMoO_x/MC-LR), and NiMoO_x/mesoporous carbon-spherical (NiMoO_x/MC-SP) with long mesochannels and relatively less surface area exhibited poor catalytic performance. The bifunctional mechanism or electronic synergistic effects of Ni and Mo species enhanced their catalytic performance. A good balance between MoO_x and metallic Ni (NiMoO_x/MC-PL-450) was found to be suitable for the reduction of 4-NP.

Ultrafine NiMoO_x NPs were confined in the framework of mesoporous carbon by using the replication method for the reduction of nitroarenes.

An overview of recent progress on noble metal modified magnetic Fe3O4 for photocatalytic pollutant degradation and H2 evolution

Noble metal modified magnetic Fe₃O₄ catalysts for photocatalytic pollutant degradation and H₂ evolution are reviewed.

Silver-nanospheres as a green catalyst for the decontamination of hazardous pollutants

This paper reports the facile, green and one-pot synthesis of silver-nanospheres (Ag-NSs) and their use as an excellent green catalyst for the decontamination of hazardous pollutants.