Scanning Electrochemical Microscopy: A Comprehensive Review of Experimental Parameters from 1989 to 2015

Assessment of Ti, Ir, Ta and Ru influence on mixed metal oxide electrodes for photoelectrochemical generation of persulfate: Impact on sulfamethoxazole degradation

The presence of persulfate (S2O82-) in decontamination processes favors the oxidation of organic pollutants due to its strong oxidation power. In this research we study the photoelectrochemical generation of persulfate using five mixed metal oxides electrodes (MMO) with different compositions and its effect on the degradation of sulfamethoxazole antibiotic (SMX) by photoelectrocatalysis (PEC) and electro-oxidation (EO). By PEC, all anodes generated a higher concentration of S2O82- than those not exposed to light. The high S2O82-concentration obtained by PEC was 0.150 mM using MMO[Ti/Ir/Ta] in a solution with Na2SO4 100 mM applying a current density of 2 mA/cm2. On the other hand, the maximum concentration obtained was 0.250 mM at 30 min of electrolysis for MMO[Ti/Ir/Ta] using Na2SO4 50 mM and applying current density of 5 mA/cm2. S2O82-production by EO was between 0.005 and 0.089 mM. It is observed that MMO based in Ta2O5 showed the best S2O82- production. The effect of S2O82- electro-generation (using the anode with the highest and the anode with the lowest S2O82- production) on the degradation of sulfamethoxazole by PEC and EO was studied using the experimental conditions with the best production of this oxidant. MMO[Ti/Ir/Ta] and MMO[Ti/Ru] were used as anodes, and it was observed that by PEC, 100% of SMX was degraded after 30 min of electrolysis using MMO[Ti/Ir/Ta] and 60 min using MMO[Ti/Ru]. By EO, the degradation of SMX was partial, demonstrating that the electrophotocatalytic effect favors the generation of S2O82-, enhancing the degradation of SMX at short electrolysis times.

Label-Free Imaging of Mesenchymal Stem Cell Spheroid Differentiation with Flexible-Probe SECM and a Microfluidic Device

Mesenchymal stem cells (MSCs) have emerged as an indispensable source for stem cell research and preclinical studies due to their capacity for in vitro proliferation and their potential to differentiate into mesodermal lineages, particularly into osteoblasts. This capability has propelled their application in the fields of bone regeneration and osteochondral repair. Traditional methodologies for assessing the differentiation status of MSCs necessitate invasive procedures such as cell lysis or fixation. In this study, we introduce a nondestructive technique that utilizes an integrated label-free approach to evaluate the osteogenic maturation of MSC spheroid aggregates. This method employs scanning electrochemical microscopy (SECM) with a flexible probe in conjunction with a top-removable microfluidic device designed for easy SECM access. By tracking the production rate of p-aminophenol (PAP) in the generation/collection mode and assessing morphological changes via the negative feedback mode using [Ru(NH3)6]Cl3 (Ruhex), we can discern variations in the alkaline phosphatase (ALP) activity indicative of osteogenic differentiation. This innovative strategy enables the direct evaluation of osteogenic differentiation in MSC spheroids cultured within microwell arrays without necessitating any labeling procedures. The utilization of a flexible microelectrode as the probe that scans in contact mode (with probe-substrate distances potentially as minimal as 0 μm) affords enhanced resolution compared to the traditional stiff-probe technique. Furthermore, this method is compatible with subsequent molecular biology assays, including gene expression analysis and immunofluorescence, thereby confirming the electrochemical findings and establishing the validity of this integrative approach.

Superalloys fracture process inference based on overlap analysis of 3D models

Superalloy materials exhibit susceptibility to fracture failures stemming from the influence of thermomechanical factors. To comprehensively understand the fracture mechanisms, material properties, root causes of failure, and the subsequent optimization of alloys, a detailed analysis of the internal fracture process and the morphological traits of the fracture surface is imperative. Traditional analysis of fracture surfaces solely relies on 2D images, thus lacking crucial 3D information. Although in situ experiments can capture the fracture process, their effectiveness is confined to the specimen's surface, precluding insight into internal changes. Here we introduce an integrated framework encompassing the process of 3D reconstruction of fracture surfaces, aiming to enhance the visual information obtained with micron-level accuracy, visual intuitiveness and sense of depth. Additionally, this framework also facilitates the scrutiny and inference of internal fracture processes. These results demonstrate that under specific service conditions, material deformation fracture probably stems from a combination of surface cracking and internal cracking rather than exclusively one or the other. Overall, our description and analysis of internally initiated cracking due to defects within the specimens can be beneficial in guiding future alloy design and optimization efforts.

Developments in anticorrosive organic coatings modulated by nano/microcontainers with porous matrices

The durability and functionality of many metallic structures are seriously threatened by corrosion, which makes the development of anticorrosive coatings imperative. This state-of-the-art survey explores the recent developments in the field of anticorrosive organic coatings modulated by innovations involving nano/microcontainers with porous matrices. The integration of these cutting-edge delivery systems seeks to improve the protective properties of coatings by enabling controlled release, extended durability, targeted application of corrosion inhibitors, and can be co-constructed to achieve defect filling by polymeric materials. The major highlight of this review is an in-depth analysis of the functionalities provided by porous nano/microcontainers in the active protection and self-healing of anticorrosive coatings, including their performance evaluation. In one case, after 20 days of immersion in 0.1 M NaCl, a scratched coating containing mesoporous silica nanoparticles loaded with an inhibitor benzotriazole and shelled with polydopamine (MSNs-BTA@PDA) exhibited coating restoration indicated by a sustained corrosion resistance rise over an extended period monitored by impedance values at 0.01 Hz frequency, rising from 8.3 × 104 to 7.0 × 105 Ω cm2, a trend assigned to active protection by the release of inhibitors and self-healing capabilities. Additionally, some functions related to anti-fouling and heat preservation by nano/microcontainers are highlighted. Based on the literature survey, some desirable properties, current challenges, and prospects of anticorrosive coatings doped with nano/microcontainers have been summarized. The knowledge gained from this survey will shape future research directions and applications in a variety of industrial areas, in addition to advancing smart corrosion prevention technology.

Particle Size-Tunable Polydopamine Nanoparticles for Optical and Electrochemical Imaging of Latent Fingerprints on Various Surfaces

Powder dusting method is the most widely used approach due to its low cost, simplicity, minimal instrument dependence, and extensive applicability for developing latent fingerprints (LFPs). Herein, a novel optical and electrochemical dual-mode method for high-resolution LFP enhancement has been explored based on size-tunable polydopamine (PDA) nanoparticles (NPs) and scanning electrochemical microscopy (SECM). Dark PDAs rich in functional groups and negative charges can combine with the residues of LFPs on various surfaces with high sensitivity and selectivity to realize high-resolution visual fingerprint physical patterns on various porous and nonporous substrates with light color. However, optical visualization is not feasible for LFPs on dark or multicolored surfaces. Fortunately, based on the differences in electrochemical reactivity between ridges and furrows caused by the conductivity and reducibility of PDA powders, SECM can serve as a powerful supplement to optical methods to effectively overcome background color interference and distinctly display fingerprint patterns. Intriguingly, it is noteworthy that the binding amount and particle size of PDA powder significantly affected the optical and electrochemical visualization of LFPs: more powder binding amounts provided darker ridges in optical, and more surface reaction sites (larger powder binding mass at the same particle size or smaller particle size at the same mass) provided higher currents of ridges in electrochemical imaging. It demonstrates that the PDA powder as a dual-mode developer for LFPs offers a promising method for individual identification in forensics.

Integration of Scanning Electrochemical Microscopy and Scanning Electrochemical Cell Microscopy in a Bifunctional Nanopipette toward Simultaneous Mapping of Activity and Selectivity in Electrocatalysis

Scanning electrochemical microscopy (SECM) and scanning electrochemical cell microscopy (SECCM) were integrated in a single bifunctional probe for simultaneous mapping of the oxygen reduction current and the oxidation current of the produced H2O2. The dual probe is fabricated from a double-barrel θ capillary, comprising one open barrel filled with the electrolyte and another filled with pyrolytic carbon. Pt is deposited with a gas injection system (GIS) at the end of the carbon barrel. The probe integrates the advantages of both SECM and SECCM by forming an electrochemical droplet cell that embeds the Pt working electrode of the carbon barrel directly into the electrolyte meniscus formed upon sample contact from the electrolyte barrel. The versatility of the dual probe is demonstrated by mapping the oxygen reduction reaction (ORR) current and the H2O2 oxidation current of a Pt microstrip on a gold substrate. This allows simultaneous localized electrochemical measurements, highlighting the potential of the dual probe for broader applications in characterizing the electrocatalytic properties of materials.

General Method for Fitting Kinetics from the SECM Images of Reactive Sites on Flat Surfaces

Scanning electrochemical microscopy (SECM) is a technique for imaging electrochemical reactions at a surface. The interaction between electrochemical reactions occurring at the sample and scanning electrode tip is quite complicated and requires computer modeling to obtain quantitative information from SECM images. Often, existing computer models must be modified, or a new model must be created from scratch to fit kinetic parameters for different reactive features. This work presents a method that can simulate the SECM image of a reactive feature of any shape on a flat surface which is coupled to a computer program which effectuates the automated fitting of kinetic information from these images. This fitting program is evaluated along with several methods for estimating the shapes of reactive features from their SECM images. Estimates of the reactive feature shape from SECM images were not sufficiently accurate and produced median relative errors for the surface rate constant that were >50%. Fortunately, more precise techniques for imaging the reactive features such as optical microscopy can supply sufficiently accurate shapes for the fitting procedure to produce accurate results. Fits of simulated SECM images using the actual shape from the simulation produced median relative errors for the surface rate constant that were <10% for the smallest reactive features tested. This method was applied to the SECM images of aluminum alloy AA7075 which revealed diffusion-limited kinetics for ferrocene methanol reduction over inclusions in the surface of the alloy.

Five years of scanning electrochemical cell microscopy (SECCM): new insights and innovations

Scanning electrochemical cell microscopy (SECCM) is a nanopipette-based technique which enables measurement of localised electrochemistry. SECCM has found use in a wide range of electrochemical applications, and due to the wider uptake of this technique in recent years, new applications and techniques have been developed. This minireview has collected all SECCM research articles published in the last 5 years, to demonstrate and celebrate the recent advances, and to make it easier for SECCM researchers to remain well-informed. The wide range of SECCM applications is demonstrated, which are categorised here into electrocatalysis, electroanalysis, photoelectrochemistry, biological materials, energy storage materials, corrosion, electrosynthesis, and instrumental development. In the collection of this library of SECCM studies, a few key trends emerge. (1) The range of materials and processes explored with SECCM has grown, with new applications emerging constantly. (2) The instrumental capabilities of SECCM have grown, with creative techniques being developed from research groups worldwide. (3) The SECCM research community has grown significantly, with adoption of the SECCM technique becoming more prominent.

Real-time investigation of reactive oxygen species and radicals evolved from operating Fe-N-C electrocatalysts during the ORR: potential dependence, impact on degradation, and structural comparisons

Improving the stability of platinum-group-metal-free (PGM-free) catalysts is a critical roadblock to the development of economically feasible energy storage and conversion technologies. Fe-N-C catalysts, the most promising class of PGM-free catalysts, suffer from rapid degradation. The generation of reactive oxygen species (ROS) during the oxygen reduction reaction (ORR) has been proposed as a central cause of this loss of activity. However, there is insufficient understanding of the generation and dynamics of ROS under catalytic conditions due to the difficulty of detecting and quantifying short-lived ROS such as the hydroxyl radical, OH˙. To accomplish this, we use operando scanning electrochemical microscopy (SECM) to probe the production of radicals by a commercial pyrolyzed Fe-N-C catalyst in real-time using a redox-active spin trap methodology. SECM showed the monotonic production of OH˙ which followed the ORR activity. Our results were thoroughly backed using electron spin resonance confirmation to show that the hydroxyl radical is the dominant radical species produced. Furthermore, OH˙ and H2O2 production followed distinct trends. ROS studied as a function of catalyst degradation also showed a decreased production, suggesting its relation to the catalytic activity of the sample. The structural origins of ROS production were also probed using model systems such as iron phthalocyanine (FePc) and Fe3O4 nanoparticles, both of which showed significant generation of OH˙ during the ORR. These results provide a comprehensive insight into the critical, yet under-studied, aspects of the production and effects of ROS on electrocatalytic systems and open the door for further mechanistic and kinetic investigation using SECM.

Unravelling the Bi-Functional Electrocatalytic Properties of {Mo72Fe30} Polyoxometalate Nanostructures for Overall Water Splitting Using Scanning Electrochemical Microscope and Electrochemical Gating Methods

This study reports the use of Keplerate-type {Mo72Fe30} polyoxometalate (POMs) nanostructures as a bi-functional-electrocatalyst for HER and OER in an alkaline medium with a lower overpotential (135 mV for HER and 264 mV for OER), and excellent electrochemical stability. The bi-functional catalytic properties of {Mo72Fe30} POM are studied using a scanning electrochemical microscope (SECM) via current mapping using substrate generation and tip collection mode. Furthermore, the bipolar nature of the {Mo72Fe30} POM nano-electrocatalysts is studied using the electrochemical gating via simultaneous monitoring of the electrochemical (cell) and electrical ({Mo72Fe30} POM) signals. Next, a prototype water electrolyzer fabricated using {Mo72Fe30} POM electrocatalysts showed they can drive 10 mA cm-2 with a low cell voltage of 1.62 V in lab-scale test conditions. Notably, the {Mo72Fe30} POM electrolyzers' performance assessment based on recommended conditions for industrial aspects shows that they require a very low overpotential of 1.89 V to drive 500 mA cm-2, highlighting their promising candidature toward clean-hydrogen production.

Investigation of the Electrocatalytic Reduction of Peroxydisulfate Using Scanning Electrochemical Microscopy

The elementary steps of the electrocatalytic reduction of S2O82- using the Ru(NH3)63+/2+ redox couple were investigated using scanning electrochemical microscopy (SECM) and steady-state voltammetry (SSV). SECM investigations were carried out in a 0.1 M KCl solution using a 3.5 μm radius carbon ultramicroelectrode (UME) as the SECM tip and a 25 μm radius platinum UME as the substrate electrode. Approach curves were recorded in the positive feedback mode of SECM by reducing Ru(NH3)63+ at the tip electrode and oxidizing Ru(NH3)62+ at the substrate electrode, as a function of the tip-substrate separation and S2O82- concentration. The one-electron reaction between electrogenerated Ru(NH3)62+ and S2O82- yields the unstable S2O83•-, which rapidly dissociates to produce highly oxidizing SO4•-. Because SO4•- is such a strongly oxidizing species, it can be further reduced at both the tip and the substrate, or it can react with Ru(NH3)62+ to regenerate Ru(NH3)63+. SECM approach curves display a complex dependence on the tip-substrate distance, d, due to redox mediation reactions at both the tip and the substrate. Finite element method (FEM) simulations of both SECM approach curves and SSV confirm a previously proposed mechanism for the mediated reduction of S2O82- using the Ru(NH3)63+/2+ redox couple. Our results provide a lower limit for dissociation rate constant of S2O83•- (∼1 × 106 s-1), as well as the rate constants for electron transfer between SO4•- and Ru(NH3)62+ (∼1 × 109 M-1 s-1) and between S2O82- and Ru(NH3)62+ (∼7 × 105 M-1 s-1).

Simultaneous Mapping of Electrocatalytic Activity and Selectivity via Hybrid Scanning Electrochemical Probe Microscopy

Nanoscale scanning electrochemical probe microscopy started to elucidate the heterogeneity of electrocatalytic activity at electrode surfaces. However, understanding the heterogeneity in product selectivity, another crucial aspect of interfacial reactivity, remains challenging. Herein, we introduce a method combining scanning electrochemical microscopy (SECM) and scanning electrochemical cell microscopy (SECCM) to enable the spatially resolved mapping of both activity and selectivity in electrocatalysis. A dual-channel nanopipette probe was developed: one channel for activity mapping and the other for product detection with a high collection efficiency (>95%) and sensitivity. Simultaneous mapping of activity and selectivity in the oxygen reduction reaction (ORR) is demonstrated. Combined with colocalized crystal orientation mapping, we uncover the local electrocatalytic performance of ORR at different facets on polycrystalline Pt and Au. The high-resolution selectivity mapping enabled by our method with colocalized structural characterization can provide structure-activity-selectivity relationships that are often unavailable in ensemble measurement, holding promise for understanding key structural motifs controlling interfacial reactivity.

Scanning electrochemical microscopy for determining oxygen consumption rates of cells in hydrogel fibers fabricated using an extrusion 3D bioprinter

Three-dimensional (3D)-cultured cells have attracted the attention of researchers in tissue engineering- and drug screening-related fields. Among them, 3D cellular fibers have attracted significant attention because they can be stacked to prepare more complex tissues and organs. Cellular fibers are widely fabricated using extrusion 3D bioprinters. For these applications, it is necessary to evaluate cellular activities, such as the oxygen consumption rate (OCR), which is one of the major metabolic activities. We previously reported the use of scanning electrochemical microscopy (SECM) to evaluate the OCRs of cell spheroids. However, the SECM approach has not yet been applied to hydrogel fibers prepared using the bioprinters. To the best of our knowledge, this is the first study to evaluate the OCR of cellular fibers printed by extrusion 3D bioprinters. First, the diffusion theory was discussed to address this issue. Next, diffusion models were simulated to compare realistic models with this theory. Finally, the OCRs of MCF-7 cells in the printed hydrogel fibers were evaluated as a proof of concept. Our proposed approach could potentially be used to evaluate the OCRs of tissue-engineered fibers for organ transplantation and drug screening using in-vitro models.

Scanning Probe Microscopies for Characterizations of 2D Materials

2D materials are intriguing due to their remarkably thin and flat structure. This unique configuration allows the majority of their constituent atoms to be accessible on the surface, facilitating easier electron tunneling while generating weak surface forces. To decipher the subtle signals inherent in these materials, the application of techniques that offer atomic resolution (horizontal) and sub-Angstrom (z-height vertical) sensitivity is crucial. Scanning probe microscopy (SPM) emerges as the quintessential tool in this regard, owing to its atomic-level spatial precision, ability to detect unitary charges, responsiveness to pico-newton-scale forces, and capability to discern pico-ampere currents. Furthermore, the versatility of SPM to operate under varying environmental conditions, such as different temperatures and in the presence of various gases or liquids, opens up the possibility of studying the stability and reactivity of 2D materials in situ. The characteristic flatness, surface accessibility, ultra-thinness, and weak signal strengths of 2D materials align perfectly with the capabilities of SPM technologies, enabling researchers to uncover the nuanced behaviors and properties of these advanced materials at the nanoscale and even the atomic scale.

Correlating activities and defects in (photo)electrocatalysts using in-situ multi-modal microscopic imaging

Photo(electro)catalysts use sunlight to drive chemical reactions such as water splitting. A major factor limiting photocatalyst development is physicochemical heterogeneity which leads to spatially dependent reactivity. To link structure and function in such systems, simultaneous probing of the electrochemical environment at microscopic length scales and a broad range of timescales (ns to s) is required. Here, we address this challenge by developing and applying in-situ (optical) microscopies to map and correlate local electrochemical activity, with hole lifetimes, oxygen vacancy concentrations and photoelectrode crystal structure. Using this multi-modal approach, we study prototypical hematite (α-Fe2O3) photoelectrodes. We demonstrate that regions of α-Fe2O3, adjacent to microstructural cracks have a better photoelectrochemical response and reduced back electron recombination due to an optimal oxygen vacancy concentration, with the film thickness and extended light exposure also influencing local activity. Our work highlights the importance of microscopic mapping to understand activity, in even seemingly homogeneous photoelectrodes.

Fast detection of micro-objects using scanning electrochemical microscopy based on visual recognition and machine learning

Scanning electrochemical microscopy (SECM) is a scanning probe microscope with an ultramicroelectrode (UME) as a probe. The technique is advantageous in the characterization of the electrochemical properties of surfaces. However, the limitations, such as slow imaging and many functions depending on the user, only allow us to use some of the possibilities. Therefore, we applied visual recognition and machine learning to detect micro-objects from the image and determine their electrochemical activity. The reconstruction of the image from several approach curves allows it to scan faster and detect active areas of the sample. Therefore, the scanning time and presence of the user is diminished. An automated scanning electrochemical microscope with visual recognition has been developed using commercially available modules, relatively low-cost components, design, software solutions proven in other fields, and an original control and data fusion algorithm.

Scanning electrochemical microscopy for the differentiation of radical-induced degradation mechanisms in polymer electrolyte membranes

In this work, a spatially resolved analytical method based on scanning electrochemical microscopy (SECM) to distinguish different degradation phenomena in polymer electrolyte membranes was developed. SECM was combined with a Franz diffusion cell to distinguish between radical-induced aging of a sulfonated tetrafluoroethylene based fluoropolymer-copolymer due to deactivation of the sulfonic acid groups followed by a decreased proton conductivity, and the radical-induced formation of cracks and holes in the polymer. The experiments were performed with ferrocyanide as redox mediator to detect holes and cracks, and protons (sulfuric acid) to determine the through-plane proton conductivity, respectively. A pristine Nafion™ membrane, a pristine Nafion™ membrane with an artificial pinhole and a Nafion™ membrane aged with Fenton's reagent were investigated to prove the measurement principle. It could be shown that holes and cracks can be reliably detected with this approach and discriminated from a change in proton conductivity. The presence of holes in the investigated aged membranes was confirmed by scanning electron microscopy, whereas the loss of sulfonate groups could be supported by infrared spectroscopy measurements.

Scanning Electrochemical Microscopy Reveals That Model Silicon Anodes Demonstrate Global Solid Electrolyte Interphase Passivation Degradation during Calendar Aging

Silicon is a promising next-generation anode to increase energy density over commercial graphite anodes, but calendar life remains problematic. In this work, scanning electrochemical microscopy was used to track the site-specific reactivity of a silicon thin film surface over time to determine if undesirable Faradaic reactions were occurring at the formed solid electrolyte interphase (SEI) during calendar aging in four case scenarios: formation between 1.5 V and 100 mV with subsequent rest starting at (1) 1.5 V and (2) 100 mV and formation between 0.75 V and 100 mV with subsequent rest starting at (3) 0.75 V and (4) 100 mV. In all cases, the electrical passivation of silicon decreased with increasing time and potential relative to Li/Li+ over a 3 day period. Along with the decrease in passivation, the homogeneity of passivation over a 500 μm2 area decreased with time. Despite some local "hot spots" of reactivity, the areal uniformity of passivation suggests global SEI failure (e.g., SEI dissolution) rather than localized (e.g., cracking) failure. The silicon delithiated to 1.5 V vs Li/Li+ was less passivated than the lithiated silicon (at the beginning of rest, the forward rate constants, kf, for ferrocene redox were 7.19 × 10-5 and 3.17 × 10-7 m/s, respectively) and was also found to be more reactive than the pristine silicon surface (kf of 5 × 10-5 m/s). This reactivity was likely the result of SEI oxidation. When the cell was only delithiated up to 0.75 V versus Li/Li+, the surface was still passivating (kf of 6.11 × 10-6 m/s), but still less so than the lithiated surface (kf of 3.03 × 10-9 m/s). This indicates that the potential of the anode should be kept at or below ∼0.75 V vs Li/Li+ to prevent decreasing SEI passivation. This information will help with tuning the voltage windows for prelithiation in Si half cells and the operating voltage of Si full cells to optimize calendar life. The results provided should encourage the research community to investigate chemical, rather than mechanical, modes of failure during calendar aging and to stop using the typical convention of 1.5 V as a cutoff potential for cycling Si in half cells.

Exploring the Living Cell: Applications and Advances of Scanning Electrochemical Microscopy

A living cell is a complex network of molecular, biochemical and physiological processes. Cellular activities, such as ion transport, metabolic processes, and cell-cell interactions can be determined electrochemically by detecting the electrons or ions exchanged in these processes. Electrochemical methods often are noninvasive, and they can enable the real-time monitoring of cellular processes. Scanning electrochemical microscopy (SECM) is an advanced scanning probe electroanalysis technique that can map the surface topography and local reactivity of a substrate with high precision at the micro- or nanoscale. By measuring electrochemical signals, such as redox reactions, ion fluxes, and pH changes, SECM can provide valuable insights into cellular activity. As a result of its compatibility with liquid medium measurements and its nondestructive nature, SECM has gained popularity in living cell research. This review aims to furnish an overview of SECM, elucidating its principles, applications, and its potential to contribute significantly to advancements in cell biology, electroporation, and biosensors. As a multidisciplinary tool, SECM is distinguished by its ability to unravel the intricacies of living cells and offers promising avenues for breakthroughs in our understanding of cellular complexity.

Direct Seawater Electrolysis: From Catalyst Design to Device Applications

Direct seawater electrolysis (DSE) for hydrogen production, using earth-abundant seawater as the feedstock and renewable electricity as the driving source, paves a new opportunity for flexible energy conversion/storage and smooths the volatility of renewable energy. Unfortunately, the complex environments of seawater impose significant challenges on the design of DSE catalysts, and the practical performance of many current DSE catalysts remains unsatisfactory on the device level. However, many studies predominantly concentrate on the development of electrocatalysts for DSE without giving due consideration to the specific devices. To mitigate this gap, the most recent progress (mainly published within the year 2020-2023) of DSE electrocatalysts and devices are systematically evaluated. By discussing key bottlenecks, corresponding mitigation strategies, and various device designs and applications, the tremendous challenges in addressing the trade-off among activity, stability, and selectivity for DSE electrocatalysts by a single shot are emphasized. In addition, the rational design of the DSE electrocatalysts needs to align with the specific device configuration, which is more effective than attempting to comprehensively enhance all catalytic parameters. This work, featuring the first review of this kind to consider rational catalyst design in the framework of DSE devices, will facilitate practical DSE development.

Investigating the Role of Extracellular Matrix Stiffness in Modulating the Ferroptosis Process in Hepatocellular Carcinoma Cells via Scanning Electrochemical Microscopy

Extracellular matrix (ECM) stiffness modulates a variety of cellular processes, including ferroptosis, a process with significant potential implications for hepatocellular carcinoma (HCC) fibrosis and cirrhosis. However, the exact relationship between ECM stiffness and HCC ferroptosis is yet unclarified, partially due to the lack of in situ information on key parameters of the ferroptosis process of living HCC cells. This study pioneers the use of in vitro mechanical microenvironment models of HCC and the scanning electrochemical microscopy (SECM) technique for understanding this interplay. We first cultured HuH7 cells on 4.0, 18.0, and 44.0 kPa polyacrylamide (PA) gels to simulate early, intermediate, and advanced HCC ECM stiffness, respectively. Then, we used SECM to in situ monitor changes in cell membrane permeability, respiratory activity, and reactive oxygen species (ROS) levels of erastin-induced HuH7 cells on PA gels, finding that increasing ECM stiffness potentiates ferroptosis, including increased membrane permeabilization and H2O2 release as well as reduced respiratory activity. Through further transcriptome sequencing and molecular biology measurements, we identified a critical role for focal adhesion kinase (FAK)-mediated yes-associated protein (YAP) in regulating the ferroptosis process dependent on ECM stiffness, which provides novel insights into the mechanical regulation of ferroptosis in HCC cells and may pave the way for innovative therapeutic strategies.

Cytochrome c oxidase deficiency detection in human fibroblasts using scanning electrochemical microscopy

Cytochrome c oxidase deficiency (COXD) is an inherited disorder characterized by the absence or mutation in the genes encoding for the cytochrome c oxidase protein (COX). COX deficiency results in severe muscle weakness, heart, liver, and kidney disorders, as well as brain damage in infants and adolescents, leading to death in many cases. With no cure for this disorder, finding an efficient, inexpensive, and early means of diagnosis is essential to minimize symptoms and long-term disabilities. Furthermore, muscle biopsy, the traditional detection method, is invasive, expensive, and time-consuming. This study demonstrates the applicability of scanning electrochemical microscopy to quantify COX activity in living human fibroblast cells. Taking advantage of the interaction between the redox mediator N, N, N', N'-tetramethyl-para-phenylene-diamine, and COX, the enzymatic activity was successfully quantified by monitoring current changes using a platinum microelectrode and determining the apparent heterogeneous rate constant k0 using numerical modeling. This study provides a foundation for developing a diagnostic method for detecting COXD in infants, which has the potential to increase treatment effectiveness and improve the quality of life of affected individuals.

Comparative Studies of Atomically Thin Proton Conductive Films to Reduce Crossover in Hydrogen Fuel Cells

Hydrogen fuel cells based on proton exchange membrane fuel cell (PEMFC) technology are promising as a source of clean energy to power a decarbonized future. However, PEMFCs are limited by a number of major inefficiencies; one of the most significant is hydrogen crossover. In this work, we comprehensively study the effects of two-dimensional (2D) materials applied to the anode side of the membrane as H2 barrier coatings on Nafion to reduce crossover effects on hydrogen fuel cells, while studying adverse effects on conductivity and catalyst performance in the beginning of life testing. The barrier layers studied include graphene, hexagonal boron nitride (hBN), amorphous boron nitride (aBN), and varying thicknesses of molybdenum disulfide (MoS2), all chosen due to their expected stability in a fuel cell environment. Crossover mitigation in the materials studied ranges from 4.4% (1 nm MoS2) to 46.1% (graphene) as compared to Nafion 211. Effects on proton conductivity are also studied, suggesting high areal proton transport in materials previously thought to be effectively nonconductive, such as 2 nm MoS2 and amorphous boron nitride under the conditions studied. The results indicate that a number of 2D materials are able to improve crossover effects, with those coated with 8 nm MoS2 and 1 L graphene able to achieve greater crossover reduction while minimizing conductivity penalty.

Interphase Modulated Early-Stage Zn Electrodeposition Mechanism

Zn electrodeposition mechanism is a cornerstone of dendritic issue exploration in Zn-ion battery. Investigation of the inherent early-stage Zn plating kinetics and its dependence on the reactivity of anode-electrolyte interphase is crucial. Herein, the kinetic evolution of Zn plating on three characteristic substrates is quantified: fresh Zn, commercial Zn foil, and Zn foil with spontaneously generated solid-electrolyte interphase (SEI). Using scanning electrochemical microscopy analysis, the original interphase regulation of Zn deposit orientation and the competitive reaction between Zn deposition and SEI passivation are studied in situ. Furthermore, the SEI layer can suppress the dendrite growth at initial state by guiding the horizontal alignment of Zn flakes and promote Zn plating process. This approach provided a feasible consideration into interphase engineering of various metal anodes.

In situ Observation of Evolving H2 and Solid Electrolyte Interphase Development at Potassium Insertion Materials within Highly Concentrated Aqueous Electrolytes

The solid-electrolyte interphase (SEI) is key to stable, high voltage lithium-ion batteries (LIBs) as a protective barrier that prevents electrolyte decomposition. The SEI is thought to play a similar role in highly concentrated water-in-salt electrolytes (WISEs) for emerging aqueous batteries, but its properties remain unknown. In this work, we utilized advanced scanning electrochemical microscopy (SECM) and operando electrochemical mass spectrometry (OEMS) techniques to gain deeper insight into the SEI that occurs within highly concentrated WISEs. As a model, we focus on a 55 mol/kg K(FSA)0.6 (OTf)0.4 electrolyte and a 3,4,9,10-perylenetetracarboxylic diimide negative electrode. For the first time, our work showed distinctly passivating structures with slow apparent electron transfer rates alike to the SEI found in LIBs. In situ analyses indicated stable passivating structures when PTCDI was stepped to low potentials (≈-1.3 V vs. Ag/AgCl). However, the observed SEI was discontinuous at the surface and H2 evolution occurred as the electrode reached more extreme potentials. OEMS measurements further confirmed a shift in the evolution of detectable H2 from -0.9 V to <-1.4 V vs. Ag/AgCl when changing from dilute to concentrated electrolytes. In all, our work shows a combined approach of traditional battery measurements with in situ analyses for improving characterization of other unknown SEI structures.

Can Single Cell Respiration be Measured by Scanning Electrochemical Microscopy (SECM)?

Ultramicroelectrode (UME), or, equivalently, microelectrode, probes are increasingly used for single-cell measurements of cellular properties and processes, including physiological activity, such as metabolic fluxes and respiration rates. Major challenges for the sensitivity of such measurements include: (i) the relative magnitude of cellular and UME fluxes (manifested in the current); and (ii) issues around the stability of the UME response over time. To explore the extent to which these factors impact the precision of electrochemical cellular measurements, we undertake a systematic analysis of measurement conditions and experimental parameters for determining single cell respiration rates via the oxygen consumption rate (OCR) in single HeLa cells. Using scanning electrochemical microscopy (SECM), with a platinum UME as the probe, we employ a self-referencing measurement protocol, rarely employed in SECM, whereby the UME is repeatedly approached from bulk solution to a cell, and a short pulse to oxygen reduction reaction (ORR) potential is performed near the cell and in bulk solution. This approach enables the periodic tracking of the bulk UME response to which the near-cell response is repeatedly compared (referenced) and also ensures that the ORR near the cell is performed only briefly, minimizing the effect of the electrochemical process on the cell. SECM experiments are combined with a finite element method (FEM) modeling framework to simulate oxygen diffusion and the UME response. Taking a realistic range of single cell OCR to be 1 × 10-18 to 1 × 10-16 mol s-1, results from the combination of FEM simulations and self-referencing SECM measurements show that these OCR values are at, or below, the present detection sensitivity of the technique. We provide a set of model-based suggestions for improving these measurements in the future but highlight that extraordinary improvements in the stability and precision of SECM measurements will be required if single cell OCR measurements are to be realized.

On-chip electrocatalytic microdevices

On-chip electrocatalytic microdevices (OCEMs) are an emerging electrochemical platform specialized for investigating nanocatalysts at the microscopic level. The OCEM platform allows high-precision electrochemical measurements at the individual nanomaterial level and, more importantly, offers unique perspectives inaccessible with conventional electrochemical methods. This protocol describes the critical concepts, experimental standardization, operational principles and data analysis of OCEMs. Specifically, standard protocols for the measurement of the electrocatalytic hydrogen evolution reaction of individual 2D nanosheets are introduced with data validation, interpretation and benchmarking. A series of factors (e.g., the exposed area of material, the choice of passivation layer and current leakage) that could have effects on the accuracy and reliability of measurement are discussed. In addition, as an example of the high adaptability of OCEMs, the protocol for in situ electrical transport measurement is detailed. We believe that this protocol will promote the general adoption of the OCEM platform and inspire further development in the near future. This protocol requires essential knowledge in chemical synthesis, device fabrication and electrochemistry.

Edge and Basal Plane Anisotropy of a Preanodized Pencil Graphite Electrode Surface Revealed Using Scanning Electrochemical Microscopy and Electrocatalytic Dopamine Oxidation as a Molecular Probe

Pencil graphite (PGE), an ultralow-cost and ready-to-use disposable-type electrode, has been used for various electrochemical and electroanalytical applications after its surface anodization (PGE*, * means preanodized surface). Indeed, systematic studies on mechanistic and surface features of PGE* have not yet been explored. Herein, we report anodized pencil graphite as a model system to study molecular level insights into the surface using a scanning electrochemical microscopy (SECM) technique and dopamine (DA) electrocatalytic oxidation reaction as a molecular probe. The as-prepared PGE* showed an appreciable electronic conductivity similar to the edge-plane graphitic sites (EPPG) of the highly pyrolytic graphitic electrode (HOPG) but without any surface deterioration that occurs with HOPG due to the instability of the EPPG. Physicochemical characterizations by FESEM, FTIR, Raman, and XPS techniques revealed a flake-like exfoliated PGE* surface with higher contents of carbon-oxygen especially phenolic/alcoholic functional groups than the PGE surface. Based on the chronocoulometric experiment, the number of functional groups formed on the PGE* was calculated as 10.9 × 10-10 mol cm-2. An independent SECM technique using ferricyanide as a redox probe showed the existence of a heterogeneous surface and exhibited an improved electron transfer activity due to the flake-like graphitic island on the PGE* surface. Investigated DA electrochemical oxidation on PGE* yielded about three times enhancement in the peak current signal and about 200 mV reduction in the oxidation potential over the PGE without any serious surface fouling feature that is related to the intermediate polydopamine formation on the basal-plane graphitic surface of the underlying electrode. As an independent electroanalytical study, a prototype electrochemical sensor using PGE* as a working electrode for instant detection of DA-containing pharmaceutical samples in a 1 mL Eppendorf vial has been demonstrated.

Visualizing the role of applied voltage in non-metal electrocatalysts

Understanding how applied voltage drives the electrocatalytic reaction at the nanoscale is a fundamental scientific problem, particularly in non-metallic electrocatalysts, due to their low intrinsic carrier concentration. Herein, using monolayer molybdenum disulfide (MoS2) as a model system of non-metallic catalyst, the potential drops across the basal plane of MoS2 (ΔVsem) and the electric double layer (ΔVedl) are decoupled quantitatively as a function of applied voltage through in-situ surface potential microscopy. We visualize the evolution of the band structure under liquid conditions and clarify the process of EF keeping moving deep into Ec, revealing the formation process of the electrolyte gating effect. Additionally, electron transfer (ET) imaging reveals that the basal plane exhibits high ET activity, consistent with the results of surface potential measurements. The potential-dependent behavior of kf and ns in the ET reaction are further decoupled based on the measurements of ΔVsem and ΔVedl. Comparing the ET and hydrogen evolution reaction imaging results suggests that the low electrocatalytic activity of the basal plane is mainly due to the absence of active sites, rather than its electron transfer ability. This study fills an experimental gap in exploring driving forces for electrocatalysis at the nanoscale and addresses the long-standing issue of the inability to decouple charge transfer from catalytic processes.

Concerning the stability of seawater electrolysis: a corrosion mechanism study of halide on Ni-based anode

The corrosive anions (e.g., Cl-) have been recognized as the origins to cause severe corrosion of anode during seawater electrolysis, while in experiments it is found that natural seawater (~0.41 M Cl-) is usually more corrosive than simulated seawater (~0.5 M Cl-). Here we elucidate that besides Cl-, Br- in seawater is even more harmful to Ni-based anodes because of the inferior corrosion resistance and faster corrosion kinetics in bromide than in chloride. Experimental and simulated results reveal that Cl- corrodes locally to form narrow-deep pits while Br- etches extensively to generate shallow-wide pits, which can be attributed to the fast diffusion kinetics of Cl- and the lower reaction energy of Br- in the passivation layer. Additionally, for the Ni-based electrodes with catalysts (e.g., NiFe-LDH) loading on the surface, Br- causes extensive spalling of the catalyst layer, resulting in rapid performance degradation. This work clearly points out that, in addition to anti-Cl- corrosion, designing anti-Br- corrosion anodes is even more crucial for future application of seawater electrolysis.

A Brief Review of In Situ and Operando Electrochemical Analysis of Bacteria by Scanning Probes

Bacteria are similar to social organisms that engage in critical interactions with one another, forming spatially structured communities. Despite extensive research on the composition, structure, and communication of bacteria, the mechanisms behind their interactions and biofilm formation are not yet fully understood. To address this issue, scanning probe techniques such as atomic force microscopy (AFM), scanning electrochemical microscopy (SECM), scanning electrochemical cell microscopy (SECCM), and scanning ion-conductance microscopy (SICM) have been utilized to analyze bacteria. This review article focuses on summarizing the use of electrochemical scanning probes for investigating bacteria, including analysis of electroactive metabolites, enzymes, oxygen consumption, ion concentrations, pH values, biofilms, and quorum sensing molecules to provide a better understanding of bacterial interactions and communication. SECM has been combined with other techniques, such as AFM, inverted optical microscopy, SICM, and fluorescence microscopy. This allows a comprehensive study of the surfaces of bacteria while also providing more information on their metabolic activity. In general, the use of scanning probes for the detection of bacteria has shown great promise and has the potential to provide a powerful tool for the study of bacterial physiology and the detection of bacterial infections.

Triple-Barrel Ultramicroelectrodes for Multipurpose, Submilliliter Electroanalysis

Here, we have developed and applied a triple-barrel microelectrode. This device incorporates a platinum disk working electrode, a platinum disk counter electrode, and a low-leakage Ag/AgCl reference electrode into a small probe. We demonstrate that the incorporated low-leakage reference electrode shows similar voltammetry, potentiometry, and drift when compared to a commercial reference electrode in bulk solution. We also demonstrate the versatility of such a small three-channel system via voltammetry in nanoliter droplets and through electroanalysis of captured aerosols. Finally, we demonstrate the probe's potential utility in single-cell electroanalysis by making measurements within salmon eggs.

An Integrated, Exchangeable Three-Electrode Electrochemical Setup for AFM-Based Scanning Electrochemical Microscopy

Scanning electrochemical microscopy (SECM) is a versatile scanning probe technique that allows monitoring of a plethora of electrochemical reactions on a highly resolved local scale. SECM in combination with atomic force microscopy (AFM) is particularly well suited to acquire electrochemical data correlated to sample topography, elasticity, and adhesion, respectively. The resolution achievable in SECM depends critically on the properties of the probe acting as an electrochemical sensor, i.e., the working electrode, which is scanned over the sample. Hence, the development of SECM probes received much attention in recent years. However, for the operation and performance of SECM, the fluid cell and the three-electrode setup are also of paramount importance. These two aspects received much less attention so far. Here, we present a novel approach to the universal implementation of a three-electrode setup for SECM in practically any fluid cell. The integration of all three electrodes (working, counter, and reference) near the cantilever provides many advantages, such as the usage of conventional AFM fluid cells also for SECM or enables the measurement in liquid drops. Moreover, the other electrodes become easily exchangeable as they are combined with the cantilever substrate. Thereby, the handling is improved significantly. We demonstrated that high-resolution SECM, i.e., resolving features smaller than 250 nm in the electrochemical signal, could be achieved with the new setup and that the electrochemical performance was equivalent to the one obtained with macroscopic electrodes.

Scanning Electrochemical Microscopy for Chemical Imaging and Understanding Redox Activities of Battery Materials

Improving the charge storage capacity and lifetime and charging/discharging efficiency of battery systems is essential for large-scale applications such as long-term grid storage and long-range automobiles. While there have been substantial improvements over the past decades, further fundamental research would help provide insights into improving the cost effectiveness of such systems. For example, it is critical to understand the redox activities of cathode and anode electrode materials and stability and the formation mechanism and roles of the solid-electrolyte interface (SEI) that forms at the electrode surface upon an external potential bias. The SEI plays a critical role in preventing electrolyte decay while still allowing charges to flow through the system while serving as a charge transfer barrier. While surface analytical techniques such as X-ray photoelectron (XPS), X-ray diffraction (XRD), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and atomic force microscopy (AFM) provide invaluable information on anode chemical composition, crystalline structure, and morphology, they are often performed ex situ, which can induce changes to the SEI layer after it is removed from the electrolyte. While there have been efforts to combine these techniques using pseudo-in situ approaches via vacuum-compatible devices and inert atmosphere chambers connected to glove boxes, there is still a need for true in situ techniques to obtain results with improved accuracy and precision. Scanning electrochemical microscopy (SECM) is an in situ scanning probe technique that can be combined with optical spectroscopy techniques such as Raman and photoluminescence spectroscopy methods to gain insights into the electronic changes of a material as a function of applied bias. This Review will highlight the potential of SECM and recent reports on combining spectroscopic measurements with SECM to gain insights into the SEI layer formation and redox activities of other battery electrode materials. These insights provide invaluable information for improving the performance of charge storage devices.

Exploring the pH Sensitivity of Ion-Pair Interactions on a Self-Assembled Monolayer by Scanning Electrochemical Microscopy

Insights into the chemical essence of weak interactions on the surface of biomacromolecules may help to regulate biological processes. In this work, the pH sensitivity of ion-pair interactions occurring on a cysteine self-assembled monolayer (Cys SAM) that simulates the local surface of a protein was probed by scanning electrochemical microscopy (SECM). Cys SAM and the ion-pair interactions subsequently formed with the introduced aspartic acid (Asp) were both pH-sensitive, as confirmed by the tip current changes in the feedback mode. After continuous pH measurements, the most significant negative feedback was observed at pH 5.50, indicating the most robust ion-pair interactions, which were simultaneously identified by voltammetry. In this case, the extra addition of the inorganic cation (i.e., Ca²⁺) did not disrupt the existing ion-pair interactions, and the binding constant (K) and Gibbs free energy (ΔG^o) of the ion pair were finally determined to be 6.44 × 10⁵ M^-1 and -33.14 kJ mol^-1, respectively. Overall, the pH sensitivity of ion-pair interactions was found to be mainly attributable to pH-induced changes in the deprotonated/protonated states of the α-amino acid moieties, which may provide insights into the artificial manipulation of complex binding events at the molecular level on the biological surface.

Profiling H2O2 from single COS-7 cells by means of scanning electrochemical microscopy

We report quantitative determination of extracellular H₂O₂ released from single COS-7 cells with high spatial resolution, using scanning electrochemical microscopy (SECM). Our strategy of depth scan imaging in vertical x-z plane was conveniently utilized to a single cell for obtaining probe approach curves (PACs) to any positions on the membrane of a live cell by simply drawing a vertical line on one depth SECM image. This SECM mode provides an efficient way to record a batch of PACs, and visualize cell topography simultaneously. The H₂O₂ concentration at the membrane surface in the center of an intact COS-7 cell was deconvoluted from apparent O₂, and determined to be 0.020 mM by overlapping the experimental PAC with the simulated one having a known H₂O₂ release value. The H₂O₂ profile determined in this way gives insight into physiological activity of single live cells. In addition, intracellular H₂O₂ profile was demonstrated using confocal microscopy by labelling the cells with a luminomphore, 2',7'-dichlorodihydrofluorescein diacetate. The two methodologies have illustrated complementary experimental results of H₂O₂ detection, indicating that H₂O₂ generation is centered at endoplasmic reticula.

Deconvoluting Kinetic Rate Constants of Catalytic Substrates from Scanning Electrochemical Approach Curves with Artificial Neural Networks

Extracting information from experimental measurements in the chemical sciences typically requires curve fitting, deconvolution, and/or solving the governing partial differential equations via numerical (e.g., finite element analysis) or analytical methods. However, using numerical or analytical methods for high-throughput data analysis typically requires significant postprocessing efforts. Here, we show that deep learning artificial neural networks can be a very effective tool for extracting information from experimental data. As an example, reactivity and topography information from scanning electrochemical microscopy (SECM) approach curves are highly convoluted. This study utilized multilayer perceptrons and convolutional neural networks trained on simulated SECM data to extract kinetic rate constants of catalytic substrates. Our key findings were that multilayer perceptron models performed very well when the experimental data were close to the ideal conditions with which the model was trained. However, convolutional neural networks, which analyze images as opposed to direct data, were able to accurately predict the kinetic rate constant of Fe-doped nickel (oxy)hydroxide catalyst at different applied potentials even though the experimental approach curves were not ideal. Due to the speed at which machine learning models can analyze data, we believe this study shows that artificial neural networks could become powerful tools in high-throughput data analysis.

Operando Scanning Electrochemical Probe Microscopy during Electrocatalysis

Scanning electrochemical probe microscopy (SEPM) techniques can disclose the local electrochemical reactivity of interfaces in single-entity and sub-entity studies. Operando SEPM measurements consist of using a SEPM tip to investigate the performance of electrocatalysts, while the reactivity of the interface is simultaneously modulated. This powerful combination can correlate electrochemical activity with changes in surface properties, e.g., topography and structure, as well as provide insight into reaction mechanisms. The focus of this review is to reveal the recent progress in local SEPM measurements of the catalytic activity of a surface toward the reduction and evolution of O₂ and H₂ and electrochemical conversion of CO₂. The capabilities of SEPMs are showcased, and the possibility of coupling other techniques to SEPMs is presented. Emphasis is given to scanning electrochemical microscopy (SECM), scanning ion conductance microscopy (SICM), electrochemical scanning tunneling microscopy (EC-STM), and scanning electrochemical cell microscopy (SECCM).

Physical visualization and squalene-based scanning electrochemical microscopy imaging of latent fingerprints on PVDF membrane

Fingerprints have long been the gold standard for personal identification in forensic science. However, realizing the high-resolution enhancement of eccrine LFPs is difficult using the traditional methods and the label-free detection of fingerprint residue information is also challenging. Herein, we propose two enhancement strategies for LFPs on PVDF membrane (LFPs/PVDF) using blue-black ink staining and scanning electrochemical microscopy (SECM). The blue-black ink staining method was used for the first time to develop three types (sebaceous, natural and eccrine) of LFPs/PVDF based on the difference in wettability between the fingerprint residues and PVDF membrane. The enhanced fingerprints clearly displayed levels 1-3 features with high contrast and low background interference. Furthermore, we achieved chemical imaging of the LFP/PVDF samples, where their possible visualization mechanisms were ascribed to the electrochemical reactivity of squalene and difference in wettability between the LFP and PVDF membrane, which was first proposed and investigated by SECM imaging and water contact angle (WCA) measurements, respectively. Significantly, SECM imaging not only provided fingerprint patterns without any labelling but also revealed the spatial distribution information of squalene in LFPs simultaneously. In addition, it was also demonstrated that LFPs deposited on various surfaces were first successfully transferred to the PVDF membrane, and then further developed with both methods, making them general for personal identity-related applications. Taken together, the blue-black ink staining method can easily and quickly obtain level 3 features of LFPs/PVDF and the SECM approach can non-invasively image the topography and chemical information of LFPs/PVDF, and thus they can be potentially selected according to various requirements in forensic scenarios.

Post-imprinting modification: electrochemical and scanning electrochemical microscopy studies of a semi-covalently surface imprinted polymer

Herein we described a post-imprinting modification of the imprinted molecular cavities for electrochemical sensing of a target protein. Imprinted molecular cavities were generated by following the semi-covalent surface imprinting approach. These mesoporous cavities were modified with a ferrocene 'electrochemical' tracer for electrochemical transduction of the target protein recognition. Electrochemical sensors prepared after post-imprinting modification showed a linear response in the concentration range of 0.5 to 50 μM. Chemosensors fabricated based on capacitive impedimetric transduction demonstrated that imprinted molecular cavities without post-imprinting modification showed better selectivity. Scanning electrochemical microscopy (SECM) was used for the surface characterization of imprinted molecular cavities modified with ferrocene electrochemical tracers. SECM analysis performed in the feedback mode monitor changes in the surface state of the ferrocene-modified polymer film. The kinetics of the mediator regeneration was almost 1.8 times higher on the non-imprinted surface versus the post-imprinting modified molecular imprinted polymer.

Nano-Electrochemical Characterization of a 3D Bioprinted Cervical Tumor Model

Current cancer research is limited by the availability of reliable in vivo and in vitro models that are able to reproduce the fundamental hallmarks of cancer. Animal experimentation is of paramount importance in the progress of research, but it is becoming more evident that it has several limitations due to the numerous differences between animal tissues and real, in vivo human tissues. 3D bioprinting techniques have become an attractive tool for many basic and applied research fields. Concerning cancer, this technology has enabled the development of three-dimensional in vitro tumor models that recreate the characteristics of real tissues and look extremely promising for studying cancer cell biology. As 3D bioprinting is a relatively recently developed technique, there is still a lack of characterization of the chemical cellular microenvironment of 3D bioprinted constructs. In this work, we fabricated a cervical tumor model obtained by 3D bioprinting of HeLa cells in an alginate-based matrix. Characterization of the spheroid population obtained as a function of culturing time was performed by phase-contrast and confocal fluorescence microscopies. Scanning electrochemical microscopy and platinum nanoelectrodes were employed to characterize oxygen concentrations-a fundamental characteristic of the cellular microenvironment-with a high spatial resolution within the 3D bioprinted cervical tumor model; we also demonstrated that the diffusion of a molecular model of drugs in the 3D bioprinted construct, in which the spheroids were embedded, could be measured quantitatively over time using scanning electrochemical microscopy.

Multifrequency dielectric mapping of fixed mice colon tissues in cell culture media via scanning electrochemical microscopy

Alternating current scanning electrochemical microscopy (AC-SECM) is a powerful tool for characterizing the electrochemical reactivity of surfaces. Here, perturbation in the sample is induced by the alternating current and altered local potential is measured by the SECM probe. This technique has been used to investigate many exotic a range of biological interfaces including live cells and tissues, as well as the corrosive degradation of various metallic surfaces, etc. In principle, AC-SECM imaging is derived from electrochemical impedance spectroscopy (EIS) which has been used for a century to describe interfacial and diffusive behaviour of molecules in solution or on a surface. Increasingly bioimpedance centric medical devices have become an important tool to detect evolution of tissue biochemistry. Predictive implications of measuring electrochemical changes within a tissue is one of the core concepts in developing minimally invasive and smart medical devices. In this study, cross sections of mice colon tissue were used for AC-SECM imaging. A 10 micron sized platinum probe was used for two-dimensional (2D) tan δ mapping of histological sections at a frequency of 10 kHz, Thereafter, multifrequency scans were performed at 100 Hz, 10 kHz, 300 kHz, and 900 kHz. Loss tangent (tan δ) mapping of mice colon revealed microscale regions within a tissue possessing a discrete tan δ signature. This tan δ map may be an immediate measure of physiological conditions in biological tissues. Multifrequency scans highlight subtle changes in protein or lipid composition as a function of frequency which was recorded as loss tangent maps. Impedance profile at different frequencies could also be used to identify optimal contrast for imaging and extracting the electrochemical signature specific for a tissue and its electrolyte.

In situ characterisation for nanoscale structure-performance studies in electrocatalysis

Recently, electrocatalytic reactions involving oxygen, nitrogen, water, and carbon dioxide have been developed to substitute conventional chemical processes, with the aim of producing clean energy, fuels and chemicals. A deepened understanding of catalyst structures, active sites and reaction mechanisms plays a critical role in improving the performance of these reactions. To this end, in situ/operando characterisations can be used to visualise the dynamic evolution of nanoscale materials and reaction intermediates under electrolysis conditions, thus enhancing our understanding of heterogeneous electrocatalytic reactions. In this review, we summarise the state-of-the-art in situ characterisation techniques used in electrocatalysis. We categorise them into three sections based on different working principles: microscopy, spectroscopy, and other characterisation techniques. The capacities and limits of the in situ characterisation techniques are discussed in each section to highlight the present-day horizons and guide further advances in the field, primarily aiming at the users of these techniques. Finally, we look at challenges and possible strategies for further development of in situ techniques.

Autonomous Non-Equilibrium Self-Assembly and Molecular Movements Powered by Electrical Energy

The ability to exploit energy autonomously is one of the hallmarks of life. Mastering such processes in artificial nanosystems can open technological opportunities. In the last decades, light- and chemically driven autonomous systems have been developed in relation to conformational motion and self-assembly, mostly in relation to molecular motors. In contrast, despite electrical energy being an attractive energy source to power nanosystems, its autonomous harnessing has received little attention. Herein we consider an operation mode that allows the autonomous exploitation of electrical energy by a self-assembling system. Threading and dethreading motions of a pseudorotaxane take place autonomously in solution, powered by the current flowing between the electrodes of a scanning electrochemical microscope. The underlying autonomous energy ratchet mechanism drives the self-assembly steps away from equilibrium with a higher energy efficiency compared to other autonomous systems. The strategy is general and might be extended to other redox-driven systems.

In Situ and Quantitatively Monitoring the Dynamic Process of Ferroptosis in Single Cancer Cells by Scanning Electrochemical Microscopy

Ferroptosis, as a promising therapeutic strategy for cancers, has aroused great interest. Quantifying the quick dynamic changes in key parameters during the early course of ferroptosis can provide insights for understanding the underlying mechanisms of ferroptosis and help the development of therapies targeting ferroptosis. However, in situ and quantitatively monitoring the quick responses of living cancer cells to ferroptosis at the single-cell level remains technically challenging. In this work, we selected HuH7 cells (hepatocellular carcinoma (HCC) cells) as a cell model and Erastin as a typical ferroptosis inducer. We utilized scanning electrochemical microscopy (SECM) to quantitatively and in situ monitor the early course of ferroptosis in HuH7 cells by characterizing the three key parameters of cell ferroptosis (i.e., cell membrane permeability, respiratory activity, and the redox state). The SECM results show that the membrane permeability of ferroptotic HuH7 cells continuously increased from 0 to 8.1 × 10-5 m s-1, the cellular oxygen consumption was continuously reduced by half, and H2O2 released from the cells exhibited periodic bursts during the early course of ferroptosis, indicating the gradually destroyed cell membrane structure and intensified oxidative stress. Our work realizes, for the first time, the in situ and quantitative monitoring of the cell membrane permeability, respiratory activity, and H2O2 level of the early ferroptosis process of a single living cancer cell with SECM, which can contribute to the understanding of the physiological process and underlying mechanisms of ferroptosis.

A nanoelectrode-based study of water splitting electrocatalysts

The development of low-cost and efficient catalytic materials for key reactions like water splitting, CO₂ reduction and N₂ reduction is crucial for fulfilling the growing energy consumption demands and the pursuit of renewable and sustainable energy. Conventional electrochemical measurements at the macroscale lack the potential to characterize single catalytic entities and nanoscale surface features on the surface of a catalytic material. Recently, promising results have been obtained using nanoelectrodes as ultra-small platforms for the study of the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) on innovative catalytic materials at the nanoscale. In this minireview, we summarize the recent progress in the nanoelectrode-based studies on the HER and OER on various nanostructured catalytic materials. These electrocatalysts can be generally categorized into two groups: 0-dimensional (0D) single atom/molecule/cluster/nanoparticles and 2-dimensional (2D) nanomaterials. Controlled growth as well as the electrochemical characterization of single isolated atoms, molecules, clusters and nanoparticles has been achieved on nanoelectrodes. Moreover, nanoelectrodes greatly enhanced the spatial resolution of scanning probe techniques, which enable studies at the surface features of 2D nanomaterials, including surface defects, edges and nanofacets at the boundary of a phase. Nanoelectrode-based studies on the catalytic materials can provide new insights into the reaction mechanisms and catalytic properties, which will facilitate the pursuit of sustainable energy and help to solve CO₂ release issues.

Anaerobic Infrared Spectroelectrochemical Methods for Studying Oxygen-Sensitive [FeFe] Hydrogenases

[FeFe] hydrogenases comprise an important class of H₂ evolving enzymes; however, these proteins are often oxygen sensitive and require anaerobic environments for characterization. Understanding the electrochemical relationships between various active and inactive states of these enzymes is instrumental in uncovering the reaction mechanisms of the complex six-iron active center of [FeFe] hydrogenases called H-cluster. Since states of the H-cluster exhibit distinct fingerprint-like spectra in the mid-IR range, IR spectroelectrochemical experiments provide a powerful methodological framework for this goal. This chapter describes protocols for performing Fourier-transform infrared (FTIR) spectroelectrochemical experiments on [FeFe] hydrogenases under anaerobic conditions. Topics included experimental design, data acquisition, and data analysis.