Structural Design of a Cellulose-Based Solid Amine Adsorbent for the Complete Removal and Colorimetric Detection of Cr(VI)

Efficient preparation of anisotropic cellulose sponge from cotton stalks: An excellent material for separation applications

Water pollution and solid waste resource reuse demand immediate attention and research. Here, we present a method to create anisotropic cellulose sponges from cotton stalk waste. Using the inherent structure of cotton stalks, we selectively remove lignin and hemicellulose via acid and alkali pretreatment. This process yields cellulose sponges with a natural pore structure. Our findings demonstrate that these sponges retain the original pore configuration of cotton stalks, providing excellent connectivity and compressibility due to their unique anisotropic three-dimensional structure. Moreover, these sponges exhibit exceptional super-hydrophilic and underwater super-oleophobic properties, with underwater oil contact angles exceeding 150° for all tested oils. External pressure can reduce the pore size of the cellulose sponge, facilitating the gravity-driven separation and removal of dyes and emulsions. Remarkably, removal efficiencies for Methylene Blue (MB), Congo Red (CR), water-in-oil (w/o) emulsions, and oil-in-water (o/w) emulsions exceed 99 %, 97 %, 99 %, and 99 %, respectively, highlighting superior removal and recyclability. Further investigation into the mechanisms of dye and emulsion removal employs X-ray photoelectron spectroscopy (XPS) characterization and molecular dynamics (MD) simulation. These insights lay the groundwork for the efficient recycling and resource utilization of waste cotton stalks, offering promising applications in water purification.

Adsorption of hexavalent chromium from wastewater using polyaniline-coated microcrystalline cellulose nanocomposites

In this study, the effectiveness of microcrystalline cellulose (MCC) as an adsorbent for the removal of hexavalent chromium, Cr(vi), from synthetic wastewater was enhanced through functionalization with polyaniline (PANI). Scanning electron microscopy (SEM) showed that MCC was an effective scaffold for in situ chemical oxidative polymerization of aniline. Fourier transform infrared spectroscopy (FTIR) spectroscopy and X-ray diffraction confirmed successful PANI synthesis. The MCC/PANI nanocomposites exhibited relatively high specific surface areas, compared to that of the MCC (2.05 m2 g-1). Batch adsorption studies showed that the optimal conditions for the removal of Cr(vi) from wastewater using the MCC/PANI-69 wt% nanocomposite were an initial Cr(vi) concentration of 100 mg L-1, an adsorbent dosage of 4 g L-1 and a Cr(vi) solution pH of 7. The MCC/PANI-69 wt% required only 30 min to reach equilibrium and the equilibrium removal efficiency was 95%. FTIR spectroscopy and energy dispersive X-ray spectrometry results suggest that the Cr(vi) removal mechanism by the MCC/PANI-69 wt% nanocomposite at pH 7 was through electrostatic attraction of Cr(vi) species by PANI, reduction of Cr(vi) into Cr(iii) and precipitation of Cr(iii) on the nanocomposite surface. The kinetics for the removal of the Cr(vi) by the MCC/PANI-69 wt% nanocomposite were adequately described by the pseudo second order (PSO) kinetics model, whereas the Langmuir isotherm adequately described the equilibrium data. The MCC/PANI-69 wt% nanocomposite had a significantly improved maximum adsorption capacity of 35.97 mg g-1, at pH 7, in comparison to that of the MCC (3.92 mg g-1 at pH 1). The study demonstrated that, whereas most of the reported adsorbents for Cr(vi) are only effective at low pH values, the MCC/PANI nanocomposite synthesized in this study was effective at pH 7.

A dual pH- and temperature-responsive hydrogel produced in situ crosslinking of cyclodextrin-cellulose for wound healing

Cellulose hydrogels have gained attention in the field of wound healing due to their biodegradability, biocompatibility, and the capacity to sustain a humid environment that promotes healing. Conventional cellulose hydrogels were usually lacked responsiveness to changing wound conditions, and limited capacity for controlled release of active substances. The composite hydrogels with Berberine (BBR) loading were prepared from bamboo parenchymal cellulose and in situ crosslinking carboxylated-β-cyclodextrin (BPCH-B) via dissolution. The inclusion of BBR enhanced the antibacterial properties of cellulose hydrogel while maintaining biocompatibility and drug delivery capabilities. The dual-responsive dressing was demonstrated to modulate drug release kinetics in accordance with the pH and temperature conditions prevailing within the wound site. Specifically, study exhibited a significant increase in drug release (over 70 %) under alkaline pH (7.6) and temperature (40 °C) conditions. Full-thickness wound healing experiments indicated that BPCH-B had better healing ability, and the wound healing area of BPCH-B treated was 80 % within 12 days, while the control group was only 50 %. This strategy for generating functional wound healing can be further control release of drug compounds for treatment of wounds, enabling development of practical wound care materials.

Smart antimicrobial Pickering emulsion stabilized by pH-responsive cellulose-based nanoparticles

Responsive antimicrobial materials can control and slow the release of antimicrobial agents smartly by responding to the stimulation of environmental conditions. In this study, we designed the pH-responsive cellulose-based nanoparticles (TOCNC-g-PEI) with amino and carboxyl groups by grafting polyethyleneimine (PEI) to carboxylated cellulose nanocrystals. Finally, the Pickering emulsion was endowed with smart antimicrobial properties by emulsifying the oregano essential oil (OEO) with nanoparticles. The TOCNC-g-PEI₂₅₀₀₀ had uniform size, greater dispersion, and excellent antimicrobial properties. The contact angles of nanoparticles were 78.70 ± 1.13°, 55.80 ± 1.58° and 55.35 ± 1.56° at neutral conditions, pH 4.0 and 8.0, respectively. The nanoparticles were responding to pH stimulation. The developed emulsion (4:6, 1.30 wt%) had exceptionally stabilized and encapsulated 98.56 ± 1.22 % of the oil phase. The OEO released rapidly within 0-12 h and slowly at 12-36 h. The cumulative release rates quickly reached 93.60 ± 3.73 % (pH 4.0) and 83.25 ± 0.36 % (pH 8.0) and stabilized gradually. The antimicrobial rates of emulsion stimulated for 4 h reached 100 % at pH 4.0, and both of them exceeded 96.10 ± 2.49 % at pH 8.0. The response of Pickering emulsion to pH stimulating controlled release antimicrobial agents and achieved smart antimicrobial.

Remediation of water tainted with noxious hexavalent chromium using cetylpyridinium-modified bagasse biomass: adsorption and regeneration studies

Herein, cetylpyridinium-modified bagasse (SB-CPC) biomass was synthesized and applied for removal of noxious Cr(VI) ions from aqueous matrix. Batch mode analyses were conducted, and the results showed that SB-CPC adsorbent has a maximum uptake capacity (q_m) of 70.5 ± 3.2 mg g^-1 at 303 K. The adsorption isotherms and kinetics for elimination of Cr(VI) by SB-CPC were better fitted by Langmuir model and pseudo-second-order model, respectively. The occurrence of pseudo-second-order kinetic could be mainly influenced by the intra-particle diffusion mass transfer. Electrostatic attraction was the dominant underlying reaction mechanism followed by pore filing effect (minor). Thermodynamic study affirms the endothermic behavior and occurrence of physical adsorption process. SB-CPC adsorbent had exhibited an outstanding desorption-regeneration performance using NaOH solution; accordingly, it can practically be applied for remediation of wastewater tainted with Cr(VI) ions.

Advances in Sorptive Removal of Hexavalent Chromium (Cr(VI)) in Aqueous Solutions Using Polymeric Materials

Sorptive removal of hexavalent chromium (Cr(VI)) bears the advantages of simple operation and easy construction. Customized polymeric materials are the attracting adsorbents due to their selectivity, chemical and mechanical stabilities. The mostly investigated polymeric materials for removing Cr(VI) were reviewed in this work. Assembling of robust functional groups, reduction of self-aggregation, and enhancement of stability and mechanical strength, were the general strategies to improve the performance of polymeric adsorbents. The maximum adsorption capacities of these polymers toward Cr(VI) fitted by Langmuir isotherm model ranged from 3.2 to 1185 mg/g. Mechanisms of complexation, chelation, reduction, electrostatic attraction, anion exchange, and hydrogen bonding were involved in the Cr(VI) removal. Influence factors on Cr(VI) removal were itemized. Polymeric adsorbents performed much better in the strong acidic pH range (e.g., pH 2.0) and at higher initial Cr(VI) concentrations. The adsorption of Cr(VI) was an endothermic reaction, and higher reaction temperature favored more robust adsorption. Anions inhibited the removal of Cr(VI) through competitive adsorption, while that was barely affected by cations. Factors that affected the regeneration of these adsorbents were summarized. To realize the goal of industrial application and environmental protection, removal of the Cr(VI) accompanied by its detoxication through reduction is highly encouraged. Moreover, development of adsorbents with strong regeneration ability and low cost, which are robust for removing Cr(VI) at trace levels and a wider pH range, should also be an eternally immutable subject in the future. Work done will be helpful for developing more robust polymeric adsorbents and for promoting the treatment of Cr(VI)-containing wastewater.

Biocomposite based on zirconium and amine-grafted walnut shell with antibacterial properties for the removal of Alizarin red in water: batch and column studies

Recent progress has been made in the application of novel zirconium-loaded amine-grafted walnut shells as multifunctional adsorbents for the remediation of Alizarin red (AR) and bacteria in aqueous solutions. The morphology and functional groups of ACWNS@Zr were studied using Brunauer-Emmett-Teller (BET) techniques, X-ray diffraction (XRD), pH point of zero charges (pHpzc), scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy. Adsorption and regeneration tests were carried out in batch and column mode. The ACWNS@Zr had a Langmuir maximum capacity of 415.5 ± 6.1 mg g^-1 at 303 K. The spread plate technique was used to evaluate the adsorbent's antimicrobial properties against Staphylococcus aureus and Escherichia coli. ACWNS@Zr exhibited inhibitory potential towards S. aureus and E. coli in the suspensions by 53.3% and 15.0%, respectively. Electrostatic interaction and complexation interaction could be the key mechanisms governing AR dye removal. Equilibrium isotherms fit Langmuir models better for both batch and column studies, while adsorption kinetics to pseudo-second-order and Thomas models for batch and column studies, respectively. Thermodynamic studies indicated that the adsorption process was endothermic and spontaneous. Furthermore, columns' mass transfer capacity (B) increased as the concentration increased due to the enhanced driving force for AR adsorption onto ACWNS@Zr. Regeneration with NaOH solution of AR-loaded ACWNS@Zr was remarkable.

Synthesis of cellulose II-based spherical nanoparticle microcluster adsorbent for removal of toxic hexavalent chromium

Since natural cellulose is mostly cellulose I and has a fibrous form, most cellulose-based adsorbents are fibrous/rod-shaped and exhibit the cellulose I crystal structure. This study reports a cellulose II-based spherical nanoparticle microcluster adsorbent (SNMA), synthesized from biomass by a bottom-up approach, for removing toxic hexavalent chromium (Cr(VI)). The basic structure of SNMA was investigated. Notably, the prepared adsorbent was a microcluster composed of spherical nanoparticles, while exhibiting cellulose II crystal structure, resulting in higher thermal stability and significantly enhanced adsorption performance. The adsorption process and mechanism of SNMA on Cr(VI) were studied in detail. The SNMA achieved a high adsorption capacity (225.94 mg/g) and receptor site density. The SNMA is expected to be used as a bio-based spherical nanoparticle microcluster adsorbent platform for the adsorption of different toxic substances by changing the surface functional groups of its components, spherical nanoparticles.

Construction of 2D/2D MoS2/g-C3N4 Heterostructures for Photoreduction of Cr (VI)

2D/2D MoS₂/g-C₃N₄ (MCN) surface heterostructures were created by second thermal polymerization of bulk g-C₃N₄ and the reaction of thiourea and MoO₃ at 670 °C. MoS₂ networks grew vertically along the (002) facet on superior thin g-C₃N₄ nanosheets. The layered heterostructures drastically improved the Cr(VI) removal ability. In the dark case, 27% of Cr(VI) was removed within 45 min. The result indicates that the adsorption of Cr(VI) was a chemical adsorption process involving the sharing and transfer of electrons. The equilibrium data indicate that the adsorbent was covered with a monolayer adsorbate, which conformed to the Langmuir isotherm model (R² = 0.9618). In addition, MCN nanocomposites could convert Cr(VI) into non-toxic Cr(III) by photoreduction under visible light irradiation. With an optimized composition, 100% of Cr(VI) was removed within 30 min, which was ∼10 times quicker compared with Cr(VI) removal under dark conditions. Because g-C₃N₄ nanosheets (sample CN₆₇₀) with higher photocurrent density revealed the lowest photoreduction Cr(VI) ability, adsorption plays an important role in Cr(VI) removal. For MoS₂/g-C₃N₄ nanocomposites used in Cr(VI) removal, adsorption and photoreduction were incorporated together to get excellent performance.

Insight into the adsorption of Cr(vi) on functionalized carboxymethyl cellulose-based sponge via experimental and theoretical calculations

PEI–PAM–CM with a sponge-like structure can effectively remove Cr(vi) at low concentration by electrostatic attraction and chemical binding.

A biomass-assembled macro/meso-porous nano-scavenger for Hg ion trapping

Simple self-assembling functional biomass to fabricate porous supramolecular networks for efficient removal of Hg ions.

Temperature/pH Smart Nanofibers with Excellent Biocompatibility and Their Dual Interactions Stimulus-Responsive Mechanism

Novel nanosized biomass-based pH- and temperature-responsive cellulose nanofibers (TOCNF-HPEI-IBAm) were designed and prepared by grafting hyperbranched polyethylenimine (HPEI) modified with isobutyramide (IBAm) groups (HPEI-IBAm) onto carboxylated cellulose nanofibers (TOCNFs). The as-prepared TOCNF-HPEI-IBAm possessed excellent biocompatibility and pH- and temperature-responsive properties. TOCNF-HPEI-IBAm showed a rapid wettability conversion from hydrophilic (WCA = 41.1°, WCA = 70.7°) to hydrophobic (WCA = 147.3°, WCA = 142.2°) in response to changes in pH and temperature from acidic conditions to alkaline conditions and from lower to higher temperatures. In addition, it possesses strong antibacterial activity against Escherichia coli and Listeria (Eb ≥ 97%). The amount of DOX loaded in TOCNF-HPEI-IBAm was 642.52 mg/g, and the maximum amount of DOX released was 39.30% at pH = 3.0 within 9 h. Furthermore, the dual interactions stimulus-responsive mechanism was revealed to be attributed to the expansion and collapse of the molecular chains of TOCNF-HPEI-IBAm in response to temperature and pH through mutual promotion and inhibition.

Efficient removal of Cr(VI) from water by the uniform fiber ball loaded with polypyrrole: Static adsorption, dynamic adsorption and mechanism studies

A novel adsorbent, the uniform fiber ball (UFB) loaded with polypyrrole (UFB-PPy), was synthesized for Cr(VI) removal from water in this paper. The structure of the UFB and UFB-PPy were characterized by SEM, EDS, FT-IR, BET, XPS and TG. The adsorption properties of UFB-PPy towards Cr(VI) were investigated by the effects of temperature, initial concentration of Cr(VI), interfering ions and contact time in batch experiments, the isothermal models (Langmuir, Freundlich and Temkin) and the kinetic models (Pseudo first-order kinetic, Pseudo second-order kinetic and Intra-particle diffusion models) were used to describe the adsorption behavior. The effects of the initial concentration and flow rate of the Cr(VI) solution in the column experiments were also studied, and the dynamic models (Yoon-Nelson, Adams-Bohart and Wolborska model) were applied to predict the adsorption performance. The Cr(VI) removal mechanism of UFB-PPy was revealed by studying the effect of pH on adsorption, testing of Cl^-, and analyzing the XPS. The results showed that UFB-PPy exhibited excellent adsorption properties for Cr(VI) both in batch and column adsorption. The possible adsorption mechanism involved electrostatic attraction, ion exchange and reduction. Conveniently, the chromium resources can be recovered with the form of high-purity Cr₂O₃ by simple calcination of Cr(VI)-captured UFB-PPy (UFB-PPy-Cr).

Intelligent Cellulose Nanofibers with Excellent Biocompatibility Enable Sustained Antibacterial and Drug Release via a pH-Responsive Mechanism

Novel nanosized biomass-based pH-responsive cellulose nanofibers (CNF-PEI) with excellent biocompatibility were tailored by grafting polyethylenimine (PEI) onto carboxylated cellulose nanofibers (CNF-COOH); the active site (-COOH, 0.96 mmol/g) was anchored on cellulose nanofibers (CNFs) to introduce PEI with a high density (10.57 mmol/g) of amino groups. The as-prepared CNF-PEI not only maintained the good properties of CNFs but also possessed excellent biocompatibility and pH-responsive properties, offering interesting possibilities for pH-induced sustained drug release and medical dressing. The CNF-PEI showed rapid wettability conversion from hydrophilic, underwater superoleophobic (WCA = 20.7°, OCA = 159.3°) to hydrophobic, superoleophilic (WCA = 129.6°, OCA = 29.7°) in response to pH change from acidic conditions to alkaline conditions. The antibacterial activity of CNF-PEI toward Escherichia coli and Listeria monocytogenes was 100% and 94.6% under acidic conditions, respectively. Furthermore, the pH-responsive mechanism of CNF-PEI was revealed by XPS, ¹³C NMR, ¹H NMR, and AFM analyses.