Fabricating Bionic Ultraslippery Surface on Titanium Alloys with Excellent Fouling-Resistant Performance

Detection of Nanobubbles on Lubricant-Infused Surfaces Using AFM Meniscus Force Measurements

So far, the presence of nanobubbles on lubricant-infused surfaces (LIS) has been overlooked, because of the difficulty in detecting them in such a complex system. We recently showed that anomalously large interfacial slip measured on LIS is explained by the presence of nanobubbles [Vega-Sánchez, Peppou-Chapman, Zhu and Neto, Nat. Commun., 2022 13, 351]. Crucial to drawing this conclusion was the use of atomic force microscopy (AFM) force-distance spectroscopy (meniscus force measurements) to directly image nanobubbles on LIS. This technique provided vital direct evidence of the spontaneous nucleation of nanobubbles on lubricant-infused hydrophobic surfaces. In this paper, we describe in detail the data collection and analysis of AFM meniscus force measurements on LIS and show how these powerful measurements can quantify both the thickness and distribution of multiple coexisting fluid layers (i.e., gas and oil) over a nanostructured surface. Using this technique, thousands of force curves were automatically analyzed. The results show that the interfacial tension of the nanobubbles is reduced from 52 ± 9 mN m^-1 to 39 ± 4 mN m^-1 by the presence of the silicone oil layer.

Slippery 3-dimensional porous bioabsorbable membranes with anti-adhesion and bactericidal properties as substitute for vaseline gauze

Vaseline gauze is a common type of wound dressing that consist of absorbent gauze impregnated with white petrolatum. It has excellent anti-adhesive property which can reduce trauma during dressing changes. However, this kind of wound dressing doesn't have bacterial killing property. Thus, a new kind of wound dressing that has anti-adhesive and bactericidal properties is needed urgently. Creating slippery liquid-impregnated porous surfaces (SLIPS) that insensitive to the structure of porous solid are generally viewed as a new anti-adhesion strategy. To expand the potential utility of SLIPS as substitute for vaseline gauze, dual-functional slippery membranes with anti-adhesion and bactericidal properties by using triclosan, vegetable oils and polylactic acid (PLA) were prepared. It's demonstrated that the triclosan-loaded/vegetable oils-infused PLA membranes (T/V-PM) has good cytocompatibility in vitro. Notably, the T/V-PM can gradually release biocide molecule into surrounding aqueous media. Moreover, the T/V-PM can kill planktonic bacterial cells without loss of their antifouling property. The in vivo study revealed that the T/V-PM can prevent the secondary injuries during wound dressing changes. This simple and low-cost strategy can be applied to inhibit blood and bacterial adhesion, and prevent tissue adhesion at the wound site. It's confirmed that the T/V-PM have great potential as substitute for vaseline gauze.

Designing a Highly Stable Slippery Organogel on Q235 Carbon Steel for Inhibiting Microbiologically Influenced Corrosion

Microbiologically influenced corrosion (MIC) accelerates the corrosion and degradation of metal materials due to the settlement of microorganisms on the surface. However, environmentally friendly and efficient methods to fabricate antifouling and anticorrosion surfaces are still lacking. Inspired by Nepenthes, a slippery liquid-infused porous surface (SLIPS) has been proven to be an efficient way to inhibit settlement of microorganisms on the metal surface and the following MIC due to the existence of a mobile defect-free lubricant layer. However, the stability of the lubricant layer and substrate of the SLIPS prevented its long-term antifouling and anticorrosion application. Herein, a highly stable slippery organogel was fabricated by depositing a homogeneous mixture of PDMS (base and curing agent), silicone oil, triethoxyvinylsilane, and SiO₂ on Q235 and curing in an oven. Triethoxyvinylsilane was not only able to cross-link with the curing agent of PDMS through hydrosilylation but also able to interlink the organogel and Q235 through condensation between the -OH of the metal surface and hydrolyzed siloxane. As a result, the adhesion force between the organogel without triethoxyvinylsilane and the substrate (0.45 MPa) increased to 1.50 MPa for the organogel with triethoxyvinylsilane and SiO₂. Also, the tensile strength of the organogel without SiO₂ (0.97 MPa) increased to 3.88 MPa for the organogel with 2 wt % SiO₂ because of the high elastic modulus of SiO₂, which was important to improving its stability under external force. In addition, the organogel showed stable oil distribution and slippery performance after spinning at 4000 rpm for 30 s. Then, the bacterial settlement demonstrated that the organogel could effectively inhibit Pseudoalteromonas sp. settlement on the substrate under both static and dynamic conditions. Finally, an electrochemical test indicated that the MIC could be effectively mitigated by the organogel. This study provides an efficient method to fabricate a highly stable slippery surface on a metal surface for its potential application in mitigating MIC.

Understanding and optimizing the antibacterial functions of anodized nano-engineered titanium implants

Nanoscale surface modification of titanium-based orthopaedic and dental implants is routinely applied to augment bioactivity, however, as is the case with other cells, bacterial adhesion is increased on nano-rough surfaces. Electrochemically anodized Ti implants with titania nanotubes (TNTs) have been proposed as an ideal implant surface with desirable bioactivity and local drug release functions to target various conditions. However, a comprehensive state of the art overview of why and how such TNTs-Ti implants acquire antibacterial functions, and an in-depth knowledge of how topography, chemistry and local elution of potent antibiotic agents influence such functions has not been reported. This review discusses and details the application of nano-engineered Ti implants modified with TNTs for maximum local antibacterial functions, deciphering the interdependence of various characteristics and the fine-tuning of different parameters to minimize cytotoxicity. An ideal implant surface should cater simultaneously to ossoeintegration (and soft-tissue integration for dental implants), immunomodulation and antibacterial functions. We also evaluate the effectiveness and challenges associated with such synergistic functions from modified TNTs-implants. Particular focus is placed on the metallic and semi-metallic modification of TNTs towards enabling bactericidal properties, which is often dose dependent. Additionally, there are concerns over the cytotoxicity of these therapies. In that light, research challenges in this domain and expectations from the next generation of customizable antibacterial TNTs implants towards clinical translation are critically evaluated. STATEMENT OF SIGNIFICANCE: One of the major causes of titanium orthopaedic/dental implant failure is bacterial colonization and infection, which results in complete implant failure and the need for revision surgery and re-implantation. Using advanced nanotechnology, controlled nanotopographies have been fabricated on Ti implants, for instance anodized nanotubes, which can accommodate and locally elute potent antibiotic agents. In this pioneering review, we shine light on the topographical, chemical and therapeutic aspects of antibacterial nanotubes towards achieving desirable tailored antibacterial efficacy without cytotoxicity concerns. This interdisciplinary review will appeal to researchers from the wider scientific community interested in biomaterials science, structure and function, and will provide an improved understanding of controlling bacterial infection around nano-engineered implants, aimed at bridging the gap between research and clinics.

Depletion of the Lubricant from Lubricant-Infused Surfaces due to an Air/Water Interface

Lubricant-infused surfaces (LIS) have emerged as an innovative way to combat several modern challenges such as biofouling, ice formation, and surface drag. The favorable properties of LIS are dependent on the presence and distribution of a lubricant layer coating the underlying substrate. Unfortunately, this layer is not indefinitely stable and depletes due to external forces. Here, we study how an air/water interface depletes the lubricant from LIS as a function of lubricant wettability on the substrate by varying the chemistry of both the lubricant and the substrate. The lubricants were chosen to represent some of those most commonly used in the literature (silicone oil, perfluoropolyethers, and mineral oil). We use an optical Wilhelmy plate tensiometer to measure the contact angle of the air/water interface on the LIS in situ as the sample is driven through the air/water interface and contact angle hysteresis as a qualitative measure of lubricant depletion. This data is augmented with ex situ quantitative mapping of lubricant thickness using atomic force microscopy (AFM) meniscus force measurements. We find that a thick layer of excess lubricant is always removed in just one dip, regardless of wettability, and that lubricants that do not spread fully on the substrate deplete faster due to their dewetting into droplets. We also find that lubricants that spread onto the air/water interface are more susceptible to depletion. Finally, we investigate the effect of repeated immersions on the properties of liquidlike poly(dimethylsiloxane) (PDMS) chains tethered to glass and find that dynamic contact angles on these surfaces remain constant over several dips and therefore their low hysteresis is unlikely due to unbound polymer.

Design novel three-dimensional network nanostructure for lubricant infused on titanium alloys towards long-term anti-fouling

Titanium alloys, recognized as a marine material with great potential, are currently facing serious biofouling problems, which greatly limits its application range. To improve the antifouling performance of titanium alloys, three unique surface of three-dimensional network, grass-like and linear nanostructures were obtained on titanium alloys via hydrothermal treatment in this work. Further, slippery liquid-infused porous surfaces (SLIPSs) were fabricated on titanium alloys via infusing PFPE lubricant into these nanostructures. Water contact angles and sliding angles of SLIPSs were measured to evaluate the effect of nanostructures on the stability of PFPE lubricant layer. Anti-fouling capability of SLIPSs were investigated by quantifying the cells of chlorella and phaeodactylum tricornutum (P. tricornutum)adhered to titanium alloys. The results shows that all the SLIPSs exhibited remarkable inhibition capacity for the settlement of chlorella and P. tricornutum. Among them, the SLIPS with three-dimensional network nanostructure displayed the longest-term anti-fouling performance, and its reduction rate of P. tricornutum and chlorella reaching 77.2 % and 84.5 % after being cultivated for 21 days, respectively, indicating that there existed a positive correlation between the stability of lubricant layer in the artificial seawater and the antifouling effect.

Inhibition Effectiveness of Laser-Cleaned Nanostructured Aluminum Alloys to Sulfate-reducing Bacteria Based on Superwetting and Ultraslippery Surfaces

This paper is a continued study on laser cleaning removal of marine microbiofouling from Al alloy surfaces. According to our previous study, it is noted that the antifouling functions of the generated laser-cleaned metallic surfaces must be highlighted. In this work, the inhibition effectiveness of the laser-cleaned Al alloy surfaces was evaluated using a type of vital marine microorganism, sulfate-reducing bacteria (SRB) Desulfovibrio desulfuricans subsp. desulfuricans, in a dynamic bacterial solution. Before the immersion tests, the laser-cleaned surfaces with nanostructures were chemically processed into superhydrophilic, superhydrophobic, and ultraslippery surfaces. SRB attachment behaviors as well as inhibition mechanisms of the three surfaces to the SRB settlement were characterized and revealed. The SRB adhering to the above surfaces presented three different morphologies, i.e., broken, dented, and plump cells. Superhydrophilic surfaces unexpectedly showed a not inferior antibacterial ability. A piercing effect of the nanostructures caused nontoxic mechanical damage to the cell membranes. The antiadhesion property of superhydrophobic solid-air hybrid surfaces was unreliable due to the loss of air bubbles. The morphology of the last surviving SRB cells left on the ultraslippery surfaces was basically plump. The stable repellent function of the surfaces was responsible for the vigorous prevention of the adhesion of the SRB. The research results offer an insight into the antibacterial/antiadhesion properties of the laser-cleaned surfaces and a practical value for the periodic service of marine high-end equipment.

WO3-Based Slippery Liquid-Infused Porous Surfaces with Long-Term Stability

Slippery liquid-infused porous surfaces (SLIPS) inspired by Nepenthes pitcher plants exhibit excellent hydrophobicity, antifouling and anti-icing properties, and long-term durability under pressure and temperature. SLIPS have potential applications including in biomedical devices, self-cleaning structures, and water-resistant coatings. A big challenge posed by SLIPS is the durability of the lubricant in the porous layer. Herein, uniform tungsten oxide nanofiber networks were synthesized on the surface of stainless steel through a simple one-step hydrothermal method. WO₃ nanofiber networks on stainless steels were chemically modified, filled with a lubricant, and prepared as SLIPS with excellent liquid repellency and good anti-biofouling properties. The relationship of the nanostructures and the slippery properties of the obtained WO₃-based SLIPS have been investigated in detail in this work. The liquid retention and long-term stability of the SLIPS were characterized using high shear force and water flow impact. We found that the long-term durability of the SLIPS is strongly related to the diameters and the Brunauer-Emmett-Teller surface areas of the WO₃ nanostructures. The durability of the SLIPS is better when the diameter of the WO₃ nanostructures is smaller. The WO₃-based SLIPS prepared in this work exhibit outstanding slippery property, anti-biofouling, and long-term stability under extreme conditions such as high shear rate and water washing and thus may have potential application for surface modification of medical devices in the future.

Durable lubricant-infused coating on a magnesium alloy substrate with anti-biofouling and anti-corrosion properties and excellent thermally assisted healing ability

Inspired by lotus leaves, superhydrophobic surfaces (SHS) have been fabricated by many methods due to their various properties such as self-cleaning, anti-corrosion, and anti-biofouling properties. In recent years, inspired by Nepenthes pitcher plants, the 'slippery liquid-infused porous surface' (SLIPS) has attracted numerous researchers' attention because it not only shows ability corresponding to SHS but also exhibits durability in some aspects due to the continuous and homogeneous liquid-infused surfaces. In this paper, we firstly used a facile hydrothermal method and modification to fabricate SHS on a Mg alloy substrate. After the infusion of a lubricant by a spin-coating method, the transformation from the SHS to SLIPS can be achieved. The SLIPS exhibits an excellent self-cleaning property compared to the SHS, except that the water droplet rolls on the SHS and slides on the SLIPS. Moreover, the SLIPS demonstrates better anti-corrosion and anti-biofouling properties, and is obviously superior to SHS for use on the Mg alloy substrate. The enhanced anti-corrosion and anti-biofouling properties of the SLIPS are because the continuously infused lubricant replaces the air trapped in the micro-pores. Importantly, compared with SHS, the SLIPS shows excellent thermally assisted healing properties. The results of this work indicate that the SLIPS is expected to be an efficient method for improving the water-repellent, self-cleaning, anti-biofouling and anti-corrosion properties of magnesium alloys.

Life and death of liquid-infused surfaces: a review on the choice, analysis and fate of the infused liquid layer

We review the rational choice, the analysis, the depletion and the properties imparted by the liquid layer in liquid-infused surfaces – a new class of low-adhesion surface.

PDMS-Infused Poly(High Internal Phase Emulsion) Templates for the Construction of Slippery Liquid-Infused Porous Surfaces with Self-cleaning and Self-repairing Properties

Advanced liquid-repelling materials that resist both water-based and oil-based contaminants have significant applications in many fields. Herein, a novel protocol for the fabrication of a robust poly(high internal phase emulsion) (polyHIPE)-based slippery liquid-infused porous surface (SLIPS) system with combined self-repairing and self-cleaning properties is developed. Specifically, polystyrene-based polyHIPE (PS-HIPE) membranes with an interconnected porous structure were prepared from polymerization of the continuous oil phase in the water-in-oil HIPE templates. These polyHIPE membranes were used, for the first time, as porous substrates for loading low surface tension silicone oils as lubricating liquids for the fabrication of polyHIPE-based SLIPS membranes. These polyHIPE-based SLIPS membranes could easily repel both water- and oil-based contaminants (e.g., ink, milk, and coffee) with very low sliding angles (3.0 ? 1.3?) and could even repel solid contaminants (e.g., dust) upon washing with water. Meanwhile, such membranes exhibit excellent self-repairing properties so that physical scratching damage, such as cutting a trench, does not affect the liquid-repelling performance. The liquid-repelling ability could be recovered completely within 10 s. More significantly, such a SLIPS membrane shows excellent durability so that the water sliding angle of the SLIPS could be maintained at less than 5.0? for about 80 cycles owing to the regenerated poly(dimethylsiloxane) layer on the surface. This work represents a robust methodology to enrich the development of hydrophobic and oleophobic slippery surfaces, which is promising for many areas, such as biomedical, self-cleaning, antifouling, and self-repairing materials.