Fluorophilic Ionophores for Potentiometric pH Determinations with Fluorous Membranes of Exceptional Selectivity

Fundamental investigation on fluorous nanoemulsion optodes: effect of matrix fluorination on selectivity

As fundamental investigation on fluorous nanoemulsion (NE) optodes for highly selective perfluorooctanesulfonate (PFOS-) sensing, the effect of matrix fluorination on selectivity was investigated. Due to the high hydrophobicity of PFOS- itself, it responded in exhaustive mode regardless of the fluorination ratio of the matrix, and the lowest detectable PFOS- concentration was on the order of 10-7 to 10-6 M. On the other hand, the response of non-fluorous interfering anions was suppressed as the fluorination ratio of the matrix increased. It was revealed that the relative selectivity of PFOS- for hydrophobic anions, ClO4-, SCN-, and 1-octanesulfonate (OS-) was improved by more than one order of magnitude, up to nearly two orders of magnitude, and that it was also improved by less than one order of magnitude for hydrophilic anions, Br-, Cl-, and SO4-, in logarithmic selectivity coefficient (log K PFOS - , j opt ).

Improvement of the Upper Detection Limit of Ionophore-Based H+-Selective Electrodes: Explanation and Elimination of Apparently Super-Nernstian Responses

The response range of an ion-selective electrode (ISE) has been described by counterion interference at the lower and Donnan failure at the upper detection limit. This approach fails when the potentiometric response at the upper detection limit exhibits an apparently super-Nernstian response, as has been reported repeatedly for H+-selective electrodes. While also observed when samples contain other anions, super-Nernstian responses at low pH are a problem in particular for samples that contain phthalate, a common component of commercial pH calibration solutions. This work shows that coextraction of H+ and a sample anion into the sensing membrane alone does not explain these super-Nernstian responses, even when membrane-internal diffusion potentials are taken into account. Instead, these super-Nernstian responses are explained by the formation of complexes between that anion and at least two protonated ionophore molecules. As demonstrated by experiments and explained with quantitative phase boundary models, the apparently super-Nernstian responses at low pH can be eliminated by restricting the molecular ratio of ionophore and ionic sites. Notably, this conclusion results in recommendations for the optimization of sensing membranes that, in some instances, will conflict with previously reported recommendations from the ionic site theory for the optimization of the lower detection limit. This mechanistic insight is key to maximizing the response range of these ionophore-based ISEs.

Ion-Selective Potentiometry with Plasma-Initiated Covalent Attachment of Sensing Membranes onto Inert Polymeric Substrates and Carbon Solid Contacts

The physical delamination of the sensing membrane from underlying electrode bodies and electron conductors limits sensor lifetimes and long-term monitoring with ion-selective electrodes (ISEs). To address this problem, we developed two plasma-initiated graft polymerization methods that attach ionophore-doped polymethacrylate sensing membranes covalently to high-surface-area carbons that serve as the conducting solid contact as well as to polypropylene, poly(ethylene-co-tetrafluoroethylene), and polyurethane as the inert polymeric electrode body materials. The first strategy consists of depositing the precursor solution for the preparation of the sensing membranes onto the platform substrates with the solid contact carbon, followed by exposure to an argon plasma, which results in surface-grafting of the in situ polymerized sensing membrane. Using the second strategy, the polymeric platform substrate is pretreated with argon plasma and subsequently exposed to ambient oxygen, forming hydroperoxide groups on the surface. Those functionalities are then used for the initiation of photoinitiated graft polymerization of the sensing membrane. Attenuated total reflection-Fourier transform infrared spectroscopy, water contact angle measurements, and delamination tests confirm the covalent attachment of the in situ polymerized sensing membranes onto the polymeric substrates. Using membrane precursor solutions comprising, in addition to decyl methacrylate and a cross-linker, also 2-(diisopropylamino)ethyl methacrylate as a covalently attachable H+ ionophore and tetrakis(pentafluorophenyl)borate as ionic sites, both plasma-based fabrication methods produced electrodes that responded to pH in a Nernstian fashion, with the high selectivity expected for ionophore-based ISEs.

Covalently attached ionophores extend the working range of potentiometric pH sensors with poly(decyl methacrylate) sensing membranes

The pH working range of solid-contact ion-selective electrodes (ISEs) with plasticizer-free poly(decyl methacrylate) sensing membranes is shown to be expanded by covalent attachment of H+ ionophores to the polymeric membrane matrix. In situ photopolymerization not only incorporates the ionophores into the polymer backbone, but at the same time also attaches the sensing membranes covalently to the underlying inert polymer and nanographite solid contact, minimizing sensor drift and preventing failure by membrane delamination. A new pyridine-based H+ ionophore, 3-(pyridine-3-yl)propyl methacrylate, has lower basicity than trialkylamine ionophores and expands the upper detection limit. This reduces in particular the interference from hydrogen phthalate, which is a common component of commercial pH buffers. Moreover, the lower detection limit is improved by replacing the CH2CH2 spacer of previously reported dialkylaminoethyl methacrylates with a (CH2)10 spacer, which increases its basicity. Notably, for the more basic and highly cation-selective ionophore 10-(diisopropylamino)decyl methacrylate, the extent of counterion interference from hydrogen phthalate shifted the upper detection limit to lower pH by nearly one pH unit when the crosslinker concentration was decreased.

FAST (Flexible Acetylcholine Sensing Thread): Real-Time Detection of Acetylcholine with a Flexible Solid-Contact Potentiometric Sensor

Acetylcholine (ACh) is involved in memory and learning and has implications in neurodegenerative diseases; it is therefore important to study the dynamics of ACh in the brain. This work creates a flexible solid-contact potentiometric sensor for in vitro and in vivo recording of ACh in the brain and tissue homogenate. We fabricate this sensor using a 250 μm diameter cotton yarn coated with a flexible conductive ink and an ACh sensing membrane that contains a calix[4]arene ionophore. The exposed ion-to-electron transducer was sealed with a 2.5 μm thick Parylene C coating to maintain the flexibility of the sensor. The resulting diameter of the flexible ACh sensing thread (FAST) was 400 μm. The FAST showed a linear response range from 1.0 μM to 10.0 mM in deionized water, with a near-Nernstian slope of 56.11 mV/decade and a limit of detection of 2.6 μM. In artificial cerebrospinal fluid, the limit of detection increased to 20 μM due to the background signal of ionic content of the cerebrospinal fluid. The FAST showed a signal stability of 226 μV/h over 24 h. We show that FAST can measure ACh dynamics in sheep brain tissue and sheep brain homogenate after ACh spiking. FAST is the first flexible electrochemical sensor for monitoring ACh dynamics in the brain.

An Accessible Yarn-Based Sensor for In-Field Detection of Succinylcholine Poisoning

Succinylcholine (SUX) is a clinical anesthetic that induces temporary paralysis and is degraded by endogenous enzymes within the body. In high doses and without respiratory support, it results in rapid and untraceable death by asphyxiation. A potentiometric thread-based method was developed for the in-field and rapid detection of SUX for forensic use. We fabricated the first solid-contact SUX ion-selective electrodes from cotton yarn, a carbon black ink, and a polymeric ion-selective membrane. The electrodes could selectively measure SUX in a linear range of 1 mM to 4.3 μM in urine, with a Nernstian slope of 27.6 mV/decade. Our compact and portable yarn-based SUX sensors achieved 94.1% recovery at low concentrations, demonstrating feasibility in real-world applications. While other challenges remain, the development of a thread-based ion-selective electrode for SUX detection shows that it is possible to detect this poison in urine and paves the way for other low-cost, rapid forensic diagnostic devices.

High-Performance pH Sensor Electrodes Based on a Hexagonal Pt Nanoparticle Array-Coated Nanoporous Alumina Membrane

Porous anodic alumina membranes coated with Pt nanoparticles (PAAM/Pt) have been employed as pH sensor electrodes for H⁺ ion detection. The PAAM was designed using a two-step anodization process. Pt nanoparticles were then sputtered onto the membrane at different deposition times. The membrane's morphological, chemical, and optical characteristics were carefully assessed following the fabrication stage using a variety of analytical techniques. The potential of the PAAM/Pt sensor electrode was investigated by measuring the potential using a simple potentiometric method. The effects of depositing Pt nanoparticles for 3-7 min on sensor electrode sensitivity were examined. The optimal potentiometric Nernstian response slope for the PAAM/Pt sensor electrode with 5 min Pt sputter coating is 56.31 mV/decade in the pH range of 3.0 to 10 at 293 K. Additionally, the PAAM/Pt sensor electrode's stability and selectivity in various ions solutions were examined. The sensor electrode had a lifetime of more than six weeks and was kept in a normal air environment.

Reliable environmental trace heavy metal analysis with potentiometric ion sensors - reality or a distant dream

Over two decades have passed since polymeric membrane ion-selective electrodes were found to exhibit sufficiently lower detection limits. This in turn brought a great promise to measure trace level concentrations of heavy metals using potentiometric ion sensors at environmental conditions. Despite great efforts, trace analysis of heavy metals using ion-selective electrodes at environmental conditions is still not commercially available. This work will predominantly concentrate on summarizing and evaluating prospects of using potentiometric ion sensors in view of environmental determination of heavy metals in on-site and on-line analysis modes. Challenges associated with development of reliable potentiometric sensors to be operational in environmental conditions will be discussed and reasoning behind unsuccessful efforts to develop potentiometric on-site and on-line environmental ion sensors will be explored. In short, it is now clear that solely lowering the detection limit of the ion-selective electrodes does not guarantee development of successful sensors that would meet the requirement of environmental matrices over long term usage. More pressing challenges of the properties and the performance of the potentiometric sensors must be addressed first before considering extending their sensitivity to low analyte concentrations. These are, in order of importance, selectivity of the ion-selective membrane to main ion followed by the membrane resistance to parallel processes, such as water ingress to the ISM, light sensitivity, change in temperature, presence of gasses in solution and pH and finally resistance of the ion-selective membrane to fouling. In the future, targeted on-site and on-line environmental sensors should be developed, addressing specific environmental conditions. Thus, ion-selective electrodes should be developed with the intention to be suitable to the operational environmental conditions, rather than looking at universal sensor design validated in the idealized and simple sample matrices.

A Bis-Acridinium Macrocycle as Multi-Responsive Receptor and Selective Phase-Transfer Agent of Perylene

A bis-acridinium cyclophane incorporating switchable acridinium moieties linked by a 3,5-dipyridylanisole spacer was studied as a multi-responsive host for polycyclic aromatic hydrocarbon guests. Complexation of perylene was shown to be the most effective and was characterized in particular by a charge-transfer band as signal output. Effective catch and release of the guest was triggered by both chemical (proton/hydroxide) and redox stimuli. Moreover, the dicationic host was also easily switched between organic and perfluorocarbon phases for applications related to the enrichment of perylene from a mixture of polycyclic aromatic hydrocarbons.

Fluorous-Phase Ion-Selective pH Electrodes: Electrode Body and Ionophore Optimization for Measurements in the Physiological pH Range

Because of their low polarity and polarizability, fluorous sensing membranes are both hydrophobic and lipophobic and exhibit very high ion selectivities. Here, we report on a new fluorous-membrane ion-selective electrode (ISE) with a wide sensing range centered around physiologically relevant pH values. The fluorophilic tris[perfluoro(octyl)butyl]amine (N[(CH₂)₄R_f8]₃) was synthesized and tested as a new H⁺ ionophore using a redesigned electrode body that provides excellent mechanical sealing and much improved measurement reliability. In a challenging 1 M KCl background, these fluorous-phase ISEs exhibit a sensing range from pH 2.2 to 11.2, which is one of the widest working ranges reported to date for ionophore-based H⁺ ISEs. High selectivities against common interfering ions such as K⁺, Na⁺, and Ca²⁺ were determined (selectivity coefficients: logK _H, K ^pot = - 11.6; logK _H, Na ^pot = - 12.4; logK _H, Ca ^pot < - 10.2). The use of the N[(CH₂)₄R_f8]₃ ionophore with its -(CH₂)₄- spacers separating the amino group from the strongly electron-withdrawing perfluorooctyl groups improved the potentiometric selectivity as compared to the less basic tris[perfluoro(octyl)propyl]amine ionophore. The use of N[(CH₂)₄R_f8]₃ also made the ISE less prone to counter anion failure (i.e., Donnan failure) at low pH than the use of tris[perfluoro(octyl)pentyl]amine with its longer -(CH₂)₅- spacers, which more effectively shield the amino center from the perfluorooctyl groups. In addition, we exposed both conventional plasticized PVC-phase pH ISEs and fluorous-phase pH ISEs to 10% serum for 5 days. Results show that the PVC-phase ISEs lost selectivity while their fluorous-phase counterparts did not.

Potentiometric Selectivities of Ionophore-Doped Ion-Selective Membranes: Concurrent Presence of Primary Ion or Interfering Ion Complexes of Multiple Stoichiometries

The selectivities of ionophore-doped ion-selective electrode (ISE) membranes are controlled by the stability and stoichiometry of the complexes between the ionophore, L, and the target and interfering ions (I ^zi and J ^zj, respectively). Well-accepted models predict how these selectivities can be optimized by selection of ideal ionophore-to-ionic site ratios, considering complex stoichiometries and ion charges. These models were developed for systems in which the target and interfering ions each form complexes of only one stoichiometry. However, for a few ISEs, the concurrent presence of two primary ion complexes of different stoichiometries, such as IL ^zi and IL₂ ^zi, was reported. Indeed, similar systems were probably often overlooked and are, in fact, more common than the exclusive formation of complexes of higher stoichiometry unless the ionophore is used in excess. Importantly, misinterpreted stoichiometries misguide the design of new ionophores and are likely to result in the formulation of ISE membranes with inferior selectivities. We show here that the presence of two or more complexes of different stoichiometries for a given ion may be inferred experimentally from careful interpretation of the potentiometric selectivities as a function of the ionophore-to-ionic site ratio or from calculations of complex concentrations using experimentally determined complex stabilities. Concurrent formation of JL ^zj and JL₂ ^zj complexes of an interfering ion is shown here to shift the ionophore-to-ionic site ratio that provides the highest selectivities. Formation of IL _n-1 ^zi and IL _n ^zi complexes of a primary ion is less of a concern because an optimized membrane typically contains an excess of ionophore, but lower than expected selectivities may be observed if the stepwise complex formation constant, K_ILn, is not sufficiently large and the ionophore-to-ionic site ratio does not markedly exceed n.

Ion Aggregation and R3N+-C(R)-H···NR3 Hydrogen Bonding in a Fluorous Phase

Potentiometric selectivities show that in fluorous ion-selective electrode membranes the tetrabutylammonium ion binds to fluorophilic proton ionophores. For the ionophore bis[3-(perfluorooctyl)propyl](2,2,2-trifluoroethyl)amine, this type of interaction is confirmed by the effect of the ionophore on the ionic conductivity of perfluoro(perhydrophenanthrene) solutions of a fluorophilic NBu₄⁺ salt. In this system, ion pairs, triple ions, and higher ionic aggregates dominate over single ions, and the ionophore increases the conductivity by favoring the formation of ion aggregates with a net charge. These observations are consistent with the formation of R₃N⁺-C(R)-H···NR₃ type hydrogen bonds between the nitrogen atom of the ionophore and the hydrogen atoms in the α position to the positively charged quaternary ammonium center of NBu₄⁺. Similar interactions were observed in a number of crystalline phases. To date, observations of C-H···N type hydrogen bonds in liquid phases have been very few, and solution-phase N⁺-C-H···N type hydrogen bonds have not been reported previously. Interestingly, no interactions between NBu₄⁺ and the more basic ionophore tridodecylamine were observed in conventional plasticized poly(vinyl chloride) membranes doped with the ionophore tridodecylamine, emphasizing the uniquely low polarity of fluorous phases.

One-dimensional ionic self-assembly in a fluorous solution: the structure of tetra-n-butylammonium tetrakis[3,5-bis(perfluorohexyl)phenyl]borate in perfluoromethylcyclohexane by small-angle neutron scattering (SANS)

Fluorous liquids are the least polarizable condensed phases known, and their nonpolar members form solutions with conditions the closest to being in vacuo. A soluble salt consisting of a large fluorophilic anion, tetrakis[3,5-bis(perfluorohexyl)phenyl]borate, and its counterion, tetra-n-butylammonium, dissolved in perfluoromethylcyclohexane produces ionic solutions with extremely low conductivity. These solutions were subjected to small-angle neutron scattering (SANS) to ascertain the solute structure. At concentrations of 9% mass fraction, the fluorophilic electrolyte forms straight, long (>160 Å) self-assembled structures that are, in essence, long, homogeneous cylinders. Molecular models were made assuming a requirement for electroneutrality on the shortest length scale possible. This shows a structure formed from a stack of alternating anions and cations, and the structures fit the experimental scattering well. At the lower concentration of 1%, the stacks of ion pairs are shorter and eventually break up to form solitary ion pairs in the solution. These characteristics suggest such conditions provide an interesting new way to form long, self-assembling ionic nanostructures with single-molecule diameters in free solution onto which various moieties could be attached.

Ion-selective electrodes with unusual response functions: simultaneous formation of ionophore-primary ion complexes with different stoichiometries

It is well known that the selectivity of an ion-selective electrode (ISE) depends on the stoichiometry of the complexes between its ionophore and the target and interfering ions. It is all the more surprising that the possibility for the simultaneous occurrence of multiple target ion complexes with different complex stoichiometries was mostly ignored in the past. Here, we report on the simultaneous formation of 1:1 and 1:2 complexes of a fluorophilic crown ether in fluorous ISE membranes and how this results in what looks like super-Nernstian responses. These increased response slopes are not caused by mass transfer limitations and can be readily explained with a phase boundary model, a finding that is supported by experimentally determined complex formation constants and excellent fits of response curves. Not only Cs(+) but also the smaller ions Li(+), Na(+), K(+), and NH(4)(+) form 1:1 and 1:2 complexes with the fluorophilic crown ether, with cumulative formation constants of up to 10(15.0) and 10(21.0) for of the 1:1 and 1:2 complexes, respectively. Super-Nernstian responses of the type observed with these electrodes are probably not particularly rare but have lacked in the past an adequate discussion in the literature, remaining ignored or misinterpreted. Preliminary calculations also predict sub-Nernstian responses and potential dips of a similar origin. The proper understanding of such phenomena will facilitate the development of new ISEs based on ionophores that form complexes of higher stoichiometries.

Potentiometric sensors based on fluorous membranes doped with highly selective ionophores for carbonate

Manganese(III) complexes of three fluorophilic salen derivatives were used to prepare ion-selective electrodes (ISEs) with ionophore-doped fluorous sensing membranes. Because of their extremely low polarity and polarizability, fluorous media are not only chemically very inert but also solvate potentially interfering ions poorly, resulting in a much improved discrimination of such ions. Indeed, the new ISEs exhibited selectivities for CO(3)(2-) that exceed those of previously reported ISEs based on nonfluorous membranes by several orders of magnitude. In particular, the interference from chloride and salicylate was reduced by 2 and 6 orders of magnitude, respectively. To achieve this, the selectivities of these ISEs were fine-tuned by addition of noncoordinating hydrophobic ions (i.e., ionic sites) into the sensing membranes. Stability constants of the anion-ionophore complexes were determined from the dependence of the potentiometric selectivities on the charge sign of the ionic sites and the molar ratio of ionic sites and the ionophore. For this purpose, a previously introduced fluorophilic tetraphenylborate and a novel fluorophilic cation with a bis(triphenylphosphoranylidene)ammonium group, (R(f6)(CH(2))(3))(3)PN(+)P(R(f6)(CH(2))(3))(3), were utilized (where R(f6) is C(6)F(13)). The optimum CO(3)(2-) selectivities were found for sensing membranes composed of anionic sites and ionophore in a 1:4 molar ratio, which results in the formation of 2:1 complexes with CO(3)(2-) with stability constants up to 4.1 × 10(15). As predicted by established theory, the site-to-ionophore ratios that provide optimum potentiometric selectivity depend on the stoichiometries of the complexes of both the primary and the interfering ions. However, the ionophores used in this study give examples of charges and stoichiometries previously neither explicitly predicted by theory nor shown by experiment. The exceptional selectivity of fluorous membranes doped with these carbonate ionophores suggests their use not only for potentiometric sensing but also for other types of sensors, such as the selective separation of carbonate from other anions and the sequestration of carbon dioxide.

A two-component polymeric optode membrane based on a multifunctional ionic liquid

This work details the use of a 2-component optode membrane which is capable of generating three distinct colours in the presence of Cu(2+) and Co(2+) ions. It has been found that the ionic liquid (IL) trihexyltetradecylphosphonium dicyanamide [P(6,6,6,14)][DCA] can act as plasticizer, ligand and transducer dye when used in poly(vinyl chloride) (PVC) membranes, which significantly simplifies the optode membrane cocktail. Upon exposure to an aqueous Cu(2+) solution, a yellow colour is generated within the membrane, while exposure to an aqueous Co(2+) solution generates a blue colour. Exposure to a solution containing both ions produces a green colour. Vibrational spectroscopy has been used to investigate the molecular basis of the IL-metal ion the binding mechanism. Analytical characteristics of the membranes including the effect of interfering ions, binding constants and the limit of detection for both ions have been estimated. Finally the case of simultaneous dual-analyte recognition is presented based on two distinct absorption maxima.

Highly selective detection of silver in the low ppt range with ion-selective electrodes based on ionophore-doped fluorous membranes

Ionophore-doped sensing membranes exhibit greater selectivities and wider measuring ranges if their membrane matrixes are noncoordinating and solvate interfering ions poorly. This is particularly true for fluorous phases, which are the least polar and polarizable condensed phases known. In this work, fluorous membrane matrixes were used to prepare silver ion-selective electrodes (ISEs). Sensing membranes composed of perfluoroperhydrophenanthrene, sodium tetrakis[3,5-bis(perfluorohexyl) phenyl]borate, and one of four fluorophilic Ag(+)-selective ionophores with one or two thioether groups were investigated. All electrodes exhibited Nernstian responses to Ag(+) in a wide range of concentrations. Their selectivities for Ag(+) over interfering ions were found to depend on host preorganization and the length of the -(CH(2))(n)- spacers separating the coordinating thioether group from the strongly electron withdrawing perfluoroalkyl groups. ISEs based on the most selective of the four ionophores, that is, 1,3-bis(perfluorodecylethylthiomethyl)benzene, provided much higher selectivities for Ag(+) over many alkaline and heavy metal ions than most Ag(+) ISEs reported in the literature (e.g., log K(Ag,J)(pot) for K(+), -11.6; Pb(2+), -10.2; Cu(2+), -13.0; Cd(2+), -13.2). Moreover, the use of this ionophore with a linear perfluorooligoether as membrane matrix and solid contacts consisting of three-dimensionally ordered macroporous (3DOM) carbon resulted in a detection limit for Ag(+) of 4.1 ppt (3.8 × 10(-1)1 M).

Properties and transport behavior of perfluorotripentylamine (FC-70)-doped amorphous teflon AF 2400 films

Teflon AF 2400 films are known to imbibe solvents, making films in the presence of solvents less fluorous than they might otherwise be. Herein, we demonstrate that doping films with perfluorotripentylamine (Fluorinert FC-70) maintains the fluorous nature of Teflon AF 2400 and improves transport selectivity for fluorine-containing organic compounds. Density measurements on the FC-70-doped films reveal that free volume decreases dramatically as the dopant concentration increases (0-12 wt %) and then increases to approach that of pure FC-70. Remarkably, films from 0 to 12 wt % FC-70 have the same w/v concentration of Teflon AF 2400, indicating that FC-70 fills the free volume of Teflon AF 2400. This is consistent with the observed increased storage modulus and significant decrease (compared to undoped films) of solute diffusion coefficients in the same range of FC-70 concentrations. In contrast, FC-70 at concentrations greater than 12 wt % dilutes Teflon AF 2400, leading to a decrease of storage modulus and dramatic increase in solute diffusion coefficients. Sorption of chloroform decreases from 11.8 g of chloroform/100 g of film (pure Teflon film) to 3.8 g of chloroform/100 g of film (27 wt % FC-70-doped Teflon film), less than the solubility of chloroform in pure FC-70 (4.06 g of chloroform/100 g of FC-70). Solute partition coefficients from chloroform to FC-70-doped films generally decrease with increased dopant concentration. However, within a series of toluenes and nitrobenzenes, selectivity for F-containing solutes over analogous H-containing solutes increases as dopant concentration increases if the substitution is on the aromatic ring but not if it is on the methyl group (toluene). Transport (partitioning × diffusion) rates, as they involve both thermodynamic and kinetic factors, are not simply related to composition.

Electrochemistry in Media of Exceptionally Low Polarity: Voltammetry with a Fluorous Solvent

This work demonstrates the first cyclic voltammetry in a perfluorocarbon solvent without use of a cosolvent. The novel electrolyte tetrabutylammonium tetrakis[3,5-bis(perfluorohexyl)phenyl]borate (NBu(4)BArF(104); 80 mM) allows for voltammetry of ferrocene in perfluoro(methylcyclohexane) by lowering the specific resistance to Ω268 k cm at 20.8 °C. Despite significant solution resistance, the resulting voltammograms can be fitted quantitatively without difficulty. The thus determined standard electron transfer rate constant, k°, for the oxidation of ferrocene in perfluoro(methylcyclohexane) is somewhat smaller than for many solvents commonly used in electrochemistry, but can be explained readily as the result of the viscosity and size of the solvent using Marcus theory. Dielectric dispersion spectroscopy verifies that addition of NBu(4)BArF(104) does not significantly raise the overall polarity of the solution over that of neat perfluoro(methylcyclohexane).

Cation-Coordinating Properties of Perfluoro-15-Crown-5

The coordinative properties of perfluoro-15-crown-5 with monocations were investigated using (19)F NMR spectroscopy and ion-selective electrodes with perfluoro-15-crown-5 as the matrix of their sensor membranes and the fluorophilic tetrakis[3,5-bis(perfluorohexyl)phenyl]borate as ion exchanger site. The results show that perfluoro-15-crown-5 interacts weakly but significantly with Na(+) and K(+). Assuming 1:1 stoichiometry, the formal complexation constants were determined to be 5.5 and 1.7 M(-1), respectively. This weak binding is consistent with the strong electron withdrawing nature of the many fluorine atoms in the perfluorocrown ether. While perfluorinated crown ethers have been known to form host-guest complexes with the anions O(2) (-) and F(-) in the gas phase, this is the first study that quantitatively confirms cation binding to a perfluorocrown ether.

Fluorous polymeric membranes for ionophore-based ion-selective potentiometry: how inert is Teflon AF?

Fluorous media are the least polar and polarizable condensed phases known. Their use as membrane materials considerably increases the selectivity and robustness of ion-selective electrodes (ISEs). In this research, a fluorous amorphous perfluoropolymer was used for the first time as a matrix for an ISE membrane. Electrodes for pH measurements with membranes composed of poly[4,5-difluoro-2,2-bis(trifluoromethyl)-1,3-dioxole]-co-poly(tetrafluoroethylene) (87% dioxole monomer content; known as Teflon AF2400) as polymer matrix, a linear perfluorooligoether as plasticizer, sodium tetrakis[3,5-bis(perfluorohexyl)phenyl]borate providing for ionic sites, and bis[(perfluorooctyl)propyl]-2,2,2-trifluoroethylamine as H+ ionophore were investigated. All electrodes had excellent potentiometric selectivities, showed Nernstian responses to H+ over a wide pH range, exhibited enhanced mechanical stability, and maintained their selectivity over at least 4 weeks. For membranes of low ionophore concentration, the polymer affected the sensor selectivity noticeably at polymer concentrations exceeding 15%. Also, the membrane resistance increased quite strongly at high polymer concentrations, which cannot be explained by the Mackie-Meares obstruction model. The selectivities and resistances depend on the polymer concentration because of a functional group associated with Teflon AF2400, with a concentration of one functional group per 854 monomer units of the polymer. In the fluorous environment of these membranes, this functional group binds to Na+, K+, Ca2+, and the unprotonated ionophore with binding constants of 10(3.5), 10(1.8), 10(6.8), and 10(4.4) M(-1), respectively. Potentiometric and spectroscopic evidence indicates that these functional groups are COOH groups formed by the hydrolysis of carboxylic acid fluoride (COF) groups originally present in Teflon AF2400. The use of higher ionophore concentrations removes the undesirable effect of these COOH groups almost completely. Alternatively, the C(=O)F groups can be eliminated chemically, or they can be used to readily introduce new functionalities.

Preparation of a Highly Fluorophilic Phosphonium Salt and its Use in a Fluorous Anion-Exchanger Membrane with High Selectivity for Perfluorinated Acids

Fluorous solvents are the most nonpolar, nonpolarizable phases known, whereas ions are inherently polar. This makes it difficult to create salts that are soluble in a fluorous solvent. Here we present the synthesis and characterization of a new fluorophilic phosphonium salt, tris{3,5-bis[(perfluorooctyl)propyl]phenyl}methylphosphonium methyl sulfate. The salt has a solubility of at least 14 mM in perfluoro(perhydrophenanthrene), perfluoro(methylcyclohexane), and perfluorohexanes. It also shows immediate potential for use as a phase-transfer catalyst in fluorous biphasic catalysis, but in this work it is used as an anion exchanger site in the first potentiometric fluorous-membrane anion-selective electrode. The membrane sensor exhibited the exceptional selectivity of 3.9 × 10(10) to 1 for perfluorooctanesulfonate over chloride, and of 2.5 × 10(7) to 1 for perfluorooctanoate over chloride. With improvements to the sensor's detection limit and lifetime, it has the potential to be an attractive alternative to the expensive, time-consuming methods currently employed for measurement of perfluorinated acids.