Determination of Bismuth by Dielectric Barrier Discharge Atomic Absorption Spectrometry Coupled with Hydride Generation: Method Optimization and Evaluation of Analytical Performance

A probe of new molecularly imprinted solid-phase extraction coupled with HPLC-DAD and atomic absorption spectrophotometry for quantification of tetracycline HCl, metronidazole and bismuth subcitrate in combination with their official impurities: Application in dosage form and human plasma

The integration of molecular imprinting technique with chromatographic one has a great impact on the assay's selectivity and sensitivity. Herein, a molecularly imprinted solid-phase extraction associated with high performance liquid chromatography (MISPE-HPLC) was employed for simultaneous determination of the co-formulated drugs; tetracycline hydrochloride (TET) and metronidazole (MET), in plasma and in their anti-H-pylori drug for the first time. Two sorts of molecularly imprinted polymers (MIPs) were fabricated using TET and MET as the template molecules, while ethylene glycol dimethacrylate and methacrylic acid were used as a cross-linker and a monomer, respectively. The synthesized MIPs were identified using different techniques. The adsorption-desorption capability of each template was investigated towards its corresponding MIP. The extraction conditions of MISPE was optimized with respect to TET/MIP and MET/MIP sorbent. Bismuth subcitrate (BSC), the third co-formulated drug was analyzed in spiked human plasma using an atomic absorption spectrometric (AAS) method. The performance of the developed methods was assured as per ICH guidelines for analyzing the studied drugs in their pharmaceutical dosage form along with two of their official impurities. In addition, bioanalytical method validation was conducted where linearity was achieved at 2.0-40.0 μg mL-1, 2.0-40.0 μg mL-1 and 5.0-80.0 μg mL-1 for TET, MET and BSC, respectively.

Rapid detection of ultratrace urinary arsenic by direct sampling microplasma vaporization based on silicon nitride

At present, immediate monitoring urinary arsenic is still a challenge for treating arsenic poisoning patients. Thus, a fast, reliable and accurate analytical approach is indispensable to monitor ultratrace arsenic in urine sample for health warning. In this work, a silicon nitride (SN) rod was first integrally utilized as a sample carrier for ≤50 μL urinary aliquot, an electric heater for removing water and ashing sample as well as a high voltage electrode for dielectric barrier discharge vaporization (DBDV). The direct analytical method of arsenic in urine without sample digestion was thus developed using atomic fluorescence spectrometer (AFS) as a model detector. After 4 V electrically heating the SN rod for 60 s, urine sample was dehydrated and ashed outside; then, DBD was exerted under 0.8 A with 0.8 L/min H₂ + Ar (1:9, v:v) for 20 s to vaporize arsenic analyte from the SN rod. After optimization, 0.014 μg/L arsenic detection limit (LOD) was reached with favorable analytical precision (RSD <5%) and accuracy (91-110% recoveries) for real sample analysis. As a result, the whole analysis process only consumes <3 min to exclude complicated sample preparation; furthermore, the designed DBDV system only occupies 25 W and <2 kg, which renders a miniature sampling component to hyphenate with a miniature detector to detect arsenic. Thus, this direct sampling DBDV method extremely fulfills the fast, sensitive and precise detection of ultratrace arsenic in urine sample.

Atomization of As and Se volatile species in a dielectric barrier discharge atomizer after hydride generation: Fate of analyte studied by selected ion flow tube mass spectrometry

Atomization of hydrides and their methylated analogues in a dielectric barrier discharge (DBD) plasma atomizer was investigated. Selected ion flow tube mass spectrometry (SIFT-MS) was chosen as a detector being capable of selective detection of non-atomized original volatile species allowing thus direct quantification of atomization efficiency. Selenium hydride (SeH₂) and three volatile arsenic species, namely arsenic hydride (AsH₃), monomethylarsane (CH₃AsH₂) and dimethylarsane ((CH₃)₂AsH), were selected as model analytes. The mechanistic study performed contributes to understanding of the atomization processes in atomic absorption spectrometry (AAS). The presented results are compatible with a complete atomization of arsenic hydride as well as its methylated analogues and with atomization efficiency of SeH₂ below 80%. Using AsH₃ as a model analyte and a combination of AAS and SIFT-MS detectors has revealed that the hydride is not atomized, but decomposed in the DBD atomizer in absence of hydrogen fraction in the carrier gas. Apart from investigation of analyte atomization, the SIFT-MS detector is capable of quantitative determination of water vapor content being either transported to, or produced in the atomizer. This information is crucial especially in the case of the low-power/temperature DBD atomizer since its performance is sensitive to the amount of water vapor introduced into the plasma.

Flow injection hydride generation and on-line W-coil trapping for electrothermal vaporization dielectric barrier discharge atomic emission spectrometric determination of trace cadmium

A fast, low-cost and sensitive method for the determination of trace cadmium was developed by using a miniaturized dielectric barrier discharge microplasma atomic emission spectrometer coupled with a tungsten coil (W-coil) for on-line hydride generation trapping-electrothermal vaporization. Total sample throughput can be greatly improved through the adoption of a horizontally fixed W-coil and the flow injection mode. In addition, the horizontally fixed W-coil and an inserted quartz capillary for on-line trapping contributed to stable and good signal even at a high gas flow rate when volatile cadmium species were trapped, and less sample-consuming and time-saving can be realized in this work. Compared to direct injection, the sensitivity and the LOD were improved by 29- and 38-fold, respectively. The proposed method provides a promising approach to develop a miniaturized instrumentation for highly sensitive detection of trace elements.

Fast and High Sensitive Analysis of Lead in Human Blood by Direct Sampling Hydride Generation Coupled with in situ Dielectric Barrier Discharge Trap

A direct sampling hydride generation (HG) system based on modified gas liquid separator (GLS) coupled with in situ dielectric barrier discharge (DBD) is first rendered to detect lead in blood samples. Herein, a triple-layer coaxial quartz tube was employed as DBD trap (DBDT) to replace the original atomizer of atomic fluorescence spectrometry (AFS) to satisfy the in situ preconcentration. After 40-fold dilution, foams generated from protein in a blood sample can be eliminated via the double-GLS set; and lead in a blood sample were generated as plumbane under 3.5% HNO₃ (v:v) and 30 g/L NaOH with 8 g/L KBH₄, 10 g/L H₃BO₃, and 5 g/L K₃[Fe(CN)₆]. Then, lead analyte was trapped on the DBD quartz surface by 9 kV discharging at 50 mL/min air; and subsequently released by 12 kV discharging at 110 mL/min H₂. The absolute detection limit (LOD) for Pb was 8 pg (injection volume = 2 mL), and the linearity (R² > 0.997) range was 0.05 - 50 μg/L. The results were in good agreement with that of blood certified reference materials (CRM), and spiked recoveries for real blood samples were 95 - 104% within a relative standard deviation of 5% (RSD). Via gas phase enrichment, the established method improved analytical sensitivity (peak height) by 8 times. The entire analysis time including blood sample preparation can be kept to within 10 min. The combination of modified GLS and DBDT can facilitate the quickness, accuracy, and sensitivity, revealing a promising future for monitoring lead in blood to protect humans, especially children's health.

In situ preconcentration of lead by dielectric barrier discharge and its application to high sensitivity surface water analysis

A novel dielectric barrier discharge (DBD) reactor was utilized to in situ enrich and atomize lead in gas phase. The structure of DBD reactor was optimized to broaden the acidity window of plumbane generation from 1% to 3.5%, bringing better analytical stability and practicability deriving from hydride generation process. For the first time DBD proved effective in lead preconcentration and broadening the acidity window of plumbane generation. Pb can be trapped quantitatively (~100%) on the quartz surface of DBD tube under O₂-containing atmosphere and released (~100%) under H₂-containing atmosphere. The absolute detection limit (LOD) for Pb was 4.1 pg (injection volume = 1.2 mL), and the linear (R² > 0.999) range was 0.05-100 μg/L. The results were in good agreement with those of certified reference materials (CRMs), and spiked recoveries for surface water samples were 99-104% with 2-8% RSD. By gas phase analyte enrichment, the proposed method reduced absolute LOD by 10 times. It was deduced that plumbane was changed to lead oxide species trapped on the quartz tube surface and then released, and transported in form of atoms to the detection zone.

A portable and field optical emission spectrometry coupled with microplasma trap for high sensitivity analysis of arsenic and antimony simultaneously

In this work, a portable and reliable optical emission spectrometric (OES) instrument based on solid acid hydride generation (HG) and subsequent in situ dielectric barrier discharge (DBD) preconcentration was first developed for simultaneous and field analysis of ultratrace As and Sb in environmental water. In situ DBD fulfilled both gas phase enrichment (GPE) and excitation; effective enrichment made it possible to use a low-cost charge coupled device (CCD) as detector. To simplify field protocol, solid tablet made from sulfamic acid was first used to replace hydrochloric acid for co-generation of As and Sb hydrides. Moisture interference was eliminated by carrier gas sweeping without any desiccant. After calculating peak volume for emission data handling, detection limits (LODs) were 0.5 μg L^-1 for As and 0.2 μg L^-1 for Sb, respectively, with <3% relative standard deviations (RSDs) at 10 μg L^-1; linear dynamic ranges (R²>0.995) were 2-200 μg L^-1 for As and 1-200 μg L^-1 for Sb, respectively. The results agreed with certified values of CRMs and recoveries were 87-97% vs. inductively coupled plasma mass spectrometry. The running costs can be controlled within one dollar per use. This HG-in situ DBD trap-OES scheme, with demonstrated advantages in sensitivity, low-cost, power (<60 W), size (0.6 m × 0.5 m × 0.3 m), weight (15 kg), gas consumption (300 measurements per 4 L tank), and multi-element capability, was implemented in a miniature spectrometer for field analysis.

Two water-soluble fluorescence probes based on 5(6)-carboxyl rhodamine for Cu2+ imaging in living cells

Two novel water-soluble fluorescence probes T1 and T2 based on 5(6)-carboxyl rhodamine were designed and synthesized using a regioselective reaction. The probes exhibited highly selective and sensitive recognition toward Cu²⁺ over other metal ions in acetonitrile/Tris-HCl buffer solution (2:98, v/v; pH 7.4). Detection limits were 0.4 μM for T1 and 4.50 μM for T2 based on fluorescence titration analysis. Furthermore, probe T1 was successfully applied in cell imaging experiments to monitor Cu²⁺ in cells.

Deducing rotational quantum-state distributions from overlapping molecular spectra

A novel method for fast and robust calculation of Boltzmann plots from molecular spectra is presented. Its use is demonstrated on the OH(A-X) spectrum near 310 nm. A limitation of the method is identified: for overlapping spectra of the OH(A-X) and N₂(C-B, Δv = 1) band sequence, the calculation may often fail due to insufficient number of measured points. This is solved by introducing experimentally determined bounds for the N₂(C) rotational distribution. Three cases are presented: (i) with undisturbed OH(A-X) emission, (ii) with strong emission of N₂(C-B) in the said spectral range, and (iii) with weak but not negligible nitrogen emission. In case (ii), the data in the spectral range 306-320 nm are sufficient for the analysis. In case (iii), information from another spectral range with undisturbed N₂(C-B) emission is necessary. These illustrate all relevant cases often encountered in laboratory plasmas. The calculated Boltzmann plots are not further analyzed in this article but can be used for development and validation of kinetic models with rotational resolution. The implementation of the reported method using the massiveOES software package written in the Python language is available in the supplementary material.

Enhanced Photochemical Vapor Generation for the Determination of Bismuth by Inductively Coupled Plasma Mass Spectrometry

An enhanced photochemical vapor generation (PVG) sample introduction procedure is developed for the determination of trace Bi with inductively coupled plasma mass spectrometry (ICP MS) by the addition of iron. Gas chromatography mass spectrometry (GC-MS) reveals that (CH₃)₃Bi is the major component of the volatile Bi species formed in the presence of 20% (v/v) acetic acid, 5% (v/v) formic acid, and 60 μg mL^-1 Fe³⁺ under UV irradiation. The addition of Fe³⁺ not only largely increases the PVG efficiency of Bi³⁺ but also accelerates the reaction kinetics of photochemical reduction of Bi³⁺. The analytical sensitivity was enhanced 30-fold using PVG for sample introduction compared to that for direct solution nebulization detection by ICP MS detection. Furthermore, the proposed method shows much better tolerance of interference from Cu²⁺ and Ni²⁺ than that from conventional hydride generation (HG). Under the optimized conditions, a detection limit of 0.3 ng L^-1 was obtained for Bi by ICP MS determination. The relative standard deviation (RSD) was 2.5% for seven replicate measurements of 0.5 ng mL^-1 Bi³⁺ standard solution. The proposed method has been successfully applied for the determination of Bi in environmental samples, including water samples, and certified reference material of soil (GSS-1) and sediments (GSD-5a and GSD-10) with satisfying results.

Behavior of selenium hydride in heated quartz tube and dielectric barrier discharge atomizers

Atomization of SeH₂ in an externally heated multiple microflame quartz tube atomizer (MMQTA) as well as planar dielectric barrier discharge (DBD) atomizer was investigated using a variety of probes. Deposits of Se on inner surfaces of the atomizers were quantified and their distribution visualized by autoradiography with ⁷⁵Se radiotracer. The gas phase fraction of Se transported beyond the confines of the atomizers was also determined. In the MMQTA, a 15% mass fraction of Se was deposited in a narrow zone at both colder ends of the optical arm (100-400 °C). By contrast, a 25-40% mass fraction of Se was deposited homogeneously along the entire length of the optical arm of the DBD, depending on detection technique employed. The fraction of Se transported outside the MMQTA approached 90%, whereas it was 50-70% in the DBD. The presence of H₂ was essential for atomization of selenium hydride in both atomizers. The gaseous effluent arising from the hydride generator as well as the atomizers was investigated by direct analysis in real time (DART) coupled to an Orbitrap-mass spectrometer, enabling identification of major gas phase species of Se.

Diethyldithiocarbamate enhanced chemical generation of volatile palladium species, their characterization by AAS, ICP-MS, TEM and DART-MS and proposed mechanism of action

Comprehensive investigation of chemical generation of volatile species (VSG) of palladium for detection by analytical atomic and mass spectrometry and, specifically, the mechanistic aspects of their formation and tentative identification are presented. VSG was achieved in a flow injection mode using a generator that permitted rapid mixing of acidified sample with NaBH₄ reductant. Atomization in a diffusion flame with detection by atomic absorption spectrometry was exclusively used for optimization of generation conditions while inductively coupled plasma mass spectrometry was utilized to investigate overall system efficiency and analytical metrics of the VSG system for potential ultratrace analysis. Sodium diethyldithiocarbamate (DDTC) served as a crucial reaction modifier, enhancing overall system efficiency 9-fold. Combinations of modifiers, Triton X-100 and Antifoam B surfactants provided a synergistic effect to yield a further 2-fold enhancement of VSG. The overall system efficiency was in the range 16-22%, with higher efficiencies correlating with higher Pd concentrations. The contribution of co-generated aerosol to the overall system efficiency, determined by means of concurrent measurement of added Cs, was negligible - less than 0.1%. The nature of the volatile species was investigated using several approaches, but principally by transmission electron microscopy (TEM) after their collection on a grid, and by direct analysis in real time (DART) using high resolution orbitrap mass spectrometry. These experiments suggest a parallel but dual-route mechanism of VSG of Pd, one attributed to generation of a volatile DDTC chelate of Pd and a second to nanoparticle formation.

Atomization of Bismuthane in a Dielectric Barrier Discharge: A Mechanistic Study

Atomization of bismuthane in a planar dielectric barrier discharge (DBD) atomizer was investigated using a variety of probes, including atomic absorption spectrometry (AAS) to monitor distribution of free atoms along the optical path and direct analysis in real time (DART) coupled to an Orbitrap mass spectrometer to identify the structure of the species arising from the hydride generator as well as the atomizer. Results obtained with the DBD were compared to those from a conventional externally heated quartz tube atomizer (QTA). Free Bi atoms were essentially absent outside the central part of the DBD atomizer, suggesting their high reactivity. The gas phase analyte fraction transported beyond the confines of the DBD or QTA atomizers, quantified by inductively coupled plasma mass spectrometry (ICP-MS), was less than 10%. The amount of Bi found in acidic leachates of the interiors of both atomizers, representing the fraction retained on their surfaces, was ca. 90%. These complementary experiments comprising the determination of recovered Bi in the nitric acid leachates from deposition in the atomizer on the one hand and quantification of the Bi fraction transportable outside the atomizer on the other, were in excellent agreement, providing 100% mass balance of detected analyte. The high fraction of Bi deposited in the atomizers indicates significant reactivity of free Bi atoms, which is in accord with the fact that almost no free Bi atoms exist beyond the physical boundaries of the DBD. The extent of interference from other hydride forming elements (As, Sb, Se) on Bi response by AAS using DBD and QTA atomizers was investigated, with the former atomizer providing superior performance. Compared to QTA, DBD provided 2 orders of magnitude and 1 order of magnitude, respectively, better resistance to interference from Se and Sb.